Snapper 13037130 Owner's manual

Brand: Snapper

Model: 13037130

Category: Lawnmowers

Type: Owner's manual

Operator's Manual

Model No. Description

78007O7

7800708

7800756

7800757

SPXV2270

SPXV2270E

NSPXV2270

NSPXV2270E

Manual No. 7104292 (Rev.'-')

Thank You for purchasing this quality-built Snapper mower. We're pleased that you placed your

confidence in the Snapper brand. When operated and maintained according to the instructions in this

manual, your Snapper mower will provide many years of dependable service.

This manual contains safety information to make you aware of the hazards and risks associated with

the machine and how to avoid them. This machine is designed and intended only for finish cutting of

established lawns and is not intended for any other purpose. It is important that you read and understand

these instructions thoroughly before attempting to start or operate this equipment. Save these original

instructions for future reference.

Dateof Purchase

Retailer

Retailer's Phone Number

Equipment

Model Number

Serial Number

Engine

Model .Type Code

SNAPPERis a trademark of

Briggs & Stratton PowerProducts Group, LLC

Milwaukee, WI, USA.

Tableof Contents

OperatorSafety ................................................................................... 4

Safetyinstructions......................................................................................................................4

SafetyandOperationDecals.......................................................................................................6

Featuresand Controls............................................................................ 8

AssembJy........................................................................................... 9

Operation.......................................................................................... 10

BeforeStarting..........................................................................................................................10

FuelRecommendations.............................................................................................................10

StartingtheMower...................................................................................................................11

PropellingtheMower...............................................................................................................11

HandleHeightAdjustment........................................................................................................11

CuttingHeightAdjustment........................................................................................................12

MulchingOperation..................................................................................................................12

installingtheDischargeDeflector.............................................................................................12

installingtheGrassBag............................................................................................................13

ChargingtheBattery.................................................................................................................14

MaintenanceReminder.............................................................................................................15

Maintenance ...................................................................................... 16

MaintenanceChart....................................................................................................................16

ChangeEngineOil....................................................................................................................17

ServiceAir Filter.......................................................................................................................17

CheckSafetyInterlockSystem..................................................................................................18

CleanDebrisOffMower............................................................................................................18

DriveControlAdjustment.........................................................................................................19

StorageProcedure....................................................................................................................19

Troubleshooting .................................................................................. 20

Warranties ........................................................................................ 21

Slope Guide....................................................................................... 23

WARNING

It is a violation of California Public ResourceCode,Section

4442, to use or operatethe engine on any forest-covered,

brush-covered, or grass-coveredland unless the exhaust

system is equippedwith a spark attester, as defined in

Section 4442, maintained in effectiveworking order. Other

states or federal jurisdictions may havesimilar laws.

Contactthe original equipment manufacturer, retailer, or

dealer to obtain a spark arrester designed for the exhaust

system installed on this engine.

WARNING

Batteryposts, terminals and relatedaccessoriescontain

lead and lead compounds, chemicals known to the State

of California to cause cancer and birth defects or other

reproductive harm. Wash hands after handling.

WARNING

Engineexhaust, some of its constituents, and certain

vehicle components contain or emit chemicals known to

the State of California to causecancer or other reproductive

harm.

OperatorSafety

,L_ WARNING:This powerful cutting machine is capableof amputating handsand feet and canthrow objects

that can cause injury and damage! Failureto comply with the following SAFETYinstructions could result in

serious injury or deathto the operator or other persons.Theowner of the machine must understand these

instructions and must allow only persons who understandthese instructions to operate machine.Each

personoperating the machine must be of sound mind and body and must not be under the influence of any

substance,which might impair vision, dexterity or judgment. If you haveany questions pertaining to your

machinewhich your dealer cannot answer to your satisfaction, contact Customer Service (1-800-317-7833

or www.snapper.com).

PROTECTION FOR CHILDREN

Tragic accidents canoccur if the operator is not alert to

the presenceof children. Children are often attracted to

the machineand the mowing activity. Never assumethat

children will remain whereyou lastsaw them.

1. KEEPchildren out of the mowing area and under the

watchful careof a responsible adult other than the operator.

2. DONOTallow children in yard when machine is operated

andturn machine OFFifanyoneenters the area.

3. DONOTallow pre-teenagechildren to operate machine.

4.ALLOW only responsible adults & teenagerswith mature

judgment underclose adult supervision to operate machine.

5. DONOTpull mower backwards unless absolutely

necessary.LOOKand SEEbehind and down for children,

pets and hazards beforeand while backing.

6. USEEXTRACAREwhen approaching blind corners,

shrubs, trees, or other objects that may obscure vision.

SLOPEOPERATION

1. Slopesare a major factor relatedto slip and fall

accidents,which can result in severeinjury. All slopes

require extra caution. If you feel uneasyon a slope, DONOT

mow it.

2. Mow across slopes, neverup-and-down. Exercise

extremeCAUTIONwhen changing directions on slopes. DO

NOTmow steep slopes or other areaswhere stability or

traction is in doubt. Referto the Slope Guideat the back of

this manual.

3. Useextra carewith grass catchers or other attachments;

these affect the handling and the stability of the machine.

PREPARATION

1. Read,understand, and follow instructions and warnings

inthis manualand on the mower, engineand attachments.

Knowthe controls and the proper useof the mower before

starting.

2. Only mature, responsible persons shall operatethe

machine and only after proper instruction.

3. Data indicatesthat operators age 60 and above,are

involved in a large percentageof mower-related injuries.

Theseoperators should evaluatetheir ability to operatethe

mower safely enough to protect themselvesand others

from serious injury.

4. Handlefuel with extra care. Fuelsareflammable and

vapors are explosive. Useonly an approvedfuel container.

DONOTremovefuel capor add fuel with engine running.

PREPARATION

(Continued FromPrevious Column)

Add fuel outdoors only with enginestopped and cool. Clean

spilled fuel and oil from machine. DONOTsmoke.

5. Checkthe areato be mowed and removeall objects such

as toys, wire, rocks, limbs and other objects that could

cause injury if thrown by bladeor interferewith mowing.

Also notethe location of holes,stumps, and other possible

hazards.

6. Keeppeople and pets out of the mowing area.

Immediately, STOPBlade,Stop engine and Stop mower if

anyone enters the area.

7. Checkshields, deflectors, switches, blade controls and

other safety devicesfrequently for proper operation and

location.

8. Make sureall safetydecals are clearly legible. Replaceif

damaged.

9. Protectyourself when mowing and wear safety glasses,

long pants and substantial footwear. DONOTmow

barefootedor with sandals.

10. Know how to STOPbladeand engine quickly in

preparationfor emergencies.

11. Use extra carewhen loading or unloadingthe machine

into a trailer or truck.

12. Checkgrass catchercomponents frequently for signs of

wear or deterioration and replaceas neededto prevent inju-

ry from thrown objects going through weak or torn spots.

SAFEHANDLINGOFGASOLINE

To avoid personal injury or property damage,use extreme

care in handling gasoline. Gasolineis extremely flammable

and the vapors are explosive.

1. Extinguish all cigarettes, cigars, pipes and other sources

of ignition.

2. Use only an approvedfuel container.

3. DONOTremovefuel cap or add fuel with the engine

running. Allow the engineto cool before refueling.

4. DONOTrefuelthe machine indoors.

5. DONOTstore the machineor fuel container inside where

there is an open flame, spark or pilot light such as on a

water heateror other appliances.

6. DONOTfiii fuel containers inside a vehicle or on a

truck or trailer bed with a plastic liner. Always placethe

containers on the ground away from the vehicle before

filling.

4 www.snapper.com

OperatorSafety

SAFE HANDLING OF GASOLINE

(ContinuedFromPreviousPage)

7. Removegas-poweredequipment from the vehicle or

trailer and refuelit on the ground. If this is not possible,

then refuelequipment using a portablecontainer, rather

than a gasolinedispenser nozzle.

8. DONOTstart gas poweredequipment in enclosed

vehicles or trailers.

9. Keepthe nozzlein contact with the rim of the fuel tank or

container opening at all times until fueling is complete. DO

NOTusea nozzle lock-open device

10. If fuel is spilled on clothing, change clothing

immediately.

11. DONOToverfill a fuel tank. Replacefuel cap and tighten

securely.

OPERATION

1. DONOTput handsor feet near or under rotating parts.

Keepclearof discharge areawhile engine is running.

2. STOPenginewhen crossing gravel drives, walks, or

roads, and under anyconditions where thrown objects

might be a hazard.

3. Mow only in daylight or good artificial light.

4. DONOToperatemower while underthe influence of

alcohol or drugs.

5.After striking a foreign object or if mower vibrates

abnormally, STOPthe engine,disconnect and securespark

plug wire. inspect the mower for anydamageand repair the

damagebeforestarting.

6. DONOTmow near drop otis, ditches or embankments.

Operatorcould lose footing or balance.

7. STAYALERTfor holesand other hidden hazards.Tail

grass can hide obstacles. Keepawayfrom ditches,wash-

outs, culverts, fences and protruding objects.

8. DONOTmow on wet grass. Always be sure of your

footing. Keepa firm hold on the handleand walk, neverrun.

Slipping could cause injury.

9.ALWAYSstay behind handlewhen engine (motor) is

running.

10. DONOTleavethe machinewith the engine run-

ning. STOPBLADEand STOPENGINEbefore leavingthe

operators position for any reason.

11. Beforecleaning, repairing or inspecting make cer-

tain engine,blade and all moving parts haveSTOPPED.

Disconnectand secure spark plugwire awayfrom plug to

prevent accidentalstarting.

12. STOPengineand wait until the bladecomes to

completeSTOPbeforeremoving grass bagand/or clearing

grass.

13. DONOToperatemower without the entire grass

catcher, rear guard, or other safety devices in placeand

working. DONOTpoint discharge at people, passing cars,

windows or doors.

OPERATION

(ContinuedFromPreviousColumn)

14. DONOTdischarge material against a wail or

obstruction. Material may ricochet back towards the

operator.

15. Slow down beforeturning.

16. Watchout for traffic when near or crossing roadways.

17. DONOToperateengine in enclosedareas. Engine

exhaust gasescontain carbon monoxide, a deadly poison.

18. Onlyuse accessoriesapprovedby the manufacturer.

See manufacturer's instructions for proper operation and

installation of accessories.

MAINTENANCE AND STORAGE

1. DONOTstore mower or fuel container inside where

fumes may reachan openflame, spark or pilot light such

as in a water heater,furnace, clothes dryer or other gas

appliance. Allow engine to cool before storing machine in

an enclosure.Store fuel container out of reachof children

in awell ventilated, unoccupied building.

2. Keepmower and engine free of grass, leavesor excess

greaseto reducefire hazardand engine overheating.

3. Whendraining fuel tank, drain fuel into an approved

container outdoors and away from openflame.

4. Keepall bolts, especially bladebolts, nuts and screws

properly tight. Checkthat all cotter pins are in proper

position.

5. Alwaysprovide adequateventilation when running

engine. Engineexhaust gasescontain carbon monoxide, a

deadly poison.

6. Serviceengine and makeadjustments only when engine

is stopped. Removedspark plug wire from spark plug and

secure wire awayfrom spark plugto prevent accidental

starting.

7. DONOTchangeengine governor speedsettings or

overspeed engine.

8. Checkgrass bag assembly frequently for wear or dete-

rioration to avoid thrown objects and exposureto moving

parts. Replacewith new bagif loose seamsor tears are evi-

dent. Replaceslider or bagadapter if brokenor cracked.

9. Mower bladesare sharp and can cut. Wrap the bladesor

wear heavy leathergloves and useCAUTIONwhen handling

them.

10. DONOTtest for spark by grounding spark plug next to

spark plug hole; spark plug could ignite gas exiting engine.

11. Havemachine serviced by an authorized dealerat least

once a year and havethe dealer install any newsafety

devices.

12. Use only factory authorized replacementparts or like

parts when making repairs.

OperatorSafety

Safety andOperationDecals

Readingthis manual andthe safety instructions it contains

will provide the basic knowledge necessaryto operatethis

mower safelyand effectively. However,severalsafety and

operation decals havealso been placedon the mower as

a reminderof this important information during operation.

Thedecals noted below are located on the mower. Thesafety

warnings and operation instructions they contain should

be carefully read,understood, and followed. Not following

theseimportantwarningsand instructionscan resultin

seriousbodilyinjuryor death.

If any of these decals are lost or damaged, replacethem

immediately. Contactyour dealer for replacementdecals.

Mower Start

PartNo. 7104747

Mower Run

Part No. 7104745

Mower Stop

Part No. 7104746

SafetyWarnings

Part No. 7101394

DriveControl

PartNo. 7104744

KeepHandsand FeetAway

Part No. 7013010

6 www.snapper.com

Explanationof Safety Decals

OperatorSafety

A. WARNING:Avoid Serious injury or Death

Readthe operator's manualbefore attempting to

operatethe mower.

Mow across slopes, not up or down.

To avoid injury to others, do not mow when

others, especiallychildren, are around.

To reducethe potential for fire, wait at least2

minutes before refueling.

B. DANGER:Amputation and Thrown Object Hazard.

To avoid serious injury or death, keep handsand

feet away from the mower deck at all times during

operation.

_ To avoid injury from thrown objects, do not

"-?::i:_":_operatethe mower unless all mulching, discharge,

or bagging components are in their proper place.

C. DANGER:Keep Handsand FeetAway.

D. WARNING:Guardor EntireGrass CatcherMust Be

installed BeforeOperating Mower.

Explanationof Operation Decals

7,04747_

A. Drive Control

• Pushdrive control forward to propel mower. Pushthe

drive control further forward to increaseground speed.

B. Mower Start

1. Squeezeblade control against drive control, and pull

drive control aiithe way back.

2. Turn ignition key (SPXV2270E,NSPXV2270E)or pull

starter rope handleto start mower.

C. Mower Run

• Squeezebladecontrol against drive control.

D. Mower Stop

• Releasebladecontrol.

• Enginewill stop.

Featuresand Controls

IMPORTANT

Thefigures and illustrationsin this manualare provided

for referenceonly and may differ from your specific model.

Contactyour dealer if you havequestions.

Oil Fill Capand Dipstick F.

FuelFillerCap G.

Mulching Cover H.

Cutting Height Adjust Lever I.

BatteryChargePort (SPXV2270E, J.

NSPXV2270E)

BladeControl (2)

Drive Control (2)

ignition Switch (SPXV2270E,NSPXV2270E)

Starter RopeHandle

MaintenanceReminder

8 www.snapper.corn

Unpackthe

Mower

Cut all four corners of the box from top to bottom.

Removeaii packingmaterials from the mower.

Locate and identify the items included with the mower:

• Mulching plug (A, Figure 1 - installed)

• Grassbag (B)

• Battery charger(C - SPXV2270E,NSPXV2270E)

• Sidedischarge deflector (D)

• Operator's manual (E)

Assembly

Figure2:Raisingthehandleassembly

Figure1:Itemsincluded

Raisethe HandleAssembly

1. Loosen, but do not remove,the knobs (A, Figure 2) on

both sides of the upper handle.

2. Unfold the upper handleso that it is aligned with the

lower handle,and tighten the upper knobs.

3. Removethe handle knobs, washers and carriagebolts

from the lower handle (B).

4. Raisethe lower handle,aligning it with one of the three

sets of holes in the handle bracket. (Most userswill pre-

fer the middle position). Replacethe hardware removed

in Step3, tightening securely.

Set Upthe Starter RopeHandle

1. Squeezethe bladecontrol (A, Figure 3) against the

drive control (B).

NOTE.The blade control and drive control can be operated

from either side.

2. Pull the starter rope handle(C) out of the engine to the

rope guide (D). Hook the starter rope into the rope guide

(it might be a tight fit).

Figure3.Starterropehandle

Operation

BeforeStarting

1. Checkthe guards, deflectors, grass bag,and coversto

make sure all are in placeand securelytightened.

2. Checkthe blade control (A, Figure 4) and drive control

(B) to insure they work freely.

Figure4:Mowercontrols

Checkthe cutting height. Adjust to the desiredheight.

Refer to the section entitled 'Cutting Height Adjustment'.

Checkthe engine oil:

• Makesure the mower is on a level surface.

• Cleanthe oil fill areaof anydebris.

• Removethe dipstick (A, Figure 5) and wipe with a

cleancloth.

• insert andtighten the dipstick.

• Removethe dipstick and checkthe oil level. It should

be at the top of the full indicator (B) on the dipstick.

• If low, add oil (Briggs & Stratton warranty-certified

SAE30lawnmower oil is recommended) slowly into the

engine oil fill. Do notoverfill. After adding oil, wait one

minute and recheckthe oil level.

• Replaceandtighten the dipstick.

5. Add fuel to the tank:

• Makesure the mower is outside, where fumes can

safely dissipate.

• Removethe fuel fill cap (C, Figure 5).

• Fill the tankwith fuel. Referto the section entitled 'Fuel

Recommendations'.To allow for expansionof the fuel,

do not fill abovethe bottom of the filler neck(B).

• Reinstallthefuel fill cap.

6. Cleanthe exterior surfaces of the cutting deck and

engine of any accumulation of spilled fuel, dirt, grass,

oil, etc. Keepthe engine air intakescreen and cooling

fins clear at all times.

7. Chargethe battery. Refer to the section entitled

"Charging the Battery".

FuelRecommendations

Fuel mustmeet these requirements:

• Clean,fresh, unleadedgasolinewith

• A minimum of 87 octane / 87AKI (90 RON).

• Gasolinewith up to 10% ethanol (gasahol) or up to 15%

MTBE(methyl tertiary butyl ether) is acceptable.

• CAUTION:DONOTuse unapprovedgasoline, such as E85.

Do not mix oil in gasoline or modify the engineto run on

alternative fuels. This wiii damagethe engine components

and voidthe engine warranty.

Theengine on this equipment is certified to operateon

gasoline. Theemissions control systemfor this engine is EM

(Engine Modifications).

High Altitude

At altitudes over 5,000 feet (1524 meters), a minimum 85

octane/85AKi (89 RON)gasoline is acceptable.To remain

emissions compliant, high altitude adjustment is required.

Operationwithout this adjustment will cause decreased

performance, increasedfuel consumption, and increased

emissions.

Operationof the engineat altitudes below 2,500 feet (762

meters) with the high altitude kit is not recommended.

IMPORTANT

Thefigures andillustrations in this manualare provided

for referenceonly and may differ from your specific model.

Contactyour dealer if you havequestions.

Figure5:0il andfuelfill

iMPORTANTMower isshippedwithoutoil in engine.

Failure to add oil beforestartingwill result in engine

damage.

10 www.snapper.com

Starting the Mower

Theengine on this mower is equipped with aReadyStart®

system, which featuresa temperature-controlled automatic

choke, it does not havea manual choke or a primer.

1. Squeezethe bladecontrol (A, Figure 6) against the

drive control (B).

2. Pull the drive control all the way backto the neutral

position.

NOTEThe blade control and drive control can be operated

from either side.

3. Turn the ignition key (C, SPXV2270E,NSPXV2270E)or

pull the rope start handle (D) to start the engine.

4. To stop the engine (and blade), releasethe blade

control.

5. After the engine starts, allow a brief warm-up until the

engine runs smooth before beginning mower operation.

Figure6.Startingthemower

PropellingtheMower

1. Start the engine.

2. Begin slowly pushing the drive control (A, Figure 7)

forward to propel the mower. Forward speedcan be

increased by pushing the drive control further forward.

NOTEThe drive control canbe operatedfrom either side.

IMPORTANT:Upon initial use, the drive control may have

to be adjusted. Referto the section entitled "Drive Control

Adjustment".

Figure7:Prope//ingthemower

WARNING

To prevent unauthorized starting, always removethe

ignition key when leavingthe mower unattended.

HandleHeight Adjustment

Operation

WARNING

DONOTattempt any maintenance,adjustmentsor service

with engine and blade running. STOPengine and blade.

Removestarter insert. Disconnectspark plug wire and

secure awayfrom spark plug. Engineand components

are HOT.Avoid serious burns, allow sufficient time for all

components to cool.

Forgreater operator comfort, the height of the mower handle

can be adjusted.

1. Removethe handle knobs, washersand carriagebolts

from the lower handle (A, Figure 8).

NOTE:Donot removethe lower set of handle hardware(C).

2. Align the handle assemblywith one of the three handle

height adjustment holes (B).

3. Replacethe hardware removed in Step 1, tightening

securely.

Stoppingthe Mower

1. Stop forward motion of the mower by pulling the drive

control all the way back.

2. Stop the engine and blade by releasingthe blade

control.

3. Removethe ignition key from the control console

(SPXV2270E,NSPXV2270E).

Figure8:Adjustingthehand/eheight

Operation

Cutting HeightAdjustment

WARNING ,A

DONOTattempt any maintenance,adjustments or service

with engine and blade running. STOPengine and blade.

Removestarter insert. Disconnectspark plug wire and

secure awayfrom spark plug. Engine and components

are HOT.Avoid serious burns, allow sufficient time for all

components to cool.

Pull the cutting height adjust lever(A, Figure 9)

outward, and move to the desiredcutting height. The

highest cutting position is Notch 9, and the lowest

cutting position is Notch 1 (Figure 10). The leverwill

set all wheels to the samecutting height.

1.25 in 4.00 in

Figure10:Cuttingheightsettings(approximate)

Installingthe DischargeDeflector

WARNING

DONOTattempt any maintenance,adjustmentsor service

with engine and blade running. STOPengine and blade.

Removestarter insert. Disconnectspark plug wire and

secure awayfrom spark plug. Engineand components

are HOT.Avoid serious burns, allow sufficient time for all

components to cool.

1. Raisethe mulching cover (A, Figure 11).

2. Install the deflector (B) to the deck under the mulching

cover, making sure that the locking tabs on the deck (C)

go through the slots in the deflector (B).

3. Lowerthe mulching cover against the deflector.

Figure9:Adjustingcuttingheight

Mulching Operation

For best mulching results, cut up to a maximum of 1/3 of

grass length and recycle ONLYwhen grass is dry.

1. Make sure the discharge deflector and grass bag are

removed, and the mulching plug is installed.

2. Setthe cutting height adjust lever in the highest cutting

position (Notch 9).

3. Proceedmowing slowly. Graduallylower the cutting

height to obtain the best combination of cutting and

mulching performance.Cutting too much grass in one

pass, or cutting wet heavygrass maycause clumping or

plugging of the mower deck.

Figure11:Insta//ingthedischargedeflector

12 www.snapper.corn

Operation

nstallingthe GrassBag

WARNING ,A

DONOTattempt any maintenance,adjustments or service

with engine and blade running. STOPengine and blade.

Removestarter insert.Disconnectspark plugwire and

secure awayfrom spark plug. Engine and components

are HOT.Avoid serious burns, allow sufficient time for all

components to cool.

Important: Themulching plug must be removed only

when bagging is desired, and must be replacedas soon as

bagging operations are completed.

1. Raisethe rear discharge door (A, Figure 12).

2. Removethe mulching plug (B) from the rear discharge

chute.

Figure12:Removingthemu/chingp/ug

Figure13:Insta//ingthegrassbag

Holding the grass bag handle (A, Figure 13), install the

grass bag onto the mower, making sure that the grass

bag hooks (B) are hookedonto the rear door pivot rod

(c),

WARNING

Grass Catcherbags are madeof woven fabric, and are

subject to deterioration and wear during normal usage.

Checkcondition of bag beforeeach use. immediately

replaceworn or damagedcatcher bagswith only bags

recommended bythe manufacturer. The grass catcher

is optional equipment on some models.

Chargingthe Battery

The batteryin this mower is sealedand maintenancefree,

and requiresno serviceother than charging. If the battery

will not accepta charge, bring the mower to an authorized

servicecenter for service.

1. Using the supplied charger, plug the charger connec-

tor into the battery chargeport (A, Figure14). Plug

the charger into awall outlet and chargethe battery

for 12-24 hours. (Longer periods will not damagethe

battery.)

Important: Use only the charger supplied with the mower to

chargethe battery. Using a different charger may damage

the battery and/or mower.

2. Whencharging is complete, unplug and store the

charger.

Operation

Figure14:Batterychargeport

eep allsparks, flame and fire awayfrom

I chargingthe battery.Neveruse "BOOST"£ g2;

Ithe battery.

14 www.snapper.com

Operalion

Mainlenance Reminder

The maintenancereminder (A, Figure15) provides timely

reminders of important maintenanceitems. It has six

display modes:

Total Hours

Displays total hours mower hasbeen operated.This is the

default screen.

Trip Hours

To display:

Press the 'Mode' button (B) until the 'Trip Hours' screen

is displayed.

To reset:

Press and hold the 'Reset' button (C) for more than 3

seconds.

Clock

To display:

Press the 'Mode' button until the 'Clock' screen is

displayed.

To set:

1. Pressand hold the 'Mode' button for more than 3

seconds. Thehour display will flash.

2. Pressthe 'Reset' button to setthe correct hour.

3. Press

flash.

4. Press

5. Press

seconds

the 'Mode' button. The minutes displaywill

the 'Reset' button to set the correct minutes.

and hold the 'Mode' button for more than 3

to savethe set time.

Change Oil

The 'ChangeOil' icon (D) will appear after the first 5 hours

(total hours) of operation, then after every25 hours of oper-

ation thereafter. This indicates it is time to changethe oil. Be

sure to follow the proceduresoutlined in this manual.

To reset:

1. Pressthe 'Mode' button until the 'ChangeOil' screen

is displayed. (The iconwill flash.)

2. Pressand hold the 'Reset' button for more than 3

seconds.

Spark Plug

The'Spark Plug' icon (E) will appear every 50 hours (total

hours) of operation. This indicates it is time to changethe

spark plug. Be sureto follow the proceduresoutlined in this

manual.

To reset:

1. Pressthe 'Mode' button until the 'Spark Plug' screen

is displayed. (The icon will flash.)

2. Pressand hold the 'Reset' button for more than 3

seconds.

NOTE:if not reset,the 'Spark Plug' icon will automatically

disappearafter 3operating hours.

Air Filter

The'Air Filter' icon (F) will appearevery 50 hours (total

hours) of operation. This indicates it is time to changethe

air filter. Be sureto follow the procedures outlined in this

manual.

To reset:

1. Pressthe 'Mode' button until the 'Air Filter' screen is

displayed. (Theicon will flash.)

2. Pressand hold the 'Reset' button for more than 3

seconds.

NOTE;If not reset,the 'Air Filter' icon will automatically

disappearafter 3operating hours.

Change oil Spark plug Air filter

@ ® ®

NOTEIf not reset,the 'ChangeOil' icon will automatically

disappearafter 3operating hours.

Figure15:Maintenancereminder

Maintenance

MaintenanceChart

WAeNING

DONOTattempt any maintenance,adjustments or service

with engine and blade running. STOPengine and blade.

Removethe starter insert. Disconnectspark plug wire and

secure awayfrom spark plug. Engine and components are

HOT.Avoid serious burns, allow sufficient time for all com-

ponents to cool. Wearheavy leathergloves when handling

or working around cutting blades. Bladesare extremely

sharp and can causesevere injury.

EmissionsControl

Maintenance, replacement,or repair of the emissions control

devicesand systems may be performed byany non-road

engine repair establishment or individual. However,to obtain

"no charge" emissions control service, the work must be

performed by a factory authorized dealer.Seethe Emissions

Warranty.

ii!i i !!! i!ii i! ! !! !! ! ! !! ! i!! !i iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii!i!!i!!ii!iiiii!iiiiiiiiii!iii!!iiiiii!i!!!!i!i!ii!ii!i!i!iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii

Every8 Hoursor Daily

Checksafety interlock system

Cleandebris off mower

or Annually *

Every

25 Hours

Checkmower for loose hardware

See DealerAnnually to

Lubricate mower

Checkmower blade **

Checkmower bladestopping time

Checkdrive belt

Cleanbattery andcables

* Whichevercomes first

**Check blademore often in regionswith sandy soils or

high dust conditions.

i i: ! ! i i! ii !! ! i i i i!i iiiiii iiiiiii iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii

First5 Hours

Changeengine oil

Every8 Hours or Daily ....................

Checkengineoil level

Every25 Hoursor Annually *

Cleanengineair filter and pre-cleaner(if equipped) **

Every50 Hoursor Annually *

Changeengine oil

Replaceoil filter (if equipped)

Annually

Replaceair filter

Replacepre-cleaner(if equipped)

See Dealer Annually to

Inspect muffler and spark arrester (if equipped)

Replacespark plug

Replacefuel filter (if equipped)

Cleanengineair cooling system

* Whichevercomes first

**Clean more often in dusty conditions or when airborne

debris is present.

16 www.snapper.corn

Maintenance

ChangeEngineOil

,A WARNING

DONOTattempt any maintenance,adjustments or service

with engine and blade running. STOPengine and blade.

Removestarter insert. Disconnectspark plug wire and

secure awayfrom spark plug. Engine and components

are HOT.Avoid serious burns, allow sufficient time for all

components to cool.

ServiceAir Filter

WARNING

Neverstart or run the engine with the air cleanerassembly

(if equipped) or the air filter (if equipped) removed.

Referto the engine owner's manualfor air filter service

instructions.

1. Drain the fuel tank completely.

2. Removethe dipstick (A, Figure 16), then turn the

mower on its side. Allow the oil to drain from the oil fill

tube into an appropriate container. Disposeof usedoil

properly.

3. Placethe mower upright, then fill the enginewith

engine oil to the 'full' mark on the dipstick. Briggs &

Stratton warranty-certified SAE30lawnmower oil is

recommended. Do notoverfill.

Figure16:Drainingtheengineoi/

Maintenance

CheckSafety InterlockSystem

1. Start the mower.

2. Releasethe blade control. The engine must stop within

3 seconds.

if the engine does not stop, do notusethe mower.Bring the

mower to an authorizeddealer for service.

11.Start the engineand run for 2-3 minutes, to allow the

underside of the mower deck to dry.

CleanDebrisOff Mower

WARNING

DONOTattempt any maintenance,adjustments or service

with engine and blade running. STOPengine and blade.

Removestarter insert. Disconnectspark plug wire and

secure awayfrom spark plug. Engine and components are

HOT.Avoid serious burns, allow sufficient time for all com-

ponents to cool. Wearheavy leathergloves when handling

or working around cutting blades. Bladesare extremely

sharp and can causesevere injury.

1. Cleandirt and debris from the top of the mowerdeck.

2. Cleanany debris buildup on or around the engine,etc.

While cleaning, check components for wear or damage.

Replaceworn or damagedcomponents immediately.

Figure17:Washoutport

WashoutPort

WARNING ,A

* Useappropriate eyeprotection.

, Keeppeople and pets out of the area.

, Stay behind the handlewhile the engine is running.

, Do not attempt mowing operations while using the

washout port.

, Do not attempt to look under or reachunder the mower

deck for any reasonwhile using the washout port.

Serious injury can result.

Thewashout port allows hands-free cleaningof the

underside of the mower deck.To usethe washout port:

1. Be surethe grass bag and sidedischarge deflector are

removed.

2. Setthe height of cut to the lowest position.

3. Move the mower to a level, pavedsurface.

4. Stop the engine.

5. Connectthe male end of a standard garden hoseto the

washout port connector (A, Figure 17).

6. Turn on thewater supply to the gardenhose.

7. Start the engine and run until no more debris emerges

from underthe mower deck.

8. Stop the engine.

9. Turn off the water supply to the garden hose.

10.Disconnectthe garden hosefrom the washout port

connector.

18 www.snapper.com

Maintenance

DriveControlAdjustment

,A WARNINa ,A

DONOTattempt any maintenance,adjustments or service

with engine and blade running. STOPengine and blade.

Removestarter insert.Disconnectspark plugwire and

secure awayfrom spark plug. Engine and components

are HOT.Avoid serious burns, allow sufficient time for all

components to cool.

Thedrive control (A, Figure18) should engagethe transmis-

sion when the control is pushed forward, and should disen-

gagethe transmission when pulled all the way back.

StorageProcedure

WARNING

DONOTattempt any maintenance,adjustmentsor service

with engine and blade running. STOPengine and blade.

Removestarter insert. Disconnectspark plug wire and

secure awayfrom spark plug. Engineand components are

HOT.Avoid serious burns, allow sufficient time for all com-

ponents to cool. Wearheavy leathergloves when handling

or working aroundcutting blades. Bladesare extremely

sharp and can causesevere injury.

Preparethe mower for "end of season" storage as follows:

1. Disconnectthe spark plug wire and secureaway from

the spark plug.

2. Drainthe fuel tank and let the engine run until all fuel is

out of the carburetor.

NOTE.If using a fuel stabilizer, there is no need to drain the

fuel tank. Referto the section entitled 'Fuel System'.

Figure18:Drivecontrol

If the transmission does not engageor disengage,

adjustment may be performed asfollows:

• If the transmission does not engage,rotate the turnbuckle

(A, Figure19) one-half turn to movethe ferrules (B) out

from the turnbuckle. Checkand repeatasneeded.

• If the transmission does not disengage, rotate the turn-

buckle one-half turn to move the ferrules in toward the turn-

buckle. Checkand repeatas needed.

3. Usea brush or compressed air to remove loose debris,

then use a damp cloth to wipe down the unit.

4. Tilt the mower up on its rear wheels and inspect the

underside of the deck. (Do not tilt the mower with the

spark plug or carburetor down.) Scrapeaway stubborn

accumulation of grass with a putty knife and/or wire

brush.

5. Lubricateall exposed metal with a light coating of oil to

prevent corrosion.

6. Carefullyfold the handles,flexing the control cablesto

prevent cable damage.

7. Store the mower in a shed or other dry area,protected

from weather.

FuelSystem

Fuelcan becomestale when stored over 30 days.Stalefuel

causesacid and gum depositsto form in thefuel system or

on essentialcarburetor parts. To keepfuel fresh, use Bfiggs

& Stratton FRESHSTART® fuel stabilizer, availableas a

liquid additive or a drip concentratecartridge.

Figure19;Adjustingthedrivecable

Caution: Incorrect adjustment cancause premature wear

and/or damageto the wheel drive components.

Thereis no need to drain gasolinefrom the engine if afuel

stabilizer is added according to instructions. Runthe engine

for 2 minutes to circulatethe stabilizer throughout the fuel

system. The engine and fuel canthen bestored up to 24

months.

If gasoline in the engine has not beentreated with a fuel

stabilizer, it must be drained into an approvedcontainer. Run

the engine until it stops from lack of fuel. Theuse of a fuel

stabilizer in the storage container is recommendedto

maintain freshness.

Troubleshooting

PROBLEM PROBABLECAUSE CORRECTIVEACTION

EngineWill Not Start 1. Fueltank empty. 1. Fillfuel tank with fresh fuel.

2. Sparkplug wire disconnected. 2. Placespark plug wire onto spark plug.

3. Wiring harnessdisconnected. 3. Connectwiring harness.

4. Batterydead. 4. Chargeor replacebattery.

EngineStalls or Loses 1. Bladecontrol is releasedor is not being held 1. Bladecontrol should be held securely against

PowerAfter Running securely against drive control, drive control at alltimes during operation.

2. Fueltank empty. 2. Fillwith fuel to proper level.

3. Enginepre-cleanerand/or air cleanerdirty. 3. Cleanor replaceprecleanerand/or air cleaner.

4. Sparkplug fouled or gap set improperly. 4. Servicespark plug.

5. Water, debris or stale fuel in fuel system. 5. Drainand cleanfuel system.

ExcessiveVibration 1. Damaged,out of balanceor bent mower blade.1. Contactauthorized dealer.

2. Looseblade components. 2. Contactauthorized dealer.

3. Looseor missing air lift (if equipped). 3. Contactauthorized dealer.

4. Lumpy or frayed belt. 4. Contactauthorized dealer.

Mower Will Not Move/ 1. Build-up of debris on or around drive 1. Cleandebris.

Loss OfTraction components.

2. Transmission cable adjustment required. 2. Adjust transmission cable.

3. Drive belt requires replacement. 3. Contactauthorized dealer.

4. Damagedtransmission. 4. Contactauthorized dealer.

Cutting Grass improperly 1. Cutting heighttoo low or high. 1. Adjust cutting height.

2. Forwardspeedtoo fast. 2. Adjust to a slower speed.

3. Cutting bladedull or damaged. 3. Contactauthorized dealer.

Poor Grass Discharge 1. Forwardspeedtoo fast. 1. Adjust to a slower speed.

2. Grassis wet. 2. Mow when grass is dry.

3. Excessivelyworn or damagedblade. 3. Contactauthorized dealer.

4. Build up of grass clippings and debris under 4. Cleandeck.

deck.

5. Improper blade installed on deck. 5. Contactauthorized dealer.

6. Bladeinstalled improperly on deck. 6. Contactauthorized dealer.

Oil Leaking 1. Loosedipstick. 1. Makesure dipstick/oil filler cap is securelyin

)lace.

2. Loosedrain plug. 2. Checkand tighten drain plug.

3. Oil levelis overfilled. 3. Drainexcess oil.

4. Damagedoil seals. 4. Contactauthorized dealer.

20 www.snapper.corn

Page is loading ...

Snapper 13037130 Owner's manual

Brand: Snapper

Model: 13037130

Category: Lawnmowers

Type: Owner's manual

Download PDF

report

in other languages

español: Snapper 13037130 El manual del propietario

Snapper 13037130 Owner's manual

Snapper 13037130 Owner's manual

in other languages

Related papers

Other documents