Supermicro X9SKV Quick Reference Manual
- Category
- Computer cases
- Type
- Quick Reference Manual
S
UPERMICR
R
ContaCt InformatIon
• Website:www.supermicro.com
• GeneralInformation:[email protected]
• TechSupport:[email protected]
• Phone:+1(408)503-8000,Fax:+1(408)503-8008
PaCkage Contents
(Appliestoindividual-packonly)
X9SKV
QuICk referenCe guIde rev. 1.00
• One(1)SupermicroMotherboardwithCPUandHeatsinkInstalled
• Two(2)SATACables
• One(1)I/OShield
• One(1)QuickReferenceGuide
MNL-1539-QRG 1.00
© 2012 Supermicro Computer Inc. All rights reserved. Reproduction of this document whether in part or in whole is strictly prohibited without Supermicro's written
consent. All Trademarks are property of their respective entities. All information provided is deemed accurate at the time of printing; however, it is not guaranteed.
MNL-1539-QRG
for your system to work ProPerly, Please download the aPProPrIate
drIvers/Images/user's manual from the lInks below:
• Manuals:http://www.supermicro.com/support/manuals
• Drivers&Utilities:ftp://ftp.supermicro.com/CDR_Images/CDR-X9-UP/
• Safety:http://www.supermicro.com/about/policies/safety_information.cfm
A
This motherboard supports up to 32 GB of DDR3 ECC SODIMMs
in 4 SODIMM slots. It supports speeds of up to 1600MHz.
Note: For memory optimization, use only SODIMM modules that have been validated by
Supermicro. For the latest memory updates, please refer to our website at http://www.
supermicro.com/products/motherboard.
Jumper Description Settings (Defaults are in Bold)
JPME2 Intel ME Manufacturing Mode
Pins 1-2 (Normal), Pins 1-2 (Intel ME Manuf. Mode)
JPF1 Front Panel LED select
Pins2-3 (Normal), Pins 1-2 (Bypass LAN LED)
JPF2 Front Panel RST Button select Pins2-3 (Normal), Pins 1-2 (FR/NMI)
JBT1 Clear CMOS Short contact pads to clear CMOS
JI2C1/JI2C2 SMB to PCI-Express Slots Pins 1-2 (Open: Disabled), (Closed: Enabled)
JPSLOT1 PCI-E Slot select Pins 1-2 (Slot 7), Pins 2-3 (Slot 6)
Connector Description
Back Panel I/O
Please see "Back Panel IO Connectors" below, left
JSTBY1
Provides 5V standby power only, and legacy Wake-On-LAN function
USB 2/3
Front Panel USB 2.0 header for USB 2/3
USB 4
Internal Type A USB Port
COM2
Serial Port header (COM2)
JF1
Front Panel control header (see Front Panel Control (JF1) below, right)
JF2
Front Panel control header (see Front Panel Control (JF2) below)
FAN1~FAN6
System Fan power/control headers (FAN1: CPU Fan)
JD1
External Speaker/Buzzer header (Pins 1-3: Power LED, Pins 4-7:Ext Speaker)
JOH1
System Overheat header
JL1
Chassis Intrusion header
JWOR1
Wake-On-Ring header
I-SATA0/I-SATA1
3Gb/s I-SATA connectors for SATA0 and SATA1
JSD1
SATA DOM (Disk-On-Module) power connector
SP1
Internal Speaker/Buzzer
JPW1
Motherboard 24-pin ATX Main Power connector
JPW2
Motherboard 8-pin ATX CPU Power connector
JTPM1
Trusted Platform Module (TPM) header
LED Description Color/State Status
LED5 Power LED
Green/Solid System On/Running
Motherboard Layout and Features
Jumpers, Connectors and LED Indicators
Jumpers
Connectors
LED Indicators
Note: Graphics shown in this quick reference guide are for illustration only. Your components may or may not look exactly the same as drawings shown in this guide.
Front Panel Control (JF1)
Memory Population Guidelines
When installing memory modules, the DIMM slots should be populated in the
following order: DIMMA2, DIMMB2 and DIMMA1, DIMMB1
Back Panel I/O Connectors
Memory Support
Note: Refer to Chapter 2 of the User Manual for detailed information on memory support and CPU/
motherboard installation instructions.
DIMM Installation
Note: Refer to Chapter 2 of the User Manual for detailed information on jumpers, connectors, and LED indicators.
= mounting hole
B
C
D
E
F
G
H
I
DIMMA1
Towards the CPU
Towards the edge of the motherboard
DIMMA2
A. LAN1 (Bypass Pair 1)
B. LAN2 (Bypass Pair 1)
C. LAN3 (Bypass Pair 2)
D. LAN4 (Bypass Pair 2)
E. COM1
F. LAN5
G. LAN6
H. USB0 (2.0)
I. USB1 (2.0)
Power Button
1
LAN5 (Link/Activity) LED
Reset Button
2
HDD LED
FP Power LED
3.3V SB
3.3V
3.3V SB
OH/Fan Fail LED
Ground
Ground
1920
Key
Ground
NMI
Key
3.3V SB
LAN6 (Link/Activity) LED
Power Fail
3.3V
3.3V
JDIMM1
JDIMM2
P1-DIMMA1
Non-Maskable Interrupt
Front Panel Power On LED
Hard Drive Activity LED
Network Activity LED for LAN5*
Network Activity LED for LAN6*
Overheat / Fan Fail LED
- Red, Solid: System Overheat
- Red, Blinking (slow): Fan Fail
- Red, Blinking (fast): Power Fail
PWR Fail - Red, Solid: Power Fail
Reset Button*
Power Button
A
B
C
D
E
F
G
H
A
B
C
D
E
F
G
H
JDIMM1
JDIMM2
P1-DIMMA1
DIMMB1
DIMMB2
I
I
Front Panel Control (JF2)
1
NIC1 (Link) LED
2
NIC1 (Activity) LED
NIC2 (Activity) LED
NIC2 (Link) LED
78
NIC3 (Activity) LED
NIC4 (Activity) LED
NIC3 (Link) LED
NIC4 (Link) LED
Back Panel I/O
Note: Make sure that pins 2-3 of
jumpers JPF1 and JPF2 are set
appropriately according to the
conguration you have selected.
-
1
Supermicro X9SKV Quick Reference Manual
- Category
- Computer cases
- Type
- Quick Reference Manual
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Supermicro A1SRM-LN7F-2758 User manual
-
-
-
-
-
-
-
-
-
