Miller KA000000 Owner's manual
- Category
- Multimedia carts & stands
- Type
- Owner's manual
This manual is also suitable for
December 1990 FORFORM:
Use above FORM number when ordering extra manuals.
OWNER’S MANUAL
OM-678A
Running Gear/Economy Cart 134 505
The data contained in this supplement is either in addition to or takes exception to data appearing
later in this manual.
A. Assembly Instructions (Figure 1)
1. Insert axle (6) through holes in running gear shelf (5).
2. Install wheels (4) onto axle with supplied retaining rings (7).
3. Install casters (10) with supplied lock washers (9) and nuts (8).
4. Install handle assembly (1) with supplied hardware (11, 12, and 13).
5. Insert gun holder insulator (2) into gun holder on handle assembly and secure with supplied springrip locking
washer (3).
B. Installation Of XMT Models Onto Running Gear/Economy Cart
WARNING: ELECTRIC SHOCK can kill.
• Do not touch live electrical parts.
• Disconnect input power conductors from deenergized supply line BEFORE moving welding power
source.
FALLING EQUIPMENT can cause serious personal injury and equipment damage.
• Lift unit at handles on top ends of case.
• Have two persons of adequate physical strength lift unit.
• Move unit with hand cart or similar device of adequate capacity.
• Use equipment of adequate capacity to lift the unit.
• If using a fork lift vehicle, place and secure unit on a proper skid before transporting.
This unit has built-in handles on top ends of case for lifting. Be sure unit is lifted and transported safely and
securely.
1. Unthread and remove the four rubber mounting pads on the bottom of the XMT unit.
2. Partially thread two of the supplied .312-18 x 1.000 in. screws into the XMT unit rear mounting holes where the
rubber mounting pads were removed in Step 1.
3. Carefully position the XMT unit on the inclined portion of the running gear so that the front control panel faces
upwards, and the two mounting screws on the XMT unit fit into the matching slotted holes on the running gear
shelf. Make sure that the screws slide down into the slots.
4. Thread two other supplied .312-18 x 1.000 in. screws from the bottom of the running gear shelf through the
running gear mounting holes and into the two remaining XMT unit mounting holes.
5. Tighten all four screws.
C. Installation Of MAXTRON Models Onto Running Gear/Economy Cart
WARNING: ELECTRIC SHOCK can kill.
• Do not touch live electrical parts.
• Disconnect input power conductors from deenergized supply line BEFORE moving welding power
source.
FALLING EQUIPMENT can cause serious personal injury and equipment damage.
• Use lifting eye to lift unit only, NOT running gear, gas cylinders, or any other heavy accessories or devices.
• Use equipment of adequate capacity to lift the unit.
• If lifting or moving this unit with lift forks under the base, be sure that lift forks are long enough to extend
beyond opposite side of the base.
Using lift forks too short can damage internal parts if tips of the lift forks penetrate the unit base, or may cause
personal injury and/or equipment damage if unit falls off the lift forks.
OM-678 Page 2
1. Carefully position the MAXTRON unit on the inclined portion of the running gear so that the front control panel
faces upwards and the MAXTRON and running gear mounting holes align.
2. Secure with supplied .250-20 x .500 in. bolts, lockwashers, and nuts.
SC-137 344-A
123
4
5
6
7
8910111213
Figure 1. Running Gear/Economy Cart
Description Quantity
Part
No.
Figure 1. Running Gear/Economy Cart134 505
Item
No.
1 142 312 HANDLE ASSEMBLY 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2 090 099 INSULATOR, gun holder 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3 044 800 WASHER, springrip locking for .750 shaft 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4 090 693 WHEEL, rubolene spoke 8 in x 2.000 wide x .760 bore 2. . . . . . . . . . . . . . . . . . . .
5 142 315 SHELF, running gear 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6 020 824 AXLE, (consisting of) 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7 121 614 · RING, retaining ext .750 shaft x .085 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8 601 879 NUT, stl hex full fnsh .500-13 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9 602 216 WASHER, lock stl split .500 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10 137 077 CASTER, rbr swvl 3dia .500-13 x .750 stem 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11 602 207 WASHER, lock stl split .250 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12 601 865 NUT, stl hex full fnsh .250-20 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
13 108 942 SCREW, cap stl hexwhd .250-20 x 1.250 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Hardware For Mounting Welding Power Sources
088 366 SCREW, cap stl hexwhd slflkg .312-18 x 1.000 (XMT Models) 4. . . . . . . . . . . . . .
089 799 SCREW, cap stl hexwhd .250-20 x .500 (Maxtron Models) 4. . . . . . . . . . . . . . . . .
602 207 WASHER, lock stl split .250 (Maxtron Models) 4. . . . . . . . . . . . . . . . . . . . . . . . . . . .
601 865 NUT, stl hex full fnsh .250-20 (Maxtron Models) 4. . . . . . . . . . . . . . . . . . . . . . . . . . .
BE SURE TO PROVIDE MODEL WHEN ORDERING REPLACEMENT PARTS.
-
1
-
2
Miller KA000000 Owner's manual
- Category
- Multimedia carts & stands
- Type
- Owner's manual
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Miller KA000000 Owner's manual
-
Miller KC000000 Owner's manual
-
-
-
-
-
Miller KB000000 Owner's manual
-
-
-