CURT 112103 is a trailer hitch designed for the Ford Mustang. It has a gross load capacity of 2,000 lbs. trailer weight and 200 lbs. tongue weight. The hitch is easy to install and can be done in 30 minutes by a professional or 60 minutes by a novice.
Here are some of the features of the CURT 112103:
- No drilling required
- Fishwire hardware
- Lower exhaust
- Designed for use with ballmount #D-20/45520
- Euro mount option available #45561 (1 7/8" ball) & #45562 (2" ball)
- Hitch weight: 26 lbs.
The CURT 112103 is a great way to add towing capacity to your Ford Mustang.
CURT 112103 is a trailer hitch designed for the Ford Mustang. It has a gross load capacity of 2,000 lbs. trailer weight and 200 lbs. tongue weight. The hitch is easy to install and can be done in 30 minutes by a professional or 60 minutes by a novice.
Here are some of the features of the CURT 112103:
- No drilling required
- Fishwire hardware
- Lower exhaust
- Designed for use with ballmount #D-20/45520
- Euro mount option available #45561 (1 7/8" ball) & #45562 (2" ball)
- Hitch weight: 26 lbs.
The CURT 112103 is a great way to add towing capacity to your Ford Mustang.
PERIODICALLY CHECK THIS RECEIVER HITCH TO ENSURE ALL FASTENERS ARE TIGHT AND ALL STRUCTURAL COMPONENTS ARE SOUND
CURT Manufacturing LLC. warrants this product to be free of defects in material and/or workmanship at the time of retail purchase by the original purchaser. If the product is found to be defective, Curt Manufacturing LLC. may repair or replace
the product at their option, when the product is returned, prepaid, with proof of purchase. Alteration to, misuse of, or improper installation of this product voids the warranty. Curt Manufacturing LLC.'s liability is limited to repair or replacement
of products found to be defective, and specifically excludes liability for incidental or consequential loss or damage.
For more information log onto www.curtmfg.com, & for helpful towing tips log onto www.hitchinfo.com
MAKE: STYLE:
MIN.30
WARNING: NEVER EXCEED YOUR VEHICLE MANUFACTURER'S RECOMMENDED TOWING CAPACITY
WEIGHT CARRYING:
INSTALLATION TIPS: INSTALLATION TIME:
INSTALLATION REQUIRES:
VEHICLE PHOTO:
HITCH ILLUSTRATION:
REPRESENTATIVE PHOTO
MAKE SURE YOUR HITCH MATCHES
LEVEL OF DIFFICULTY:
MODERATE
EASY MODERATE CHALLENGING
THE INSTALL TIME LISTED IS FOR PROFESSIONAL
INSTALLERS. IF YOU ARE HESITANT TO UNDERTAKE
THIS TASK ON YOUR OWN, CONTACT AN AUTHORIZED
CURT INSTALLER FOR ADDITIONAL ASSISTANCE.
1. BEFORE YOU BEGIN INSTALLATION, READ ALL
INSTRUCTIONS THOROUGHLY.
2. TO EASE INSTALLATION, 2 PEOPLE MAY BE
REQUIRED.
3. USING PROPER TOOLS WILL GREATLY IMPROVE
THE QUALITY OF THE INSTALL AND REDUCE THE
TIME REQUIRED.
4. NEED HELP OR HAVE SOME QUESTIONS?
CALL TECHNICAL SUPPORT AT 800.798.0813
Safety glasses should be
worn at all times while
installing this product
.
YEARS:
2011-Present FORD MODEL: MUSTANG
COUPE & CONVERTIBLE
2000
200
TRAILER WEIGHT:
TONGUE WEIGHT:
11210 INSTALLATION INSTRUCTIONS
LBS.
LBS.
12/5/2012
WARNING:
WE RECOMMEND THE USE OF 18050 STABILIZING STRAPS FOR ALL NON-TRAILER
(WHEEL-LESS) LOADS. PLEASE SEE THE CURT CATALOG OR VISIT US ONLINE AT
WWW.CURTMFG.COM FOR FURTHER INFORMATION.
PRY BAR
RATCHET
SOCKET
11/16"
13mm
TORQUE
WRENCH
SAFETY
GLASSES
REMOVE (2) RUBBER
ISOLATORS
FISHWIRE HARDWARE
NO DRILLING REQUIRED
INSTALLATION WALKTHROUGH:
For more information log onto www.curtmfg.com, & for helpful towing tips log onto www.hitchinfo.com
Parts List
DESCRIPTIONPART NUMBERQTYITEM
CARRIAGE BOLT7/16-14 x 1 1/241
.250 x .88 x 2.25" SQUARE HOLE SPACERCM-SP242
HEX FLANGE NUT7/16-1443
7/16" FISHWIRE7_16 FISHWIRE44
1. Remove the rearmost rubber isolator on both mufflers.
(See RUBBER ISOLATOR REMOVAL DIAGRAM).
2. Lower exhaust by loosening the strap which fastens the exhaust
pipes together behind the muffler and gently pulling mufflers
downward to allow access to frame rails.
JOINT TO LOOSEN
EXHAUST PIPES
(BOTH SIDES)
PASSENGER SIDE
FRAME RAIL
DRIVER SIDE
FRAME RAIL
MUFFLER
(BOTH SIDES)
ACCESS HOLE
(BOTH SIDES)
EURO MOUNT
OPTION AVAILABLE
#45561 (1 7/8" BALL)
#45562 (2" OPTION)
DESIGNED FOR USE
WITH BALLMOUNT
#D-20/45520
4
1
2
3
INSTALLATION WALKTHROUGH:
For more information log onto www.curtmfg.com, & for helpful towing tips log onto www.hitchinfo.com
3. Fishwire 7/16" x 1 1/2" carriage bolts and SP2 spacers through
access holes as shown. Do NOT pull bolts through side of frame
rails until hitch is raised up into place. (See FISHWIRE TECHNIQUE).
4. Raise hitch into position, feeding ends of fishwires through mounting
holes on hitch frame brackets. Using attached fishwires, pull bolts
through holes in side of frame rails and hitch frame brackets. Secure
with 7/16" flange nuts, as shown.
5. Torque all 7/16" hardware to 70 ft/lbs. Re-install exhaust.
Install is complete.
GROSS LOAD CAPACITY WHEN USED AS A WEIGHT CARRYING HITCH: LBS. TRAILER WEIGHT & LBS. TONGUE WEIGHT.
***DO NOT EXCEED VEHICLE MANUFACTURER'S RECOMMENDED TOWING CAPACITY.***
WARNING: ALL NON-TRAILER LOADS APPLIED TO THIS PRODUCT MUST BE SUPPORTED BY 18050 STABILIZING STRAPS.
** FAILURE TO PROPERLY SUPPORT NON-TRAILER LOADS WILL VOID PRODUCT WARRANTY**
HAVING INSTALLATION QUESTIONS? CALL TECHNICAL SUPPORT AT
1-800-798-0813
HITCH WEIGHT: LBS.
INSTALL TIME
PROFESSIONAL: MINUTES
NOVICE (DIY): MINUTES
INSTALL NOTES:
PERIODICALLY CHECK THIS RECEIVER HITCH TO ENSURE THAT ALL FASTENERS
ARE TIGHT AND THAT ALL STRUCTURAL COMPONENTS ARE SOUND.
Curt Manufacturing LLC., warrants this product to be free of defects in material and/or workmanship at the time of retail purchase by the original purchaser. If the product is found to be defective,
Curt Manufacturing LLC., may repair or replace the product, at their option, when the product is returned, prepaid, with proof of purchase. Alteration to, misuse of, or improper installation of
this product voids the warranty. Curt Manufacturing LLC.'s liability is limited to repair or replacement of products found to be defective, and specifically excludes liability for incidental or
consequential loss or damage.
2,000 200
26
30
FORD MUSTANG
12/5/2012
11210
60
Parts List
DESCRIPTIONPART NUMBERQTYITEM
CARRIAGE BOLT7/16-14 x 1 1/241
.250 x .88 x 2.25" SQUARE HOLE SPACERCM-SP2
42
HEX FLANGE NUT7/16-14
43
7/16" FISHWIRE7_16 FISHWIRE44
-NO DRILLING REQUIRED
-FISHWIRE HARDWARE
-LOWER EXHAUST
JOINT TO LOOSEN
EXHAUST PIPES
BOTH MUFFLERS
DRIVER SIDE
FRAME RAIL
PASSENGER SIDE
FRAME RAIL
MUFFLER
(BOTH SIDES)
ACCESS HOLE
ACCESS HOLE
TOOLS REQUIRED
PRY BAR
RATCHET
11/16" SOCKET
TORQUE WRENCH
1. Remove the rearmost rubber isolator on both mufflers. (See RUBBER ISOLATOR REMOVAL DIAGRAM)
2. Lower exhaust by loosening the strap which fastens the exhaust pipes together behind the muffler and
gently pulling mufflers downward to allow access to frame rails.
3. Fishwire 7/16 x 1 1/2" carriage bolts and SP2 spacers through the access holes as shown. Do NOT pull bolts
through side of frame rail until hitch is raised up in place. (See FISHWIRE TECHNIQUE)
4. Raise hitch into position, feeding ends of fishwires through mounting holes on hitch frame brackets. Using
attached fishwires, pull bolts through holes in side of frame rails and hitch frame brackets. Secure with 7/16"
flange nuts, as shown.
5. Torque all 7/16" hardware to 70 ft/lbs. Re-install exhaust.
1
2
3
4
DESIGNED FOR USE WITH
BALLMOUNT #D-20/45520
EURO MOUNT OPTION
AVAILABLE #45561 (1 7/8" BALL)
& #45562 (2" BALL)
-
1
-
2
-
3
-
4
CURT 112103 is a trailer hitch designed for the Ford Mustang. It has a gross load capacity of 2,000 lbs. trailer weight and 200 lbs. tongue weight. The hitch is easy to install and can be done in 30 minutes by a professional or 60 minutes by a novice.
Here are some of the features of the CURT 112103:
- No drilling required
- Fishwire hardware
- Lower exhaust
- Designed for use with ballmount #D-20/45520
- Euro mount option available #45561 (1 7/8" ball) & #45562 (2" ball)
- Hitch weight: 26 lbs.
The CURT 112103 is a great way to add towing capacity to your Ford Mustang.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Curt Manufacturing 11215 Owner's manual
-
-
-
-
-
Reese 67509† Installation guide
-
Meyer Products FHK31038 Installation guide
-
idh by St. Simons 18050-015 Installation guide
-
