Coyote C2C36LP Owner's manual

FOR OUTDOOR USE ONLY

IMPORTANT: Read all instructions and warnings before using this product! Use of this

product, as with any similar outdoor grill, will involve risks from high temperatures and from

exposure to smoke and fumes. Please exercise caution and common sense.

To installer or person assembling grill: Leave this manual with grill for future reference.

To consumer: Keep this manual for future reference as it contains important Warnings and

Instructions.

COYOTE OUTDOOR LIVING, INC.

Coyote Stainless Steel Gas Grill

Use & Care Manual

For Liquid Propane and Natural Gas Models

Conforms to ANSI STD Z21.58-2015

Certified to CSA STD 1.6-2015

Outdoor Cooking Gas Appliance

4004477

PUT SERIES NO. LABEL HERE

C-Series 34" - C2C34

C-Series 36" - C2C36

C-Series 42" - C2C42

S-Series 36" - C2SL36

S-Series 42" - C2SL42

S-Series 30" - C2SL30

S-Series 30" - C2SL30-FS

1

Welcome & Congratulations

Congratulations on your purchase of a new grill! We are very proud of our product and we are

completely committed to providing you with the best service possible. Your satisfaction is our #1

priority.

Please read this manual carefully to understand all the instructions about how to install, operate

and maintain your grill for your safety and for optimum performance and longevity.

We know you’ll enjoy your new grill and thank you for choosing our product. We hope you consider

us for future purchases.

Read and save the instructions

Obey all Warnings and Instructions.

This Manual provides specific operating instructions for your model. Use your grill only as

instructed in this manual. These instructions are not meant to cover every possible condition and

situation that may occur. Common sense and caution must be practiced when installing,

operating and maintaining any appliance. If you lose this Manual, a replacement copy can be

downloaded from our website at www.coyoteoutdoor.com or call Customer Service at

855-520-1559.

2

Table of Contents & Critical Safety Warnings

Safety Instructions…. ......................... 3

Limited Warranty…………………………….5

Grill Models ....................................... 7

Locating the Grill............................... 8

Gas Requirements ………………………….12

Liquid Propane Gas Supply………..12

Natural Gas Supply.......................16

Connecting Electrical Transformer…..18

Operation of your Grill...................…..19

Lighting Your Grill ………………………….20

Using Your Burners & Grilling

Safely……………………………….................21

Care & Maintenance...........................24

Troubleshooting Your Grill..........……28

Parts Listings.................................…..30

Safety Symbols

DANGER

IF YOU SMELL GAS:

1. Shut off gas to the appliance.

2. Extinguish any open flame.

3. Open Lid.

4. If odor continues, keep away from the

appliance and immediately call your gas supplier

or your fire department.

WARNING

WARNING:

1. DO NOT store or use gasoline or other

flammable liquids or vapors in the vicinity of

this or any other appliance.

2. A Liquid Propane (LP) cylinder not connected

for use shall not be stored in the vicinity of this

or any other appliance.

DANGER

DANGER indicates an imminently

hazardous situation which, if not avoided,

will result in death or serious injury.

CAUTION

CAUTION indicates a potentially

hazardous situation which, if not avoided,

may result in minor or moderate personal

injury, or property damage.

WARNING

FOR OUTDOOR USE ONLY:

NEVER operate grill in enclosed areas, as this

could lead to gas accumulating from a leak,

causing an explosion or a carbon monoxide

buildup which could result in injury or death.

DO NOT use your grill in garages, breezeways,

sheds or any enclosed area. NOT FOR USE BY

CHILDREN. If these instructions are ignored, a

hazardous fire or explosion could result in

physical injury, death or property damage!

WARNING

WARNING indicates a potentially

hazardous situation which, if not avoided,

could result in death or serious injury.

3

Improper installation, adjustment, alteration, service, maintenance or

use can cause injury or property damage. Read the installation, operating and maintenance

instructions thoroughly before installation or servicing of this equipment.

General Safety Instructions

1. For Outdoor Use Only.

2. Coyote grills are only intended for residential use and are not intended for commercial use, where anyone

other than the original purchaser (homeowner) would be using and maintaining the grill.

3. NEVER use indoors or in any type of enclosed area, such as a garage, shed or breezeway. Keep clear of

trees and shrubs. The grills are not intended for installation in or on recreational vehicles, portable trailers,

boats or any other moving installation.

4. To reduce the risk of serious or fatal injury from breathing toxic fumes and from explosion and fire as a

result of leaking gas, use only outdoors in an open area with good ventilation. NEVER obstruct the flow of

combustion and ventilation air.

5. Fire Hazard: The area surrounding your new grill should be kept clean and free from flammable liquids

and other combustible materials such as mops, rags or brooms, as well as solvents, cleaning fluids, lighter

fluid and gasoline.

6. NEVER use the grill in windy conditions. If located in a consistently windy area (oceanfront, mountaintop,

etc.), a wind break will be required. Always adhere to the specified clearances listed in this Manual on

page 9.

7. NEVER leave the grill unattended while cooking.

8. Risk of Explosion: NEVER use natural gas in a unit designed for liquid propane gas or vice versa.

9. Do not use lighter fluid in a gas grill.

10. NEVER allow children to use or play near the grill. Keep children and pets away from a hot grill at all times

11. Installation and any repairs or replacement of parts should be performed by a qualified service technician.

If you are not qualified to install, repair, or replace parts of your grill, please retain a qualified professional

contractor or technician to do so.

12. Burn Hazard: NEVER lean over an open grill. Do not place clothing or other flammable material on or near

the grill. Do not wear loose-fitting clothes or long sleeves while using the grill as some fabrics can be highly

flammable and, if ignited, may result in personal injury or death.

13. Burn Hazard: When using the grill, do not touch the grill rack, burner grate, or immediate surroundings as

these areas become extremely hot and can cause burns. Always use a covered/gloved hand when opening

the grill hood and only do so slowly to allow heat and steam to escape.

14. ALWAYS: have an ABC fire extinguisher accessible.

15. NEVER attempt to extinguish a grease fire with water or other liquids as this may cause a flashback that

could result in personal injury or death.

16. NEVER use aluminum foil to line the grill racks or the drip trays, this can alter airflow for proper

combustion and also build up heat in the control area causing the knobs and cause damage to the igniter.

17. NEVER allow grease or other hot material to drip from the grill onto the valve, hose, or regulator. If that

Important Warnings and Safety

Instructions

4

occurs, turn off the fuel supply immediately. After the grill has cooled, determine the cause of the dripping

and correct it. After cleaning the valve, hose and regulator, perform a soapy water leak test before

continuing use. If a leak is discovered, call a qualified technician for service.

18. NEVER heat any unopened glass or metal container of food on the grill. Pressure may build up and cause

the container to burst, possibly resulting in death, serious personal injury, or property damage.

19. ALWAYS: Keep any electrical supply cords away from water or heated surfaces. Electrical cords should be

placed away from walkways to avoid tripping hazard.

20. ALWAYS: Keep gas supply lines as short as possible.

21. NEVER move the grill when hot.

22. NEVER use grill while under the influence of drugs or alcohol.

23. NEVER store a spare gas cylinder under or near your grill.

24. Fire Hazard: NEVER grill without the drip tray in place; hot grease could leak downward and produce a fire

or an explosion. Drip tray should be pushed all the way to the rack located just under the grill.

25. Fire Hazard: Grease is extremely flammable. Let hot grease cool down before attempting to handle or

dispose of it. After use and cool-down, the drip tray should be cleaned on a regular basis and kept free of

grease.

26. In the event that a burner goes out, turn burner knobs to the full OFF position, fully open the grill hood

and let it air out. NEVER attempt to use the grill until the gas has had time to dissipate.

27. Do not use a grill until a leak check has been completed.

28. ALWAYS: Turn off the LP cylinder tank valve when your grill is not in use.

29. ALWAYS: Ensure the control knobs are in the “OFF” position when not in use.

30. ALWAYS: Use only a Ground Fault Interrupter (GFI) protected circuit with this outdoor cooking gas

appliance.

DO NOT RELY JUST ON THIS SAFETY SECTION. USE CAUTION AND COMMON SENSE AT ALL TIMES.

PLEASE READ THE REST OF THIS MANUAL CAREFULLY FOR OTHER IMPORTANT SAFETY WARNINGS.

CALIFORNIA PROPOSITION 65 - WARNING: The burning of gas cooking fuels (propane gas) generates some

byproducts (including Benzene) which are on the list of substances which are known by the State of California

to cause cancer (birth defects) or reproductive harm. California law requires businesses to warn customers of

potential exposure to such substances. To minimize exposure to these substances, always operate this unit

according to the Use and Care Manual, ensuring you provide good ventilation when cooking with gas.

5

TO THE MAXIMUM EXTENT PERMITTED BY LAW, THIS LIMITED WARRANTY AND

THE REMEDIES SET FORTH BELOW ARE EXCLUSIVE AND IN LIEU OF ALL OTHER

WARRANTIES, REMEDIES AND CONDITIONS, WHETHER ORAL OR WRITTEN,

EXPRESS OR IMPLIED. TO THE MAXIMUM EXTENT PERMITTED BY LAW, COYOTE

OUTDOOR LIVING, INC. ALSO SPECIFICALLY DISCLAIMS ANY AND ALL IMPLIED

WARRANTIES, INCLUDING, WITHOUT LIMITATION, WARRANTIES OF

MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.

Coyote Outdoor Living, Inc. issues this limited warranty to the original purchaser at the original site of

delivery with proof of purchase and specifically warrants that the Outdoor Gas grill when subject to

normal residential use, will be free from defects in workmanship and materials for the periods specified

below. This limited warranty is not transferable and specifically excludes any grill used in a commercial

setting, where anyone other than the original purchaser (homeowner) would be using and maintaining

the grill. This limited warranty specifically excludes all issues that may arise from surface corrosion,

scratches, and discoloration during regular use. This limited warranty does NOT COVER LABOR OR LABOR

RELATED CHARGES and there will be shipping and handling charges for the delivery of part(s).

COMPONENT WARRANTY PERIOD

Cooking Grids (no rust or burn through) ………………………..................................5 years (limited)

Flavorizer Bars (no rust or burn through)………………………………….......................2 years (limited

Electric/Plastic Components ………………………………………………………....................2 years (limited)

Ignition systems/Valves ………………………………………………………………...................1 year (limited)

Stainless steel frame/housing …………………………………………………….....................Limited Lifetime

Stainless Steel Burners (no rust or burn through)..………………….........................Limited Lifetime

Coyote Outdoor Living, Inc.’s obligation under this limited warranty is limited solely to repair or

replacement, at our option, of the pertinent component during the warranty period, and the extent of any

liability of Coyote Outdoor Living, Inc. under this warranty is limited to repair or replacement. This limited

warranty does not cover normal wear of parts or damage resulting from any of the following: negligent

use or misuse of the product, use of an improper fuel/gas supply, use contrary to operating instructions,

or alteration by any person other than a factory service center. The above warranty periods are not

extended by any repair or replacement.

WARRANTY CLAIM PROCEDURE: If you require service or parts for your Coyote Grill, please contact our

Warranty Service Center for factory direct assistance. Our hours of operation are 8 am to 4:30 pm CST.

The phone number is 855.520.1559 and the email address is [email protected]m. You may also

fill out warranty claims online at www.coyoteoutdoor.com. Please have your model number, serial

number and proof of purchase available for any warranty claim.

Coyote Outdoor Living, Inc. may require the return of defective parts for examination before issuing

replacement parts. If you are required to return defective parts, shipping charges must be prepaid by the

customer. Upon examination and to Coyote Outdoor’s determination, if the original part is proven

Limited Warranty

6

defective, Coyote Outdoor may approve your claim and elect to replace such parts without charge. In

every instance, the customer is responsible for shipping and handling of replacement parts. Component

repair or replacement is the exclusive remedy under this limited warranty and Coyote Outdoor shall not

be liable for any incidental or consequential damages.

This limited warranty does not cover any failures or operating difficulties due to accidents, abuse, misuse,

alteration, misapplication, vandalism, improper installation, maintenance or service, or damages caused

by flashback fire or grease fire. This limited warranty does not cover scratches, dents, corrosion or

discoloration caused by weather, heat, abrasive and chemical cleaners, pool or spa chemicals, and/or any

tools used in the assembly or installation of this unit. This limited warranty does not cover paint loss,

surface rust, corrosion or stainless steel discoloration which is considered normal wear and tear. This

limited warranty does not cover the cost of any inconvenience, personal injury, or property damage due

to improper use or product failure. Deterioration or damage due to severe weather conditions such as hail,

hurricanes, earthquakes, tsunamis, tornadoes, terrorism, discoloration due to exposure to chemicals

either directly or in the atmosphere, Acts of God/forces of Nature are not covered by this limited

warranty.

7

Whether you are in need of a slimmer 3 Burner grill for your patio, or are in need of a larger 42” grill that can

entertain and bring style to any size party, Coyote has the grill for you!

Model No.

Product

Size

(inch/mm)

BTU/HR

(Main/Back)

Burner(s)

Rotisserie

Motor

Hood Light

C2C34 34" (863) 60,000/None 3 Infinity Burners No Yes

C2C36 36" (902) 80,000/None 4 Infinity Burners No Yes

C2C42 42" (1067) 100,000/None 5 Infinity Burners No Yes

C2SL30 / C2SL30-FS 30" (762) 55,000/15,000

2 infinity burners, 1 sear

and 1 back burner

Yes Yes

C2SL36 36" (902) 75,000/15,000

3 infinity burners, 1 sear

and 1 back burner

Yes Yes

C2SL42 42" (1067) 95,000/15,000

4 infinity burners, 1 sear

and 1 back burner

Yes Yes

Grill Models

C-Series 34" - C2C34

C-Series 36" - C2C36

C-Series 42" - C2C42

S-Series 36" - C2SL36

S-Series 42" - C2SL42

S-Series 30" - C2SL30

S-Series 30" - C2SL30-FS

8

Check your local building codes for the proper method of installation. In the absence of local codes, this unit

should be installed in accordance with the National Fuel Gas Code No. Z223.1-1998 USA or CAN/CGA-B149.1/.2

Natural Gas/Propane Code (Canada) latest edition or the National Electrical Code ANSI/NFPA No. 70 or the

Canadian Electrical Code CSA C22.1, 1990 or latest version.

• Before installing built-in grills in enclosures, copy all product information such as model number, serial

number and type of grill (e.g. natural gas or LP) and store information in a safe place.

• If the grill is installed by a professional installer or technician, be sure that he or she shows you where your

gas supply shut-off is located. All gas lines must have a shut-off that is readily and easily accessible. If you

smell gas, check for gas leaks immediately. Check only with a soap and water solution. Never check for gas

leaks with an open flame.

Notice:

We strongly recommend professional installation of your Coyote grill. These instructions provide the

measurements necessary to construct a masonry structure to house your outdoor gas grill.

IMPORTANT:

Gas fittings, regulator, and installer supplied shut-off valves must be easily accessible.

LOCATION OF YOUR GRILL:

Locate the grill only OUTSIDE in a well-ventilated area. Never locate the grill in a building, garage, breezeway,

shed or other such enclosed areas without an approved ventilation system. When in use, the grill will

generate a lot of smoke. When installing your grill, select an outdoor location that will ensure there is adequate

area for the smoke to dissipate IN ORDER TO AVOID INHALATION OF POTENTIALLY TOXIC FUMES.

Ventilation Requirements for Proper Operation of your Coyote Grill

• Ventilation for a gas grill is absolutely mandatory to ensure that your grill performs as intended and to

ensure the safety of you, your family, and guests. Proper ventilation is necessary to allow heat inside

your grill to escape and also to allow any gas that has leaked from a tank or connection to escape

before a buildup of such gas can occur and possibly ignite. Failure to

provide proper ventilation will nullify Coyote’s warranty and will cause a risk of bodily injury or death.

• If you elect to install your grill into an island, the island itself must be ventilated properly. Any such

island must have a minimum of 2 vents (but optimally 4 vents) per cabinet that has any sort of gas

supply or connection. Each vent must be at least 20 sq. in in size and have access to outside/fresh air.

Those vents will allow heat that is trapped inside due to wind to be able to dissipate out of the island

vents. However, if the island is not ventilated properly and the wind is coming from the back, then the

heat will try to escape through the easiest exit, which will most likely be through the bottom of the grill

and front control panel.

• A simple way to think of what is occurring inside your grill is that when your burners are on, they are

emitting a flame that creates the heat to cook your food. This heat must exhaust or escape from the

grill, otherwise you would eventually have a unit that would not only build up intense heat but also

dangerous pressure. This could cause severe damage to not only the grill but any operators or people

or property near-by. The grill itself allows for ventilation mainly through the rear of the unit above the

rear panel but below the top of the hood. However, wind can act as a barrier to ventilation and

exhaust. This blockage of exhaust can cause problems and hazardous conditions. Therefore, great care

must be taken in selecting a location for your grill and in the installation of it into any masonry island

Locating the Grill

9

or other outdoor structure. This can cause the control panel and knobs to get hot to the touch and

possibly even burn your fingers, not to mention that it can melt all rubber gaskets on the valves and

damage the ignition system to where it will need full replacement.

• Ventilation and typical wind direction and conditions must always be considered when planning your

outdoor cooking island. Just the same as you would plan the layout and measure your indoor kitchen,

you must also do the same for the outdoors; but you cannot forget about Mother Nature and the

effects she can have on your outdoor cooking equipment.

o Coyote Wind Guards: If you do run into a situation where you will have wind coming into the

back of the unit, Coyote offers "Wind Guards" that reduce risks of overheating in the event of

ventilation interference. Our Wind Guards should never be considered as a guaranteed

solution to this problem. They are only intended to help the wind divert up and over the top of

the grill. If the wind is strong, then you can still have problems with the heat being trapped in

the hood. Coyote Wind Guards can be purchased through any of our authorized dealers.

Clearance

:

• FROM NON-COMBUSTIBLE MATERIALS: Coyote grills can be placed directly on, or adjacent to,

non-combustible materials, subject to ventilation requirements. The hood on a Coyote grill pivots

mainly on the body. If you have a wall or partition behind the unit that would block ventilation, then a

minimum of 7" clearance from the back of the grill to the wall is needed for the purpose of ventilation.

If you do not have a wall or partition blocking the ventilation of the unit, then you only need an extra

2" behind the unit for the hood to open fully. If you wish to use the rotisserie option, you will want to

make sure that you leave adequate space (at least 6") on each side of the grill so that the motor and

rotisserie spit handle will have room on the counter, as these extend past the overall dimensions of

the grill body.

• FROM COMBUSTIBLE MATERIALS: Coyote grills must have at least 24" clearance from any combustible

materials (in any direction) for the safety of the homeowner and for any Coyote Warranty to remain in

effect.

o You CANNOT locate the grill under any combustible material without an approved ventilation

system located directly above the unit. To elaborate, Coyote defines an approved ventilation

hood as:

 The ventilation hood chosen must be UL certified, produced for outdoor use and must be

installed according to the hood manufacturer’s specifications.

 The hood must be installed at least 30" above the top of the cooking surface.

 The hood must be at least 6" wider that the grills frame (3" on each side), not just the cooking

surface.

•

INSULATED JACKETS AND COMBUSTIBLE CONSTRUCTION:

If you elect to use combustible material to

build your grill island AND the grill will be located within 24" of the combustible material, then you

must use the appropriate Coyote insulated jacket. The insulated jacket will act as a barrier to protect

your grill island from the heat and fire of your Coyote grill. If an insulated jacket is not used in a

combustible material island, the warranty on the Coyote grill will be voided immediately and safety

cannot be ensured.

For Built-in Installations

A built-in grill is designed for easy installation into masonry enclosures. For non-combustible applications, the

grill drops into the opening (as shown in cut-out detail drawing - Fig. A) and hangs from the grill body itself. A

bottom deck is not required to support the grill from the bottom. It is also required that:

10

• A minimum of two ventilation holes in the enclosure, of at least 20 sq. inches in size (per vent), must

be present to help release any leaking gas from the enclosure.

 As Propane is heavier than air, for propane grills locate your vents at the tank valve height or

lower

 As Natural Gas is lighter than air, for natural gas grills locate your vents at the gas connection

height or higher

• The counter should be flat and level relative to the floor.

LP TANK STORAGE MUST BE ISOLATED IN A SEPARATE COMPARTMENT FROM THAT

OF THE GRILL AND IT MUST BE VENTED AS WELL. (RECOMMEND BOTTOM VENTS FOR LP)

High Elevation Installation and Use

Coyote Grills are designed to operate most efficiently at 0-2000 feet above sea level. From 2000-4000 feet above sea

level you will not notice any substantial decrease in your heat, although more gas is combusting within the burners

due to less oxygen. Above 4000 feet, you may experience longer cooking times on your grill than experienced at sea

level. This is due to the air/fuel mixture taking place within the burners. If you have questions or concerns

regarding your location or elevation, please contact Coyote Customer Service for assistance.

11

Cut out Dimensions Figure A

Model Cutout Dimensions Overall Dimensions Total BTU Ratings

Electrical Outlets

Needed (110V)

Grills

Height Width Depth Height Width Depth LP NG Rotisserie Lights

C2C34 10 1/4" 31" 20 1/2" 23” 34" 25 1/2” 60,000 60,000 No Qty 1

C2C36 10 1/4" 32 1/2" 20 1/2" 23” 35 1/2" 25 1/2” 80,000 80,000 No Qty 1

C2C42 10 1/4" 39 1/2" 20 1/2" 23” 42" 25 1/2” 110,000 110,000 No Qty 1

C2SL30 10 1/4" 27” 20 1/2" 23” 30” 25 1/2” 70,000 70,000 Qty 1 Qty 1

C2SL36 10 1/4" 32 1/2" 20 1/2" 23” 35 1/2" 25 1/2” 90,000 90,000 Qty 1 Qty 1

C2SL42 10 1/4" 39 1/2" 20 1/2" 23” 42" 25 1/2” 110,000 110,000 Qty 1 Qty 1

Height

Minimum of 2 vents, but optimally 4 vents, per cabinet that has any sort of gas supply or

connection. Each vent must be at least 20 sq in in size and have access to outside/fresh air.

Two vents on each side will facilitate and improve airflow and ventilation.

Vent

Width

Depth

12

Never attach an unregulated gas line to the appliance.

Connection to an unregulated gas line can cause

excessive heat or fire and the risk of property damage,

bodily injury, or death.

IMPORTANT:

Before connecting grill to gas source, make sure grill control knobs are in the “OFF” position.

• Verify the type of gas supply to be used, either natural or liquid propane, and make sure the marking

on the appliance rating label agrees with that of the gas supply. Do not connect a Coyote liquid

propane gas grill to a natural gas supply, and do not connect a Coyote natural gas grill to a liquid

propane gas supply.

• All pipe sealants must be an approved type and resistant to the actions of LP gas. Never use pipe

sealant on flare fittings.

• The installation of this appliance must conform with local codes or, in the absence of local codes, with

either National Fuel Gas Code, ANSI Z223.1/ NFPA 54, Natural Gas and Propane Installation Code, CSA

B149.1, or Propane Storage and Handling Code, B149.2, or the Standard for Recreational Vehicles, ANSI

A 119.2/ NFPA 1192M, and CSA Z240 RV Series, Recreational Vehicle Code, as applicable.

Gas valves are preset at the factory to operate on liquid propane

or natural gas. If you wish to convert, be sure to contact your grill

dealer FIRST!

Always check the rating plate to make sure gas supply to which you connect the grill is the gas type for which

the grill is manufactured. A Coyote liquid propane (LP) gas grill is designed to operate on propane gas ONLY,

at a pressure regulated at 11” (279.4mm) water column (W.C.) when equipped with the correct propane

orifices on the valves and a propane regulator on the supply line regulated at the residential meter. A Coyote

liquid propane gas grill comes with a propane regulator that is designed to be used with a standard 20 lb. gas

cylinder and those cylinders must be constructed and marked in accordance with specifications of the US

Department of Transportation for propane gas cylinders.

• Liquid propane (LP) gas is flammable and hazardous if handled improperly. Know its characteristics

before using any propane products.

• Propane characteristics include: flammable, explosive under pressure, heavier than air and settles

NOTE: Coyote strongly recommends that a qualified service technician perform

the initial installation and all conversions or modifications to the gas supply.

Liquid Propane Gas Supply

Gas Requirements

13

in pools and low areas.

• In its natural state, propane has no odor. For your safety, an odorant typically is added. ALWAYS

purchase or refill your propane tanks from a reputable propane gas supplier.

• Contact with propane can cause freeze burns to the skin.

• NEVER use a propane cylinder with a damaged body, valve, collar or footing.

• A dented or rusted propane cylinder may be hazardous.

• Always keep LP cylinder securely fastened in an upright position.

• Never connect an unregulated propane gas cylinder to the grill.

• NEVER subject (expose) propane cylinders to excessive heat.

•

Never store a LP gas cylinder inside a building or in the vicinity of any gas-burning appliance.

Cylinder Specifications

• Any L.P. gas supply cylinder used with this grill must be approximately 12 inches diameter and 18 inches

high. The maximum fuel capacity is 80% and is approximately 20 pounds of propane.

• The L.P. cylinder must have a shut-off valve (see picture) terminating in a Type 1 L.P.

• A Type 1 compatible cylinder with a Type 1 cylinder valve has a back-check valve which does not permit

gas flow, until a positive seal has been obtained.

• The cylinder must be arranged for vapor withdrawal. It must also include a

collar to protect the cylinder valve. A safety relief device having direct

communication with the vapor space of cylinder must be provided. This will

expel high pressure gas if the cylinder is overfilled or overheated which

could result in fire or explosion.

• All L.P. gas cylinders used with this appliance shall be constructed and

marked in accordance with the specifications for L.P. gas cylinders of the U.

S. Department of Transportation (DOT) or the National Standard of Canada,

CAN/CSA-B339, Cylinders, Spheres and Tubes for Transportation of

Dangerous Goods; and Commission, as applicable; and shall be provided

with a listed overfilling prevention device.

• Read labels on the L.P. Gas Supply Cylinder.

• New cylinders are always shipped empty for safety.

• Allow only qualified L.P. gas dealers to fill or repair your L.P. gas supply cylinder.

• Inform the gas dealer if it is a new or used cylinder to be filled.

• After filling, have the gas dealer check for leaks and to see that the relief valve remains effective and in

good repair.

Hose and Regulator (Comes standard with the grill)

The Type 1 connection system has the following features:

• The system will not allow gas to flow until a positive connection has

been made.

The cylinder control valve must be

turned off before any connection is made or removed.

• The system has a thermal element that will shut off the flow of gas in

the event of a fire.

14

• The system has a flow limiting device which, when activated, will limit the flow of gas to 10 cubic feet per

hour.

• NEVER use grill without leak testing this connection.

LP (Propane) Gas Supply Connection

1. The tank valve should be in the “OFF” position. If not, turn the knob

clockwise until it stops.

2. Make sure all burner valves are in the “OFF” position.

3. Always connect the gas supply regulator as follows:

Insert the regulator inlet into the tank valve and turn the coupling nut

clockwise until the coupler tightens up (see picture). Do not over-tighten the

coupler. Turn the main tank valve on, and turn the burner control valves on

the unit to the “HIGH” position for about 20 seconds to allow the air in the

system to purge before attempting to light the burners.

Pre-Operation Leak Testing

1. Do not insert any tool into the valve outlet or safety relief valve. You may damage the valve and cause a

leak. Leaking propane may result in explosion, fire, severe personal injury, or death.

2. If a leak is detected at any time, or you cannot stop a gas leak, immediately close the tank’s shut-off valve

(gas supply from LP tank to the Grill) and call LP gas supplier or your fire department!

3. Check all gas supply fittings before each use and each time the gas supply cylinder is connected to the

regulator. Have a qualified service technician leak test the grill any time a part of the gas system is

replaced.

Never attempt to attach this grill to the self-contained LP gas system. Do not use the grill until leak testing has

been completed.

Leak Testing Valves, Hose and Regulator

1. NEVER smoke while leak testing.

2. Extinguish all open flames. Never leak test with an

open flame.

3. Mix a solution of equal parts mild detergent or liquid

soap and water.

4. Turn all grill control knobs to OFF.

5. Ensure that the connections from the regulator to the

grill and tank are tight and secure (see picture).

6. Completely open LP tank valve by turning cylinder

valve knob counterclockwise (right to left). If you hear

a rushing sound, turn gas off immediately. There is a

major leak at the connection. Correct before

15

proceeding by calling the Coyote Customer Service line at 855-520-1559.

7. If no rushing sound, brush soapy solution onto areas where bubbles are shown in LP tank (see picture).

8. If “growing” bubbles appear, there is a leak. Close LP tank valve immediately and retighten connections. If

leaks cannot be stopped, do not try to repair the regulator, or tank valve, by yourself and contact the

Coyote Customer Service line at 855-520-1559.

9. Always close LP tank valve after performing leak test by turning cylinder valve knob clockwise.

NOTE:

When leak testing this appliance, make sure to test and tighten all loose connections. A slight leak in

the system can result in a low flame, or a hazardous condition that could result in a fire or explosion.

LP Gas Supply Cylinder Disconnection

In order to disconnect the LP tank from the grill:

1. Turn the burner valves off.

2. Turn the tank valve off. (Turn shut-off clockwise to stop).

3. Detach the regulator assembly from the tank valve by turning the quick coupling nut counterclockwise.

LP Tank Removal, Transport and Storage

• Turn OFF all control knobs and LP tank valve. Turn coupling nut counterclockwise by hand only - do not

use tools to disconnect. Install safety cap onto LP tank valve. Always use cap and strap supplied with valve.

Failure to use safety cap as directed may result in serious personal injury

and/or property damage.

A disconnected LP tank in storage or being transported must have

a safety cap installed (as shown).

• Never leave a LP tank inside a motor vehicle. (Heating of the

vehicle could cause an increase in the gas pressure which may

open the release vale allowing gas to escape resulting a serious

risk of fire or explosion.)

• Do not store an LP tank in enclosed spaces such as a carport,

garage, porch, covered patio or other building.

• Do not store LP tank in an area where children play.

LP Tank Filling

• Use only licensed and experienced LP dealers.

• LP dealer must purge tank before filling.

• Dealer should NEVER fill LP tank more than 80% of LP tank volume. Volume of propane in tank will vary by

temperature.

• A frosty regulator indicates gas overfill. If frosty, immediately close LP tank valve and call local LP gas

dealer for assistance.

• Do not release liquid propane (LP) gas into the atmosphere. This is a hazardous practice.

• To remove gas from LP tank, contact an LP dealer or call a local fire department for assistance.

LP Tank Exchange

• Exchange your Type 1 cylinder for OPD safety feature-equipped replacement tank ONLY.

• Always keep new and exchanged LP tanks in upright position during use, transit or storage. Leak test new

and exchanged LP tanks BEFORE connecting to grill.

16

Large Capacity Propane Tanks and Homes:

• If your entire house is plumbed for propane gas use, and you have an exterior connection for such use,

then a standard LP grill from Coyote can be connected to such outdoor propane connection, but you

must be aware of the following:

o Coyote does not supply any gas fittings or lines, other than the regulator needed within the

grill box

o All Coyote LP Grills come with a 20lb tank regulator. This regulator cannot be used or modified

to work on any other setup.



If you are running off of a large capacity tank (more than

20lbs), then an “in-line” LP regulator is needed, which can be purchased from any

Coyote authorized dealer, or plumbing supply company. However, it is the

responsibility of the owner/installer to verify that the correct regulator is purchased

for the intended application and that it is installed properly.

o As codes vary from state to state, it is the responsibility of the owner/installer to ensure that

all county, state and federal codes are followed for any gas installation.

•

Always check the rating plate to make sure the gas supply to which you connect the grill is the gas type the grill

is manufactured for.

A Coyote natural gas (NG) grill is designed to operate on natural gas ONLY, at a

pressure regulated at 4” (101.6mm) water column (W.C.) when equipped with the correct natural gas orifices

on the valves and a natural gas regulator on the supply line regulated at the residential meter.

Never connect the grill to an unregulated gas supply.

NATURAL GAS CONNECTIONS MUST BE PERFORMED BY A LICENSED CONTRACTOR OR LOCAL GAS COMPANY

REPRESENTATIVE.

Natural Gas Regulator

NEVER use grill without leak testing this connection.

Natural gas regulator model: GR120

Gas pressure: 4” (101.6mm)

Maximum rate working pressure: 1/2 Psig

Leak Testing Valves, Hose and Regulator

1. NEVER smoke while leak testing.

2. Extinguish all open flames. Never leak test with an open flame.

Natural Gas Supply

17

3. Mix a solution of equal parts mild detergent or liquid soap and water.

4. Turn all grill control knobs to OFF.

5. Ensure that the connections from the regulator to the grill and tank are tight and secure.

6. Completely open the shut-off valve. If you hear a rushing sound, turn gas off immediately. There is a major

leak at the connection. Correct before proceeding by calling the Coyote Customer Service line at

855-520-1559.

7. If no rushing sound, brush soapy solution onto all connection points.

8. If “growing” bubbles appear, there is a leak. Close the shut-off valve immediately and retighten

connections. If leaks cannot be stopped, do not try to repair the regulator, or shut-off valve, by yourself

and contact the Coyote Customer Service line at 855-520-1559.

NOTE:

When leak testing this appliance, make sure to test and tighten all loose connections. A slight leak in

the system can result in a low flame, or a hazardous condition that could result in a fire or explosion.

Natural Gas Supply and Connection

1. Make sure all burner valves are in the “OFF” position

2. All NG units need to have a regulator and shut-off valve on the supply line.

3. All Pipe threads need to have proper, gas-rated, outdoor-rated thread sealant. Flare ends do not need or

utilize pipe sealant.

4. Your NG Coyote grill comes with a ½” regulator

a) Installer needs to seal the regulator to the hose using pipe sealant.

b) Then attach the flare end to manifold line, with no pipe sealant.

c) Next, attach connection hose (not included) to the other side of the NG regulator (it is also ½” MIP)

i. We suggest using ½” stainless steel corrugated hoses for all NG Grills

ii. Make sure that you purchase a hose of adequate length and capacity for the intended

application.

d) Connect the other end of this hose to shut-off valve

i. Depending on your choice of hose and shut-off, the nipple going into the shut-off valve may

vary.

e) Test all connections for leaks with a soap and water solution.

Coyote is not responsible for the selection or performance of the contractor or installer who performs the

connection of the natural gas supply to the grill.

Gas Conversions – Natural Gas and Propane

Coyote grills are able to be converted (a Coyote liquid propane grill can be converted to a natural gas grill or vice

versa), but you must obtain the correct conversion kit and we recommend that any gas appliance conversion should

be performed by a Licensed Plumber or a certified Installer. Conversion kits are sold for Coyote grills and can be

purchased through your dealer or Coyote’s Customer Service Department. Any other kit or orifices used that are not

of Coyote brand will automatically void any Coyote Warranty on the unit. Furthermore, it is important to understand

that wherever there is a burner, there is an orifice that will need to be changed (do not forget the rotisserie or sear

burner).

The steps for converting your Coyote grills main and sear burners are:

1. Pull grill out of island or cart.

2. Remove Drip Pan and Cooking Grates.

3. Unscrew bolt connecting the manifold pipe to the grill body, located at the back side of the grill.

18

4. Unscrew the 4 bolts holding the faceplate to the body (on the front edge where your cooking grate sits).

5. Unscrew the 2 bolts (on each side) of the manifold and faceplate assembly that holds this entire assembly

to the body of the grill.

6. Disconnect all wires and flex lines, from the valves and igniter assembly while paying close attention to their

original location.

7. Slide entire control panel and valve assembly out from the grill body.

8. Flip control panel over on its side, so you have easy access to the valves.

9. Sear Burner Grills Only – Remove center knob, unscrew top and bottom screws only.

a. The safety valve that controls the thermocouple on your sear burner must be completely changed.

You cannot change only the orifice.

10. Sear Burner Grills Only – Unscrew base bracket, hold center valve to gas manifold pipe and remove valve.

11. Sear Burner Grills Only – Install new Safety Valve in the correct gas type and follow the removal instructions

in reverse.

12. Once the panel is flipped over, you will see the orifice at the end of the valve. With a wrench remove the

orifice from the valve and install the new gas orifice,

13. Re-assemble in reverse and test all connections again with a soapy water solution to ensure no leaks.

To convert your rear burner orifice:

1. Remove your entire rotisserie assembly.

2. Remove the back panel that covers your rear rotisserie burner.

a. With the hood open, remove the 4 screws on top of this panel.

b. With the hood closed, remove the 4 screws on the back of this panel.

c. With the hood closed, look underneath this same back panel and you will see 4-5 bolts (depending

on your grill), these only need to be loosened.

3. Next, pull the entire panel (starting from the back) out from the grill

a. It is designed to fit tight, so you may need a flat head screwdriver to pop the stainless away from the

body.

4. Next, you will see the gas line, brass elbow and orifice.

5. Use a wrench to remove the orifice and install the new one.

6. Re-assemble in reverse and check your back burner to ensure proper ignition and burning.

Instruction for Connecting the Transformer

1. Transformer for Interior & LED Lights - Your grill’s electrical transformer will connect on the left side of

your grill (looking at it from the front) and operates the hood lights inside your grill, along with the LED

lights on the SL models. Follow the pictures and insert the white male plug into the white female socket, on

the left side of your grill and then plug the transformer into a standard 110v outlet. If you have any

questions or concerns, please consult or use a qualified electrician.

Left Side of Grills Male Plug Female Socket

19

GENERAL RULES

NEVER leave the grill unattended while cooking!

• Make sure the grill has been leak-tested and is properly located, with necessary ventilation and

clearances.

• Check that the end of each burner tube is properly located over each valve orifice.

• Light the grill burners using the instructions provided in this manual.

• Adjust heat settings to your desired cooking temperature.

• Allow grill to cool down, wipe off any splatters or grease and clean the drip tray.

• NEVER put a cover on the grill while it is still hot as it could start a fire.

• NEVER use the grill if gas odor is present.

• NEVER stand with head, body, or arms over the grill when lighting.

• ALWAYS inspect the hose before using the grill. If there is excessive abrasion or wear, or if the hose is

cut, it must be replaced prior to the outdoor cooking gas appliance being put into operation. The

replacement hose assembly shall be that specified by the manufacturer.

• ALWAYS ensure the area around the barbecue is clear of flammable substances such as gasoline, yard

debris, wood, etc.

• ALWAYS ensure there is no blockage of the airflow through the vent space located below the face of

the unit.

• Failure to open the lid prior to igniting the barbecue’s burners, or not waiting 5 minutes to allow the

gas to clear if the barbecue does not light, may result in an explosive flame-up which can cause

serious bodily injury or death.

Operating the Grill

Keep any electrical supply cords and the fuel

supply hose away from any heated surfaces.

Page is loading ...

Coyote C2C36LP Owner's manual

Related papers

Other documents