Hitachi VM-E230A User manual

Brand: Hitachi

Model: VM-E230A

Category: Camcorders

Type: User manual

This manual is also suitable for

VME-230A - Camcorder

Table of Contents

HITACHI

Instruction Manual

8mm Video Camcorder

VM-E230A

HITACHI HOME ELECTRONICS HITACHI (HSC) CANADA INC.

(AMERICA), INC. 6740 Campobello Road

3890 Steve Reynolds Blvd., Norcross, GA 30093 Mississauga, Ontario L5N 2L8

Tel. 770-279-5600 CANADA

Tel. 905-821-4545

HITACHI SALES CORPORATION OF

HAWAII, INC

3219 Koapaka Street, Honolulu, Hawaii 96819

Tel. 808-836-3621

Thank you for buying a Hitachi product. Please take time to become familiar with the

manual and how it is set up. Keep it handy for feature reference.

QR16731 © Hitachi, Ltd. 1997 Printed in Japan KN-H(N)

Table of Contents

Table of Contents........................................................................................................................................2

For Your Safety...........................................................................................................................................7

Important Safeguards ..................................................................................................................................9

IMPORTANT SAFETY INSTRUCTIONS FOR AC ADAPTER/CHARGER ......................................13

Read This First..........................................................................................................................................14

Before You Begin......................................................................................................................................15

Features...............................................................................................................................................15

Components and Accessories..........................................................................................................15

Optional RF Adapter..........................................................................................................................16

Lens Cap..............................................................................................................................................16

Using the lens cap string:..................................................................................................................16

Removing the lens cap......................................................................................................................16

Getting Started...........................................................................................................................................18

Charging the Battery..........................................................................................................................18

Additional Information........................................................................................................................19

Adjusting the Electronic Viewfinder.................................................................................................19

Eyepiece Adjustment.........................................................................................................................20

Adjustment the Hand Strap...............................................................................................................20

Loading Batteries................................................................................................................................20

Clock Battery.......................................................................................................................................21

Remote Control Batteries..................................................................................................................21

Camcorder Batteries Using Battery Pack.......................................................................................22

Removing the Battery Pack..............................................................................................................23

Checking the Battery's Charge.........................................................................................................24

Using Alkaline Dry-Cell Batteries.....................................................................................................24

Using Alternative Power Sources....................................................................................................26

Using the AC Adapter/Charger.........................................................................................................26

Using a Car Battery............................................................................................................................26

Inserting and Removing Cassettes..................................................................................................27

Inserting a Cassette...........................................................................................................................27

Removing a Cassette.........................................................................................................................28

Protecting Recorded Material...........................................................................................................28

Using the Linear Time Counter........................................................................................................28

Remaining Tape .................................................................................................................................28

Setting the Date and Time................................................................................................................29

Correcting the Date and Time ..........................................................................................................30

Getting Started, Identifying Controls........................................................................................................31

Basic Techniques.......................................................................................................................................34

Making a Basic Recording................................................................................................................34

Playing Back Your Recording...........................................................................................................35

Connecting to a Television with a VCR Attached..........................................................................35

Connecting to a Television with Audio In and Video In Jacks.....................................................35

Connecting to a Television without Audio In and Video In Jacks...............................................36

Simple Playback (Using the Electronic Viewfinder)......................................................................36

Using Still.............................................................................................................................................37

Table of Contents

Using Forward and Reverse Search...............................................................................................37

To Play Back a Recording at Double the Normal Speed.............................................................37

Advanced Techniques ...............................................................................................................................39

Date Recording...................................................................................................................................39

Using the Power Zoom......................................................................................................................40

Using the Digital Zoom ......................................................................................................................41

Using the INST. ZOOM (Instant Zoom) Button..............................................................................41

Using Auto Focus...............................................................................................................................42

Using Manual Focus..........................................................................................................................43

Using Instant Review.........................................................................................................................43

Using Quick Edit.................................................................................................................................44

Using Macro ........................................................................................................................................44

Date Search.........................................................................................................................................44

Dubbing from the Camcorder to a VCR..........................................................................................45

Remote Control Range......................................................................................................................45

Using Memory.....................................................................................................................................46

Using the Display Button...................................................................................................................47

Creating and Recording A Title........................................................................................................47

Creating a Title....................................................................................................................................48

Correcting Errors ................................................................................................................................48

Recording Title on a Tape in the Camcorder.................................................................................48

Recording a Created Title while Transferring a Tape...................................................................49

Using Audio/Video Dubbing..............................................................................................................50

Simple Programmable Edit (The edit remote control is optional)...............................................50

Programming the Remote Control for the VCR.............................................................................50

Operation.............................................................................................................................................52

To End Programmable Simple Edit.................................................................................................53

Attaching the Optional Wide or Tele Converter Lens...................................................................54

Attaching the Optional DC Camera Light .......................................................................................54

Removing the DC Camera Light......................................................................................................55

Replacing the DC Camera Light Bulb.............................................................................................55

Viewfinder Bright, Color and Tint Control.......................................................................................56

General Maintenance.................................................................................................................................57

Cleaning the camcorder Heads........................................................................................................57

Cleaning the Lens and Picture Tube of the Electronic Viewfinder.............................................57

Periodic Maintenance........................................................................................................................57

Troubleshooting..................................................................................................................................58

CAMERA RECORDING....................................................................................................................58

Symptom..............................................................................................................................................58

Check Point & Correction..................................................................................................................58

Picture does not appear in the viewfinder......................................................................................58

Remove the lens cap.........................................................................................................................58

Slide the CAM/OFF/VIDEO switch to CAM....................................................................................58

The camcorder cannot go into the recording mode, even when the start/stop button is

pressed. ...............................................................................................................................................58

Check the record protect tab on the cassette................................................................................58

Push the cassette holder embossed PUSH LOCK to close it.....................................................58

Slide the CAM/OFF/VIDEO switch to CAM....................................................................................58

Picture is out of focus. .......................................................................................................................58

Table of Contents

Make sure that FOCUS does not appear in the viewfinder. If it is displayed, press FOCUS

Control buttons to erase it.................................................................................................................58

Auto-Focus does not operate if a special effects filter is attached.............................................58

The created title does not appear....................................................................................................58

Insert the clock battery, then create a title......................................................................................58

Do not remove the clock battery after creating a title...................................................................58

PLAYBACK OF PRE-RECORDED CASSETTE...........................................................................58

Symptom..............................................................................................................................................58

Check Point & Correction..................................................................................................................58

“Play” button cannot be engaged.....................................................................................................58

Set the CAM/OFF/VIDEO switch to VIDEO...................................................................................58

No picture appears on television screen when “PLAY” is pressed. ...........................................58

(TV is connected to the camcorder by using RF output adapter................................................58

Set the television to the camcorder channel.(3 or 4) depending upon the selected channel in

the RF channel select switch of the RF output adapter...............................................................58

Interference on playback picture......................................................................................................58

When you see the playback picture on your TV, adjust fine tuning knob on television set to

obtain best picture..............................................................................................................................58

Picture bends at the top of the TV screen......................................................................................58

TV receiver is of older type. It needs to be modified to work properly with camcorder..........58

Tape is damaged. Try another cassette........................................................................................59

Color of your TV screen is too bright, too faint or change...........................................................59

TV set has VIR circuit. Turn if off during playback.......................................................................59

Date search function does not operate...........................................................................................59

Slide the CAM/OFF/VIDEO switch to VIDEO................................................................................59

Insert the clock battery, set the date and time, then start recording..........................................59

Do not remove the clock battery after recording. ..........................................................................59

Do not eject the recorded cassette. Leave it in the camcorder..................................................59

The playback picture moves rapidly and noise appears. Also sound speeded up from

normal is heard...................................................................................................................................59

The camcorder is set to the double speed playback mode. Pressing the playback button to

restore the normal playback mode. The sound also returns to the normal speed. ................59

Noise appears in the picture during double speed playback, but this does not indicate a fault.

...............................................................................................................................................................59

BATTERY CONDITION.....................................................................................................................59

Symptom..............................................................................................................................................59

Check Point & Correction..................................................................................................................59

The (

) indication in the electronic viewfinder flashes to indicate battery is discharged......59

Try another battery or charge the battery.......................................................................................59

NO OPERATION IS ACCEPTED....................................................................................................59

Symptom..............................................................................................................................................59

Check Point & Correction..................................................................................................................59

Power is turned on, but no button operation are accepted..........................................................59

Remove the power source and the date/title battery. And after about one minute, the display

in the viewfinder will be reset. Then set the information again..................................................59

The camcorder does not operate when alkaline batteries are inserted.....................................59

Check that the polarities (+,-) of the batteries are correct. ..........................................................59

Insert six batteries..............................................................................................................................59

Specifications......................................................................................................................................60

General Specifications.......................................................................................................................60

Table of Contents

Video Recorder Specifications.........................................................................................................60

Camera Specifications.......................................................................................................................60

Accessories Add Excitement.....................................................................................................................62

Available Accessories........................................................................................................................62

To Order in the United States...........................................................................................................62

By Phone .............................................................................................................................................62

By Mail..................................................................................................................................................62

FOR AUTHORIZED HITACHE SERVICE IN CANADA...............................................................62

Table of Contents

For Your Safety

The CAM/OFF/VIDEO switch turns the camcorder on and off, leaving the date/time

feature unaffected. If the unit is to be left unattended for a long period of time, turn the

camcorder off and attach the lens cap.

WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS UNIT TO

RAIN OR MOISTURE.

The camcorder and AC adapter/charger have the following caution marks.

Identifications of caution marks

This symbol warms the user that uninsulated voltage within the unit may have

sufficient magnitude to cause electrical shock. Therefore, it is dangerous to make any kind

of contact with any inside part of this unit.

This symbol alerts the user that important literature concerning the operation and

maintenance of this unit has been included. Therefore, it should be read carefully to avoid

any problems.

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT OPEN.

NO USER-SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

WARNING: TO PREVENT FIRE OR ELECTRIC SHOCK, MATCH WIDE BLADE OF

PLUG TO WIDE SLOT, AND FULLY INSERT PLUG.

WARNING: Many television programs and films are copyrighted. In certain circumstances,

This Class B digital apparatus meets all requirements of the Canadian Interference-

Causing Equipment Regulations.

The liquid crystal display (LCD) panel is made by highly precise technology. More than

99.99% of its picture elements (pixels) are effective, but some (less than 0.01%) may

appear as colored bright dots. This does not indicate a fault as the LCD panel stretches

the limits of current technology.

Warning: This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions: (1) This device may not cause harmful interference, and (2) this

device must accept any interference received, including interference that may cause

undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant of Part 15 of the FCC Rules. These limits are designed to provide

For Your Safety

reasonable protection against harmful interference in a residential installation. This

equipment generates, uses, and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the user

is encouraged to try to correct by one or more of the following measures:

-- Reorient or relocate the receiving antenna.

-- Increase the separation between the equipment and receiver.

-- Connect the equipment into an outlet on a circuit different from that to which the receiver

is connected.

-- Consult the dealer or an experienced radio/TV technician for help.

Caution to the user: Changes or modifications not expressly approved by the manufacture

could void the user's authority to operate the equipment.

"Note to CATV system installer: This reminder is provided to call the CATV system

installer's attention to Article 820-40 of the NEC that provides guidelines for proper

grounding and, in particular, specifies that the cable ground shall be connected to the

grounding system of the building, as close to the point of cable entry as practical".

Notes:

• This unit uses 8mm video format cassettes.

• It records and plays back in the SP mode (14.3 mm/sec).

• It cannot record and play back in the LP mode (7.2 mm/sec).

MOISTURE

Avoid operating your camcorder immediately after moving it from a cold place to a

warm, humid place. Give the camcorder 2 to 3 hours to stabilize in the ambient

conditions of the surroundings before inserting a cassette. When moved from a cold

place to a warm, humid place, moisture may condense on the head drum inside the

machine. This moisture could cause the tape to stick to the headwheel and damage the

headwheel or tape.

When a small amount of moisture is sensed, "TAPE" flashes in the viewfinder. Remove

the cassette and set the CAM/OFF/VIDEO switch to OFF, then wait for about one hour.

Important Safeguards

In addition to the careful attention devoted to quality standards in the manufacture of

your video product, safety is a major factor in the design of every instrument. But, safety

is your responsibility too.

This page lists important information that will help to assure your enjoyment and proper

use of a Video camcorder and accessory equipment. Please read it carefully before

operating your video product and keep it in a handy place for future reference.

INSTALLATION

1 Read and Follow Instructions -- All the safety and operating instructions should be

read before the video product is operated. Follow-all operating and use instructions.

2 Retain Instructions -- The safety and operating instructions should be retained for

future reference.

3 Heed Warnings -- Comply with all warnings on the video product and in the

operating instructions.

4 Polarized Plug -- This video product is equipped with a polarized alternating-current

line plug (a plug having one blade wider than the other). This plug will fit into the power

outlet only one way. This is a safety feature. If you are unable to insert the plug fully into

the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician

to replace your obsolete outlet. To prevent electric shock do not use this polarized plug

with an extension cord, receptacle or other outlet unless the blades can be fully inserted

without blade exposure. If you need an extension, use a polarized cord.

5 Power Sources -- This video product should be operated only from the type of power

source indicated on the marking label. If you are not sure of the type of power supply to

your home, consult your video dealer or local power company. For video products

intended to operate from battery power, or other sources, refer to the operating

instructions.

6 Overloading -- Do not overload wall outlets and extension cords as this can result in

a risk of fire or electric shock. Overloaded AC outlets and extension cords are

dangerous, and so are frayed power cords, damaged or cracked wire insulation and

broken plugs. They may result in a shock or fire hazard. Periodically examine the cord

and have it replaced by your service technician if appearance indicates damage or

deteriorated insulation.

Important Safeguards

7 Power-Cord Protection -- Power-supply cords should be routed so that they are not

likely to be walked on or pinched by items placed upon or against them, paying

particular attention to cords at plugs, convenience receptacles, and the point where they

exit from the appliance.

8 Ventilation -- Slots and openings in the cabinet are provided for ventilation to ensure

reliable operation of the video product and to protect it from overheating. These

openings must not be blocked or covered. The openings should never be blocked by

placing the video product on a bed, sofa, rug or other similar surface. This video product

should never be placed near or over a radiator or heat register. This video product

should not be placed in a built-in installation such as a bookcase or rack unless proper

ventilation is provided or the video product manufacturer's instructions have been

followed.

9 Attachments -- Do not use attachments unless recommended by the video product

manufacturer as they may cause hazards.

Caution: Maintain electrical safety. Powerline operated equipment or accessories

connected to this unit should bear the UL listing mark or CSA certification mark on the

accessory itself and should not have been modified so as to defeat the safety features. This

will help avoid any potential hazard from electric shock or fire. If in doubt, contact qualified

service personnel.

10 Water and Moisture -- Do not use this video product near water - for example, near

a bath tub, wash bowl, kitchen sink, or laundry tub, in a wet basement, or near a

swimming pool, and the like.

11 Accessories -- Do not place this video product on an unstable card, stand, tripod,

bracket, or table. The video product may fall, causing serious injury to a child or adult,

and serious damage to the appliance. Use only with a cart, stand, tripod, bracket, or

table recommended by the manufacturer, or sold with the video product. Any mounting

of the product should follow the manufacturer's instructions, and should use a mounting

accessory recommended by the manufacturer.

11A An appliance and cart combination should be moved with care. Quick stops,

excessive force, and uneven surfaces may cause the appliance and cart combination to

overturn.

12 Outdoor Antenna Grounding -- If an outside antenna or cable system is

connected to the video product, be sure the antenna or cable system is grounded so as

to provide some protection against voltage surges and built-up static charges. Section

810 of the National Electrical Code, ANSI/NFPA No. 70, provides information with

Important Safeguards

respect to proper grounding of the mast and supporting structure, grounding of the lead-

in wire to an antenna discharge unit, size of grounding conductors, location of antenna-

discharge unit, connection to grounding electrodes, and requirements for the grounding

electrode. See example below:

EXAMPLE OF ANTENNA GROUNDING

13 Power Lines -- An outside antenna system should not be located in the vicinity of

overhead power lines or other electric light or power circuits, or where it can fall into

such power lines or circuits. When installing an outside antenna system, extreme care

should be taken to keep from touching or approaching such power lines or circuits as

contact with them might be fatal. Installing an outdoor antenna can be hazardous and

should be left to a professional antenna installer.

USE

14 Cleaning -- Unplug this video product from the wall outlet before cleaning. Do not

use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.

15 Object and Liquid Entry -- Never push objects of any kind into this video product

through openings as they may touch dangerous voltage points or short-out parts that

could result in a fire or electric shock. Never spill liquid of any kind on the video

product.

16 Lightning -- For added protection for this video product during a lightning storm, or

when it its left unattended and unused for long periods of time, unplug it from the wall

outlet and disconnect the antenna or cable-system. This will prevent damage to the

video product due to lightning and power-line surges.

SERVICE

17 Servicing -- Do not attempt to service this video product yourself as opening or

removing covers may expose you to dangerous voltage or other hazards. Refer all

servicing to qualified service personnel.

18 Conditions Requiring Service -- Unplug this video product from the wall outlet and

refer servicing to qualified service personnel under the following conditions.

a. When the power-supply cord or plug is damaged

b. If liquid has been spilled, or objects have fallen into the video product.

c. If the video product has been exposed to rain or water.

d. If the video product does not operate normally by following the operating instructions.

Adjust only those controls that are covered by the operating instructions. Improper

adjustment of other controls may result in damage and will often require extensive work

by a qualified technician to restore the video product to its normal operation.

Important Safeguards

e. If the video product has been dropped or the cabinet has been damaged.

f. When the video product exhibits a distinct change in performance - this indicates a

need for service.

19 Replacement Parts -- When replacement parts are required, have the service

technician verify that the replacements he uses have the same safety characteristics as

the original parts. Use of replacements specified by the video product manufacturer can

prevent fire, electric shock or other hazards.

20 Safety Check -- Upon completion of any service or repairs to this video product, ask

the service technician to perform safety checks recommended by the manufacturer to

determine that the video product is in safe operating condition.

21 Heat -- The product should be situated away from heat sources such as radiators,

heat registers, stoves, or other products (including amplifiers) that produce heat.

IMPORTANT SAFETY INSTRUCTIONS FOR AC ADAPTER/CHARGER

1. Save these Instructions -- This page contains important safety and operating

instructions for AC Adapter/Charger Model VM-AC 85A.

2. Before using AC Adapter/Charger, read all instructions and cautionary markings on

(1) AC Adapter/Charger, (2) battery and (3) product using battery.

3. Also read all instructions on pages 4 and 5.

4. Caution -- To reduce risk of injury, charge only rechargeable battery, VM-BP82G, VM-

BP82 or VM-BP84.

Other types of batteries may burst causing personal injury and damage.

5. Do not expose charger to rain or snow.

6. Use of an attachment nor recommended or sold by the battery charger manufacturer

may result in a risk of fire, electric shock, or injury to persons.

7. To reduce risk of damage to electric plug and cord, pull by plug rather than cord when

disconnecting charger.

8. Make sure cord is located so that it will not be stepped on, tripped over, or otherwise

subjected to damage or stress.

9. Do not operate charger with damaged cord or plug - replace them immediately.

10. An extension cord should not be used unless absolutely necessary.

Use of improper extension cord could result in a risk of fire and electric shock. If

extension cord must be used, make sure:

A. The pins on plug of extension cord are the same number, size, and shape as those

of plug on charger.

B. That extension cord is properly wired and in good electrical condition; and

C. That wire size should be met below:

Minimum

AWG size Length of extension cord (feet)

18 Equal to or less than 100

16 Equal to or less than 150

11. Do not operate charger if it has received a sharp blow, been dropped, or otherwise

damaged in any way; take it to a qualified serviceman.

12. Do not disassemble charger: take it to a qualified serviceman when service or repair

is required. Incorrect reassembly may result in a risk of electric shock or fire.

13. To reduce risk of electric shock, unplug charger from outlet before attempting any

maintenance or cleaning.

Read This First

To guide you, we've included:

• A "Before You Begin" section containing important cautions for your family's safety as

well as instruction for getting your video camcorder ready for use. Please read and

understand this section thoroughly before moving on.

• A "Getting Started" section to familiarize yourself with the controls and prepare you for

recording.

• A "Basic Techniques" section to allow you to use your video camcorder quickly and

confidently before advancing to the more sophisticated features of the Hitachi VM-

E230A.

• "Advanced Techniques" to help you with some of the exciting, sophisticated features

of the Hitachi VM-E230A. We hope you will take the time to learn about these functions

since they have been designed for you. You can use the video camcorder without

reading this section.

• A "General Maintenance" section to help keep your purchase in good repair.

We want this manual to be as helpful as possible, so it includes two easy ways to find

the information you need:

• A quick index for the information you use most often (this page).

• A detailed table of contents directing you to specific information quickly (page 10).

Get to know your video camcorder by using this manual, and get to know Hitachi. We

appreciate your business.

Quick Index

Charging the Battery.....12

Making a Basic Recording.....25

Playing Back Your Recording.....26

Using Power Zoom.....33

Using Digital Zoom.....33

Dubbing from camcorder to VCR.....38

Before You Begin

Any problems that occur as a result of any of the following conditions will not be covered

by our warranty.

 Be careful that no water, dust or sand enters the camcorder and all accessories.

 When you shoot at a scene which contains an extremely bright object such as the sun

or a light source, a bright vertical bar may appear in the picture.

Your camcorder is functioning properly, but the solid-state pickup device (C.C.D) usually

causes this as an inherent characteristic. Try to avoid shooting an excessive bright

object directly.

 Be sure not to leave the camcorder in a place where the temperature exceeds 140°F

(60°C), or the pickup device may be damaged.

Dangerous includes:

• Inside a car with the windows closed and in direct sunshine.

• Near heating appliances.

 Do not leave the viewfinder lens facing sunlight for a prolonged period, or the liquid

crystal display (LCD) panel may be damaged.

Features

• Easy to use

• Instant zoom

• 24x zoom ratio

• Recorded date search

• Automatic title recording

Components and Accessories

Check that you have all the following components and accessories before preceding.

1. Audio/Video output cable

2. Battery pack

3. AC adapter/charger

4. Batteries for date/title

5. DC cord

6. Lens cap string

7. Remote control

+8. Batteries for remote control

Before You Begin

Optional RF Adapter

If you wish to connect this camcorder to a television that does not have audio/video

input jacks you will need to use the optional RF adapter model VM-RF86A (R).

The RF adapter can be purchased by calling the telephone number below. For your

convenience Visa, Master Card, and American Express credit cards are accepted. The

RF adapter can also be purchased by mail by sending either money order or your credit

card information to the following address:

HiTRON, Inc.

675, Old Peachtree RD.

Suwanee, GA 30174

Tel: 1-800-995-4500

For more information concerning the purchase of camcorder accessories, please see

the optional accessory listing on page 59.

Lens Cap

Using the lens cap string:

Pass the string through the lens cap and grip belt and attach it as shown in the figure.

Removing the lens cap

Always attach the lens cap to protect the lens when carrying or storing the camcorder.

Before You Begin

During shooting attach the lens cap as shown in the figure to prevent it from being lost.

Getting Started

This section guides you through the initial preparation of the camcorder. None of these

processes are complex. Set aside some time, relax, and familiarize yourself with this

quality instrument.

Enjoy getting to know all about your Hitachi 8mm camcorder. The more comfortable and

familiar you are with the machine and its features, the more you can make it do for you.

Let's get started!

It is crucial that you read and understand all the safety instructions before you begin. If

you haven't read the safety instructions yet, please take the time to do so now.

Charging the Battery

The first step is to set the battery to charge. It takes approximately an hour (VM-

BP82G), enough time to familiarize yourself with some of the basic features of the

camcorder. Once fully charged the battery will give an operating time of approximately

60 minutes, but this is reduced to a half to one-third depending on how often you use

zoom and start/stop functions.

Charge the battery at a temperature range of 50°F(10°C) - 86°F(30°C) to prevent

damage to the battery.

1. Plug the AC adapter/charger power cord into an AC outlet. Make sure that the wide

blade fits into the wide slot. If it doesn't fit try reversing it. If you still cannot make fit the

blades fully into the outlet either contact an electrician to replace your obsolete outlet, or

use a polarized cord or outlet accessory.

2. To insert the battery into the charger align the reference arrow on the battery with the

reference arrow on the AC adapter/charger. Push the battery till it is flush with the AC

adapter/charger sliding it in the direction of the arrow as shown in the figure.

3. The CHARGE light remains on while the battery charges, turning off when charging

completes.

Note: Remove the DC cord from the AC adapter/charger before attempting to charge the

battery. The CHARGE light flashes if the DC cord remains connected while you attempt to

charge the battery.

Note: Do not operate the battery at temperature below 14°F (-10°C) or above 95°F (35°C).

At extremely low temperatures operation time decreases, while at high temperature the

battery may be damaged.

After charging set the mark switch to red so that you may quickly identify

whether the battery is charged or uncharged.

Note: The marker switch does not guarantee the batteries charge status.

Getting Started

Additional Information

To use a battery in optimum condition:

• Use the battery until the low charge light ( ) flashes. Using a battery for a short time

and then recharging it may shorten the operation time.

• It is recommended to refresh a battery before recharging it when it has not been used

for long time; otherwise its operation time becomes short. Press the refresh button.

After refreshing is complete, the REFRESH light turns off and the CHARGE light turns

on and charging begins automatically.

Refreshing a fully charged battery takes approximately 4 hours (VM-BP82G), adding

considerable time to battery charging.

With repeated normal charging and use the battery will gradually lose operating time.

When operation time becomes too short to be useful, replace the battery.

If the POWER light begins to flash during charging, remove the battery and then

reattach it to the AC charger/adapter. If the POWER light continues to flash after several

attempts to attach it, the battery is unable to take a charge and must be replaced.

Do not attach a hot battery to the AC adapter/charger. Allow it to cool. Attaching a hot

battery to the AC adapter/charger causes the POWER light to flash.

THERE ARE NO USER-SERVICEABLE PARTS INSIDE THE BATTERY OR AC

ADAPTER/CHARGER.

THROWING THE BATTERY INTO FIRE OR EXPOSING IT TO EXCESSIVE HEAT

(ABOVE 149°F [65°C]) MAY CAUSE INJURY.

SHORTING THE BATTERY'S TERMINAL INCREASES RISK OF FIRE OR

ELECTRICAL SHOCK.

ATTENTION:

The product that you have purchased contains a rechargeable battery. The battery is

recyclable. At the end of its useful life, under various state and local laws, it may be

illegal to dispose of this battery into the municipal waste stream. Check with your local

solid waste officials for details in your area for recycling options or proper disposal.

Adjusting the Electronic Viewfinder

The electronic viewfinder adjusts simply by pivoting it to a position where it is

comfortable and easy to see through. Place the viewfinder back in its original position

Getting Started

before storing the camcorder in its case or carrying the camera recorder around to avoid

damaging the viewfinder or camcorder.

CAUTION:

Do not hold the unit by the electronic viewfinder when carrying as this could cause a

malfunction.

Eyepiece Adjustment

To use the electronic viewfinder, turn this control for your optimum focus adjustment.

Adjustment the Hand Strap

Adjust the hand strap to best fit your hand. After adjustment, hook the hand strap's pad

securely.

Loading Batteries

Page is loading ...

Hitachi VM-E230A User manual

Brand: Hitachi

Model: VM-E230A

Category: Camcorders

Type: User manual

This manual is also suitable for

VME-230A - Camcorder

Download PDF

report

Hitachi VM-E230A User manual

This manual is also suitable for

Hitachi VM-E230A User manual

Related papers

Other documents