Package Checklist
Ÿ SP3010LD 56K Data/Fax/Voice Modem
PCI Card
Ÿ Driver & Application software CD-ROM
Quick Installation Guide
Features
SP3010LD supports the following
communication standards. ITU-T is also
known as CCITT.
Data
Ÿ V.92 (Lite)
Ÿ V.90, V.34, V.32bis, V.32,
Ÿ V.22bis, V.21,
Ÿ V.22
Ÿ Bell 103 & 212A
Ÿ V.44, V.42bis & MNP 5 (Data compress)
Ÿ V.42 & MNP2-4 (Error correction)
Fax
Ÿ V.17 (14,400bps)
Ÿ V.29 (9,600bps)
Ÿ V.27 (4,800bps)
Voice
Ÿ Voice/Audio mode
Ÿ Speaker/Phone jack
Part 1. Hardware Installation
With the power to your PC disconnected,
remove the PC’s casing. Press the modem
card firmly into the PCI slot, and secure it
with screws to your PC. Reinstall the casing
on your PC.
Part 2. Installation Procedures
Driver installation for Windows O/S
The following instructions apply for
Windows 98, 98SE, ME, NT, 2000 and XP.
Some of the screens may differ slightly
across operating systems.
1. Once the device is properly connected
to your computer, Windows O/S will
automatically detect the new hardware
device. Click Next.
2. Select Search for the best driver for
your device (Recommanded). Click
Next.
3. Insert the device driver disk into your
CD-ROM. Select Specify a location,
and click Browse to search for driver
files and open it, e.g., (CD-ROM)
D:\DRIVER\Winxx. Click Next.
4. Windows found the driver of this modem.
Click Next.
5. Click Finish to complete the installation.
6. Wait until the drivers were installed
automatically.
Part 3. Update Driver
In some case, Windows operating system
will get the default driver and install the
modem automatically. Please follow the
process below to update the driver of your
modem.
1. Find the modem from Start à Settings
à Control Panel à System à
Hardware à Device Manager à
Modem. Double-click the modem
description, e.g., Intel(R) 536EP Modem.
Click Properties.
2. Select Driver and click Update Driver.
3. The wizard will search for new driver.
Select Don’t search. I will choose the
driver to install and click Next.
4. Click Browse to search for driver files
and open it, e.g., (CD-ROM)
D:\DRIVER\WINxx. Click OK and then
click Next.
5. Click Finish.
Part 4. Modem Dialing Location
Following the instructions below, you can
change the dialing location.
1. In Windows 2000/XP, Click Start à
Settings à Control Panel à Phone
And Modem Options à Under Dialing
Rules click Edit, and then you can
change your location.
2. In Windows ME/NT/98, click Control
Panel à Modem à Under General
click Dialing Properties, and then you
can change your location.
P/N: 2300-0237
FCC Certifications
This device complies with Part 15 of the FCC
rules. Operation is subject to the following
two conditions:
(1) This device may not cause harmful
interference, and (2) This device must accept
any interference received, including
interference that may cause undesired
operation.
CE Mark Warning
This is a Class B product. In a domestic
environment, this product may cause radio
interference, in which case the user may be
required to take adequate measures.
Installation Guide
56K Data/Fax/Voice Modem
Model No. SP3010LD
http://www.micronet.info
/