Monogram ZDIS15 Installation guide

Brand: Monogram

Model: ZDIS15

Category: Ice cube makers

Type: Installation guide

Installation

Instructions

Automatic Icemaker

ZDI15

ZDIS15

Design Guide with

Installation Instructions

Monogram:_

Installation Instructions

BEFORE YOU BEGIN

Read these instructions completely and

carefully.

• IMPORTANT- Save these instructions for

local inspector's use.

• IMPORTANT- Observe all governing codes

and ordinances.

• Note to Installer - Be sure to leave these

instructions with the Consumer.

• Note to Consumer - Keep these instructions

with your Owner's Manual for future reference.

WARNING:

This appliance must be properly grounded.

See "Power Supply", page 4.

AVERTISSEMENT :

Get appareil doit _tre correctement mis

la terre. Consulter _{Alimentation

_lectrique _, page 4.

If you received a damaged ice machine, you should

immediately contact your dealer or builder.

Proper installation is the responsibility of the installer.

Product failure due to improper installation is not

covered under the GEAppliance Warranty. See the

Owner's Manual for warranty information.

• Use this appliance only for its intended purpose.

Check with local utilities for electrical codes that apply

in your area. Local codes vary. Installation, electrical

connections and grounding must comply with

applicable codes. In the absence of local codes, the

ice machine should be installed in accordance with

National Electrical Code ANSl/NFPA 70-1990 or latest

edition.

For Monogram local service in your area, call

1.800.444.1845.

For Monogram Service in Canada, call

1.888.880.3030.

For Monogram Parts and Accessories, call

1.800.626.2002.

CONTENTS

Design Information

Models Available ..............................................................3

Cutout & Product Dimensions ........................................3

Optional Accessories ......................................................3

Tools and Materials Required ......................................3

Installation

Advance Planning ............................................................4

Power Supply ....................................................................4

Remove Packaging ..........................................................5

Adjust Height of Ice Machine ........................................5

Water Supply ....................................................................6

Connect the Drain ............................................................6

Connect Water Supply ....................................................7

Reverse Door Swing ....................................................7, 8

Accessories

ZIP75WW, ZIP75BB Kit for 3/4" thick panels ........9, 10

Design Information

MODELS AVAILABLE

ZDI15, ZDIS15

Available in black, white and stainless steel.

The ice machine may be installed below a countertop

or used free-standing.

CUTOUT & PRODUCT DIMENSIONS

34" min.

Adjustable

to 34-1/2"

Cutout dimensions shown allow for a full door swing.

When installing a 3/4"thick custom door panel,

additional clearances atthe sides may be required.

Frameless Cabinets:

• If installing between frameless cabinets, a 1/2" filler

strip or side panel may be required on the hinge side.

The filler strip will act as a spacer between the door

case and adjacent cabinet, and will prevent

interference with icemaker door swing. The width of

the opening must include filler or side panel thickness.

NOTE: The addition of a 3/4" thick front panel will result

in a front to back depth of 24-1/16."

23-5/16" to

14-13/16'

OPTIONAL ACCESSORIES

ZIP75WW White and ZIP75BB Black--For the

installation of a trimless 3/4" thick custom panel on

white and black models (not for stainless steel models).

A custom handle of your choice may be installed

onto the 3/4" panel. See installation instructions on

pages 9 and 10.

ZPK1--Drain Pump Kit. For use when a floor drain is

not available.

TOOLS AND MATERIALS REQUIRED

• 1/4" socket

• 3/4" adjustable wrench

•Level

• GE SmartConnectTM Refrigerator Tubing Kit or 1/4" O.D.

copper tubing, of sufficient length to reach the installation

Installation Instructions

ADVANCE PLANNING

CAUTION: Duetoexcessive

weight, TWO PEOPLEARE REQUIREDTO

MOVE AND INSTALL THIS ICE MACHINE.

MISE EN GARDE :

A cause de son poids elev&lL FAUT

DEUX PERSONNES POUR DEPLACERET

INSTALLERCEDISTRIBUTEUR DE GLACE.

Choose the location:

• The ice machine must be installed in an area

protected from elements such as wind, rain, water

spray or drip. The area should be ventilated with

temperatures above 55°F (13°C) and below 110°F

(43°C). Best results are obtained between 70°F (21°C)

and 90°F(32°C).

• The ice machine may be closed in on the top and

three sides as long as the front is unobstructed for

air circulation and proper operation.

-Installation should be such thatthe ice machine

can be moved forward for servicing, if necessary.

-The bottom grille on the front must be unobstructed

to provide proper air flow.

Before you begin:

1. If a custom panel is to be installed, follow the

instructions shown on pages 9 and 10.

-Order ZIP75 (black or white) panel kit.

-Order the custom panel from the cabinet

manufacturer.

-Secure the custom panel onto the ice machine.

2. Determine a method of drainage. If a floor drain is

to be installed, the drain must be accurately

located. The installation of a custom door panel will

affect the drain location. See page 6 to determine

the exact location of the floor drain, front to back,

with or without a custom door panel.

-A drain pump kit, ZPK1, is available and will not

interfere with placement of the ice machine.

3. The door swing is reversible. If desired, change the

door swing before installation.

4. Slide the ice machine into the installation location.

-Open and close the door to be sure there is no

interference.

-Check to be sure the ice machine can be

moved back into the opening, flush with adjacent

cabinetry. There should be no interference with

the floor drain.

POWER SUPPLY

IMPORTANT: (Please read carefully).

FORPERSONAL SAFETY,THIS APPLIANCE MUST BE

PROPERLYGROUNDED.

Do not use an extension cord or adapter plug with

this appliance. Follow National Electrical Code or

prevailing local codes and ordinances.

This ice machine must be supplied with 115V,60Hz,

and connected to an individual, properly grounded

branch circuit, and protected by a 15 or 20 amp circuit

breaker or time delay fuse.

Electrical Supply Should

Enter From Back Wall

InShaded Area.

• A properly grounded 3-prong receptacle should be

located within reach of the ice machine's 66" long

power cord. For a built-in installation, locate the

receptacle in the shaded area shown.

IMPORTANT: (Please read carefully).

The power cord of this appliance is

equipped with a three-prong

(grounding) plug that mates with

a standard three-prong grounding

wall receptacle to minimize the

possibility of electric shock. The

customer should have the wall receptacle and circuit

checked by a qualified electrician to make sure the

receptacle is properly grounded and has the correct

polarity.

• Where a standard two-prong wall receptacle is

encountered, it is the personal responsibility and

obligation of the customer to have it replaced with

a properly grounded three-prong wall receptacle.

Do not,under any circumstances, cut or remove

the third (ground) prongfrom the power cord.

DO NOT USEAN EXTENSION CORD.

Installation Instructions

REMOVE PACKAGING AND PARTS

• Laythe carton on rear face

and break open the bottom

flap.

• Setthe carton upright

with all four bottom flaps

outward.

• Lift carton up and off

icemaker.

• Remove all tape and

packaging material from the outside and inside

of the cabinet,

• Locate parts package with plastic plug buttons.

Set aside.

Open Bottom Flaps

ADJUST HEIGHT OF ICE MACHINE

Height adjustments may be necessary to install

the ice machine below a countertop, and may be

accomplished by adjusting both the front and rear

leveling legs,

ower

To adjust the height:

• With one person holding the ice machine, carefully

tilt the machine to access the leveling legs,

• Use an adjustable wrench to turn the legs.

-Turn legs right to lower, turn left to raise the

machine,

• Check top and side with a spirit level. Continue

adjusting legs until the ice machine is level

and stable.

Installation Instructions

WATER SUPPLY

• A cold water supply is required for icemaker

operation. The water pressure must be between

20 and 120 p,s.i.

Water Supply Should

Enter From Back Wall

In Shaded Area.

• Route GE SmartConnect TM Kit or 1/4" O.D. copper

tubing between house cold water line and the water

connection location.

• The water line should be long enough to extend

to the back of the ice machine. Allow enough to

accommodate moving unit forward for service.

NOTE:The only GEapproved plastic tubing is supplied

in the GE SmartConnectTM Refrigerator Tubing kits. Do

not use any other plastic water supply line because the

line is under pressure at all times. Other types of plastic

may crack or rupture with age and cause water

damage to your home. GE SmartConnecf MRefrigerator

Tubing Kits are available in the following lengths:

2'(0,6 m) WX08X10002

6'(1.8 m) WX08X10006

15' (4,6m) WX08X10015

25' (7.6m) WX08X10025

Shut off the main water supply

Turn on the nearest faucet long enough to clear the

line of water.

Install a shut-off valve between the ice machine

water valve and cold water pipe in a basement or

cabinet, The installation of an easily accessible

shut-off valve in the water line is required,

NOTE: Itis best to install the valve into a vertical

water pipe. If you install the valve into a horizontal

water pipe, make the connection atthe top or side,

rather than atthe bottom, to avoid drawing off any

sediment from the water pipe,

• Turn on the main water supply and flush debris

from the line. Run about a quart of water through

the tubing into a bucket, Shut off water supply at

the shut-off valve.

WATER SUPPLY (cont.)

NOTE: Saddle type shut-off valves are included in

many water supply kits, but are not recommended

for this application,

NOTE:Commonwealth of Massachusetts Plumbing

Codes 248CMRshall be adhered to. Saddle valves

are illegal and use is not permitted in Massachusetts.

Consultwith your licensed plumber.

• Install optional water filter in the water line near the

ice machine. A water filter is recommended in areas

where water supply contains sand or particles.

Installation instructions are packed with the filter.

CONNECT THE DRAIN

This ice machine is

equipped with a gravity

drain to prevent water

from flowing back into

the ice machine storage

bin and potentially

flowing onto the floor.

A floor drain is

acceptable, The ideal

installation has a

standpipe with a 2" to

1-1/2" PVCdrain reducer

installed directly below

Custom Panel

the outlet of the drain tube:

/Drain Hose

NOTE:A drain pump is necessary when a floor drain

is not available, Order ZPK1 Drain Pump Kit or contact

your local plumber for a recommended pump available

in your area.

TEST DRAIN HOSEALIGNMENT: Before sliding the ice

machine into the cabinet opening, check to be sure

the bottom of the drain tube is below the rear cover.

Totest, place a pan belowthe drain hose. Pour a

gallon of water into the ice bin and checkto be sure

that water does not wet the rear cover.

-7-1/2" to centerline _

of the opening,

3q/2"

-Approximately _j

3-1/2" high.

-22" from the front,

or 22-3/4"when _5,, _ 7-t/2"-_:L_

installing a 3/4" LocateStalldpipeinexact

Centerof TheCutout

door panel,

• Drain lines must be at least 5/8" inside diameter.

Installation Instructions

CONNECT WATER SUPPLY

• The water line should be flushed to clear any foreign

material before connecting to the icemaker.

• Connect the water line to the water supply tube

outside of the rear access cover.

Water

Supply

Line

CopperTubing:

• Use a standard plumbing female connector or union

for 1/4" copper tubing that can be purchased locally.

Coupling

(NotSupplied)

Nut

(Supplied)

Lineto

Icemaker

Ferrule

(NotSupplied)

Nut

(Supplied)

GE SmartConnectTM Tubing:

• Insert the molded end ofthe tubing into the icemaker

connection. _ghten the compression nut until it is

just hand tight.

• Tighten one additional turn with a wrench,

Overtightening can cause leaks!

• Make sure there are no sharp bends or kinks that

could restrict water flow.

• Slide the ice machine into its permanent location.

• To prevent

rattling, be sure

the copper tubing

does not touch

the side wall or

other parts inside

the cabinet.

• Open the shut-off

valve. Check for

leaks. -lighten

any connections

(including

connections

atthe valve)

if necessary.

Water Pan

Water Valve -

5-11/16" 4-5/8"

REVERSE THE DOOR SWING

IMPORTANT: Disconnect power to

the ice machine.

Tools Required:

• 1/4" and 5/16"wrench

• Flat putty knife

• Phillips screwdriver

Parts Supplied:

• 4 plug buttons

• 4 hinge screws

(on some models)

Parts Identification: (For Reference 0nly)

Hinge Pin Handle Screw

5/16" Hex Head Endcap Screw

Hinge Screw

• Remove the handle screws and lift off handle.

(On black and white models only.)

• Remove the hinge pin from the top hinge.

• Lift the door off of the bottom hinge. Place the hinge

pin back into the top hinge.

Reverse the door endcaps:

• Remove the screws and endcaps from the door,

top and bottom.

• Place the top endcap onto the bottom of the opposite

side of the door with the longflat side facing the

door front.

• Place the bottom endcap onto the top of the opposite

side of the door, with the longflat side facing the

door front.

• Setthe door aside.

Installation Instructions

REVERSE THE DOOR SWING (cont.)

Reverse the hinges:

• Using a flat putty knife, remove the screw hole plugs

opposite the door hinges, top and bottom. Set aside.

• Remove the two screws holding top hinge.

• Turn the hinge upside down, with the hinge pin

pointing up. Reinstall the hinge on the opposite side

at the bottom of the door.

• Remove the bottom hinge. Turn the hinge upside

down and install on the opposite side atthe top.

• Push screw hole plug buttons (supplied) into the

original screw holes.

• Remove the top hinge pin.

• Place plastic hinge sleeve on the bottom hinge and

position the door onto the pin.

• Place plastic hinge sleeve in the top hinge hole on

the door. Align the door on the bottom hinge and

replace top hinge pin.

• Reinstall handle with original screws.

Top Hinge _ HingePin

HingeSleeve/

DoorStop

BottomHinge

Hex Head Hinge Screw

, Hex Head

Hinge Screw

Sleeve/

_'-- Hinge Pin

Top

REVERSE THE DOOR SWING (cont.)

To reverse the door catch:

• Remove the plastic screws

from the opposite side

of the door.

• Remove the metal screws

from the magnetic door

catch and reinstall on the

opposite side of the door.

• Install the plastic screw

into place on the opposite

side of the door.

Reverse

Door Catch

Position

BottomHinge

Installation Instructions for ZIP75WW, ZIP75BB Kit

BEFORE YOU BEGIN

Read these instructions completely and

carefully.

• IMPORTANT- Save these instructions for

local inspector's use.

• IMPORTANT- Observe all governing codes

and ordinances.

• Note to Installer- Be sure to leave these

instructions with the Consumer.

• Note to Consumer - Keep these instructions with

your Owner's Manual for future reference.

WARNING:

To prevent electric shock, disconnect

electrical power supply to ice machine

before installing front panel. Do not operate

ice machine while installing panel.

AVERTISSEMENT :

Pour _viter les chocs _lectriques, il faut

debrancher I'alimentation du distibuteur

de glace avant d'installer le panneau avant.

Le distributeur de glace ne dolt pas _tre

en marche pendant I'installation du

panneau avant.

Kit Contents:

• 2 side trim pieces

• 8 side trim screws

• Door handle

Tools and Materials Required:

• 8 flat head wood screws, 1/2" long

• Drill and 1/8" bit

• Safety glasses

• Tape

• Custom panel

NOTE: If installing a 3/4" trimless custom panel, a

3/4"wide filler strip or side panel may be required.

The filler strip will act as a spacer between the

icemaker case and the adjacent cabinet, and will

prevent interference with the icemaker door swing.

The width of the cutout opening must include the

additional width of the filler panels.

This kit contains a new handle and 2 side mounting

brackets to support a trimless custom door panel

up to 3/4"thick. A custom handle may replace the

supplied handle.

IMPORTANT:

• Cut edges of the custom door panel will be seen and

must be finished for best appearance. The back side

of the panel should be finished a minimum of 1/2"

on all sides.

• The custom panel, both raised and flat design,

should be constructed in the same manner as typical

cabinet doors.

• Order the custom panel from the cabinet manufacturer.

Be sure to provide the exact dimensions so that the

panel is constructed accurately.

29-1/2" I

Left Trim

Custom

Panel

14_23/32"

Right Trim

Installation Instructions for ZIP75WW, ZIP75BB Kit

I STEP 1 DISCONNECT POWER I

TO THE ICE MACHINE

STEP 2 REMOVE HANDLE

AND NAMEPLATE

• Remove the door handle by removing the two top

mounting screws. Set screws aside, Discard handle.

• The Monogram nameplate is held in place with

adhesive. Remove the nameplate.

STEP 3 MARK MOUNTING

SCREW LOCATIONS

• Align and hold the side trim pieces againstthe ice

machine door and mark screw locations on the sides.

• Drill 1/8" pilot holes into the door sides of the ice

machine.

STEP 4 SECURE CUSTOM HANDLE

TO CUSTOM PANEL.

(SKIP THIS STEP IF

YOU ARE USING THE

SUPPLIED HANDLE)

A custom handle can be installed onto the 3/4"thick

panel, replacing the supplied handle.

• The custom handle can be installed atthe top or side

of the panel.

• Drill pilot holes through the front of the custom panel

to match the chosen handle.

• Secure the handle to the panel with flat head wood

screws.

• Replace original handle screws in the top of the door

frame,

STEP 5 SECURE SIDE TRIM PIECES

TO CUSTOM PANEL

• Lay the custom panel appearance-side-down

on a clean surface.

• Align top and bottom side trim to the custom

panel sides.

• Tape the side trim pieces to the back of the

custom panel,

• Place the panel with trim against the door to be sure

that trim and panel fits the door side to side and top

to bottom. Adjust as needed.

• Mark screw locations and remove trim.

Drill pilot holes.

• Install side trim to the back side of the custom

panel with screws (not supplied). Use flat head

wood screws approximately 1/2" long,

STEP 6 INSTALL ASSEMBLED PANEL

ONTO THE ICE MACHINE

• Install panel to ice machine with supplied screws,

4 on each side.

STEP 7 INSTALL SUPPLIED DOOR

HANDLE (IF USED)

• Install the new supplied handle with original screws.

Notes

Pub.No.49-60016-3 ]

PartNo.197D2522PO01

2217279Rev.1 02-04JR

Printedinthe UnitedStates

NOTE:While performing installations described inthis book,

safety glasses or goggles should be worn.

o 6)

For Monog'ram local service i)_ )our (m_a, c(dl

1.600.4dd. l,_4).

NOTE: t ro(lucl improv(_m(_m is a comimfillg (md(_avor

al G( neral El(_ctri(. Th(r(for(_, malerials, appearan(:(

and sp(_(ifi(alions ar(_ sul_je(:t to (h_mg¢ wilholll noli((.

Monogram;

GEConsumer & Industrial

Louisville, KY40225

@2004GE Company

Monogram ZDIS15 Installation guide

Brand: Monogram

Model: ZDIS15

Category: Ice cube makers

Type: Installation guide

Download PDF

report

Monogram ZDIS15 Installation guide

Monogram ZDIS15 Installation guide

Related papers

Other documents