Page is loading ...
PANGE~
A LI D D
•
~
VULCAN
~
~
WALL
MOUNTED
TURNTABLE
SHELF
PREMIER
SE
MKII
PANGE.A:
A U D I D
AN
AMERICAN
COMPANY
2023 © PANGEA AUDIO
PGWMSS
E2
Included
Parts
NO. DESCRIPTION
A M8x25
~
8 M6x12
@1l»»
C
MB
<Jy»m»
D 8#x50
01111111m11mmm111>
E M6 g
F
~
G
~
H
~
I
MS
~
J M4
~
K
13mm~10mm
L
~
M E -
--?
.....,
N £
0
~
Step 1
QTY
2
2
4
8
2
8
8
8
1
1
1
1
1
1
1
Tools Needed
-Level
-Electric Drill
-Phillips Screwdriver
-Stud Finder
-Pencil/Pen
-Tape Measure (Optional)
(
I
- - - - '
Use caution
to
avoid electrical wires,
pipes, or any other in-wall hazards
that
cannot be seen through drywall.
If
you
are
unsure before you drill,
call a professional
for
installation.
,
_________
_
@D
@x2
Q)
00
CD
J
Step2
Step
3A
Mounting
on
wall studs (preferred):
1.
Locate and lightly mark wall studs and voids
with a stud finder (not included).
2.
Level (not included) the backplate
(M)
in the desired position against the wall.
3.
Using step
#1
marks
as
a guide,
mark stud locations using backplate
(M)
as
the template.
4.
Use
drill bit
(L)
to drill holes
through the drywall into
the
studs.
5.
Place
screw
(D)
through screw cap
(F).
6.
Put the screw through backplate and
into the drilled hole, while placing
the backplate against the wall.
7.
Hand tighten screw against backplate
until firmly seated (do
not
overtighten).
8.
Snap
screw
cap
(F)
closed.
9.
Repeat for
all
other
mounting
spots.
t))1111il\\iilli\hillili\\
►
© x8
Note: Most studs
are
spaced 16" on center, and
is
the preferred
method
of
mounting.
It
is
recommended that at least four
(4)
screws
are
seated firmly into wooden studs. Mounting only on drywall
is
dangerous,
and reduces the weight capacity
of
the shelf considerably.
The drywall anchors are only supplied to supplement
the
stud-mounted screws.
Wall
..
Step
38
Mounting
on
drywall (only
if
needed):
1. Locate and lightly mark wall studs and voids
with
a stud finder (not included).
2.
Level (not included) the backplate
(M)
in
the desired position against the wall.
3.
Using step
#1
marks
as
a guide,
mark voids for drywall anchors
(G)
using backplate
(M)
as
the template.
4.
Drill into drywall using drill
bit
(L)
to
create a starter hole for
the drywall anchor
(G).
5.
Turn drywall anchor into drywall
with
a Phillips screwdriver until
flush with wall.
6.
Place
screw
(D)
through screw cap
(F).
7.
Put screw through backplate and into
the drywall anchor, while placing the backplate
against the wall.
8.
Hand tighten screw against backplate until
firmly seated (do
not
overtighten).
9.
Snap
screw cap
(F)
closed.
10.
Repeat for all other mounting spots.
Step4
1.
Put shelf
(0)
on spikes, aligning the spikes
with
the
caps
on the underside
of
the shelf.
2.
Level the shelf, left
to
right, and front
to
back,
by adjusting the threaded spikes
(C).
3.
Using wrench
(K),
tighten locknuts.
4.
Place
stickers
(H)
over unused
holes
as
needed.
o
lliilllil\11\11\jjll\\jn
Wall
© x8
For more
products
from
Pangea Audio, visit
WWW.PANGEAAUDIO.COM
~
(E)
x8
/