BLACK+DECKER GKC1820L Owner's manual

Page is loading ...

5

ENGLISH

English

Intended use

Your Black & Decker Compact Chainsaw has been designed

for light duty cutting and pruning. This tool is intended for

consumer use only.

Safety instructions

General power tool safety warnings

Warning! Read all safety warnings and all

instructions. Failure to follow all instructions may

result in electric shock, fire and/or serious injury.

Save all warnings and instructions for future reference.

The term "power tool" in all of the warnings listed below

refers to your mains operated (corded) power tool or battery

operated (cordless) power tool.

1. Work area safety

a. Keep work area clean and well lit. Cluttered and dark

areas invite accidents.

b. Do not operate power tools in explosive

atmospheres, such as in the presence of flammable

liquids, gases or dust. Power tools create sparks

which may ignite the dust or fumes.

c. Keep children and bystanders away while operating

a power tool. Distractions can cause you to lose

control.

2. Electrical safety

a. Power tool plugs must match the outlet. Never

modify the plug in any way. Do not use any adapter

plugs with earthed (grounded) power tools.

Unmodified plugs and matching outlets will reduce risk

of electric shock.

b. Avoid body contact with earthed or grounded

surfaces such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric

shock if your body is earthed or grounded.

c. Do not expose power tools to rain or wet conditions.

Water entering a power tool will increase the risk of

electric shock.

d. Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool.

Keep cord away from heat, oil, sharp edges or

moving parts. Damaged or entangled cords increase

the risk of electric shock.

e. When operating a power tool outdoors, use an

extension cord suitable for outdoor use. Use of a

cord suitable for outdoor use reduces the risk of electric

shock.

f. If operating a power tool in a damp location is

unavoidable, use a Residual Current Device (RCD)

protected supply. Use of an RCD reduces the risk of

electric shock.

3. Personal safety

a. Stay alert, watch what you are doing and use

common sense when operating a power tool. Do not

use a power tool while you are tired or under the

influence of drugs, alcohol or medication. A moment

of inattention while operating power tools may result in

serious personal injury.

b. Use personal protective equipment. Always wear

eye protection. Protective equipment such as dust

mask, non-skid safety shoes, hard hat, or hearing

protection used for appropriate conditions will reduce

personal injuries.

c. Prevent unintentional starting. Ensure the switch is

in the off-position before connecting to power

source and/or battery pack, picking up or carrying

the tool. Carrying power tools with your finger on the

switch or energising power tools that have the switch on

invites accidents.

d. Remove any adjusting key or wrench before turning

the power tool on. A wrench or a key left attached to a

rotating part of the power tool may result in personal

injury.

e. Do not overreach. Keep proper footing and balance

at all times. This enables better control of the power

tool in unexpected situations.

f. Dress properly. Do not wear loose clothing or

jewellery. Keep your hair, clothing and gloves away

from moving parts. Loose clothes, jewellery or long

hair can be caught in moving parts.

g. If devices are provided for the connection of dust

extraction and collection facilities, ensure these are

connected and properly used. Use of these devices

can reduce dust related hazards

4. Power tool use and care

a. Do not force the power tool. Use the correct power

tool for your application. The correct power tool will do

the job better and safer at the rate for which it was

designed.

b. Do not use the power tool if the switch does not turn

it on and off. Any power tool that cannot be controlled

with the switch is dangerous and must be repaired.

c. Disconnect the plug from the power source and/or

the battery pack from the power tool before making

any a

djustments, changing access

ories, or storing

power tools. Such preventive safety measures reduce

the risk of starting the power tool accidentally.

!

6

ENGLISH

d. Store idle power tools out of the reach of children

and do not allow persons unfamiliar with the power

tool or these instructions to operate the power tool.

Power tools are dangerous in the hands of untrained

users.

e. Maintain power tools. Check for misalignment or

binding of moving parts, breakage of parts and any

other condition that may affect the power tools

operation. If damaged, have the power tool repaired

before use. Many accidents are caused by poorly

maintained power tools.

f. Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges are

less likely to bind and are easier to control.

g. Use the power tool, accessories and tool bits etc. in

accordance with these instructions, taking into

account the working conditions and the work to be

performed. Use of the power tool for operations

different from those intended could result in a

hazardous situation.

5. Battery tool use and care

a. Recharge only with the charger specified by the

manufacturer. A charger that is suitable for one type of

battery pack may create a risk of fire when used with

another battery pack.

b. Use power tools only with specifically designated

battery packs. Use of any other battery packs may

create a risk of injury and fire.

c. When battery pack is not in use, keep it away from

other metal objects, like paper clips, coins, keys,

nails, screws or other small metal objects, that can

make a connection from one terminal to another.

Shorting the battery terminals together may cause

burns or a fire.

d. Under abusive conditions, liquid may be ejected

from the battery; avoid contact. If contact

accidentally occurs, flush with water. If liquid

contacts eyes, additionally seek medical help. Liquid

ejected from the battery may cause irritation or burns.

6. Service

a. Have your power tool serviced by a qualified repair

person using only identical replacement parts. This will

make sure that the safety of the power tool is maintained.

Additional power tool safety warnings

 Hold power tool by insulated gripping surfaces

when performing an operation where the cutting

tool may contact hidden wiring or its own cord.

Contact with a "live" wire will also make exposed metal

parts of the power tool "live" and give the operator an

electric shock.

 Keep all parts of the body away from the saw chain

when the chainsaw is operating. Before you start

the chainsaw, make sure the saw chain is not

contacting anything. A moment of inattention while

operating the chainsaw may cause entanglement of

your clothing or body with the chainsaw.

 Always hold the chainsaw with your right hand on

the rear handle and your left hand on the front

handle. Holding the chainsaw with the reversed hand

configuration increases the risk of personal injury and

should never be done.

 Wear safety glasses and hearing protection. Further

protective equipment for head, hands, legs and feet

is recommended. Adequate protective clothing will

reduce personal injury by flying debris or accidental

contact with the saw chain.

 Do not operate a chainsaw in a tree. Operation of a

chainsaw while up in a tree may result in personal injury.

 Always keep proper footing and operate the

chainsaw only when standing on fixed, secure and

level surface. Slippery or unstable surfaces such as

ladders may cause a loss of balance or control of the

chainsaw.

 When cutting a limb that is under tension be alert for

spring back. When the tension in the wood fibres is

released the spring loaded limb may strike the operator

and/or throw the chainsaw out of control.

 Use extreme caution when cutting brush and

saplings. The slender material may catch the saw

chain and be whipped toward you or pull you off

balance.

 Carry the chainsaw by the front handle with the

chainsaw switched off and away from your body.

When transporting or storing the chainsaw always

fit the guide bar cover. Proper handling of the

chainsaw will reduce the likelihood of accidental contact

with the moving saw chain.

 Follow instructions for lubricating, chain tensioning

and changing accessories. Improperly tensioned or

lubricated chain may either break or increase the

chance for kickback.

 Keep handles dry, clean, and free from oil and

grease. Greasy, oily handles are slippery causing loss

of control.

 Cut wood only. Do not use chainsaw for purposes

not intended. For example: do not use the chainsaw

for cutting plastic, masonry or non-wood building

Warning! Additional safety warnings for chainsaws.

!

7

ENGLISH

materials. Use of the chainsaw for operations different

than intended could result in a hazardous situation.

 Position the cord so that it will not get caught on

branches or similar when cutting.

 The spiked bumper may become sharp during the

life of the product. Handle with care.

 When handling the product the chain bar may

become hot, handle with care.

Additional power tool safety warnings

The intended use is described in this instruction manual. Do

not use the tool for purposes not intended; for example do

not use the tool to fell trees. The use of any accessory or

attachment or performance of any operation with this tool

other than those recommended in this instruction manual

may present a risk of personal injury.

 Wear close fitting and protective clothing including a

safety helmet with visor/goggles, ear protectors, non-

skid safety footwear, protective bib trousers and strong

leather gloves.

 Always position yourself out of the path of falling

branches.

 The safe distance between a branch to be felled and

bystanders, buildings and other objects is at least 2 1/2

times the length of the branch. Any bystander, building

or object within this distance is at risk from being struck

by the falling branch.

 Pre-plan a safe exit from falling branches. Ensure the

exit route is clear of obstacles that would prevent or

hinder movement. Remember wet grass and freshly cut

bark is slippery.

 Ensure someone is nearby (but at a safe distance) in

case of an accident.

 Do not use the tool while standing in a tree, on a ladder

or on any other unstable surface.

 Keep proper footing and balance at all times.

 Hold the tool firmly with both hands when the motor is

running.

 Do not let the moving chain contact any object at the tip

of the guide bar.

 Start cutting only with the chain moving at full speed.

 Do not attempt to enter a previous cut. Always make a

fresh cut.

 Watch for shifting branches or other forces that could

close a cut and pinch or fall into the chain.

 Do not attempt to cut a branch when the diameter of the

branch exceeds the cutting length of the tool.

 Always remove the battery from the tool and place the

chain cover assembly over the chain when storing or

transporting the tool.

 Keep the saw chain sharp and properly tensioned.

Check the tension at regular intervals.

 Switch the tool off, allow the chain to stop and remove

the battery from the tool before carrying out any

adjustment, servicing or maintenance.

 Only use genuine replacement parts and accessories.

Causes and operator prevention of kickback

Kickback may occur when the nose or tip of the guide bar

touches an object, or when the wood closes in and pinches

the saw chain in the cut.

Tip contact in some cases may cause a sudden reverse

reaction, kicking the guide bar up and back towards the

operator.

Pinching the saw chain along the top of the guide bar may

push the guide bar rapidly back towards the operator.

Either of these reactions may cause you to lose control of the

chainsaw which could result in serious personal injury. Do

not rely exclusively upon the safety devices built into your

chainsaw. As a chainsaw user, you should take several

steps to keep your cutting jobs free from accident or injury.

Kickback is the result of tool misuse and / or incorrect

operating procedures or conditions and can be avoided by

taking proper precautions as given below:

 Maintain a firm grip, with thumbs and fingers encircling

the chainsaw handles. With both hands on the

chainsaw, position your body and arm to allow you to

resist kickback forces. Kickback forces can be

controlled by the operator, if proper precautions are

taken. Do not let go of the chainsaw.

 Do not overreach and do not cut above shoulder height.

This helps prevent unintended tip contact and enables

better control of the chainsaw in unexpected situations.

 Only use replacement guide bars and chains specified

by the manufacturer. Incorrect replacement guide bars

and chains may cause chain breakage and/or kickback.

 Follow the manufacturer's sharpening and maintenance

instructions for the saw chain. Decreasing the depth

gauge height can lead to increased kickback.

Safety recommendations for the chainsaw

 We strongly recommend that first time users obtain

practical instruction in the use of the chainsaw and

protective equipment from an experienced user. Initial

practice should be completed sawing logs on a saw

horse or cradle.

 We recommend that when carrying the chainsaw that

you make sure that the brake is engaged

Warning! Additional safety warnings for compact

chainsaws.

!

8

ENGLISH

 Maintain your chainsaw when not in use. Do not store

your chainsaw for any length of time without first

removing the saw chain and guide bar which should be

kept immersed in oil. Store all parts of your chainsaw in

a dry, secure place out of reach of children.

 We recommend you drain the oil reservoir prior to

storage.

 Be sure of your footing and pre-plan a safe exit from a

falling tree or branches.

 Use wedges to help control felling and prevent binding

the guide bar and saw chain in the cut.

 Saw chain care. Keep the saw chain sharp and snug on

the guide bar. Ensure the saw chain and guide bar are

clean and well oiled. Keep handles dry, clean and free

from oil and grease.

Kickback can be caused by:

 Striking branches or other objects accidentally with a tip

of the saw while the saw chain is moving.

 Striking metal, cement or any other hard material near

the wood, or buried in the wood.

 A dull or loose chain.

 Cutting above shoulder height.

 Lack of attention when holding or guiding the chainsaw

while cutting.

 Over-reaching. Keep proper footing and balance at all

times and do not overreach.

 Do not try to insert into a previous cut. As this could

cause kickback. Make a fresh cut every time.

 We strongly recommend you do not attempt to operate

your chainsaw while in a tree, on a ladder or on any

other unstable surface. If you decide to do so, be

advised that these positions are extremely dangerous.

 When cutting a branch that is under tension, be alert for

spring back so that you will not be struck when the

tension is released.

Avoid cutting:

 Prepared timber.

 Into the ground.

 Into wire fences, nails. etc.

 Into small sized brush and saplings because slender

material may catch the saw chain and be whipped

towards you, or pull you off balance.

 Do not use your chainsaw above shoulder height.

 Ensure someone is nearby (but at a safe distance) in

case of an accident.

 If for any reason you have to touch the saw chain, make

sure your chainsaw is disconnected from the mains.

 The noise from this product can exceed 80 dB(A). We

therefore recommend you take appropriate measures

for the protection of hearing.

Safety of others

 This appliance is not intended for use by persons

(including children) with reduced physical, sensory or

mental capabilities, or lack of experience and

knowledge, unless they have been given supervision or

instruction concerning the use of the appliance by a

person responsible for the their safety.

 Children should be supervised to ensure that they do

not play with the appliance.

Vibration

The declared vibration emission values stated in the

technical data and the declaration of conformity have been

measured in accordance with a standard test method

provided by EN 60745 and may be used for comparing one

tool with another. The declared vibration emission value may

also be used in a preliminary assessment of exposure.

Warning! The vibration emission value during actual use of

the power tool can differ from the declared value depending

on the ways in which the tool is used. The vibration level may

increase above the level stated.

 When assessing vibration exposure to determine safety

measures required by 2002/44/EC to protect persons

regularly using power tools in employment, an

estimation of vibration exposure should consider, the

actual conditions of use and the way the tool is used,

including taking account of all parts of the operating

cycle such as the times when the tool is switched off and

when it is running idle in addition to the trigger time.

Warning symbols

The following warning symbols are found on your tool:

Warning! To reduce the risk of injury, the user

must read the instruction manual.

Do not use your saw in wet conditions or

expose it to rain.

Always wear head and eye protection.

Always wear ear protection.

Always wear eye protection.

Always wear non-slip safety footwear.

9

ENGLISH

Additional safety instructions for batteries and chargers

Batteries

 Never attempt to open for any reason.

 Do not expose the battery to water.

 Do not expose the battery to heat.

 Do not store in locations where the temperature may

exceed 40°C.

 Charge only at ambient temperatures between 10°C

and 40°C.

 Charge only using the charger provided with the

appliance/tool. Using the wrong charger could result in

an electric shock or overheating of the battery.

 When disposing of batteries, follow the instructions

given in the section “Protecting the environment”.

 Do not damage/deform the battery pack either by

puncture or impact, as this may create a risk of injury

and fire.

 Do not charge damaged batteries.

Under extreme conditions, battery leakage may occur.

When you notice liquid on the batteries, carefully wipe

the liquid off using a cloth. Avoid skin contact.

In case of skin or eye contact, follow the instructions

below.

Warning! The battery fluid may cause personal injury or

damage to property. In case of skin contact,

immediately rinse with water. If redness, pain or

irritation occurs seek medical attention. In case of eye

contact, rinse immediately with clean water and seek

medical attention.

Chargers

Warning! Your charger has been designed for a specific

voltage. Always check that the mains voltage

corresponds to the voltage on the rating plate.

Warning! Never attempt to replace the charger unit with

a regular mains plug.

 Use your Black & Decker charger only to charge the

battery in the appliance/tool with which it was supplied.

Other batteries could burst, causing personal injury and

damage.

 Never attempt to charge non-rechargeable batteries.

 If the supply cord is damaged, it must be replaced by the

manufacturer or an authorised Black & Decker Service

Centre in order to avoid a hazard.

 Do not expose the charger to water.

 Do not open the charger.

 Do not probe the charger.

 The charger must be placed in a well ventilated area

when charging.

Labels on the charger

The following symbols are found on your charger:

Features

1. On/off switch

2. Lock-off button

3. Oil cap

4. Oil reservoir

5. Front guard assembly

6. Chain cover assembly

7. Chain tension adjustment screw

8. Chain

9. Guide bar

10. Battery

11. Chain sheath

12. Charger

Beware of falling objects.

Keep bystanders away.

To ensure continued safe operation, check the

chain tension as described in this manual after

every 10 minutes of use, and adjust back to a

clearance of 3 mm as required. Oil the chain

after every 10 minutes of use.

Warning! Do not touch chain at the chip

ejection point.

Direction of rotation of the chain.

To ensure continued safe operation, the chain

and guide bar must only be replaced with

original Black & Decker parts. Replacement

chain part number A6158 replacement guide

bar part number 90517720.

Your charger is double insulated; therefore no earth

wire is required. Always check that the power

supply corresponds to the voltage on the rating

plate. Never attempt to replace the charger unit with

a regular mains plug.

If the supply cord is damaged, it must be replaced

by the manufacturer or an authorised Black &

Decker Service Centre in order to avoid a hazard.

The charging base is intended for indoor use only.

Read the instruction manual before use.

10

Assembly

Warning! Before assembly, remove the battery (10) from the

tool.

Fitting and removing the battery (fig. A)



To fit the battery (10), line it up with the receptacle on

the tool. Slide the battery (10) into the receptacle and

push until the battery (10) snaps into place.

 To remove the battery (10), push the release button (24)

while at the same time pulling the battery (10) out of the

receptacle.

Warning! To prevent accidental operation, make sure that

the battery is removed and that the chain sheath (11) is in

place on the s

aw chain (8) before performing the following

operations. Failure to do this could result in serious personal

injury.

Installing and removing the saw chain (fig. C, E & G)

 Place the tool on a firm and stable surface.

 Loosen the two Allen screws (14) using the Allen key

(21) provided. Remove the Allen screws (14).

 Remove the chain cover assembly (6).

 Turn the chain tension adjustment screw (7) counter

clockwise to allow the guide bar (9) to recede and to

reduce the tension on the saw chain (8).



Remove the old saw chain (8) from the sprocket (15)

and the guide bar (9).

 Place the new saw chain (8) in the groove of the guide

bar (9) and around the sprocket (15). Make sure that the

teeth are facing the correct direction by matching the

arrow on the saw chain (8) with the arrow on the chain

cover assembly (6).



Make sure that the slot (17) in the guide bar (9) is over

the location pins (18) and that the hole (20) below the

slot is located over the adjustment pin (19).

 Fit the chain cover assembly (6) and the 2 Allen screws

(14).

 Tighten the Allen screws (14) using the Allen key (21)

provided.

Always wear protective gloves when installing or

removing the saw chain (8). The saw chain is

sharp and can cut you when it is not running.

easily done before. The battery may become warm while

charging; this is normal and does not indicate a problem.

Warning! Do not charge the battery at ambient temperatures

below 10 °C or above 40 °C. Recommended charging

temperature: approx. 24 °C.

Note: The charger will not charge a battery if the cell

temperature is below approximately 10 °C or above 40 °C.

The battery should be left in the charger and the charger

will begin to charge automatically when the cell

temperature warms up or cools down.

 To charge the battery (10), insert it into the charger (12).

force. Be sure that the battery is fully seated in the

charger.

 Plug in the charger and switch on at the mains.

The charging indicator (23) will blink.

The charge is complete when the charging indicator (23)

switches to continuously on. The charger and the battery can

charger occasionally tops up the battery charge.

 Charge discharged batteries within 1 week. Battery life will

be greatly diminished if stored in a discharged state.

Leaving the battery in the charger

The charger and battery pack can be left connected with the

pack fresh and fully charged.

 Adjust the chain tension as described below.

ENGLISH

11

Checking and adjusting the chain tension (fig. C and E)

 Check the saw chain tension. The tension is correct

when the saw chain (8) snaps back after being pulled

away 3 mm from the guide bar (9) with light force from

the middle finger and thumb. There should be no ‘sag’

between the guide bar (9) and the saw chain (8) on the

underside.

To adjust the tension:

 Loosen the 2 Allen screws (14).

 Turn the chain tension adjustment screw (7) clockwise.

Warning! Do not over-tension the chain as this will lead to

excessive wear and will reduce the life of the bar and chain.

 Once the chain tension is correct, tighten the 2 Allen

screws (14).

Warning! When the saw chain is new, check the tension

frequently during the first two hours of use as a new saw

chain stretches slightly.

Filling the oil reservoir (fig. G)



Remove the oil cap (3) and fill the reservoir (4) with the

recommended chain oil. You can see the oil level in the

oil reservoir (4). Refit the oil cap (3).

 Periodically switch off and check the oil level; if it is less

than a quarter full, remove the battery (10) from the tool

and ref

ill the reservoir (4) with the correct oil.

Oiling the chain (fig. G)

The saw chain (8) must be oiled before each use and after

cleaning using only the correct grade of oil (cat. no. A6027).

 Lubricate the saw chain (8) by pressing the bulb on the

oil cap (3) twice before making each cut, holding the

bulb down for 3-4 seconds.

Residual risks

Additional residual risks may arise when using the tool which

may not be included in the enclosed safety warnings. These

risks can arise from misuse, prolonged use etc.

Even wi

th the application of the relevant safety regulations

and the implementation of safety devices, certain residual

risks cannot be avoided. These include:



Injuries caused by touching any rotating/moving parts.



Injuries caused when changing any parts, blades or

accessories.

 Injuries caused by prolonged use of a tool. When using

any tool for prolonged periods make sure you take

regular breaks.

 Impairment of hearing.

 Health hazards caused by breathing dust developed

when using your tool (example:- working with wood,

especially oak, beech and MDF).

Use

Switching on and off (fig. G)

Warning! Let the tool work at its own pace, Do not overload.

For your safety, this tool is equipped with a double switching

system. This system prevents starting the tool inadvertently.

Switching on

 Press the lock-off button (2) and at the same time

squeeze the on/off switch (1).

 Release the lock-off button (2).

Switching off



Release the on/off switch (1).

Warning! Never attempt to lock a switch in the on position.

Pruning trees (fig. H)

Make sur

e that there are no local by-laws or regulations that

would prohibit or control the pruning of the tree limbs.

Pruning should only be undertaken by experienced users

there is an increased risk of the saw chain (8) pinching and

kickback.

Before pruning consideration should be given to conditions

affecting the direction of fall including:



The length and weight of the branch to be cut.



Any unusual heavy limb structure or decay.

 Surrounding trees and obstacles including overhead.

 The wind speed and direction.

 The branch being intertwined with other branches.

The operator should consider access to the tree limb and the

direction of fall. The tree branch is liable to swing towards the

tree trunk. In addition to the user bystanders, objects and

property below the branch will be at risk.

To avoid splintering, the first cut is made in an upward

direction to a maximum depth of one third the diameter of the

branch. The second cut is made downwards to meet the first.

Light duty cutting (fig. I)

How you should cut depends on how the log is supported.

Use a s

aw horse whenever possible. Always start a cut with

the saw chain (8) running and the spiked bumper in contact

with the wood. To complete the cut, use a pivoting action of

the spiked bumper against the wood.

When supported along its whole length:

 Make a downward cut, but avoid cutting the earth as this

will blunt your saw chain quickly.

When supported at both ends:

 First, cut one third down to avoid splintering and

second, cut again to meet the first cut,

When supported at one end:

ENGLISH

12

ENGLISH

 First cut one third up to avoid splintering and second, cut

down to prevent splintering.

When on a slope:

 Always stand on the uphill side.

When using a saw horse (fig. I):

This is strongly recommended whenever possible.

 Position the log in a stable position. Always cut on the

outside of the saw horse arms. Use clamps or straps to

secure the workpiece.

Cleaning, maintenance and storage

Your Black & Decker tool has been designed to operate over

a long period of time with a minimum of maintenance.

Continuous satisfactory operation depends upon proper tool

care and regular cleaning.

Your charger does not require any maintenance apart from

regular cleaning.

Warning! Before performing any maintenance on the tool,

remove the battery from the tool. Unplug the charger before

cleaning it.

After use and before storage

Regularly clean the ventilation slots with a clean, dry paint

brush.

To clean the tool, use only mild soap and a damp cloth.

Never let any liquid get inside the tool and never immerse

any part of the tool into liquid.

 Remove debris using a hard brush.

 Lubricate the chain (8) with oil.

Saw chain sharpening

If you are to get the best possible performance from the tool

it is important to keep the teeth of the saw chain sharp.

Guidance for this procedure is found on the sharpener

package. For this purpose we recommend the purchase of

the Black & Decker saw chain sharpening kit, available from

your Black & Decker service agents (cat. no. A6039).

Replacing worn out or damaged saw chains and guide

bars

Replacement saw chains are available through retailers and

Black & Decker service agents (pt no A6158), replacement

guide bars are only available through Black & Decker service

agents (pt no 90517720). To avoid the risk of injury, use only

original Black & Decker chains and guide bars. Always use

genuine spare parts.

Saw chain sharpness

The saw chain cutters will blunt immediately if they touch the

ground or a nail whilst cutting.

Saw chain tension

Regularly check the saw chain tension.

What to do if your chainsaw needs repair.

Your tool is in accordance with the relevant safety

requirements. Repairs should only be carried out by a

qualified person using original spare parts otherwise this

may result in considerable danger to the user. We

recommend you keep this user manual in a safe place.

Storage

When the tool will not be used for several months, ideally

leave the battery (10) connected to the charger.

Otherwise proceed as follows:

 Remove the battery (10) from the tool.

 Fully charge the battery (10).

 Store the tool and battery (10) in a secure and dry

location. The storage temperature must always remain

in the range of +10°C to +40°C. Place the battery (10)

on a level surface.

 Before using the tool after prolonged storage, fully

charge the battery (10) again.

Protecting the environment

Should you find one day that your Black & Decker product

needs replacement, or if it is of no further use to you, do not

dispose of it with household waste. Make this product

available for separate collection.

Separate collection of used products and packaging

allows materials to be recycled and used again. Re-

use of recycled materials helps prevent

environmental pollution and reduces the demand

for raw materials.

Local regulations may provide for separate collection of

electrical products from the household, at municipal waste

sites or by the retailer when you purchase a new product.

Black & Decker provides a facility for the collection and

recycling of Black & Decker products once they have

reached the end of their working life. To take advantage of

this service please return your product to any authorised

repair agent who will collect them on our behalf.

Separate collection. This product must not be

disposed of with normal household waste.

13

You can check the location of your nearest authorised repair

agent by contacting your local Black & Decker office at the

address indicated in this manual. Alternatively, a list of

authorised Black & Decker repair agents and full details of

our after-sales service and contacts are available on the

Internet at: www.2helpU.com.

Batteries



Do not short-circuit the battery terminals.



Do not dispose of the battery(s) in a fire as this may

result in a risk of personal injury or an explosion.



Run the battery down completely, then remove it from

the tool.



Batteries are recyclable. Place the battery(s) in a

suitable packaging to ensure that the terminals cannot

be short-circuited. Take them to any authorised repair

agent or a local recycling station.

Technical data

Guaranteed sound pressure level measured

according to EN60745:

L

pA

(sound pressure) 78.6 dB(A), uncertainty (K) 3 dB(A)

L

wA

(sound power) 89.6 dB(A), uncertainty (K) 3 dB(A)

Vibration total values (triax vector sum)

according to EN 60745:

Vibration emission value (a

h

)= 0.62 m/s²,

uncertainty (K) = 1.5 m/s²

EC declaration of conformity

MACHINERY DIRECTIVE

OUTDOOR NOISE DIRECTIVE

GKC1820L20

Black & Decker declares that these products described

under "technical data" are in compliance with:

2006/42/EC, EN

60745-1, EN60745-2-13

2006/42/EC, Chain Saw, Annex IV

KEMA Quality B.V., Utrechtseweg 310, 6802 ED Arnhem,

The Netherlands

Notified Body ID No.: 0344

Level of sound power according to 2000/14/EC

(Article 13, Annex III):

L

WA

(measure sound power) 89.6 dB(A)

L

WA

(guaranteed sound power) 90 dB(A)

These products also comply with directive 2004/108/EC

& 2011/65/EU. For more information, please contact

Black & Decker at the following address or refer to the

The undersigned is responsible for compilation of the

technical file and makes this declaration on behalf of Black

& Decker.

Kevin Hewitt

Vice-President Global Engineering

Black & Dec

ker Europe, 210 Bath Road, Slough,

Berkshire, SL1 3YD

United Kingdom

28-02-2014

At th

e e

nd of their useful life, discard batteries with

due care for our environment:

GKC1820L20 H1

Voltage Vdc 18

No load chain speed min

-1

190

Weight kg 2

Battery BL2018

81cdVegatloV

Capacity Ah 2.0

Type Li-Ion

Charger 905902** TYPE 1

Input voltage Vac 100-240

Output voltage Vdc 8-20

Output current mA 400

back of the manual.

ENGLISH

14

ENGLISH

Guarantee

Black & Decker is confident of the quality of its products and

offers an outstanding guarantee. This guarantee statement

is in addition to and in no way prejudices your statutory

rights. The guarantee is valid within the territories of the

Member States of the European Union and the European

Free Trade Area.

If a Black & Decker product becomes defective due to faulty

materials, workmanship or lack of conformity, within 24

months from the date of purchase, Black & Decker

guarantees to replace defective parts, repair products

subjected to fair wear and tear or replace such products to

ensure minimum inconvenience to the customer unless:

 The product has been used for trade, professional or

hire purposes.

 The product has been subjected to misuse or neglect.

 The product has sustained damage through foreign

objects, substances or accidents.

 Repairs have been attempted by persons other than

authorised repair agents or Black & Decker service

staff.

To claim on the guarantee, you will need to submit proof of

purchase to the seller or an authorised repair agent. You can

check the location of your nearest authorised repair agent by

contacting your local Black & Decker office at the address

indicated in this manual. Alternatively, a list of authorised

Black & Decker repair agents and full details of our after-

sales service and contacts are available on the Internet at:

www.2helpU.com

Please visit our website www.blackanddecker.co.uk to

register your new Black & Decker product and to be kept up

to date on new products and special offers. Further

information on the Black & Decker brand and our range of

products is available at www.blackanddecker.co.uk.

Page is loading ...

BLACK+DECKER GKC1820L, GKC1820L20 Owner's manual

Related papers