Montigo H38SVOST Outdoor Enclosure Operating instructions

Category
Fireplaces
Type
Operating instructions

This manual is also suitable for

XT0064 - 170920
Installation
ENSURE THAT ALL PROTECTIVE FILM FROM METAL PARTS IS REMOVED
BEFORE ASSEMBLY
PART ID# DESCRIPTION QUANT.
1 O38ST060 BRACKET TOP SUPPORT, H38 2
2 O38ST059 BRACKET,H38 ENCL. 4
3 O38ST058 BASE, H38ST, ENCLOSURE 1
4 O38ST054 Fan Bracket 2
5 O38ST017 SIDE SKINS H38 2
6 O38ST016 TOP COVER 1
7 HW2212 VELCRO, 1"x2.75" MATED HOOK/LOOP 2
8 HW2105 SCREW, PAN, #10-24 X 1/2", PHIL, SS 28
9 HW1161 #10 Nutsert 20
10 EC1472 Fans 2
H38SVOBE OUTDOOR ENCLOSURE
For outdoor use only
NOTE: This installation of this unit requires electrical mains power
connection and must be done by a qualied electrician and certied
gas appliance installer
Check local codes and read all instructions prior to installation.
Route gas and electrical lines before construction and installation of
the enclosure
The enclosure features venting holes underneath the top cover,
ensure these are not covered
WARNING
Assembly
1
3
4
6
7
8
2
Place the 2 PART №1 Top support brackets on the top
of the unit using the supplied pan head screws.
The top of PART5 Side Skins (4) are attached to the
replace using supplied Pan head screws.
PART №6 Top cover is secured to the top of the Side
skins with 4 Pan Head screws on each side as shown.
PART №10 EC1472 Fan kits are inserted and attached to
the inside floor of the unit using PART №7 Velcro strips.
fans should sit against the inside side wall of the unit.
The bottom of PART5 Side Skins (4) are attached to the
replace using supplied Pan head screws. Valve blind may
need to be removed to access holes. Repeat other side.
Fans are wired into the control box as per below
schematic.
Place unit on PART №3 Base and attach with 4 PART №2
Brackets using the supplied pan head screws.
See installation manual for instructions on how to route gas lines
and power supply
See installation manual for clearances to combustible materials
Plan a proper drainage system before installation of the enclosure
U
X
U
X
U
X
FINISHED DIMENSIONS
H38STVOBE ENCLOSURE
NAME
CHECKED
DRAWN
THIRD ANGLE PROJECTION
DATE
FRACTIONAL
X.XX
X.XXX
ANGULAR:
DIM ARE IN INCHES
UNLESS OTHERWISE SPECIFIED
ALL BENDS ARE 90
1/8
.015
.005
1
41"
44 3/8"
43"
25 3/4"
27 3/4"
1 1/2"
1:20
DWG. NO.
REV.
1 OF 3
A
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF CANADIAN HEATING PRODUCTS. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF CANADIAN HEATING PRODUCTS IS PROHIBITED.
PROPRIETARY AND CONFIDENTIAL
Wednesday, February 21, 2018 12:16:50 PM
SCALE:
ENCLOSURE, H38 OUTDOOR, SEE
THRU
H38VOBE
SHEET:
SIZE
A
CF
2/19/2018
CF
2/19/2018
Y:\CADD\H-UNITS\H38\OD38ST\Enclosure\H38VOBE
X
Q
U
X
U
S
X
Q
X
X
R
X
3
8
8
8
8
5
8
5
1
8
6
2
120 Volt
24 Volt
Transformer
120V in
Gas Valve Connection
24V
Electrical
Box
Fans
Divider
Black
Black
Red
Red
Black
White
Black
X2
White
X2
White
X2
A A
B B
2
2
1
1
DO NOT SCALE DRAWING
H38 Electrical Schematic
SHEET 1 OF 1
UNLESS OTHERWISE SPECIFIED:
SCALE: 1:1
WEIGHT:
REV
DWG. NO.
A
SIZE
TITLE:
NAME
DATE
COMMENTS:
Q.A.
MFG APPR.
ENG APPR.
CHECKED
DRAWN
FINISH
MATERIAL
INTERPRET GEOMETRIC
TOLERANCING PER:
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
ANGULAR: MACH
BEND
TWO PLACE DECIMAL
THREE PLACE DECIMAL
APPLICATION
USED ON
NEXT ASSY
PROPRIETARY AND CONFIDENTIAL
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
<INSERT COMPANY NAME HERE>. ANY
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
<INSERT COMPANY NAME HERE> IS
PROHIBITED.
X
Q
Air channel plates must
be removed at this point
of installation
(both sides)
Some materials used in the manufacturing process of this product can
expose you to Benzene which is known in the State of California to
cause cancer and birth defects or other reproductive harm. For more
information go to www.P65warnings.ca.gov
WARNING
  • Page 1 1

Montigo H38SVOST Outdoor Enclosure Operating instructions

Category
Fireplaces
Type
Operating instructions
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI