Agria 3496 Owner's manual

Brand: Agria

Model: 3496

Type: Owner's manual

Page is loading ...

998 115-C agria 3496 011 agria-Werke GmbH • D-74219 Möckmühl • Tel. +(0)6298/39-0 • Telefax +49(0)6298/38111 • e-mail: info@agria.de • Internet: www.agria.de 3

Notice d'utilisation n° 998 115-C 01.12

Before using, read the user advice leaflet

and follow the safety recommendations!

2280_1

Technical characteristics

Snow dozer ................. Ref. 3496 011

Blade width .............................125 cm

3 pivoting positions.............................

pivoting positions .................................

...............................left, centered, right

Weight ........................................ 48 kg

Accessories

1 front ballast approx. 18 kg.................

...................................... Ref. 3228 011

1 pair snow chains for 4.00-8...............

...................................... Ref. 2490 991

1 pair snow chains for 5.0-10...............

...................................... Ref. 2491 981

pair snow chains for

6.50/80-12 .........

...................................... Ref. 3790 911

1 plastic blade .....................................

............................ Ref. agria 3496 921

First-time

assembling

For transport purposes, the

snow dozer is delivered with a

notched lever (22) which is

swung to the rear, thus the

following assembly is required:

Remove bolt (23), (24) and

(25).

Swing the notched lever (22)

towards the front.

Insert bolt (23) with washer

(24) through the stretched hole

on the notched lever and the

hole in the stop bolt.

Assemble the washer (24)

and the nut (25), but don't tighten

them.

Feed the free the end of the

cord (21) through the hole on the

notched lever (22) knot the end

of the cord.

Technical safety recommendations

Before assembling or removing the snow dozer, or when undertaking

maintenace or servicing, stop the machine's engine!

Wear heavy duty shoes!

Be careful of crushing or churning up the ground when turning the snow dozer!

Take care to match the speed to the specific working conditions encountered: if

the machine hits an obstruction, the shock of impact may injure the driver.

Assembly

Assembly and removing from the basic

agria machince

è Basic machine

 Use the prop (2) for assembling and

removing:

Lower the prop and insert the linch pin

(3) into the hole below the intermediate

support.

 For snow clearing, raise the prop and

block it with the linch pin (3) above the

intermediate support.

 On the garden tractor insert the

resiliant spike (16) in the plough handle

and press the support end of the remote

control cord with the handle (15) in the

resiliant spike.

On the tool rail, put the end with the

handle towards the rear within reach of

the hands on the plough handle.

Maintenance and

servicing

Grease all the moving parts,

especially:

- The stop bolt.

- The joints on the notched levers.

- The oscillating sliding surface (6).

To do this, loosen the 3 bolts and tighten

them again after greasing, but not too

tightly; be sure the snow dozer can

oscillate easily.

Tighten the nuts and bolts after a short

period in use, except for the oscillating

clip (7) and the mounting between the

notched lever (23/25) and the stop bolt.

Servicing

Carry out a thorough cleaning.

Add a coat of varnish.

Grease all the moving parts.

Spray all the exposed parts with a

biodegradeable rust proofing agent.

Snow clearing

The snow dozer has 3 pivoting posi-

tions:

- central position

- leaning to the left

- leaning to the right

By pulling on the

cord handle (15)

and by quick,

abrupt braking

movements, pivot

the snow ploug

into the desired

position.

By leaning the snow dozer slightly, the

snow can be evacuated to the side.

Make sure the stop bolt is properly

fitted into the correct hole after pivoting

and after having released the handle.

After pivoting, push the handle back onto

the resiliant spike (on garden tractors

only).

Rollers



 Adjust the rollers (1) so that

the blade only just touches the

ground. The snow dozer must

slide on the rollers.

When the blade starts to become worn

down, adjust the rollers. Always check

that it is properly set before starting snow

clearing.

Plastic blade



lA plastic blade (K) may be added

below the steel blade (S). Pierce the plastic

blade (ref. agria

3496 921

) at the top beside

and flush with the steel blade .

Ballast

 The bearing weight of the snow

dozer can be increased by putting front

ballast on the ballast bar (4).

Snow chains

To improve the grip of the driving wheels,

it is recommended to put on snow chains.









8,5 - 9 mm

1 Snow blade

2 Assembly prop

3 Linch pin

4 Ballast rail

5 Stop bolt

6 Oscilating clip

7 Oscillating screw clip

15 Cord handle

16 Resiliant spike





3400

Snow dozerSnow dozer

Snow dozer

3496 011

Due Use

The snow dozer in conjunction with a

hand-controlled single-axle drive unit,

is constructed solely for snow

clearance as part of the normal

maintenance of parkland and paths

(due use).

Any other type of operation is consi-

dered undue. The manufacturer is not

liable for any damage resulting from

undue use, for which the risk lies with

the user alone.

Due use includes compliance with

manufacturer’s instructions on opera-

tion, maintenance and repair.

Any unauthorized changes to the

snow dozer render manufacturer lia-

bility null and void.

Operating

Instructions

Translation of the original operating instructions

Page is loading ...

Agria 3496 Owner's manual

Brand: Agria

Model: 3496

Type: Owner's manual

Download PDF

report

in other languages

français: Agria 3496 Le manuel du propriétaire
Deutsch: Agria 3496 Bedienungsanleitung
Nederlands: Agria 3496 de handleiding

Agria 3496 Owner's manual

Agria 3496 Owner's manual

in other languages

Related papers

Other documents