CyberData 011272 Owner's manual

Category
Door intercom systems
Type
Owner's manual

CyberData 011272 is a SIP compliant indoor intercom with intrusion sensor function, designed for flush mount installation. It features a 2-gang box mounting, PoE connectivity, and a network cable assembly for easy installation. The intercom supports DHCP for automatic IP addressing and has a default IP address of 10.10.10.10. It also includes a web access interface with default username and password of "admin". Additionally, the intercom has a RTFM button for announcing its IP address or restoring factory default settings.

CyberData 011272 is a SIP compliant indoor intercom with intrusion sensor function, designed for flush mount installation. It features a 2-gang box mounting, PoE connectivity, and a network cable assembly for easy installation. The intercom supports DHCP for automatic IP addressing and has a default IP address of 10.10.10.10. It also includes a web access interface with default username and password of "admin". Additionally, the intercom has a RTFM button for announcing its IP address or restoring factory default settings.

Quick Reference 930784H © 2017, CyberData Corporation, ALL RIGHTS RESERVED© 2017, CyberData Corporation, ALL RIGHTS RESERVED 930784H Quick Reference
Mounting Options
Contacting CyberData
Fold Down All Flagnuts
before Inserting into Wall Cutout
Cutout
Network Cable Assembly
(Not Provided)
Screws
Faceplate
2 Gang Box
Torx Drive)
Assembly
Points Upward,
Arrow Labels Must
This will Ensure
Intrusion Sensor
Function Properly
Wall
Inside Gangbox
Create Service Loop
Torx Key
(Phillip Drive)
(Security
Mounting
Screws
Mounting
Flagnuts
(4 Places)
K.O.
to J1
6.03 inches
[153mm]
5.28 inches
[134mm]
Network Cable
J1
To mount the Intercom:
1. Make a wall cutout as shown in the picture.
2. Use a flat blade screwdriver to remove the knockout (KO) of the gang box.
3. Feed the ground wire (shown in the “Ground Connection” section) and the network cable from the wall cutout through the
knockout hole of the gang box.
4. Create a service loop for both the ground wire and network cable.
5. Plug the network cable into the J1 connector.
6. Make sure that the arrow labels on the sides of the gang box are pointing up. This will ensure that the intrusion sensor
functions properly.
7. Fold down all of the flagnuts, and then insert the gang box into the wall cutout.
8. Tighten the flagnuts with a size #2 Phillips screwdriver.
9. Use a size #2 Phillips screwdriver to secure the Intercom faceplate assembly to the gang box with either Phillips drive
screws or security Torx drive screws.
Sales: (831) 373-2601 ext. 334
Support: 831-373-2601 ext. 333
Support Website: http://support.cyberdata.net/
RMA Department: (831) 373-2601 ext. 136
RMA Status: http://support.cyberdata.net/
Warranty Information: http://support.cyberdata.net/
Corporate Headquarters
CyberData Corporation
3 Justin Court
Monterey, CA 93940, USA
Phone: 831-373-2601
Fax: 831-373-4193
http://www.cyberdata.net/
Typical System Installation
Getting Started
Download the Operations Guide PDF file, from the Downloads tab at the following webpage:
http://www.cyberdata.net/voip/011272/
Create a plan for the locations of your Intercoms.
WARNING: This product should be installed by a licensed electrician according to all local electrical and building codes.
WARNING: To prevent injury, this apparatus must be securely attached to the floor/wall in accordance with the installation
instructions.
WARNING: The PoE connector is intended for intra-building connections only and does not route to the outside plant.
WARNING: This enclosure is not rated for any AC voltages!
Intercom Parts
Tool required for assembly: A size #2 Phillips screwdriver
Parameter Factory Default Setting
IP Addressing DHCP
IP Address
a
10.10.10.10
Web Access Username admin
Web Access Password admin
Subnet Mask
a
255.0.0.0
Default Gateway
a
10.0.0.1
a. Default if there is not a DHCP server present.
802.3af Compliant Ethernet Switch
Intercom IP Phone IP PBX ServerIntercom Intercom
*More installation and mounting
options are available in the
Operations Guide.
(4) #6 X 3/8-inch,100 Deg.,
Flat Head, Self-Tapping Screw
(1) Intercom Assembly (1) Mounting Kit
(4) #6 X 3/8-inch,100 Deg.,
Flat Head T15 Security Pin Torx
Screw
(1) T15 Security Pin Torx Key
(1) Optional Mounting Kit
The IP Endpoint Company
Installation Quick Reference
SIP Indoor Intercom Flush Mount
SIP Compliant
011272
© 2017, CyberData Corporation, ALL RIGHTS RESERVED 930784H Quick Reference Quick Reference 930784H © 2017, CyberData Corporation, ALL RIGHTS RESERVED
RTFM Button
Ground Connection
RTFM button (SW1)
When the device is operational and linked to a network,
you can use the Reset Test Function Management
(RTFM) button (SW1 [see picture]) to announce the
device’s IP address or restore the device to the factory
default settings.
To announce the device’s current IP address:
Press and release the RTFM button within a five
second window.
Note The device will use DHCP to obtain the new IP
address (DHCP-assigned address or default to
10.10.10.10 if a DHCP server is not present).
To restore the device to factory default settings:
Press and hold the RTFM button for longer than five
seconds until you hear the device announce that it is
restoring the factory default settings.
inside Gang Box
Create Service Loop
Knock Out
Star Washer
#6 Ring Terminal
Nut
Ground Lug
(Not Provided)
Ground Wire Assembly
Dimensions
Terminal Block Connections
6.840 [173.7]
Dimensions are in Inches [Millimeter]
2.419 [61.4]
5.860 [148.8]
0.170 [4.3]
0.25"
Terminal Block
Wire (IN)
can accept 16 AWG wire
1
8
Alternate Power Input:
1 = +8 to +12VDC @ 1000mA Regulated Power Supply*
2 = Power Ground*
Relay Contact:
(1 A at 30 VDC for continuous loads)
3 = Relay Common
4 = Relay Normally Open Contact
5 = Sense Input
6 = Sense Ground
7 = Remote Switch "A"
8 = Remote Switch "B"
*Contacts 1 and 2 on the terminal block are only for
powering the device from a non-PoE 12VDC power
source as an alternative to Network PoE power. Use of
these contacts for any other purpose will damage the
device and void the product warranty.
Use a 3.17 mm (1/8-inch) flat blade
screwdriver for the terminal block screws
  • Page 1 1
  • Page 2 2

CyberData 011272 Owner's manual

Category
Door intercom systems
Type
Owner's manual

CyberData 011272 is a SIP compliant indoor intercom with intrusion sensor function, designed for flush mount installation. It features a 2-gang box mounting, PoE connectivity, and a network cable assembly for easy installation. The intercom supports DHCP for automatic IP addressing and has a default IP address of 10.10.10.10. It also includes a web access interface with default username and password of "admin". Additionally, the intercom has a RTFM button for announcing its IP address or restoring factory default settings.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI