Moultrie MFG-13455 Operating instructions

Type
Operating instructions

Moultrie MFG-13455 Super Pro Magnum Feeder: Automate your wildlife feeding with this versatile feeder kit, compatible with any drum or barrel. It features a 2.25" hole for easy filling, a grooved handle for secure battery cover attachment, and adjustable leg poles for stability. Set up to 10 feed times, each lasting 1-60 seconds, and choose specific days of the week for each feeding. The feeder's motor speed is also adjustable for customized feeding.

Moultrie MFG-13455 Super Pro Magnum Feeder: Automate your wildlife feeding with this versatile feeder kit, compatible with any drum or barrel. It features a 2.25" hole for easy filling, a grooved handle for secure battery cover attachment, and adjustable leg poles for stability. Set up to 10 feed times, each lasting 1-60 seconds, and choose specific days of the week for each feeding. The feeder's motor speed is also adjustable for customized feeding.

Instructions for Super Pro Magnum Feeder
Thank you for your purchase of the Super Pro Magnum Feeder. Please read this sheet
before
operating the unit. If you should have any questions about this product or any other
Moultrie
product, please contact us using the information on the back of this sheet.
DRILLING YOUR DRUM OR BARREL
A
MOUNTING THE FEEDER
B
Turn drum over, measure and mark the center of the bottom.
Mark where holes of kit are on the bottom of the drum.
Drill three 5/16” Feeder Leg Holes.
Using a Hole Saw, drill a 2.25” hole in the center of the
bottom of your drum.
From the inside of the drum, put at washers on the 1/4-20 x 4”
Combination Drive Screws then slide through the holes in the
bottom of the barrel and screw the push nuts onto the bolts on
the outside of the barrel.
Slide feeder over three Bolts that are sticking rmly through
the bottom of the drum. Attach Feeder Kit to the Drum
using the three provided Wing Nuts.
Super Pro Magnum Kit will mount to the bottom of any drum or barrel
NOTE: If you purchased a Moultrie barrel, go to Step B
Combination Drive Screw
Qty. 3
(¼”-20 x 4”)
Flat Washer
Qty. 3
(¼”)
Push Nut
Qty. 3
(¼”)
Wing Nut
Qty. 3
(¼”)
HARDWARE INCLUDED:
Push Nut
Combination
Drive Screw
Turn grooved handle counterclockwise one click . This will release
the battery cover from the feeder kit. Battery cover can be pulled
o straight downward and set aside.
NOTE: Grooved handle
should stay assembled with battery cover.
DO NOT FORCE THE GROOVED HANDLE COUNTERCLOCKWISE
AN ADDITIONAL CLICK.
This will disassemble the grooved handle
from the battery cover and can cause wear on the parts that
retain this assembly.
Bolts
Super Pro Magnum
Feeder Kit
Wing Nuts
Drum
Flat Washer
O
F
F
O
N
INSTALLING BATTERY
C
CAUTION: WEAR EYE PROTECTION
SET
UP DOWN
SET
UP DOWN
SET TIME OF DAY: Press the UP or DOWN button until the correct time of day appears.
Press and release button to single-step through the minutes or hold down to advance quickly.
The feeder will not run while buttons are being pressed and waits 10 seconds from the last
button press before it is activated. The feeder is activated when the display alternates between
the CURRENT TIME and %BATTERY.
SET FEED TIMES: Press the SET button until the
correct Timer Number appears in the upper right hand
corner as shown. Press the UP or DOWN button to set
the Feed Time.
SET RUN DURATION: Press the SET button again
to set the RUN-TIME SECONDS which can range
from zero to twenty seconds. Adjust RUN-TIME
SECONDS using the chart below. Set the RUN-TIME
SECONDS to zero to disable the feed time.
TEST TIMER: To test the Timer, PRESS AND HOLD
the SET button while the RUN-TIME SECONDS are
displayed. Release the button and get away from the
feeder when the message “TESTING GET AWAY”
appears on the display. The display will countdown five
seconds before activating the motor for the number of
RUN-TIME SECONDS programmed. The test feature is
useful for assessing the amount of feed to dispense.
SET
UP DOWN
SET
UP DOWN
SET
UP DOWN
SET
UP DOWN
6:00pm for six seconds. To change the factory settings or add additional feed times, follow the
instructions below. The Battery Level is displayed every seven seconds. It is recommended that the
battery be replaced when the %BATTERY reading is 25% or below.
8:00
SET TIMER
3
AM
:06
SET TIMER
3
RUN-TIME
SECONDS
:05
TESTING GET AWAY
RUN-TIME SECONDS
Approx. feed dispensed (lbs.)
4 6 8 10 12 14 16 18
.75 1 1.5 2 2.5 3 3.5 4
NOTE: This equipment has been tested and found to comply with the limits of Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
NOTE: Be sure that the Red and Black alligator clips labeled with a “1” are
both attached to the appropriate terminals on the rst battery, and that
the Red and Black alligator clips labeled with a “2” are both attached to
the appropriate terminals on the second battery (if used).
Make sure grooved handle is in the counterclockwise position,
then slide the battery cover back onto the assembly. Make sure
the design features line up with the features on the feeder kit.
Once fully in place, rotate the grooved handle one click in the
clockwise direction to secure all pieces in place.
NOTE: Make sure grooved handle is rotated
counter-clockwise before trying to install
battery housing or else it will not lock into place.
STAND UP FEEDER AND INSTALL LID
D
Assemble leg poles with the desired amount of leg sections.
Tap legs into place during assembly.
With two legs against the ground, rotate feeder upward until
vertical and supported by all three legs.
Add feed, then install lid and tighten bolt securely.
Leg Section
Leg Pole
Square Leg
Brackets
DO NOT EXCEED 400 LBS
OF FEED IN 55-GAL FEEDERS
DO NOT EXCEED 200 LBS
OF FEED IN 30-GAL FEEDERS
Install one or two 6-volt alkaline (ex. Energizer™) or Moultrie rechargeable batteries by attaching the Red Alligator Clip
to the postitive terminal (+) and the Black Alligator Clip to the negative (-) terminal.
O
F
F
O
N
Super Pro Magnum
Feeder Kit
Belly Band
Ring
Bolt
Spacer
Lock
Washer
Nut
NOTE: DO NOT LOAD FEEDER until it is standing up and in place (see Section D).
Belly Band
Ring
Slide the bolt through the Belly Band Ring, Spacer and
Lock Washer as shown. Tighten nut on bolt until metal
Belly Band Ring tabs are touching spacer on each side.
Turn the Metal Drum upside down and slide the Belly Band Ring
around perimeter and make sure that belly band is snug against
the bottom structure ring as shown (Moultrie barrel only).
CONFIGURING AND TESTING FEEDER
E
SET CURRENT TIME: Press the PROGRAM button and SET CURRENT TIME will appear. Press UP or DOWN to set the
hour, then press RIGHT to go to the minutes. Press UP or DOWN to set the minutes. Press the BACK button to return
to the Main Menu , or press PROGRAM to proceed through the settings.
NOTE: The timer is capable up to 10 feed times, each 1-60 seconds each, and each can operate on any day of
the week where each day can be toggled ON/OFF.
SET CURRENT DAY: Press the PROGRAM button until the Set Current Day screen appears. Press LEFT or RIGHT to
select the current day. Press BACK to return to the Main Menu, or press PROGRAM to proceed through the settings.
SET EST. FEED REMAINING: Press the PROGRAM button until the Est. Feed Remaining screen appears. Press UP or
DOWN to select the amount of feed you have in the feeder. Press BACK to return to the Main Menu, or press
PROGRAM to proceed through the settings.
SET FEED TIME: Press the PROGRAM button until the desired Feed Timer appears at the top of the screen. Press the
DOWN button until the feed time is ashing. Press PROGRAM to enter edit mode. Press UP or DOWN to set the hour.
Press the RIGHT button to go over to the minutes. Press UP or DOWN to set the minutes. Press PROGRAM or BACK to
return to the Feed Timer. The factory settings include two feeder times 7am and 6pm, each for 6 seconds.
SET DAYS OF THE WEEK: After setting the feed time, press UP so the days of the week start ashing. Press PROGRAM
to enter edit mode. By default all days should be enabled. Press LEFT or RIGHT to highlight the desired day. Press
DOWN to disable the selected day. Press UP to re-enable the selected day. Once all desired days are selected, press
PROGRAM or BACK to return to the Feed Timer.
SET RUN DURATION: Press DOWN and LEFT until the RUN DURATION seconds are ashing. Press PROGRAM to enter
edit mode. Press UP or DOWN to set desired feed duration. Press PROGRAM or BACK to return to the Feed Timer. 
SET MOTOR SPEED: Press UP or DOWN until the motor speed setting is ashing at the bottom of the screen. Press
PROGRAM to enter edit mode. Press RIGHT or LEFT to select the desired motor setting. Press PROGRAM or BACK to
return to the Feed Timer.
When the Feed Timer is blinking at the top of the screen, press PROGRAM or RIGHT to advance to the next feed
timer. Repeat for all required feed times.
TEST FEEDER: Press the BACK button to reach the Main Menu. Press the TEST button to enter the Test Mode. The
Test duration will appear (this will be the same as the duration as Feed Timer 1). Press UP or DOWN to set the Test
Duration. Press PROGRAM. Press RIGHT or LEFT to select desired motor speed. Press PROGRAM to perform test.
After a 5 second countdown, the test will commence. 
Full Battery
Empty Battery
04192022 / MFG-13455
Our Service Department will gladly answer any questions you have.
www.moultriefeeders.com/support
Helpful Tips:
– For extended battery life, the Moultrie 6V Feeder/Micro Camer Power Panel (MFA-15029) or Feeder PowerPanel (MFA-12602) can be added using the
External Power Port.
– Replacement parts can be purchased from Moultrie’s website www.moultriefeeders.com.
– Your Moultrie Super Pro Magnum Feeder Kit has a Lifetime Warranty. Please visit www.moultriefeeders.com/support for more information.
FCC COMPLIANCE
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
For devices approved under Part 15, the user’s manual or instruction manual for an intentional or unintentional radiator shall caution the user about changes or modications to the device (Section 15.21).
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
  • Page 1 1
  • Page 2 2
  • Page 3 3

Moultrie MFG-13455 Operating instructions

Type
Operating instructions

Moultrie MFG-13455 Super Pro Magnum Feeder: Automate your wildlife feeding with this versatile feeder kit, compatible with any drum or barrel. It features a 2.25" hole for easy filling, a grooved handle for secure battery cover attachment, and adjustable leg poles for stability. Set up to 10 feed times, each lasting 1-60 seconds, and choose specific days of the week for each feeding. The feeder's motor speed is also adjustable for customized feeding.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI