Drive RTLREB18DDA-SF Owner's manual

rebel wheelchair

silla de ruedas rebel

fauteuil roulant rebel

www.drivemedical.com

EU Authorized Representative

Drive Medical LTD

Ainley’s Industrial Estate

Elland, West Yorkshire,

United Kingdom HX5 9JP

1. Remove all contents from the carton. Unfold the wheelchair frame by pulling

outward on sides of frame until fully opened.

2. The Rebel Wheelchair is shipped with the back in the folded down position. Pull

upwards on the back upholstery until the back locks into position. Be sure the

back is securely locked before sitting in the wheelchair.

3. Insert the arm of the wheelchair into the frame receptacle as shown in figure A.

Repeat for the other arm.

assembly instructions

4. Insert the front casters by depressing the spring loaded pin on the shaft of the

caster and slide into the frame of the wheelchair. An audible “click” will be heard

when secure (figure B).

Figure A

Figure B

5. Slide the pin of the “E” Clip into the

receiving port on the outside of the

frame Take the thumb screw and

place into the receiving port on the

inside of the frame and turn

clockwise until tight. Repeat for the

other caster. (figure C)

Thumb

Screw

E-Clip

6. Locate the port for the rear axle on the bottom back of the frame (figure D).

Depress the spring loaded button on the center of the rear wheel and slide the

axle into the frame of the wheelchair. There is a spring loaded pin in the axle that

will “click” when the axle is securely positioned. Repeat for the other wheel.

assembly instructions

Rear Axle

Port

Figure C

Figure D

To remove wheel, depress spring

loaded button and slide wheel

out from axle port.

assembly instructions

7. Place the footrests on the wheelchair by locating the hanger bracket on the

front of the frame and inserting the footrest onto the pins as shown in figure E.

The footrests come with a release lever to swing the footrests away from the chair

to remove. Repeat for the other side.

Figure E

8. To adjust the height of the footplate, locate the lock clip on the footrest and pull

up on the tab. Slide the footplate to the desired height and lock the tab as

shown in figure F.

Figure F

assembly instructions

Figure G

9. The Rebel Wheelchair comes with a calf strap for additional support. Locate the

Velcro strips and roll the strap over the footrest and attach with the Velcro

closure (figure G).

Stability - Wheelchair is designed to be safe and stable as long as center of gravity is

maintained while going about normal activities. Care must be taken while performing

activities that shift your center of gravity in the chair. Never reach so far that require

you to shift in the seat or bend over out of the chair. When you have to reach for

objects that require you to lean, be certain front casters are pointing in a forward

position that extends the wheel base and will stabilize the chair.

Ramps - Be sure of your own capabilities, limitations and strength before attempting

to go up a ramp. Correct techniques on ramp negotiation should be shown to you by

a qualified professional. Assistance is recommended when going up or down inclines

greater than 10

o

. If you must stop on an incline, avoid sudden, abrupt movement

when you resume movement. Because of backward angle of the chair, sudden abrupt

movement could cause instability. Attempting to use the wheel lock brakes could

result in accidental locking, tipping to one side, or cause a sudden stop. Avoid changing

direction when going down an incline, as this could result in instability of tipping over.

caution

use and safety

Wheel Locks - Engage both wheel locks before getting in or out of chair, leaning

forward in chair, or while in an elevator or wheelchair lift. Proper adjustment of wheel

lock is at least 1/8” when locked. Locks are engaged by pushing handle completely

forward. Adjustments to locks are made by loosening or tightening nut on the carriage

bolt. Embed lock shoe at least 1/8” by sliding clamp toward rear wheel while handle is

engaged in locked position. Tighten nut and bolt to secure in position. Test for correct

locking action before actual use.

Tires - Solid rubber tires need minimal maintenance, but should be cleaned occasionally

with a damp cloth. Replace if tires become severely worn or cracking appears.

Removal of Swing-away Foot rests/Leg rests - Release lock by pushing on the front

rigging lever. Swing-away foot rest out and sideways. Lift to remove.

General Care - Wipe chrome parts with a clean, soft cloth at least once a week. All

metal parts can be cleaned with auto wax or similar poducts. If exposed to moisture, dry

immediately. Do not use an abrasive cleanser that will scratch the finish.

To Open Chair - Open wheelchair by tilting to one side and pushing down on seat rail

until fully opened.

To Close/Fold Chair - First fold foot plates to vertical position. Grab seat with both

hands at front and back edge and lift. Or, tilt chair to one side and lift up on seat rail.

Removable Arms - Remove arms by depressing spring button and lifting arms out of

front and rear sockets.

Do not attempt to adjust or operate wheelchair without reading carefully all

instructions in this manual.

This wheelchair has not been approved as a seat that can be used within vehicles of

any kind. Always transfer wheelchair user to a vehicle manufacturers approved seat

and use safety restraints available.

Do not operate this wheelchair on roadways, streets or any surfaces with vehicular

traffic.

Do not attempt to operate on inclines 10% or greater without proper assistance.

Be sure to completely engage wheel locks when getting in and out of wheelchair or

when in elevator or wheelchair lift.

Wheelchair should be on a smooth, stable and level area with wheel locks engaged

before transferring user in or out of wheelchair.

Do not adjust foot rests any lower than 2-1/2” from floor.

When getting in or out of wheelchair, do not stand on or apply weight to foot rests.

Before reaching or leaning forward, rotate casters to front of the wheelchair engage

wheel locks to help prevent wheelchair from tipping over.

Do not lean over or apply weight to the top of wheelchair back. This can cause

wheelchair to tip over. When trying to extend arms over back, only reach as far as

your arm can extend without having to alter your seating position.

DO NOT stand on wheelchair.

DO NOT use wheel locks to slow your descent down an incline.

Abruptly changing directions while going down an incline could cause instability or

possible tipping over.

WEIGHT CAPACITY 300 LBS

warning

Page is loading ...

Your Drive Medical product is warranted to be free of defects in materials

and workmanship for the lifetime of the original consumer purchaser.

This device was built to exacting standards and carefully inspected prior to

shipment. This Lifetime Limited Warranty is an expression of our confidence

in the materials and workmanship of our products and our assurance to the

consumer of years of dependable service.

This warranty does not cover device failure due to owner misuse or

negligence, or normal wear and tear. The warranty does not extend to

non-durable components, such as rubber accessories, casters, and grips,

which are subject to normal wear and need periodic replacement.

If you have a question about your Drive device or this warranty, please

contact an authorized Drive dealer.

Drive is a trademark of Medical Depot, Inc.

Port Washington N.Y. 11050 USA Made in China

lifetime limited

warranty

Page is loading ...

Drive RTLREB18DDA-SF Owner's manual

This manual is also suitable for

Drive RTLREB18DDA-SF Owner's manual

in other languages

Related papers

Other documents