NEC vt 770 Owner's manual

Portable Projector

VT770

User’s Manual

2

Important Information

Safety Cautions

Precautions

Please read this manual carefully before using your NEC VT770 Projector and keep the manual handy for future

reference. Your serial number is located on the bottom of your projector. Record it here:

CAUTION

To turn off main power, be sure to remove the plug from power outlet.

The power outlet socket should be installed as near to the equipment as possible, and should be easily

accessible.

CAUTION

TO PREVENT SHOCK, DO NOT OPEN THE CABINET.

NO USER-SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED NEC SERVICE PERSONNEL.

This symbol warns the user that uninsulated voltage within the unit may be sufficient to cause electrical

shock. Therefore, it is dangerous to make any kind of contact with any part inside of the unit.

This symbol alerts the user that important information concerning the operation and maintenance of this

unit has been provided.

The information should be read carefully to avoid problems.

WARNING: TO PREVENT FIRE OR SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.

DO NOT USE THIS UNIT’S PLUG WITH AN EXTENSION CORD OR IN AN OUTLET UNLESS ALL THE PRONGS

CAN BE FULLY INSERTED.

DO NOT OPEN THE CABINET. THERE ARE HIGH-VOLTAGE COMPONENTS INSIDE. ALL SERVICING MUST

BE DONE BY QUALIFIED NEC SERVICE PERSONNEL.

DOC Compliance Notice

This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.

Acoustic Noise Information Ordinance-3. GSGV:

The sound pressure level is less than 70 dB (A) according to ISO 3744 or ISO 7779.

CAUTION

•Avoid displaying stationary images for a prolonged period of time.

Doing so can result in these images being temporarily sustained on the surface of the LCD panel.

If this should happen, continue to use your projector. The static background from previous images will disap-

pear.

• Do not put the projector on its side when the lamp is turned on.

Doing so may cause damage to the projector.

Copyright

©

2003 by NEC Viewtechnology, Ltd.

WARNING TO CALIFORNIA RESIDENTS:

Handling the cables supplied with this product, will expose you to lead, a chemical known to the State of California

to cause birth defects or other reproductive harm. Wash hands after handling.

3

Important Information

RF Interference

WARNING

The Federal Communications Commission does not allow any modifications or changes to the unit EXCEPT those

specified by NEC Soluctions (America), Inc. in this manual. Failure to comply with this government regulation could

void your right to operate this equipment. This equipment has been tested and found to comply with the limits for a

Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment generates, uses, and can radi-

ate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful

interference to radio communications. However, there is no guarantee that interference will not occur in a particular

installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try to correct

the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio / TV technician for help.

In UK, a BS approved power cable with moulded plug has a Black (five Amps) fuse installed for use with this equip-

ment. If a power cable is not supplied with this equipment please contact your supplier.

Important Safeguards

These safety instructions are to ensure the long life of your projector and to prevent fire and shock. Please read them

carefully and heed all warnings.

Installation

1. For best results, use your projector in a darkened room.

2. Place the projector on a flat, level surface in a dry area away from dust and moisture.

3. Do not place your projector in direct sunlight, near heaters or heat radiating appliances.

4. Exposure to direct sunlight, smoke or steam can harm internal components.

5. Handle your projector carefully. Dropping or jarring can damage internal components.

6. Do not place heavy objects on top of the projector.

7. If you wish to have the projector installed on the ceiling:

a. Do not attempt to install the projector yourself.

b. The projector must be installed by qualified technicians in order to ensure proper operation and reduce the

risk of bodily injury.

c. In addition, the ceiling must be strong enough to support the projector and the installation must be in accor-

dance with any local building codes.

d. Please consult your dealer for more information.

4

Important Information

Fire and Shock Precautions

1. Ensure that there is sufficient ventilation and that vents are unobstructed to prevent the build-up of heat inside

your projector. Allow at least 4 inches (10 cm) of space between your projector and a wall.

2. Prevent foreign objects such as paper clips and bits of paper from falling into your projector.

Do not attempt to retrieve any objects that might fall into your projector.

Do not insert any metal objects such as a wire or screwdriver into your projector. If something should fall into

your projector, disconnect it immediately and have the object removed by a qualified NEC service personnel.

3. Do not place any liquids on top of your projector.

4. Do not look into the lens while the projector is on. Serious damage to your eyes could result.

5. Keep any items such as magnifying glass out of the light path of the projector. The light being projected from the

lens is extensive, therefore any kind of abnormal objects that can redirect light coming out of the lens, can

cause unpredictable outcome such as fire or injury to the eyes.

6. Do not cover the lens with the supplied lens cap or equivalent while the projector is on. Doing so can lead to

melting of the cap and possibly burning your hands due to the heat emitted from the light output.

7. The projector is designed to operate on a power supply of 100-240 V 50/60 Hz AC. Ensure that your power

supply fits this requirement before attempting to use your projector.

8. Handle the power cable carefully and avoid excessive bending.

A damaged cord can cause electric shock or fire.

9. If the projector is not to be used for an extended period of time, disconnect the plug from the power outlet.

10. Do not touch the power plug during a thunderstorm. Doing so can cause electrical shock or fire.

CAUTION

• Do not try to touch the ventilation outlet on the left side (when seen from the front) as it can become heated

while the projector is turned on.

• Do not use the tilt-foot for purposes other than originally intended.

Misuses such as gripping the tilt-foot or hanging on the wall can cause damage to the projector.

• Do not send the soft carrying case by parcel delivery service or cargo shipment. The projector inside the soft

carrying case could be damaged. (However, it is possible to use it as a carriercase on board.)

• Enable High-Speed Fan mode if you continue to use the projector for consecutive days. (From the menu,

select [Setup] → [Page 4] → [Fan Mode].)

• Do not unplug the power cable from the wall outlet under any one of the following circumstances.

Doing so can cause damage to the projector:

* While the Hour Glass icon appears.

* While the cooling fans are running. (The cooling fans continue to work for 10 seconds after the projector is

turned off).

5

Lamp Replacement

•To replace the lamp, follow all instructions provided on page 109.

• Be sure to replace the lamp when the message “The lamp has reached the end of its usable life.

Please replace the lamp.” appears. If you continue to use the lamp after the lamp has reached the end of

its usable life, the lamp bulb may shatter, and pieces of glass may be scattered in the lamp case. Do not touch

them as the pieces of glass may cause injury.

If this happens, contact your NEC dealer for lamp replacement.

• Allow a minimum of 10 seconds to elapse after turning off the projector.

Then turn off the main power switch, disconnect the power cable and allow 60 minutes to cool the projector

before replacing the lamp.

Important Information

6

Table of Contents

Important Information ........................................................................ 2

1. Introduction ...................................................................................... 8

 What's in the Box? ........................................................................................................ 9

 Introduction to the Projector ....................................................................................... 10

 Part Names of the Projector ....................................................................................... 12

Carrying the Projector ........................................................................................... 13

Top Features ......................................................................................................... 14

Te r minal Panel Features ....................................................................................... 15

 Part Names of the Remote Control ............................................................................ 17

2. Installation and Connections .................................................... 20

 Setting Up the Screen and the Projector .................................................................... 21

Selecting a Location.............................................................................................. 21

Throw Distance and Screen Size .......................................................................... 22

 Making Connections ................................................................................................... 23

Enabling the computer’s external display .............................................................. 23

Connecting Your PC or Macintosh Computer ........................................................ 23

To connect SCART output (RGB) ......................................................................... 24

Connecting an External Monitor ........................................................................... 25

Connecting Your DVD Player with Component Output .......................................... 26

Connecting Your VCR or Laser Disc Player .......................................................... 27

Connecting the Supplied Power Cable ................................................................. 28

3. Projecting an Image (Basic Operation) ................................. 29

 Tu r ning on the Projector ............................................................................................. 30

 Selecting a Source ..................................................................................................... 32

 Adjusting the Picture Size and Position ...................................................................... 33

 Correcting Keystone Distortion ................................................................................... 35

 Optimizing RGB Picture Automatically ....................................................................... 37

 Tur ning Up or Down Volume ....................................................................................... 37

 Tur ning off the Projector ............................................................................................. 38

 After Use..................................................................................................................... 38

4. Convenient Features .................................................................... 39

 Switching Operation Mode between Computer and Projector.................................... 40

 Tur ning Off the Image and Sound ............................................................................... 40

 Freezing a Picture....................................................................................................... 40

 Using the Pointer ........................................................................................................ 41

 Enlarging and Moving a Picture.................................................................................. 41

 Getting the On-line Help ............................................................................................. 42

 Using a USB Mouse ................................................................................................... 42

 Using the Remote Mouse Function ............................................................................ 43

 Correcting Horizontal and Vertical Keystone Distortion (Cornerstone) ....................... 44

쐅 Making Freehand Drawings on a Projected Image (ChalkBoard) .............................. 47

7

Table of Contents

쐈

Storing Images Displayed on the Projector on the PC card or USB Memory (Capture)

.......... 48

쐉 Preventing the Unauthorized Use of the Projector ..................................................... 49

씈 Using a USB Memory Device or USB Memory Card Reader ..................................... 54

5. Using the Viewer ........................................................................... 55

 Making the Most out of the Viewer Function ............................................................... 56

 Operating the Viewer Function from the Projector ...................................................... 58

쐋 Changing Background Logo ....................................................................................... 64

6.

Using Dynamic Image Utility 2.0 on the supplied CD-ROM

................... 65

 End User License Agreement.................................................................................... 66

 Introduction ................................................................................................................ 67

 Operating Environment .............................................................................................. 68

 Equipment Connections and Settings ....................................................................... 69

 Software Installation .................................................................................................. 69

 Starting/Exiting the Software ..................................................................................... 70

 Troubleshooting ......................................................................................................... 72

7. Using On-Screen Menu ................................................................ 73

 Using the Menus......................................................................................................... 74

 Menu tree ................................................................................................................... 75

 Menu Elements........................................................................................................... 77

 Menu Descriptions & Functions [Adjust] ..................................................................... 78

 Menu Descriptions & Functions [Image] ..................................................................... 82

 Menu Descriptions & Functions [Setup] ..................................................................... 85

 Menu Descriptions & Functions [Information] ........................................................... 102

 Menu Descriptions & Functions [Reset] ................................................................... 103

 Entry List .................................................................................................................. 104

8. Maintenance ................................................................................. 106

 Cleaning the Filters.................................................................................................. 107

 Cleaning the Cabinet ............................................................................................... 107

 Cleaning the Lens.................................................................................................... 108

 Replacing the Lamp and Filters ............................................................................... 109

9. Appendix ........................................................................................ 112

 Troubleshooting ....................................................................................................... 113

 Specifications .......................................................................................................... 116

 Cabinet Dimensions ................................................................................................ 118

 Pin Assignments of D-Sub COMPUTER 1/2 Input Connector ................................ 119

 Compatible Input Signal List .................................................................................... 120

 PC Control Codes and Cable Connection ............................................................... 121

 Using Software Keyboard ........................................................................................ 122

 TravelCare Guide ..................................................................................................... 123

1

Introduction

 What's in the Box? ....................................................... 9

 Introduction to the Projector ...................................... 10

 Part Names of the Projector ...................................... 12

Carrying the Projector .......................................................................................... 13

Top Features ......................................................................................................... 14

Ter minal Panel Features ....................................................................................... 15

 Part Names of the Remote Control ........................... 17

9

1. Introduction

 What's in the Box?

Make sure your box contains everything listed. If any pieces are missing, contact your dealer.

Please save the original box and packing materials if you ever need to ship your VT770 Projector.

ZOOM

F

O

C

U

S

3

D

R

E

F

O

R

M

S

O

U

R

C

E

S

E

L

E

C

T

S

T

A

T

U

S

L

A

M

P

C

A

R

D

P

O

W

E

R

O

N

/

S

T

A

N

D

B

Y

A

U

T

O

A

D

J

U

S

T

M

E

N

U

E

N

T

E

R

C

A

N

C

E

L

P

J

SOURCE

FREEZE

3D-R

EF

O

R

M

ASPECT

POINTER

V

O

L

U

M

E

MAGNIFY

PICTURE

O

F

V

I

D

E

O

P

O

W

E

R

O

N

VIEWER

PIC-MUTE

SLIDE

HELP

S

E

L

EC

T

12

S-

VID

E

O

AUTO ADJ.

COMPUTER

COMPONENT

Projector

Lens cap

(24F39571)

Remote control

(7N900451)

Batteries (AA



2)

Power cable

(US: 7N080212)

(EU: 7N080005)

USB cable

(7N520013)

RGB signal cable

(7N520012)

Soft carrying case

(24BS7311)

Quick

Connect

Guide

Important

Information

CD-ROM

• User’s manual (7N950422)

• User Supportware (7N950431)

For North America only

Registration card

Limited warranty

For Europe only

Guarantee policy

(7N8P4101)

(7N8P4111)

10

1. Introduction

 Introduction to the Projector

This section introduces you to the VT770 Projector and describes key features and controls.

Congratulations on Your Purchase of the VT770 Projector

The VT770 is a sophisticated three panel LCD XGA projector that produces an enhanced display in less than an 8-

pound (4kg) design. With the VT770 you will be able to project images up to 300” (measured diagonally). Enjoy crisp

and sharp large screen display from your DVD player, VCR, satellite hookup, HDTV source, PC, Workstation or

Macintosh computer (desktop or notebook) and images from your digital camera PC Card, compact flash memory or

USB storage device. The VT770 provides for enhanced security options to help deter projector theft and provides for

full projector control through RS232 support. With input and output flexibility, long lamp life and a full function remote,

the VT770 lets you enjoy larger than life viewing from a compact and easy to setup and use projector.

Features you’ll enjoy on the VT770:

•Automatic vertical keystone correction for fast and easy application setup

• Built-in Wall Color Correction presets provide for adaptive color correction when projecting onto non-white

screen material.

• 3D Reform™ enhanced image technology for increased projector versatility that provides for horizontal, vertical

and diagonal keystone correction (allows for positioning the projector in off center locations in the room and still

get aligned images)

• USB memory or PC card interfaces provide for computerless presentations

• Enhanced smart security settings for password protection, control panel lock, menu lock and PC card protection

key to help prevent unauthorized access, adjustments and theft deterrence

• UXGA compatible, XGA native resolution

•Variable audio out control of external amplified speakers via the projector

• Extensive user adjustable picture and color management settings

• Core technologies – Advanced AccuBlend™, Advanced AutoSense™, VORTEX Technology Plus™ for highest

quality of image display and ease of use

• Display 16:9 or 4:3 aspect ratio information and fill the screen

• HDTV (1080i, 720p) and SDTV (480p, 480i) compatibility

• Digital photo viewer to display larger than life images from your digital cameras PC card, compact flash card or

USB storage device

• Easy set up, use and operation

• Manual zoom and manual focus lens

• Eco-mode™ lamp technology for increased lamp life, reduced energy consumption and overall total cost of

ownership savings

• Wireless remote control operation

• External control via RS232

11

• NEC’s exclusive Advanced AccuBlend intelligent pixel blending technology provides for extremely accurate

image compression and HDTV (1920x1080 and 1280x720) display resolution*.

• Supports most IBM VGA, SVGA, XGA, Macintosh, component signal (YCbCr/YPbPr) or other RGB signals

within a horizontal frequency range of 15 to 100 kHz and a vertical frequency range of 50 to 120 Hz. This

includes NTSC, NTSC4.43, PAL, PAL-M, PAL-N, PAL60 and SECAM standard video signals

NOTE: Composite video standards are as follows:

NTSC: U.S. TV standard for video in U.S. and Canada.

PAL: TV standard used in Western Europe.

PAL-N: TV standard used in Argentine, Paraguay and Uruguay.

PAL-M: TV standard used in Brazil.

PAL60: TV standard used for NTSC playback on PAL TVs.

SECAM: TV standard used in France and Eastern Europe.

NTSC4.43: TV standard used in Middle East countries.

*1 Do not attempt to mount the projector on the ceiling yourself. To ensure proper operation and reduce the risk

of bodily injury a qualified technician must install the projector. In addition, the ceiling must be strong enough

to support the projector and the installation must be in accordance with any local building codes. Please

consult your dealer for more information.

*2 HDTV 1080i (1920  1080) and HDTV 720 p (1280  720) are displayed with NECs Advanced AccuBlend

technology.

Thank you for your purchase of the NEC VT770 projector.

For additional information, please visit our website at:

US: http://www.necvisualsystems.com

Europe: http://www.nec-europe.com/

Global: http:www.nec-pj.com/

1. Introduction

12

1. Introduction

 Part Names of the Projector

Z

O

M

F

O

C

U

S

3D REFORM

SOURCE

SELECT

STATUS

LAMP

PC CAR

D

POWER

O

N

/

S

T

A

N

D

B

Y

AU

T

O

A

D

JU

S

T

M

E

N

U

E

N

T

E

R

C

A

N

C

E

L

Controls

(See page 14)

Zoom lever

(See page 34)

Focus ring

(See page 34)

Lens

Lens cap

Remote sensor

(See page 98)

Adjustable Tilt Foot Button

(See page 33)

Carrying Handle

Adjustable Tilt Foot

(See page 33)

Ventilation (outlet)

Heated air exhausted from

here.

Lamp Cover Screw

Lamp Cover

(See page 109)

A

C

IN

C

O

M

P

O

N

E

N

T

YC

b

/

P

b

C

r

/

P

r

A

U

D

I

O

A

U

D

I

O

A

U

D

I

O

S

-

V

I

D

E

O

C

O

M

P

U

T

E

R

1

A

U

D

I

O

P

C

A

R

D

USB(COMPUTER)

USB(M

OUSE)

M

O

N

I

T

O

R

O

U

T

C

O

M

P

U

T

E

R

2

P

C

O

N

T

R

O

L

/

M

O

N

O

V

I

D

E

O

R

C

O

M

P

O

N

E

N

T

Y

C

b

/

P

b

C

r

/

P

r

A

U

D

I

O

A

U

D

I

O

L

/

M

O

N

O

R

PC CARD

3D REFORM

SOURCE

STATUS

LAMP

POWER

O

N

/

S

T

A

N

D

B

Y

A

U

T

O

A

D

J

U

S

T

S

E

L

E

C

T

M

E

N

U

E

N

T

E

R

C

A

N

C

E

L

ZOOM

F

O

C

U

S

Ventilation (inlet) / Filter Cover

AC Input

Connect the supplied power cable's

two-pin plug here, and plug the

other end into an active wall outlet.

(See page 28)

Main Power Switch

When you plug the supplied power

cable into an active wall outlet and

turn on the Main Power switch, the

POWER indicator turns orange and

the projector is in standby mode.

(See page 30)

Stereo Speaker

Remote sensor

(See page 98)

Built-in Security Slot ( )*

Ter minal Panel

(See page 15)

* This security slot supports the MicroSaver ® Security System. MicroSaver ® is a registered trademark of

Kensington Microware Inc. The logo is trademarked and owned by Kensington Microware Inc.

13

1. Introduction

Carrying the Projector

Always carry your projector by the handle.

Ensure that the power cable and any other cables con-

necting to video sources are disconnected before mov-

ing the projector.

When moving the projector or when it is not in use, cover

the lens with the lens cap.

ZOOM

F

O

C

U

S

14

1. Introduction

Top Features

SELECT

3D REFORM

SOURCE

STATUS

LAMP

PC CARD

POWER

ON/STAND BY

AUTO ADJUST

M

E

N

U

E

N

T

E

R

C

A

N

C

E

L

3

2

4

17

10 12 11

5

89

6

1. POWER Button (ON / STAND BY) ( )

Use this button to turn the power on and off when the

main power is supplied.

To turn on or off the projector, press and hold this but-

ton for a minimum of two seconds.

2. POWER Indicator

When this indicator is green, the projector is on; when

this indicator is orange, it is in standby mode. See the

Power Indicator section on page 113 for more details.

3. STATUS Indicator

If this light blinks red rapidly, it indicates that an error

has occurred, the lamp cover is not attached properly

or the projector has overheated.

If this light remains orange, it indicates that you have

pressed a cabinet button while the Cabinet Button is

locked. See the Status Indicator section on page 113

for more details.

4. LAMP Indicator

If this light blinks red rapidly, it's warning you that the

lamp has reached the end of its usable life. After this

light appears, replace the lamp as soon as possible

(See page 109). If this is lit green continually, it indi-

cates that the lamp mode is set to Eco. See the Lamp

Indicator section on page 113 for more details.

5. SOURCE Button

Use this button to select a video source such as a PC,

VCR, DVD player or Viewer (PC card).

Press and release this button quickly to display the

Source List.

Each time this button is pressed for a minimum of ONE

second, the input source will change as follows:

Computer1 → Computer2 → Component → Video →

S-Video → Viewer → Entry List → Computer1 → ...

If no input signal is present, the input will be skipped.

6. AUTO ADJ. Button

Use this button to adjust Position-H/V and Pixel Clock/

Phase for an optimal picture (See page 37). Available

for the RGB signal only.

7. 3D REFORM Button

Press this button to enter 3D Reform mode to correct

the keystone (trapezoidal) distortion, and make the

image square. See pages 35 and 44.

8. MENU Button

Displays the menu.

9. SELECT 왖왔왗왘 / Volume Buttons

왖왔 : Use these buttons to select the menu of the

item you wish to adjust.

왗왘 : Use these buttons to change the level of a se-

lected menu item.

A press of the 왘 button executes the selec-

tion. When no menus appear, these buttons

work as a volume control.

When an image is magnified, the SELECT 왖왔왗왘

button moves the image.

10. ENTER Button

Executes your menu selection and activates items

selected from the menu.

11. CANCEL Button

Pressing this button will return to the previous menu.

While you are in the main menu, pressing this button

will close the menu.

12. PC CARD Access Indicator

Lights while accessing a PC card.

15

1. Introduction

COMPONENT

Y Cb/Pb Cr/Pr

AUDIO

L/MONO

S-VIDEO

COMPUTER 1AUDIO

PC CARD

USB(COMPUTER)

USB(MOUSE)

MONITOR OUT

COMPUTER 2

PC CONTROL

R

L/MONOVIDEO R

134

52

Te r minal Panel Features

1. COMPUTER 1 Input Connector (Mini D-Sub 15 Pin)

Connect your computer or other analog RGB equip-

ment such as IBM compatible or Macintosh comput-

ers. Use the supplied RGB cable to connect to your

computer.

COMPUTER 1 AUDIO Input Mini Jack (Stereo Mini)

This is where you connect the audio output from your

computer when connected to the COMPUTER 1 in-

put. A commercially available audio cable is required.

2.

COMPUTER 2 Input Connector (Mini D-Sub 15 Pin)

Connect your computer or other analog RGB equip-

ment such as IBM compatible or Macintosh comput-

ers. Use the supplied RGB cable to connect to your

computer.

This connector also supports SCART output signal.

The SCART cable is sold separately.

See page 24 for more details.

NOTE: The COMPUTER 2 Input does not support Plug &

Play.

COMPUTER 2 AUDIO Input Mini Jack (Stereo Mini)

This is where you connect the audio output from your

computer when connected to the COMPUTER 2 in-

put. A commercially available audio cable is required.

3. MONITOR OUT Connector (Mini D-Sub 15 Pin)

You can use this connector to loop your computer

image to an external monitor from the COMPUTER

1/2 or component video input source.

This connector also outputs a COMPUTER signal

or component signal in Idle mode.

AUDIO OUT Mini Jack (Stereo Mini)

You can use this jack to output sound from the cur-

rently selected source (COMPUTER 1/2, COMPO-

NENT, VIDEO or S-VIDEO). The current or last dis-

played source's audio will be sent to the audio output

even in Idle mode.

Output sound level (volume, bass/treble and mute)

can be adjusted in accordance with the sound level

of the internal speaker.

Output sound level (volume, bass/treble and mute)

cannot be adjusted in Idle mode.

Note that this cannot be used as a headphone jack.

(When audio equipment is connected, the projector

speaker is disabled.)

4. COMPONENT (Y, Cb/Pb, Cr/Pr) Input Connectors

(RCA)

Connect component video outputs (Y/Cb/Cr, Y/Pb/Pr)

of the external equipment such as DVD player.

NOTE: The “Y” connector accepts Video signal.

COMPONENT AUDIO Input Jacks R/L (RCA)

These are your left and right channel audio inputs for

stereo sound from your DVD player or component

equipment connected to COMPONENT Input Connec-

tors.

5. VIDEO Input Connector (RCA)

Connect a VCR, DVD player, laser disc player, or docu-

ment camera here to project video.

VIDEO/S-VIDEO AUDIO Input Jacks R/L (RCA)

These are your left and right channel audio inputs for

stereo sound from a Video or S-Video source.

16

1. Introduction

Te r minal Panel Features

COMPONENT

Y Cb/Pb Cr/Pr

AUDIO

L/MONO

S-VIDEO

COMPUTER 1AUDIO

PC CARD

USB(COMPUTER)

USB(MOUSE)

MONITOR OUT

COMPUTER 2

PC CONTROL

R

L/MONOVIDEO R

78

10

69

11

6. S-VIDEO Input Connector (Mini DIN 4 Pin)

Here is where you connect the S-Video input from an

external source like a VCR.

NOTE: S-Video provides more vivid color and higher

resolution than the traditional composite video format.

7. USB (MOUSE) Port (Type A)

Connect a commercially available USB mouse. You

can operate the menu or Viewer with the USB mouse

via this port.

8. USB (COMPUTER) Port (Type B)

Connect this port to the USB port (type A) of your PC

using the supplied USB cable. You can operate your

computer's mouse functions from the remote control.

9. PC CONTROL Port (D-Sub 9 Pin)

Use this port to connect your PC to control your pro-

jector via a serial cable. This enables you to use your

PC and serial communication protocol to control the

projector. A commercially available RS232C cross

cable is required to use this port. You can also control

the projector by using Dynamic Image Utility 2.0 in-

cluded on the supplied CD-ROM.

To do so you must first have Dynamic Image Utility

2.0 installed on your PC. If you are writing your own

program, typical PC control codes are on page 121.

10. PC CARD Slot

Insert a PC card here.

11. PC CARD Eject Button

Press to partially eject a PC card partially.

17

1. Introduction

 Part Names of the Remote Control

NOTE: If you are using a Macintosh computer, you can click

either the CANCEL (right-click) or ENTER (left-click) button to

activate the mouse.

1. Infrared Transmitter

Direct the remote control toward the remote sensor

on the projector cabinet.

2. LED

Flashes when any button is pressed.

3. POWER ON Button

When the main power is on, you can use this button

to turn your projector on.

NOTE: To turn on the projector, press and hold the POWER ON

button for a minimum of two seconds.

4. POWER OFF Button

You can use this button to turn your projector off.

NOTE: To turn off the projector, press and hold the POWER

OFF button for a minimum of two seconds.

SOURCE

FREEZE

VIEWER

3D REFORM

ASPECT

HELP

PICTURE

PIC-MUTE

POINTER

VOLUME MAGNIFY

SLIDE

PJ

OFF

12

VIDEO

S-VIDEO

AUTO ADJ.

COMPUTER

COMPONENT

ON

SELECT

POWER

M

E

N

U

E

N

T

E

R

C

A

N

C

E

L

1

2

4

5

6

7

11

13

3

10

8

9

14

12

5. VIDEO Button

Press this button to select a video source from a VCR,

DVD player, laser disc player or document camera.

6. S-VIDEO Button

Press this button to select an S-Video source from a

VCR.

7. COMPUTER 1 Button

Press this button to select COMPUTER 1 input.

8. COMPUTER 2 Button

Press this button to select COMPUTER 2 input.

9. AUTO ADJ. Button

Use this button to adjust an RGB source for an opti-

mal picture. See page 37.

10. COMPONENT Button

Press this button to select a video source from com-

ponent equipment connected to your COMPONENT

input.

11. MENU Button

Displays the menu for various settings and adjust-

ments.

12. SELECT 왖왔왗왘 (Mouse) Button

When you are in the Computer mode, these buttons

work as a computer mouse.

When you are in the Projector mode, which is indi-

cated by lighting the PJ button. See page 40.

왖왔 : Use these buttons to select the menu of the

item you wish to adjust.

왗왘 : Use these buttons to change the level of a se-

lected menu item. A press of the 왘 button ex-

ecutes the selection. When no menus appear,

these buttons work as a volume control.

When an image is magnified, the SELECT 왖왔왗왘

button moves the image.

13. ENTER (Left Click) Button

When you are in the Computer mode, this button works

as the mouse left button. When this button is pressed

and held for a minimum of 2 seconds, the drag mode

is set. When you are in the Projector mode, which is

indicated by lighting the PJ button: Use this button to

enter your menu selection. It works the same way as

the ENTER button on the cabinet. See page 40.

14. CANCEL (Right Click) Button

When you are in the Computer mode, this button works

as the mouse right button. When you are in the Pro-

jector mode, which is indicated by lighting the PJ but-

ton: It works the same way as the CANCEL button on

the cabinet. See page 40.

18

15. PJ Button

Press this button to switch the SELECT, CANCEL, and

ENTER buttons between the Projector mode (lit red)

and the Computer mode.

Press this button or any one of the POWER ON/OFF,

MENU, 3D REFORM, ASPECT, POINTER, HELP,

MAGNIFY, VIEWER or PICTURE buttons to switch to

the Projector mode and the PJ button lights red. To

switch back to the Computer mode, press the PJ but-

ton again. See page 40.

16. 3D REFORM Button

Press this button to enter 3D Reform to correct the

keystone (trapezoidal) distortion, and make the im-

age square. See pages 35 and 44.

17. SOURCE Button

Use this button to select a video source such as a PC,

VCR, DVD player or Viewer (PC card).

Press and release this button quickly to display the

Source List.

Each time this button is pressed for a minimum of ONE

second, the input source will change as follows:

Computer1 → Computer2 → Component → Video →

S-Video → Viewer → Entry List → Computer1 → ...

If no input signal is present, the input will be skipped.

M

E

N

U

E

N

T

E

R

C

A

N

C

E

L

OFF

12

VIDEO

S-VIDEO

AUTO ADJ.

COMPUTER

COMPONENT

ON

SELECT

POWER

PJ

SOURCE

FREEZE

VIEWER

3D REFORM

ASPECT

HELP

PICTURE

PIC-MUTE

POINTER

VOLUME MAGNIFY

SLIDE

16

18

17

24

25

21

26

27

15

19

20

22

23

18. ASPECT Button

Press this button to display the Aspect Ratio select

screen. See page 82.

19. POINTER Button

Press this button to display one of the nine pointers;

press again to hide the pointer. You can move your

pointer icon to the area you want on the screen using

the SELECT 왖왔왗왘 button. See page 41.

20. VOLUME (+)(–) Button

Press (+) to increase the volume and (–) to decrease

it.

21. MAGNIFY (+)(–) Button

Use this button to adjust the image size up to 400%.

The image is magnified about the center of the screen.

See page 41.

22. PICTURE Button

Press this button to display the Picture window. Each

time this button is pressed, the option will be changed.

See page 78.

23. PIC-MUTE Button

This button turns off the image and sound for a short

period of time.

Press again to restore the image and sound.

24. VIEWER Button

Press this button to select the Viewer source.

25. SLIDE (+)(–) Button

Press (+) to select the next folder or slide and (–) to

select the previous folder or slide. See page 58.

26. FREEZE Button

This button will freeze a picture. Press again to re-

sume motion.

27. HELP Button

Provides suitable HELP information.

NOTE: The default is the Computer mode, which allows you to

use the SELECT, CANCEL, and ENTER buttons as your computer

mouse. When the POWER ON/OFF, MENU, 3D REFORM, AS-

PECT, POINTER, HELP, MAGNIFY, VIEWER or PICTURE button

is pressed, the PJ button lights red to indicate that you are in the

Projector mode. If no buttons are pressed within 60 seconds,

the light goes out and the Projector mode is canceled.

1. Introduction

19

1. Introduction

30°

Note on Remote Control Operation

If you press and hold the SELECT 왖왔왗왘 button while installing new batteries, the remote control may fail to work

properly.

Should this happen, remove the batteries and then install them again without touching the SELECT button.

Remote Control Precautions

• Handle the remote control carefully.

• If the remote control gets wet, wipe it dry immediately.

•Avoid excessive heat and humidity.

• If you will not be using the remote control for a long time, remove the batteries.

• Do not place the batteries upside down.

• Do not use new and old batteries together, or use different types of batteries together.

Operating Range for Wireless Remote Control

Battery Installation

1

Remove the battery cover.

2

Remove both old batteries and in-

stall new ones (AA). Ensure that

you have the batteries' polarity (+/

-) aligned correctly.

3

Slip the cover back over the bat-

teries until it snaps into place. Do

not mix different types of batter-

ies or new and old batteries.

Remote sensor on projector cabinet

Remote control

7m/22 feet

• The infrared signal operates by line-of-sight up to a distance of about 22 feet/7 m and within a 60-degree angle of

the remote sensor on the projector cabinet.

• The projector will not respond if there are objects between the remote control and the sensor, or if strong light falls

on the sensor.

Weak batteries will also prevent the remote control from properly operating the projector.

20

2

Installation and Connections

 Setting Up the Screen and the Projector ................... 21

Selecting a Location ............................................................................................. 21

Throw Distance and Screen Size ......................................................................... 22

 Making Connections .................................................. 23

Enabling the computer’s external display ............................................................. 23

Connecting Your PC or Macintosh Computer ....................................................... 23

To connect SCART output (RGB) ......................................................................... 24

Connecting an External Monitor ........................................................................... 25

Connecting Your DVD Player with Component Output ......................................... 26

Connecting Your VCR or Laser Disc Player .......................................................... 27

Connecting the Supplied Power Cable ................................................................. 28

Page is loading ...

NEC vt 770, VT770 Owner's manual

Related papers

Other documents