MasterCool 43013 Operating instructions

MasterCool
Brand
MasterCool
Model
43013
Type
Operating instructions

This manual is also suitable for

MasterCool 43013 is a vacuum-type cooling system filler kit with a gauge that helps shorten the time needed to refill new coolant by creating a vacuum in the cooling system. The vacuum created sucks coolant into the radiator. It also eliminates the need to bleed air from the cooling system, thereby reducing the risk of engine overheating.

With this kit, you do not have to worry about changing the coolant when it is hot. Simply drain the old coolant from the radiator, hook the gauge underneath the car’s hood, connect an air line to the air connector, and connect the proper adapter or use the provided Universal Radiator Adapter onto the radiator filler neck.

MasterCool 43013 is a vacuum-type cooling system filler kit with a gauge that helps shorten the time needed to refill new coolant by creating a vacuum in the cooling system. The vacuum created sucks coolant into the radiator. It also eliminates the need to bleed air from the cooling system, thereby reducing the risk of engine overheating.

With this kit, you do not have to worry about changing the coolant when it is hot. Simply drain the old coolant from the radiator, hook the gauge underneath the car’s hood, connect an air line to the air connector, and connect the proper adapter or use the provided Universal Radiator Adapter onto the radiator filler neck.

43013 VACUUM-TYPE COOLING SYSTEM FILLER KIT
FEATURES:
• Significantly shortens time for refilling new coolant
by creating a vacuum in the cooling system
• No need to undergo the time-consuming air bleeding
• Minimizes the risks of engine overheating
SAFETY WARNING AND PRECAUTIONS:
• Never change coolant when it is hot
• Wear goggles and gloves during operation
OPERATING INSTRUCTIONS:
CREATE A VACUUM
1. Drain coolant from the radiator.
2. Hook the gauge underneath the car’s hood.
3. Connect an air line to Air Connector (D).
4. Connect the proper adapter or use the Universal
Radiator Adapter (I) provided onto the radiator filler
neck (as in Figure 1).
FIGURE 1
5. Toggle the Air Switch (E) to the ON position and open the
Air Valve (C), while Coolant Valve (F) remains off, to create
a vacuum in the cooling system (as in Figure 2).
OFF
ON
ON
FIGURE 2
PRODUCT PARTS:
A. Gauge
B. Hook
C. Air Valve
D. Air Connector
E. Air Switch
F. Coolant Valve
G. Exhaust Connector
H. Coolant Hose Connector
I. Universal Radiator Adapter
A
B
C
D
E
F
G
H
I
43013-INST
For parts or service contact the service department: 1-888-825-6989
WARNING: This product can expose you to chemicals including lead and Di (2-ethylhexyl) phthalate, which are known to the State of California to cause cancer
and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov
6. When the pressure falls into the range between -50 and -60 cmHg (-20 and -25 inHg), close the Air Valve (C) and
toggle the Air Switch (E) to the OFF position.
7. Leave the gauge on the radiator for approximately 10 minutes to check if there are leaks in the cooling system before
refilling new coolant.
REFILL NEW COOLANT
8. Connect the Coolant Hose to the Coolant
Hose Connector (H).
9. Put the other end of the hose into a container
filled with pre-mixed new coolant.
10. Open the Coolant Valve (F) (while the Air
Valve (C) is closed and the Air Switch (E)
remains OFF), coolant will flow into the
radiator immediately (as in Figure 3).
11. The refilling process is completed when the
gauge reads zero.
12. Before putting the gauge back to the case,
remove the residual coolant in the gauge.
ON
OFF
OFF
FIGURE 3
  • Page 1 1
  • Page 2 2

MasterCool 43013 Operating instructions

MasterCool
Brand
MasterCool
Model
43013
Type
Operating instructions
This manual is also suitable for

MasterCool 43013 is a vacuum-type cooling system filler kit with a gauge that helps shorten the time needed to refill new coolant by creating a vacuum in the cooling system. The vacuum created sucks coolant into the radiator. It also eliminates the need to bleed air from the cooling system, thereby reducing the risk of engine overheating.

With this kit, you do not have to worry about changing the coolant when it is hot. Simply drain the old coolant from the radiator, hook the gauge underneath the car’s hood, connect an air line to the air connector, and connect the proper adapter or use the provided Universal Radiator Adapter onto the radiator filler neck.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents