Taurus HOME AC 351 User manual

Category
Toys
Type
User manual
English
Portable Air Conditioner
AC35S - AC 350KT - AC 350 RVKT
Dear customer,
Many thanks for choosing to purchase a ALPATEC brand
product.
Thanks to its technology, design and operation and the
fact that it exceeds the strictest quality standards, a fully
satisfactory use and long product life can be assured.
Description
Control Panel
Remote control
- Read these instructions carefully before switching on
the appliance and keep them for future reference. Failure
to follow and observe these instructions could lead to an
accident.
A Top Cover
B Air Outlet grill
C Panel control
D Housing
E Castor
F Handle
G Power cord
H Drain port
I Up lter frame
J Protective net
K Down lter frame
L Water plug
M Remote control
N Exhaust hose
O Window kit
P Hose adaptor
A1 On/Off power
A2 Mode
A3 Fan Speed
A4 LED lamp
A5 Display area
A6 Timer
A7 Up and down buttons
A Power
B Mode
C Fan function
D Timer
E Auto swing
F Auto clean
G Up and down function
Safety advice and warnings
- This appliance can be used by
children aged from 8 years and above
and persons with reduced physical,
sensory or mental capabilities or lack of
experience and knowledge if they have
been given supervision or instruction
concerning use of the appliance in a
safe way and understand the hazards
involved.
- This appliance is not a toy. Children
should be supervised to ensure that
they do not play with the appliance.
- Cleaning and user maintenance shall
not be made by children unless they are
supervised.
- Only use the appliance with the specific
electric connector provided.
- If the connection to the mains has been
damaged, it must be replaced, take the
appliance to an authorised technical
support service. Do not attempt to
disassemble or repair the appliance by
yourself in order to avoid a hazard.
- Ensure that the voltage indicated on the rating label
matches the mains voltage before plugging in the
appliance.
- Connect the appliance to a base with an earth socket
withstanding a minimum of 16 amperes
- The appliance’s plug must t into the mains socket
properly. Do not alter the plug. Do not use plug adaptors.
- Do not force the power cord. Never use the power cord
to lift up, carry or unplug the appliance.
- Do not wrap the power cord around the appliance.
- Do not clip or crease the power cord.
- Check the state of the power cord. Damaged or tangled
cables increase the risk of electric shock.
- Do not touch the plug with wet hands.
- Do not use the appliance if the cable or plug is damaged.
- If any of the appliance casings breaks, immediately
disconnect the appliance from the mains to prevent the
possibility of an electric shock.
- Do not use the appliance if it has fallen on the oor, if
there are visible signs of damage or if it has a leak.
- Do not place the appliance where it can reach the
sunlight.
- Place the appliance on a horizontal, at, stable surface
away from heat sources and contact with water (splashes
etc.)
- Do not use or store the appliance outdoors.
Use and care:
- Fully unroll the appliance’s power cable before each use.
- Do not use the appliance if the on/off button does not
work.
- Do not move the appliance while in use.
-Do not remove the castors of the appliance
- Use the appliance handle, to catch it or move it.
- Do not turn the appliance over while it is in use or
connected to the mains.
- Unplug the appliance from the mains when not in use and
before undertaking any cleaning task.
- This appliance is for household use only, not professional,
industrial use.
- This appliance should be stored out of reach of children
and/or the disabled.
English
- Do not expose the appliance to extreme temperatures.
- Never leave the appliance connected and unattended if
is not in use. This saves energy and prolongs the life of
the appliance.
- Any misuse or failure to follow the instructions for
use renders the guarantee and the manufacturer’s
liability null and void.
Installation
- Be sure to remove all packaging material from inside
the appliance.
- Respect the legal provisions concerning safety dis-
tances from other elements such as pipes, electrical
connections, etc.
- Ensure that the appliance is level with respect to the
oor.
- The appliance requires suitable ventilation in order to
work properly. Leave a space of 50cm between walls or
other obstacles.
- Do not cover or obstruct any of the openings of the ap-
pliance.
- Do not cover or obstruct the sides of the appliance, and
leave a minimum space of 40cm front other walls, ceiling.
- The plug must be easily accessible so it can be dis-
connected in an emergency.
- To achieve the highest efciency from the appliance it
should be situated in a place where the atmospheric tem-
perature is between 12 and 32ºC.
- Ensure that the extraction pipe remains in a horizontal
position.
- Do not add new sections to the extraction tube provided,
as it could cause the appliance to malfunction.
Assemble the hose adaptor.
Don´t push too hard to prevent damage.
Assembly of the exhaust hose
Lengthen one head of the hose, screw it into the unit
anti-clockwise.
-The same way to connect the hose to the assembled
adaptor( At least three circles)
Installation of window kits
Partially open the window and then x the window kits to
the window.
The window kits can be installed on most normal and ver-
tical windows, and it is adjustable.
Fix the other end of the heat-exhausted hose to the
air-outlet window kit.
Instructions for use
Before use:
- Remove the appliance’s protective lm.
- Before using the unit, please keep it upright at least 2
hours.
Use
- Unroll the cable completely before plugging it in.
- Connect the appliance to the mains.
- You will hear a beep, the unit is in stand by status.
- Digital screen will indicate temperature (Range:
535°C),if ambient temperature above 35°C,screen will
show “H”. If it is below 5°C, it will indicate “L” and the unit
will enter standby status.
- When press the ON/OFF button, the unit will enter in
cooling mode (setting temperature 24ºC), high speed fan.
- Press again , unit will shut off and play shut off beep.
- Press the MODE button to choose Cooling, Heating (only
for the model AC 350 RVKT) Fan or dehumidifying mode.
Fan speed:
- Under the cooling and the fan mode, the speed goes
as follow:
- Low Fan (F1)→Middle Fan (F2)→High Fan (F3)→Low
Fan (F1)
- Under the dehumidifying mode, fan is working in low
speed.
Timer function:
- The appliance’s operating time can be controlled.
- To program the operating time simply select it using
pressing the timer icon.
- Timer icon will ash “88” area indicates 24:00
- You can set your time through UP and DOWN buttons.
- The HOUR number will change from 1,2,3…24; the
Minute number will change from 10, 20,30…50.
- Auto-shut-off timer is only available when the unit on.
- Auto-run timer is only available when the unit is off.
After timer setting accomplishes effectively, TIMER icon
will keep on ashing until setting time is due. If set again,
history record will be cleared.
1.6
- Up and Down button : can set temperature and timer.
- Under cooling mode, the setting temperature ranges
from 1830°C.
Auto swing:
- Press this button to control the swing function.
Cooling function:
- Press the button MODE until the word Cool appear on
the control panel.
- Press the up or down button to increase or decrease
the temperature.
English
- NOTE: If the temperature of the room is higher of the
selected one, the appliance will not start working.
Fan function:
- Press the button MODE until the word Fan appear on
the control panel.
-You can choose the speed fan: Low-middle-high
Dehumidifying function:
- Press the button MODE until the word Dry appear on
the control panel
- On the dehumidifying mode, the fan is working in low speed.
Anti-freezing protection control
(only for the model AC 350 RVKT):
- Under anti freezing function,the heat light will ash
Anti-heating protecting
(only for the model AC 350 RVKT):
- Under heating mode, the compressor and motor
will stop work until the temperature of the machine
automatically recover to ordinary heating status.
Compressor delay-protection
Except for the rst power-on, the compressor can start
at once. In other cases, the compressor runs under 3
minutes delay protection.
Water tank full protection:
- When the water level in the bottom water plate is above
the warning level, the unit will alert automatically and “FL”
will ashes on LCD.
-Please discharge water in the machine according to
chapter “water drainage”.
Stand-by function:
- In order to save energy, the appliance passes to stand-
by after 10 seconds if the user does not use it.
- To turn it on again, you simply have to press the on/
off button.
Once you have nished using the appliance:
- Stop the appliance by releasing the pressure on the on/
off button.
- Unplug the appliance from the mains.
- Remove the water from the water tank.
- Clean the appliance.
Carry handle/s:
- This appliance has a handle on the side of the body,
which facilitates comfortable transport.
Water drainage:
Manual drainage:
- When the water tank is full and unit stop working, please
shut off the unit and unplug .
- Do not move the model sharply, or the water will split out
from water received plate.
- Use a water container to take water under the water
plug.
- Screw off the water plug and unplug the water blocker,
water will come out the water container.
- Stuff up the water blocker and screw down the water plug.
Continuous drainage:
- Screw off the water plug and unplug the water blocker.
-Use water pipe to connect the water outlet. Lead the pipe
to the outside or washroom.
NOTE: This method can be done only if there is no water
in the water received plate.
-This model have self evaporative function, under cooling
mode, please do not use continue drainage to get better
cooling effect.
Cleaning
- Disconnect the appliance from the mains and allow it to cool
before undertaking any cleaning task.
- Clean the electrical equipment and the mains connection
with a damp cloth and dry. DO NOT IMMERSE IN WATER
OR ANY OTHER LIQUID.
- Clean the equipment with a damp cloth with a few drops of
washing-up liquid and then dry.
- Do not use solvents, or products with an acid or base pH
such as bleach, or abrasive products, for cleaning the ap-
pliance.
- Do not let water or any other liquid get into the air vents to
avoid damage to the inner parts of the appliance.
- Never submerge the appliance in water or any other liquid or
place it under running water.
- If the appliance is not in good condition of cleanliness, its
surface may degrade and inexorably affect the duration of the
appliance’s useful life and could become unsafe to use.
Air lter cleaning
- Clean the air lters every 2 weeks. If the air lter is
blocked with dust, the efciency will reduce.
- Pull out up and down lter as below pictures
- Wash the air lters by immersing it gently into warm wa-
ter with a neutral detergent, rinse it and dry it thoroughly
in a shaded place.
- Install air lters carefully after cleaning the lters.
After Season Maintenance:
- Pull out the plug in drainage hole and empty the water
received plate, or drain out the water by leaning the unit,
then shift the unit mode to Fan mode, and press the but-
ton for 5 seconds till it low fan speed.
-Keep this mode for half day till the conduit is dried. Doing
like this can keep the inner unit dried and not go moldy.
- Turn off the unit and pull out the plug.
- Coil the wire and bind it together, then put it into the
accessories room.
- Separate the air-exhausted pipe and safely keep it.
- Put the unit into a plastic bag, then keep it in a dried
place.
- Take out the batteries of remote control and safely keep
them.
* All accessories can be put in the accessories room on
the back of the unit.
English
Specications:
Voltage; 220-240V
Frequency: 50Hz
Dehumidifying capacity: 33.6L/j
Airow: 453m3/h4
Exhaust pipe diameter: 1.5m/150mm
Working temperature: between 7-40ºC
Timer: 24 hours
Class I
Refrigerant gaz: R410A
Product size: 47*84*37cm
Product weight: 36kg
For EU product versions and/or in case that it is requested in your country:
Anomalies and repair
- Take the appliance to an authorised technical support
service if product is damaged or other problems arise.
Do not attempt to disassemble or repair the appliance
yourself as this may be dangerous.
- If any anomaly is detected, check the following table:
Anomalies Causes Solutions
The unit does not work No power supply
Water full indicator illuminate
Timer function is active
Room temperature too low or too high
Turn on the appliance
Drain out the inner stored water
Cancel timer function
Suggesting ambient temperature between 7-40ºC
The unit does not seem to
perform
Indirect sunlight
Window or doors open
Filter is very dirty
Air inlet or air outlet is blocked
Room temperature is lower than the setting
one
Draw the curtains
Close windows and turn on another air conditioner
Clean or change the air lter
Clean out the stemming
Change the temperature setting
The unit noise is high The unit is not put on a at surface Put the unit on a at and stable surface that can
support its weight
Compressor does not work Heat exceeded protection is active Re start the unit 3 minutes later till the temperature
low down
Remote control does not
work
The distance is too far
The batteries run out
Let the remote control near the unit
Change the batteries
E1 on LCD Coil temperature is abnormal Check coil temperature sensor or relevant circuit
Contact the technical support
E2 on LCD Room temperature is abnormal Check the room temperature sensor.
Contact the technical support
E3 on LCD No refrigerant or there is very few refrigerant Check leakage, wielding, vacuum pump and contact
the technical support
P2 on LCD The water tank is full Drain out the water
This appliance complies with Directive 2006/95/EC on
Low Voltage and Directive 2004/108/EC on Electromag-
netic Compatibility.
Ecology and recyclability of the product
- The materials of which the packaging of
this appliance consists are included in a col-
lection, classication and recycling system.
Should you wish to dispose of them, use the
appropriate public recycling bins for each
type of material.
- The product does not contain concentra-
tions of substances that could be considered harmful to
the environment.
- This appliance contains, or could contain, oil. Remember
that one should abide by the regulations concerning the
elimination of this type of contaminant.
- This symbol means that in case you wish to dispose
of the product once its working life has ended, take it to
an authorised waste agent for the selective collection of
Waste from Electric and Electronic Equipment (WEEE).
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28

Taurus HOME AC 351 User manual

Category
Toys
Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI