Curt Manufacturing 11555 Owner's manual

Curt Manufacturing
Brand
Curt Manufacturing
Model
11555
Type
Owner's manual

Curt Manufacturing 11555 is a trailer hitch designed for use with a Honda CR-V. It has a gross load capacity of 2,000 lbs. when used as a weight-carrying hitch, and a trailer weight capacity of 200 lbs. It is also compatible with ballmounts #55001 and 45501.

The hitch is easy to install, with an estimated installation time of 35 minutes. It comes with all the necessary hardware, including carriage bolts, hex flange nuts, and spacers. The installation process involves enlarging existing holes in the frame rails, reversing fishwire carriage bolts and blocks into the frame rails, and loosely installing the tow hook attachment bolt and spacers before leveling the hitch and installing the tow loop attachment fasteners.

Curt Manufacturing 11555 is a trailer hitch designed for use with a Honda CR-V. It has a gross load capacity of 2,000 lbs. when used as a weight-carrying hitch, and a trailer weight capacity of 200 lbs. It is also compatible with ballmounts #55001 and 45501.

The hitch is easy to install, with an estimated installation time of 35 minutes. It comes with all the necessary hardware, including carriage bolts, hex flange nuts, and spacers. The installation process involves enlarging existing holes in the frame rails, reversing fishwire carriage bolts and blocks into the frame rails, and loosely installing the tow hook attachment bolt and spacers before leveling the hitch and installing the tow loop attachment fasteners.

UNDERBODY PANEL TRIM DIAGRAM
Parts List DESCRIPTION
PART NUMBER
QTY
ITEM CARRIAGE BOLT1/2-13 x 2 1/2 LG.
11 .250 x 1.00 x 2.00" SQUARE HOLE SPACERCM-SP1232 HEX FLANGE NUTHFN 121313 7/16" FISHWIRE7_16 FISHWIRE24 CARRIAGE BOLT7/16-14 x 1 1/22
5HEX FLANGE NUT7/16-1426 .250 x 1.00 x 2.50" SQUARE HOLE SPACERCM-SP11
27
GROSS LOAD CAPACITY WHEN USED AS A WEIGHT CARRYING HITCH: LBS. TRAILER WEIGHT & LBS. TONGUE WEIGHT.
***DO NOT EXCEED VEHICLE MANUFACTURER'S RECOMMENDED TOWING CAPACITY.***
HITCH WEIGHT: LBS.
INSTALL TIME: MINUTES
INSTALL NOTES:
- ENLARGE EXISTING HOLES
- LOWER EXHAUST
- REVERSE FISHWIRE HARDWARE
INSTALLATION STEPS
PERIODICALLY CHECK THIS RECEIVER HITCH TO ENSURE THAT ALL FASTENERS
ARE TIGHT AND THAT ALL STRUCTURAL COMPONENTS ARE SOUND.
Curt Manufacturing Inc., warrants this product to be free of defects in material and/or workmanship at the time of retail purchase by the original purchaser. If the product is found to be defective,
Curt Manufacturing Inc., may repair or replace the product, at their option, when the product is returned, prepaid, with proof of purchase. Alteration to, misuse of, or improper installation of
this product voids the warranty. Curt Manufacturing Inc.'s liability is limited to repair or replacement of products found to be defective, and specifically excludes liability for incidental or
consequential loss or damage.
2,000 200
21
35
HONDA CR-V
1/05/2012
11555
1. If present, remove (10) fasteners and lower underbody panel.
2. Lower exhaust by removing rubber isolators from muffler hangers. (See Rubber Isolator Removal Diagram.)
3. Mark and trim underbody panel. Note: Dimensions are approximate, confirm fit prior to trimming. Use ribs of the underbody
panel as cutting guides. (See underbody panel trim diagram)
4. Enlarge existing hole in both frame rails to allow access for 1.00 X 3.00 spacers to be inserted as shown above.
5. Reverse fishwire carriage bolts and blocks into frame rails.
6. Raise hitch into position. If underbody panel is present you will need to raise it with the hitch.
7. Loosely install tow hook attachment bolt and spacers.
8. Level hitch and install tow loop attachment fasteners and tighten. This must be done to prevent the receiver tube from angling
up when other fasteners are tightened.
9. Loosely install hex flange nuts.
10. Torque all 7/16" hardware to 50 lb-ft. Torque all 1/2" hardware to 75 lb-ft.
11. If present, reattach underbody panel using fasteners removed in Step (1)
12. Raise exhaust back into position and re-install rubber isolators removed in Step 1.
DRIVER SIDE
FRAME RAIL
PASSENGER SIDE
FRAME RAIL
TOW LOOP
3
6
7
5
1
ENLARGE EXISTING HOLES
2
4
DESIGNED FOR USE WITH
BALLMOUNT #55001 / 45501
13.50 in
4.00 in
3.00 in
3.00 in
NOTE: DIMENSIONS ARE
APPROXIMATE, CONFIRM
FIT PRIOR TO TRIMMING
  • Page 1 1

Curt Manufacturing 11555 Owner's manual

Curt Manufacturing
Brand
Curt Manufacturing
Model
11555
Type
Owner's manual

Curt Manufacturing 11555 is a trailer hitch designed for use with a Honda CR-V. It has a gross load capacity of 2,000 lbs. when used as a weight-carrying hitch, and a trailer weight capacity of 200 lbs. It is also compatible with ballmounts #55001 and 45501.

The hitch is easy to install, with an estimated installation time of 35 minutes. It comes with all the necessary hardware, including carriage bolts, hex flange nuts, and spacers. The installation process involves enlarging existing holes in the frame rails, reversing fishwire carriage bolts and blocks into the frame rails, and loosely installing the tow hook attachment bolt and spacers before leveling the hitch and installing the tow loop attachment fasteners.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents