Keys Fitness 980HRS User manual

Keys Fitness
Brand
Keys Fitness
Model
980HRS
Category
Treadmills
Type
User manual

This manual is also suitable for

KEYS
Fitness Products, LP
P.O. Box 551239
Dallas, Texas 75239
www.keysfitness.com
OWNER’S MANUAL
980S / 980HRS
TREADMILL
2
TABLE OF CONTENTS
PAGE
Table of Contents 2
Important Safety Information 3
Before You Start 4
Warm Up Exercises 5
Assembly, Moving Instructions 6
Power Requirements 7
Safety Strap 8
Console Functions and Descriptions 9
Program and Operating Instructions 10, 11
Program Descriptions and Profiles 12
Belt Adjustments and Tension 13
Change to MPH or Km/H 14
Maintenance Instructions 15
Troubleshooting Guide 16
Parts and Diagrams 17, 18,19,20,21
Warranty Registration (Mail In Form) 22
3
Important Safety Information
NING!
1) WARNING: Before using this treadmill or starting any exercise program, consult your physician. This is
especially important for persons over the age of 35 and/or persons with pre-existing health problems. The
manufacturer or distributor assumes no responsibility for personal injury or property damage sustained by or through
the use of this product.
2) WARNING:
To reduce the risk of electrical shock, burns, fire, or other possible injuries to the user, it is important
to review this manual and the following precautions before operation.
SAFETY PRECAUTIONS AND TIPS
It is the owner’s responsibility to ensure that all users of this treadmill have read the Owner’s Manual and are familiar
with warnings and safety precautions.
This treadmill has a user maximum capacity of 250 pounds.
The treadmill should only be used on a level surface and is intended for indoor use only. The treadmill should not
be placed in a garage, patio, or near water and should never be used while you are wet. Bodybreak recommends a
treadmill mat be placed under the treadmill to protect floor or carpet and for easier cleaning.
Follow safety information in regards to plugging in your treadmill. Keep the power cord away from the incline wheels
and do not run the power cord underneath your treadmill. Do not operate the treadmill with a damaged or frayed
power cord.
Wear comfortable, good-quality walking or running shoes and appropriate clothing. Do not use the treadmill with
bare feet, sandals, socks or stockings.
Always straddle the belt and allow it to start moving before stepping onto the belt.
Hold on to handrails when adjusting speed, incline, or other controls.
Always examine your treadmill before using to ensure all parts are in working order.
Allow the belt to fully stop before dismounting.
Pets should be never be allowed near or on the treadmill.
Do not leave children unsupervised near or on the treadmill.
Never operate the treadmill where oxygen is being administered, or where aerosol products are being used.
Never insert any object or body parts into any opening.
For safety and to prevent damage to your treadmill, no more than one person should use the treadmill at a time.
Always unplug the treadmill before cleaning and/or servicing. Service to your treadmill should only be performed by
an authorized service representative, unless authorized and/or instructed by the manufacturer. Failure to follow
these instructions will void the treadmill warranty.
Never leave the treadmill unattended while it is running.
4
Before You Start
Thank you for purchasing a KEYS treadmill! This quality product you have chosen was
designed to meets your needs for cardiovascular exercise.
•
Before you start, please read the Owner’s Manual and become familiar with the
operation of your new treadmill.
•
Remember to take the time to perform the stretching exercises
provided to avoid injury.
•
Do not stand on the walking belt while pressing the Power button or Start/Stop button.
•
Always adjust the speed of the treadmill in small increments as this treadmill is capable
of high speeds.
•
If you are taking medication, consult your physician to see if the medication will affect
your exercise heart rate.
• If you have heart problems, you are not active, and/or are over the age of 50 years, do
not use the pre-set treadmill programs or start an exercise program without first
contacting and receiving approval from your physician.
•
To avoid the risk of electrical shock, always keep the console dry. Do not spill liquids
on the console. KEYS recommends a sealed water bottle for beverages consumed
while using the treadmill.
•
Please review the following drawing below to familiarize yourself with the listed
parts. This manual covers several treadmills, so the one pictured below may not
be identical to your particular model.
5
Warm Up Exercises
NING!
WARM UP FIRST !
Warming up prepares the body for exercise by increasing circulation, supplying more
oxygen to the muscles and raising body temperature. Begin each workout with 5 to 10
minutes of stretching and light exercise to warm up. The drawings on this page show
several forms of basic stretching you may perform before your workouts. Again, consult a
physician before starting this or any other exercise program.
15 Seconds for each
25 Seconds each leg
30 Seconds
25 Seconds
20 Seconds
20 Seconds
20 Seconds
20 Seconds
30 Seconds
20 Seconds
20 Seconds
25 Seconds each leg
5 Times
15 Seconds
5 Seconds X 3 times
6
Assembly, Moving Instructions
Assembly
KEYS treadmills are shipped in one piece and fully assembled. After opening the box, remove
any packing materials from the treadmill. Do not throw away any packing materials until the unit
is working properly. Place the base on a clean, level surface. Make sure the electrical cord will
easily reach an electrical outlet.
Moving
CAUTION ! TO AVOID THE RISK OF INJURY, NEVER ATTEMPT TO MOVE THE TREADMILL WHILE IT IS IN
THE UNFOLDED OPERATING POSITON. TO REDUCE THE POSSIBILITY OF INJURY WHILE LIFTING, BEND
YOUR LEGS AND KEEP YOUR BACK STRAIGHT. AS YOU RAISE THE TREADMILL, LIFT USING YOUR LEGS,
NOT YOUR BACK. IN ORDER TO RAISE OR LOWER THE TREADMILL SAFELY, YOU MUST BE ABLE TO LIFT
45 POUNDS (20KG). IT IS SUGGESTED YOU ALWAYS USE THE AID OF A SECOND PERSON WHEN MOVING
THE TREADMILL.
With the treadmill in the folded locked position (safety latch is engaged), grasp the handrails and place one foot on
base as shown in the illustration below. Next, with a firm grasp on handrails, place one foot on the center of the base
crossbar and carefully tilt the treadmill back until it rolls freely on the wheels. Using extreme caution, move the
treadmill to the desired location. To set the treadmill down, place one foot on the center of the base crossbar and
carefully lower treadmill onto base in resting position. Do not attempt to move the treadmill over an uneven or rough
surface.
7
Power Requirements
WARNING!
IMPROPER CONNECTION OF THE EQUIPMENT GROUNDING CONNECTOR CAN RESULT
IN A RISK OF AN ELECTRIC SHOCK. CHECK WITH A QUALIFIED ELECTRICIAN OR
SERVICE MAN IF YOU ARE IN DOUBT AS TO WHETHER THE PRODUCT IS PROPERLY
GROUNDED. DO NOT MODIFY THE PLUG PROVIDED WITH THE PRODUCT, IF IT WILL
NOT FIT THE OUTLET, HAVE A PROPER OUTLET INSTALLED BY A QUALIFIED
ELECTRICIAN.
This treadmill can be seriously damaged by sudden voltage changes in your home’s electrical power. Voltage
spikes, surges, and noise interference can result from weather conditions or from other appliances being turned on or
off. To reduce the possibility of treadmill damage, always use a surge protector (not included) with your treadmill.
Surge protectors can be purchased at most hardware stores. The manufacturer recommends a single outlet surge
protector with a UL 1449 rating as a Transient Voltage Surge Suppressor (TVSS) with a UL suppressed voltage
rating of 400V or less and an electrical rating of 120VAC, 15 amps.
This treadmill must be grounded to reduce the risk of electrical shock. Grounding provides a path of least resistance
for electric current, should the treadmill malfunction. This treadmill comes with an electrical cord having an
equipment-grounding conductor and a grounding plug. Always plug the power cord into a surge protector, and plug
the surge protector into an appropriate outlet that is properly installed and grounded in accordance with all local
codes and ordinances.
This product is for use on a nominal 120-volt circuit, and has a grounding plug that looks like the plug illustrated in the
drawing (1) below.
8
Console Functions and Descriptions
There are either four or five display windows on the control panel to provide feedback information.
TIME WINDOW
• TIME: Indicates elapsed time after pressing start in minutes and seconds (0-99 minutes, 0-59
seconds)
• INTERVAL TIME:
Indicates countdown in seconds to the next interval starting at 5 seconds and
counting to 0 seconds
SPEED WINDOW
• SPEED: Indicates MPH (miles per hour) or KMH (kilometer per hour) in .1 increments
DISTANCE / CALORIES WINDOW
• DISTANCE: Indicates Miles or Kilometers traveled in .01 increments up to 9.99 and .1 increments
starting at 10.0
•
CALORIES: Indicates estimated calories used based on 150 lb. person at the indicated speed,
incline, and time
INCLINE WINDOW
• INCLINE: Indicates incline in percent of grade 0-12% in 1 increments
• PULSE (980HRS Model Only): Indicates current heart rate
• HEART “♥”
(980HRS Model only): Indicates control panel is receiving a signal from heart rate
transmitter. Heart will blink on and off if receiving signal from Heart Rate Transmitter chest strap.
CENTER BRICKYARD WINDOW (980HRS ONLY)
• Displays quarter mile track in Manual mode. Indicates position on track by a blink. In program
mode, shows the change in speed profile across the interval range (1-10) and shows position with a
blinking action.
•
The 980HRS will display the name of the program selected, showing on the left hand side of the
window. The LAP counter will appear in manual mode in the center of the window.
9
Program and Operating Instructions
QUICK START / MANUAL MODE
•
Plug into a standard wall outlet (110-Volt AC, 15-amp circuit). Attach Safety Key to treadmill console.
• Stand on the treadmill and straddle belt.
• Press POWER button. There will be an eight (8) second delay after pressing the POWER button before data can
be entered. The TIME window will flash.
• Press START/STOP button. Belt will begin to move after 4 seconds. Step on belt slowly after the belt starts
moving. Speed or incline may be adjusted by using the appropriate + (increase) or – (decrease) buttons.
• To end your workout
, press START/STOP button. Belt will gradually slow to zero.
•
To pause your workout, press PAUSE.
• To re-start after pausing: Press the PAUSE button. WARNING: The treadmill belt will resume at the speed the
treadmill was moving before pausing.
• Countdown Time, Preset Speed and/or Incline
: Time, Speed, and Incline may be preset prior to getting
started. After pressing the POWER button, the time window will blink. Use the SPEED/TIME + or – arrows to
select your workout time, then press the ENTER PROGRAM button. The SPEED/TIME window will now be
flashing. Using the same + or – arrows, select the speed for your workout, then press ENTER PROGRAM. Now
the INCLINE window will be flashing. Use the INCLINE + or – arrows to set your workout incline, then press
ENTER PROGRAM. To start, press the START/STOP button.
10
PROGRAM MODE
•
Plug into a standard wall outlet (110-Volt AC, 15-amp circuit). Attach RED Safety Key to treadmill console.
•
Stand on the treadmill and straddle belt.
• Press POWER button. There will be an eight (8) second delay after pressing the POWER button before data can
be entered. The TIME window will flash.
•
There are three (3) pre-set programs on the 980S and 980HRS. Both include Fat Burn, Cardio, and Warm Up
programs. The 980HRS also includes a Heart Rate Control program (see the program profiles later in this
manual). Select the program by pressing the appropriate button.
•
Press START/STOP button. Belt will begin to move after 4 seconds. Step on belt slowly after the belt starts
moving.
• Each of the pre-set programs can also be customized. Follow the instructions below for your particular
model.
• 980S: Customizing programs in P1 and P2 Mode:
Each pre-set program can be customized in the P1 or P2
mode. The P1 and P2 modes allow you to save the information for future use. After making the program
selection with the MODE button, the CALORIES window will read “OP.” The ”OP” refers to “original program” and
is pre-set. Press the MODE button once more, and the CALORIE window will read P1. The “P1” mode is now
accessed. You can now program the Time and Incline in P1 mode, which will save your entered information for
future use. The time window will blink. Use the SPEED/TIME + or – arrows to select your workout time, then
press the ENTER PROGRAM button. The SPEED/TIME window will now be flashing. Using the same + or –
arrows, select the speed for your workout, then press ENTER PROGRAM. To start, press the START/STOP
button. To access P2 mode, press the MODE until the P2 shows in the CALORIE window for your selected
program. Follow the above procedure to customize.
• 980HRS: Customizing programs in P1 and P2 Mode: Each pre-set program can be customized in the P1 or P2
mode. After making the program selection, the center window will read “OP.” ”OP” refers to “original program”
and is preset. Press the same program button once more, and the center window will read P1. The “P1” mode is
now accessed. You can now program the Time, Speed, and Incline in P1 mode, which will save your entered
information for future use. The time window will blink. Use the SPEED/TIME + or – arrows to select your workout
time, then press the ENTER PROGRAM button. The SPEED/TIME window will now be flashing. Using the same
+ or – arrows, select the speed for your workout, then press ENTER PROGRAM. Now the INCLINE window will
be flashing. Use the INCLINE + or – arrows to set your workout incline, then press ENTER PROGRAM. To start,
press the START/STOP button. To access P2 mode, press the selected program button three times (once for
OP, twice for P1, three times for P2). Follow the above procedure to customize.
•
TO CHANGE A PREVIOUSLY PROGRAMMED P1, P2, or user program: Once you have programmed the P1
or P2 modes, you will need to use the PAUSE button to change the program you previously entered. For
instance, if P1 in Fat Burn has been programmed, to change to a new setting, press the Fat Burn button twice to
access P1. Then press the PAUSE button to get the TIME window to flash. Follow the directions above to
continue to change the program.
Program and Operating Instructions
11
Program and Operating Instructions
Heart Rate Control Instructions (980HRS only)
HEART RATE PROGRAM MODE
The Heart Rate program is designed to keep your heart rate a desired level of “beats per minute” by automatically
adjusting the incline. For example, if you have programmed in a desired heart rate of 105 beats per minute and your
heart rate is only 95 beats per minute (you must be wearing Heart Rate Transmitter), the incline will automatically
increase to intensify the work load, and increase you heart rate to the 105 beats per minute you programmed.
If your heart rate is above your programmed amount of beats per minute the incline will automatically decrease to
lower your heart rate. You may at any time during the Heart Rate Program adjust/override the speed and or incline
by simply pressing the correct corresponding buttons. You may change your “Target Heart Rate” at ant time during
the program by pressing the TARGET + or TARGET – buttons.
•
Plug into a standard wall outlet (110-Volt AC, 15-amp circuit). Attach Safety Key to console
• Place the Heart Rate transmitter strap across chest against the skin. Stand on the treadmill and straddle belt.
•
Press POWER button. There will be an eight (8) second delay after pressing the POWER button before data can
be entered. The TIME window will flash. The “Heart” shape on the treadmill will be flashing if the Heart Rate
Transmitter is transmitting. Adjust the strap on the chest until the console is picking up a signal.
• For Quick Start, press START/STOP button. Belt will begin to move after 4 seconds. Step on belt slowly after
the belt starts moving. Speed or incline may be adjusted by using the appropriate + (increase) or – (decrease)
buttons. Heart rate will read out in the Incline window.
• To select the Heart Rate Control program, press the “Heart Rate Control” button.
• The incline window will flash “125”, which is the default program target heart rate.
•
Adjust Target Heart Rate to desired level with the TARGET + or – buttons.
• Press START/STOP button, or continue instructions below to program Time, Speed and Incline.
• You can now program the Time, Speed, and Incline. The time window will blink. Use the SPEED/TIME + or –
arrows to select your workout time, then press the ENTER PROGRAM button. The SPEED/TIME window will
now be flashing. Using the same + or – arrows, select the maximum speed for your workout, then press ENTER
PROGRAM. Now the INCLINE window will be flashing. Use the INCLINE + or – arrows to set your maximum
workout incline, then press ENTER PROGRAM. To start, press the START/STOP button.
12
Program Profiles
13
Belt Adjustment and Tension
WARNING! Do not overtighten rollers! This will cause premature roller bearing failure!
Belt adjustment and tension performs two functions: adjustment for tension and centering. Your
new treadmill comes pre-adjusted from the factory for tension and centering. Please follow the
procedures below if the belt shifts left or right or if the belt slips while walking:
WALKING BELT HAS SHIFTING TO THE LEFT (Diagram 1)
First, unplug the power cord from the surge protector. Using the hex key provided, turn the left
rear roller adjustment bolt ¼ turn in the clockwise direction. Plug the power cord back into the
surge protector and run the treadmill at 2.5 mph. You should see the belt start to correct itself,
moving back towards the center. Repeat the above procedure until the walking belt is centered.
It may be necessary to set walking belt tension once you have completed this procedure if the belt
feels like it is slipping while walking. Refer to below to the “Walking Belt Slipping” instructions.
WALKING BELT HAS SHIFTING TO THE RIGHT (Diagram
2)
First, unplug the power cord from the surge protector. Using
the hex key provided, turn the right rear roller adjustment bolt
¼ turn in the clockwise direction. Plug the power cord back
into the surge protector and run the treadmill at 2.5 mph. You
should see the belt start to correct itself, moving back towards
the center. Repeat the above procedure until the walking belt
is centered. It may be necessary to set walking belt tension
once you have completed this procedure if the belt feels like it
is slipping while walking. Refer to below to the “Walking Belt
Slipping” instructions.
WALKING BELT IS SLIPPING DURING USE (Diagram 3)
First, unplug the power cord from the surge protector. Using
the hex key provided, turn both left and right rear roller
adjustment bolts the same distance, usually a ¼ turn in the
clockwise direction. Plug the power cord back into the surge
protector and run the treadmill at 2.5 mph. You should now
walk on the belt to determine if the belt is still slipping. Repeat
the above procedure until the walking belt is not slipping. The
tension should be just tight enough not to slip.
14
Change Miles per hour to Kilometers per hour
Your treadmill will operate in British Units (miles per hour) or International Units (kilometers per
hour). All treadmills are calibrated at the factory for British Units (miles per hour). To change the
display to read in kilometers, follow the steps described here:
1)Power is turned OFF on the console. Attach the magnet safety key to the console.
2) Activate the calibration mode switch by inserting the eraser end of a pencil into the opening in
the backside of the console (see diagram below).
3) Depressing the calibration mode switch TWICE and CL21 should appear in the TIME window.
(On the 980S and 980HRS, ‘mph or kph’ will be flashing in the SPEED window)
4) Pressing the the SPEED +/- button will activate choice, then press “ENTER PROGRAM.”
5)To accept the setting, press the POWER button.
15
Maintenance Instructions
WARNING! Before performing any maintenance to your treadmill, always unplug
the power cord from the surge protector.
CLEANING
Routine cleaning of your Keys Fitness treadmill will extend the life of your treadmill. WARNING! To prevent electrical
shock, be sure the power to the treadmill is OFF and the unit unplugged from the wall electrical outlet before
attempting any cleaning or maintenance.
AFTER EACH WORKOUT: Wipe off the console and other treadmill surfaces with a clean, water dampened soft
cloth to remove excess perspiration. USE NO CHEMICALS.
WEEKLY: Use of a treadmill mat is recommended for ease of cleaning. Dirt from your shoes contacts the belt and
eventually makes it to underneath the treadmill. Vacuum underneath treadmill once a week.
DECK LUBRICATION
The walking belt has been pre-lubricated at the factory. However, it is recommended that the walking board be
checked periodically for lubrication to ensure optimal treadmill performance.
Every 30 days or 30 hours of operation, lift the sides of the walking belt and feel the top surface of the walking board
as far under as you can reach. If you feel signs of silicone, no further lubrication is required. If it feels dry to the
touch, follow the instructions below.
Please use silicone such as “Napa 8300” (available at most stores).
TO APPLY LUBRICANT TO THE WALKING BOARD
1) Position the walking belt so that the seam is located on top and in the center of the center of the walking board.
2) Insert the spray nozzle into the spray head of the lubricant can.
3) While lifting the side of the walking belt, position the spray nozzle between the walking belt and the board
approximately 6” from the front of the treadmill. Apply the silicone spray to the walking board, moving from the front
of the treadmill to the rear. Repeat this on the other side of the belt. Spray approximately 4 seconds on each side.
4) Allow the silicone to ‘set’ for one minute before using the treadmill.
WARNING: Do not overlubricate the walking board. Excess lubricant should be wiped off with a clean towel.
16
Troubleshooting Guide
Treadmill will not start.
1) Is the RED Safety Key Attached to the Console?
2) Make sure the power cord is plugged into a surge protector, the surge protector is plugged into a
properly grounded outlet, and the surge protector is turned on. (Refer to “Power Requirements”)
3) Check the circuit breaker located on the front of the treadmill. If the switch protrudes, it has tripped.
Wait five minutes and then press the switch back in.
4) Check the house electrical breaker box and the circuit breaker for the room the treadmill is located in.
If it has tripped, reset or have an electrician replace the breaker in home.
5) Have an electrician check for inadequate voltage at the outlet.
Treadmill looses power during use.
1) Check the circuit breaker located on the front of the treadmill. If the switch protrudes, it has tripped.
Wait five minutes and then press the switch back in.
2) Check the house electrical breaker box and the circuit breaker for the room the treadmill is located in.
If it has tripped, reset or have an electrician replace the breaker in home.
3) If treadmill still will not operate, please call Keys Technical Service at (888) 340-0482.
Treadmill walking belt slows during use.
1) Check to make sure the treadmill is securely plugged into an UL-listed surge protector, rated at 15
amps, with a 14-guage cord of five feet or less and the surge protector is securely plugged into the
outlet.
2) If treadmill still will not operate, please call Keys Technical Service at (888) 340-0482.
Treadmill walking belt slips or is not centered on rear roller.
1) Refer to “Belt Adjustment and Tension” section.
2) Need help? Call Keys Technical Service at (888) 340-0482.
Treadmill Error Messages.
2)Your treadmill is equipped with a software package that enables error messages to be displayed when
there is a problem.
To avoid possible damage to the treadmill and the possibility of injury, do not
operate the treadmill until the problem is corrected. Call Keys Technical Service at (888) 340-
0482.
17
KEY # PART # DESCRIPTION QTY KEY # PART # DESCRIPTION QTY
1 UP 3K ASSB 4" UPRIGHT ASSEMBLY D. GRY 1 53 08-0004 CIRCUIT BREAKER 15 AMP 1
2 DECK ASSB DECK ASSEMBLY D GRY 1 54 08-0065 Membrane, center 4 window
3 ELEV ASSB ELEVATION ASSEMBLY D. GRY 1 55 11-0002 REAR ELEVATION BUSHING 2
56 11-0003 UPRIGHT PIVOT BUSHING 2
5 19-0010 UPRIGHT PIVOT BRACKET 2 57 1
6 19-0013 SAFETY LATCH 1 58 14-0069 END CAP DECAL 2
7 19-0014 MOTOR MOUNTING BRACKET 1 59 14-0145 CONSOLE DECAL 980S 1
8 19-0015 MOTOR COVER BRACKET 6 60 XX-0032 MOTOR COVER DECAL 980S 1
9 19-0029 OPTICAL WHEEL BRACKET 1 62 14-0024 SAFETY LATCH DECAL N/S 1
10 19-0019 BELT GUIDE 2 63 14-0025 WARNING FOLDING DECAL N/S 1
64 14-0026 WARNING CONSOLE DECAL N/S 1
12 19-0032 SPRING ANCHOR BRACKET 2 65 02-0078 MOTOR TENSION SPRING 1
13 06-0018 BASE PAN MOTOR 1 66 02-0002A DECK LIFT SPRING 4
67 02-0004 SCREW, 8X 5/8 PHIL PH 57
68 02-0005 SCREW, 8X 5/8 PHIL PH HILO 8
16 05-0007 SIDE BOARD EXTRUSION 2 69 02-0006 BOLT, 5/16 X 5 - 1/2 SHOULDER BOLT 1
17 06-0027 PIVOT SUPPORT COVER 2 70 02-0007 5/16-18 NYLOCK NUT 4
19 06-0003 PULLEY vx0086 8 GR not shown 1 71 02-0008 SCREW, 5/16-18 X 3/4 HEX 3
21 06-0073 3-PC LCD CENTER Plastic Console 4 wdw 1 72 02-0009 NUT, 5/16-18 WHIZLOC 3
22 06-0080 FAN 5" 8mm bore 1 76 02-0013 LOCK WASHER, 1/4 8
23 06-0020 BASE PAN END 1 77 02-0014 SCREW, 1/4-20 X 2 - 1/2 HEX 10
24 06-0004 BASE PLUG 2 78 02-0015 SPRING WASHER 4
25 06-0005 DOME PLUG 4 79 02-0016 SCREW, 3/8-16 X 2 - 1/2 HEX 1
26 06-0025 MOTOR COVER 1 80 02-0017 NUT, 3/8-16 NYLOCK 2
27 06-0008 END CAP 1 81 02-0018 PUSH NUT, 3/8 HAT 4
82 02-0019 CARRIAGE BOLT 10-24 X 1-1/2 4
29 06-0019 BASE PAN CENTER 1 83 02-0020 SCREW, 1/4-20 X 2-1/2 SOCKET HEAD 2
30 06-0011 2" ROLLER WHEEL 2 84 02-0021 WASHER, 9/32 X 5/8 X 1/8 3
31 06-0012 3” ROLLER WHEEL 2 85 02-0022 NUT, 10-24 NYLOCK 4
32 06-0013 UPRIGHT SPACE 2 87 02-0024 CARRIAGE BOLT 5/16 X 1 2
33 10-0004 RUBBER FOOT 3 88 02-0025 WHEEL AXLE 2
34 10-0002 BOARD ISOLATOR 8 89 02-0026 PUSH NUT 10
35 10-0005 FOAM GRIP 2 91 02-0028 SAFETY KEY 1
36 08-0077 FERRITE CORE 1 93 02-0030 SCREW, 8-32 X 5/8 HEX TRILOBE 1
37 12-0022 ACTUATOR (ELEVATION MOTOR) 1 94 02-0031 SCREW, 3/8-16 X 1 3/4 HEX 1
38 12-0016 DRIVE MOTOR 1
39 03-0003 WALKING BOARD 1
40 04-0008 WALKING BELT 18" X 105" 1 97 02-0034 SCREW, 8-32 X 5/8 PPH N/SHOWN 1
41 04-0004 POLY V BELT 1 98 02-0035 NUT, 8-32 NYLOCK NOT SHOWN 4
42 09-0012 FRONT ROLLER ASSEMBLY 1 99 02-0036 SCREW, GREEN HEAD 8 X 5/8 PPH 2
43 09-0013 REAR ROLLER 1 101 02-0038 HEX WRENCH 3/16 NOT SHOWN 1
44 13-0011 POWER CORD 1 1
45 13-0003 ENCODER HARNESS 1 1
46 14-0155 OVERLAY OPERATION 1 104 14-0027 EMERGENCY STOP DECAL 1
47 14-0156 OVERLAY CUP HOLDER 1 105 06-0014 BUSHING, STRAIN RELIEF 1
48 13-0016 CONTROL PANEL HARNESS 1 107 06-0016 WIRE TIES NOT SHOWN 10
49 13-0007 JUMPER WIRE 6" NOT SHOWN 1 108 06-0021 WIRE CLAMP NOT SHOWN 5
50 07-0027 UPPER LCD ELECTRONICS 1 109 06-0022 RESET GUIDE TUBE NOT SHOWN 1
51 08-0014 MOTOR CONTROLLER 1 110 06-0024 HEX WRENCH CLIP NOT SHOWN 1
52 08-0047 OPTICAL ENCODER 1 111 10-0007 6" CROSS HANDLEBAR FOAM GRIP 2
Parts List - 980S Treadmill
18
KEY # PART # DESCRIPTION QTY KEY # PART # DESCRIPTION QTY
1 UP 3K ASSB 4" UPRIGHT ASSEMBLY D. GRY 1 53 08-0004 CIRCUIT BREAKER 15 AMP 1
2 DECK ASSB DECK ASSEMBLY D GRY 1 54 13-0017 TELCO HARNESS FOR HEART RATE 1
3 ELEV ASSB ELEVATION ASSEMBLY D. GRY 1 55 11-0002 REAR ELEVATION BUSHING 2
4 SES EXT S.E.S. EXTENSION TUBE D. GRY 2 56 11-0003 UPRIGHT PIVOT BUSHING 2
5 19-0010 UPRIGHT PIVOT BRACKET 2
6 19-0013 SAFETY LATCH 1 58 14-0069 END CAP DECAL 2
7 19-0014 MOTOR MOUNTING BRACKET 1 59 14-0154 CONSOLE DECAL 980HRS 1
8 19-0015 MOTOR COVER BRACKET 6 60 XX-0036 MOTOR COVER DECAL 980HRS 1
9 19-0029 OPTICAL WHEEL BRACKET 1 62 14-0024 SAFETY LATCH DECAL N/S 1
10 19-0019 BELT GUIDE 2 63 14-0025 WARNING FOLDING DECAL N/S 1
64 14-0026 WARNING CONSOLE DECAL N/S 1
12 19-0032 SPRING ANCHOR BRACKET 2 65 02-0078 MOTOR TENSION SPRING 1
13 06-0018 BASE PAN MOTOR 1 66 02-0002A DECK LIFT SPRING 4
67 02-0004 SCREW, 8X 5/8 PHIL PH 57
68 02-0005 SCREW, 8X 5/8 PHIL PH HILO 8
16 05-0007 SIDE BOARD EXTRUSION 2 69 02-0006 BOLT, 5/16 X 5 - 1/2 SHOULDER BOLT 1
17 06-0027 PIVOT SUPPORT COVER 2 70 02-0007 5/16-18 NYLOCK NUT 4
19 07-0041 HEART RATE CHEST STRAP no t shown 1 71 02-0008 SCREW, 5/16-18 X 3/4 HEX 3
21 06-0053 3-PC LCD CENTER PLASTIC CONSOLE 1 72 02-0009 NUT, 5/16-18 WHIZLOC 3
22 06-0080 FAN 5" 8mm bore 1 76 02-0013 LOCK WASHER, 1/4 8
23 06-0020 BASE PAN END 1 77 02-0014 SCREW, 1/4-20 X 2 - 1/2 HEX 10
24 06-0004 BASE PLUG 2 78 02-0015 SPRING WASHER 4
25 06-0005 DOME PLUG 4 79 02-0016 SCREW, 3/8-16 X 2 - 1/2 HEX 1
26 06-0025 MOTOR COVER 1 80 02-0017 NUT, 3/8-16 NYLOCK 2
27 06-0008 END CAP 1 81 02-0018 PUSH NUT, 3/8 HAT 4
28 06-0009 S.E.S. EXTENSION GLIDE 4 82 02-0019 CARRIAGE BOLT 10-24 X 1-1/2 4
29 06-0019 BASE PAN CENTER 1 83 02-0020 SCREW, 1/4-20 X 2-1/2 SOCKET HEAD 2
30 06-0011 2" ROLLER WHEEL 2 84 02-0021 WASHER, 9/32 X 5/8 X 1/8 3
31 06-0012 3” ROLLER WHEEL 2 85 02-0022 NUT, 10-24 NYLOCK 4
32 06-0013 UPRIGHT SPACE 2 87 02-0024 CARRIAGE BOLT 5/16 X 1 2
33 10-0004 RUBBER FOOT 3 88 02-0025 WHEEL AXLE 2
34 10-0002 BOARD ISOLATOR 8 89 02-0026 PUSH NUT 10
35 10-0005 FOAM GRIP 2 91 02-0028 SAFETY KEY 1
36 07-0020 HEART RATE RECEIVER NOT SHOWN 1 93 02-0030 SCREW, 8-32 X 5/8 HEX TRILOBE 1
37 12-0022 ACTUATOR (ELEVATION MOTOR) 1 94 02-0031 SCREW, 3/8-16 X 1 3/4 HEX 1
38 12-0016 DRIVE MOTOR 1
39 03-0003 WALKING BOARD 1
40 04-0008 WALKING BELT 18" X 105" 1 97 02-0034 SCREW, 8-32 X 5/8 PPH N/SHOWN 1
41 04-0004 POLY V BELT 1 98 02-0035 NUT, 8-32 NYLOCK NOT SHOWN 4
42 09-0012 FRONT ROLLER ASSEMBLY 1 99 02-0036 SCREW, GREEN HEAD 8 X 5/8 PPH 2
43 09-0013 REAR ROLLER 1 101 08-0088 MEM, LED CUP PROGRAM 980HRS 1
44 13-0011 POWER CORD 1 102 08-0093 MEM, LCD POWER 980HRS 1
45 13-0003 ENCODER HARNESS 1 103 02-0040 GUIDE TUBE RETAINER NOT SHOWN 1
46 14-0144 OVERLAY POWER 980HRS 1 104 14-0027 EMERGENCY STOP DECAL 1
47 14-0147 OVERLAY PROGRAM 980HRS 1 105 06-0014 BUSHING, STRAIN RELIEF 1
48 13-0016 CONTROL PANEL HARNESS 1 107 06-0016 WIRE TIES NOT SHOWN 10
49 13-0007 JUMPER WIRE 6" NOT SHOWN 1 108 06-0021 WIRE CLAMP NOT SHOWN 5
50 07-0013 UPPER LCD ELECTRONICS 1 109 06-0022 RESET GUIDE TUBE NOT SHOWN 1
51 08-0014 MOTOR CONTROLLER 1 110 06-0024 HEX WRENCH CLIP NOT SHOWN 1
52 08-0047 OPTICAL ENCODER 1 111 10-0007 6" CROSS HANDLEBAR FOAM GRIP 2
Parts List - 980HRS
19
Exploded View
20
Exploded View
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22

Keys Fitness 980HRS User manual

Keys Fitness
Brand
Keys Fitness
Model
980HRS
Category
Treadmills
Type
User manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents