Whirlpool TVF 85C 6H (EX) User guide

Brand: Whirlpool

Model: TVF 85C 6H (EX)

Category: Electric laundry dryers

Type: User guide

Contents

TUMBLE DRYER

TVF 85C

Instruction booklet

! Keep this instruction booklet on hand in order to refer to it when necessary. Take it with you when you move, and

should you sell this appliance or pass it on to another party, make sure that this booklet is supplied along with the

dryer so that the new owner may be informed about warnings and suggestions on how the appliance works.

! Read these instructions carefully; the following pages contain important information on installation and suggestions

on how the appliance works.

This symbol reminds you to read this booklet.

Important information, 2

Installation, 3-4

Where to put your dryer

Ventilation

Electrical connection

Levelling your dryer

Before you start using your dryer

Dryer description, 5

The front

The back

Control panel

The Display, 6

Start and programmes, 7-11

Choosing a programme

Programmes and tables

The controls

Laundry, 12-13

Sorting your laundry

Wash care labels

Special clothing items

Drying times

Warnings and Suggestions, 14

General safety

Saving energy and respecting the environment

Maintenance and Care, 15

Switching off the electricity

Cleaning the filter after each cycle

Check the drum after each cycle

Cleaning the dryer

Troubleshooting, 16

Service, 17

Disposal

Español, 35

Português, 52

English, 1

Français, 18

Important Information

! You MUST clean the fluff filter after EVERY drying

cycle.

Fluff Filter...

! Failure to clean the filter after EVERY drying cycle will affect the drying performance of your machine.

- It will take longer to dry and as a result will use more electricity during drying.

STEP 1.

Open the door of your

dryer.

STEP 2.

Pull out the filter (using

the two finger grips).

STEP 3.

Open the filter and clean

any fluff deposits from

the filter mesh.

For your Venting dryer to operate efficiently, you must follow the regular maintenance schedule shown below:

STEP 4.

Refit the filter, with the

curved side towards you.

STEP 5.

Make sure the filter is

pushed fully home.

- NEVER run the dryer

without the filter in position.

! You MUST clean fluff build up around the filter housing and the vent tube periodically, EVERY two or three months:

- Check the vent tube and any permanent venting fixture to make sure that there has been no accumulation

of fluff or lint, and remove it.

- Remove lint that collects around the filter and the outlet vents.

Installation

Permanent venting

In conjunction with the vent tube we recommend

using a Wall/Window Vent Kit, available at a retail

location or the nearest Spare Parts Dealer.

Wall mounting

1. Leave an opening in

the wall to the left of the

dryers proposed position.

2. Keep the tube as short

and straight as possible

to prevent condensed

moisture from backing up

into the dryer.

3. Similarly, the duct in

the wall should slope

downwards towards the

outside.

Window mounting

1. With a stacked dryer

the hole in the window

should ideally be made

below the vent.

2. The tube should be

kept as short as possible.

Depending on how often you use your dryer, it is

essential that areas A and B are checked periodically

to remove lint or debris.

The vent tube adaptor must be fitted securely thus

preventing any humid air from being emitted back into

the room.

! The Dryer should not be pushed so far back that the

tube adaptor is pulled out of position or the tube is

squashed or bent.

! The tube should be kept clear of the air intake vent

and kinks or ‘U’ bends must be avoided as these will

obstruct the tube or trap condensation.

Where to put your dryer

●

Place your dryer at a distance from gas ranges,

stoves, heaters, or cook tops because flames can

damage the appliance.

●

If you are going to install the

appliance under a work

counter, be sure to leave a

10mm space between the

top and any other objects on

or above the machine and a

15mm space between the

sides and lateral furnishings

or walls. This is to ensure

proper air circulation. Make sure that the back

vents are not obstructed.

●

Make sure you put your dryer in an environment

that is not damp and has proper air circulation

throughout, the dryer will not operate efficiently in

an enclosed space or cupboard.

! We do not recommend that the dryer is installed in a

cupboard but the dryer must never be installed

behind a lockable door, a sliding door or a door with a

hinge on the opposite side to that of the dryer door.

Ventilation

The Dryer dries your laundry by drawing in cool, clean

and relatively dry air, heating it, and then distributing it

through the clothes as they are gently tumbled. For

optimum performance, the moist air is then blown out

through a vent tube at the back of the dryer.

When the dryer is in use, there has to be adequate

ventilation to avoid the back flow of gases into the room

from appliances burning other fuels, including open fires.

Mobile venting

A vent tube must always be fitted when the dryer is

used in conjunction with Mobile Venting.

The tube must be fitted securely into the back of the

dryer (see Dryer Description). If possible, it is always

best to connect the tube to a permanent

outlet close to the dryer. If permanent installation is

not possible, the dryer will work just as well with the

tube passing through a partly-opened window.

! Ensure that the end of the tube is not directed

toward the air intake vent at the rear of the dryer.

! The vent tube should not exceed 2.4 metres in

length and should be kept free of any possible

accumulation of fluff, lint and water by shaking it out

frequently. Always ensure that the tube is not

squashed.

Minimum gap 10mm

Minimum gaps

15mm

! Do not use extension cords.

! The power cord must not be bent or squashed.

! The power supply cord should be checked periodically

and replaced by a cord specially prepared for this dryer

and fitted only by authorised technicians (see

Service). New or longer power cords are supplied at

an extra charge by authorised dealers..

! The manufacturer denies any responsibility should

any of these rules not be followed.

! If in doubt about any of the above consult a qualified

electrician.

Levelling your dryer

The dryer must be installed level for correct operation.

When you have installed

your dryer in its final

location check that it is

level first side to side,

then front to back.

If the dryer is not level,

use a wooden block to

support it while adjusting

the two front legs up or

down, until your dryer is

level.

Before you start using your dryer

Once you have installed your dryer and before you

use it, clean the inside of the drum to remove any

dust that could have accumulated during transport.

Open window venting

The end of the tube

should be directed

downwards, to prevent

warm moist air from

condensing in the room or

in the dryer.

! Ensure that the dryer is adequately ventilated and

that the end of the vent tube is not directed towards

the air intake duct.

! The vent tube must always be fitted for optimum

performance.

! Make sure that the vent tube and air intake vents are

not obstructed or blocked.

! The dryer must not recycle exhaust air.

! Misusing a tumble dryer may create a fire hazard.

! Do not discharge exhaust air into a flue which is

used for exhaust fumes from other appliances that

burn gas or other fuels.

! Do not discharge exhaust air into an extraction

system or any duct with an extractor fan. This will

affect the way the thermal controls operate and can

result in a fire hazard.

Electrical connections

Make sure of the following before you insert the plug

into the the electrical socket:

●

The socket must be grounded.

●

The socket must be able to sustain the machines

maximum power, which is indicated on the rating

label (see Dryer Description).

●

Power voltage must be within the values indicated

on the rating label (see Dryer Description).

●

The socket must be compatible with the dryers

plug. Should this not be the case, replace the

plug or the socket.

! The dryer must not be installed outdoors, even if the

space is sheltered. It can be very dangerous if it is

exposed to rain or storms.

! Once installed, the dryers electrical wire and plug

must be within easy reach.

Installation

Control panel

Dryer Description

PROGRAMME

knob

Display Unit &

Selection Buttons

START/PAUSE

Button & Light

CHILD LOCK

Button & Light

HEAT LEVEL

Button & Lights

ON/OFF

Button

CLEAN FILTER

Icon

Indicator

OPTION

Buttons & Lights

The ON/OFF button : If the dryer is running and

this button is pressed and held for more that 3 seconds

the dryer is turned off, it counts down 3, 2, 1, Off and

the programme is then cancelled.

Press and hold for more than 3 seconds and the dryer

reactivates.

The PROGRAMMES knob sets the programme: rotate

it until the indicator is pointing to the programme you want

to select (see Start and Programmes).

The OPTION buttons/lights select available options for

your selected programme. The lights indicate that the

option has been selected. If an option is not available

the buzzer will beep three times (see Start and

Programmes).

The START/PAUSE button/light starts a selected

programme. When you press this button there will be

one beep and the progress lights will flash to confirm

the action. When a programme is running, holding this

button in pauses the programme and stops the dryer.

The light is green when programme is running, flashing

amber if the programme has been paused or flashing

green if on standby waiting to start a programme (see

Start and Programmes).

Note: This light also flashes amber during the Post

Care phase of a programme.

The Display Unit gives an indication of the drying or

delay time together with icons that light to give warning

information and show the status of your programmes

progress. The three buttons below the display select

‘Automatic’ or ‘Timed Dry’ and if required a delayed

start (see Start and Programmes or The Display).

The CLEAN FILTER icon : gives a reminder

before every programme, that it is essential to clean

the filter every time the dryer is used (see Maintenance

and Care).

The CHILD LOCK button/light : Press and hold this

button after selecting your programme and any options,

the light turns on. This prevents the programme

settings from being changed. When the light is lit, the

other buttons are disabled. Hold the button to cancel

and the light will go out.

Control Panel

Drum

Model & Serial

numbers

Filter

The front The back

Air Intake Vent

Vent Tube fitted here

Caution: Hot!

Rating plate

The Display

The Display has three main functions, each with its corresponding button.

After selecting a programme that has a Sensor Dry option, press and release the button until the required

dryness sensing level is displayed. If the sensing option is not available with your selected programme, the

display will flash and the buzzer will beep three times.

! Some sensing programmes do not have all five dryness level options available.

Dryness levels:

Damp Dry: Dries your items ready to be ironed using a machine or rotary ironer.

Iron Dry: Dries your items ready to be ironed with a hand iron.

Hanger Dry: Dries your clothes ready to be hanged for final drying.

Use this programme if you do not need the items to be fully dry as it uses less energy.

Cupboard Dry: Dries your items ready to be put away.

Extra Dry: Dries your clothes ready to be worn.

Timed Dry

Dryness Sensing Levels

Delay Timer

24h

OFF

9.59

After selecting a programme that has a Delay Timer option, a delay start time can be selected.

Each press of the Delay Timer button advances the delay setting in 30 minutes increments from

to and then increments from to then and then after five seconds cancels the

delay.

For delays of 10 hours or more the display counts down the time in hours until 10 hours, then the

display shows and then continues to count down in minutes.

For delays 9 hours or less the display shows hours and minutes and then counts down in minutes for

all of the delay.

After the START/PAUSE button is pressed the delay time can be changed or cancelled.

When the delay period finishes the delay icon is off and the Time to End is displayed.

0:30

9:30

Time to End

If the delay icon is off the time displayed is the Time to End for the programme running.

When timed programmes are selected the time displayed throughout the cycle is the actual time remaining.

When Automatic programmes are selected the time displayed is an estimate of the time remaining. When the

programme is selected the display shows the time required to dry a full load, after around 10 minutes the controller

calculates a better estimate of the cycle time and this is updated during the programme.

The Time to End is displayed in hours and minutes and counts down each minute.

The colons between the hours and minutes in the display flash to show the time is counting down.

The display also shows if there is a problem with your dryer, if this occurs the display will show F followed by a fault

code number, the three option lights and the START/PAUSE light will also flash amber (see Troubleshooting).

After selecting a programme that has a Timed Dry option, press the button and the Timed Dry icon will

light, the display will reduce the selected time each time you press and release this button (see Start and

Programmes). Each programme that has a timed option has different times available and the selection of

up to 11 drying times will also depend on the heat setting that your have selected.

Each press of the button decreases the drying time.

If you change your mind, press the Sensor Dry button and the sensing level options are available.

If the Timed Dry option is not available the Timed Dry icon will flash and the buzzer will beep three times.

The selected time remains displayed after the programme starts and can be changed during the

programme if you wish.

10h

Choosing a programme

1. Plug the dryer into the electrical socket.

2. Sort your laundry according to fabric type (see

Laundry).

3. Open the door and make sure the filter is clean

and in place (see Maintenance).

4. Load the machine and make sure items are not

in the way of the door seal. Close the door.

5. If none of the lights are on: Press the ON/OFF

button .

6. Choose a programme by checking the Programmes

Guide (see Programmes) as well as the indications

for each type of fabric (see Laundry).

- Select a programme by rotating the

PROGRAMMES knob.

7. Choose Timed Drying or Dryness Levels option:

- If Timed Dry press and release the Timed

button until the required time is displayed.

or - To change from default dryness setting, press

and release the Sensor Dry button until the

required level is indicated (see The Display).

8. Set a delay time and other options if necessary.

9. The START/PAUSE light is flashing green:

- press the START/PAUSE button to begin.

The green light stops flashing.

During the drying programme, you can check on

Start and Programmes

Bed & Bath

●

This is a programme for cotton towels and sheets.

●

The duration of this programme will depend on the size of the load, the dryness setting selected and the spin

speed used in your washer (see Laundry).

●

Loads dried using the Extra Dry setting are usually ready to use, the edges or seams may be slightly damp

especially on large items. If this is the case, try opening them out and running the programme again for a short

period.

Cottons

●

This is a programme for cotton items.

●

The duration of this programme will depend on the size of the load, the dryness setting selected and the spin

speed used in your washer (see Laundry).

Note: This tumble dryer, in compliance with new energy saving regulations, is fitted with an automatic standby

system which is enabled after about 30 minutes if no activity is detected. Press and hold the ON/OFF button until

the dryer reactivates.

your laundry and take out items that are dry

while others continue drying. When you close

the door again, press the START/PAUSE button in

order to resume drying.

(When the door is opened the START/PAUSE light

will flash Amber, after the door is closed and the

START/PAUSE button pressed, the START/PAUSE

light will stop flashing and show green.)

Note: During the Post Care phase this light

flashes Amber.

10. At the end of the drying cycle the display shows

END and either :

- The buzzer will beep 3 times to let you know

that your programme is complete. (Note: If

the SOUND option was selected the buzzer

beeps 3 times every 30 seconds for 5

minutes).

or - If you have selected the Crease Care option

and you do not take the items out immediately,

the items will tumble occasionally for 10

hours or until you open the door, the buzzer

will then beep 3 times to confirm the

programme is completed.

11. Open the door, take the laundry out, clean the filter

and replace it (see Maintenance).

12. Unplug the dryer.

Programme Options available

1 Cottons

4 Synthetics

6 Synthetics Quick Dry

5 Cottons Quick Dry

3 Bed & Bath

ESSENTIAL PROGRAMMES - Programmes Table

Shirts

✗

✓ ✗

✗

✓

Dryness Levels available

(default highlighted )

Delay Timer

*Crease Care

Sound

Heat Level

Timed Dry

Sensor Dry

Damp Dry

Iron Dry

Hanger Dry

Cupboard Dry

Extra Dry

●

An Automatic programme

●

An Automatic programme

*YOU CANNOT SELECT BOTH

CREASE CARE AND SOUND OPTIONS

- High

- Medium

- Low

- High

- Medium

- High

- Medium

- Low

Start and Programmes

Jeans

●

This is a programme for jeans made from denim cotton. Before drying your jeans turn the front pockets inside out.

●

It can be used for load sizes up to 3kg (approximately 4 pairs).

●

Do not mix dark and light coloured items.

●

It can also be used on other garments made from the same material, such as jackets.

●

The duration of this programme will depend on the size of the load, the dryness setting selected and the spin

speed used in your washer.

●

Loads dried using the Extra Dry setting are usually ready to wear, the edges or seams may be slightly damp. If

this is the case, try turning the jeans inside out and running the programme again for a short period.

! We do not recommend that you use this programme if your jeans have elastic waist bands, studs or embroidery.

Shirts

High heat option

●

This is a programme for shirts made from cotton.

●

It can be used for load sizes up to 3kg (approximately 10 shirts).

●

The duration of this programme will depend on the size of the load, the dryness setting selected and the spin

speed used in your washer.

Medium heat option

●

This is a programme for shirts made from synthetic materials or a mixture of natural and synthetic materials, such

as polyester and cotton.

●

It can be used for load sizes up to 3kg (approximately 14 shirts).

●

The duration of this programme will depend on the size of the load, the dryness setting selected and the spin

speed used in your washer.

Loads dried using the Cupboard Dry setting are usually ready to wear, the edges or seams may be slightly damp. If

this is the case, try turning the shirts inside out and running the programme again for a short period.

Synthetics

●

This is a programme for items of Synthetic or Synthetic/Cotton mixtures.

●

The duration of this programme will depend on the size of the load, the dryness setting selected and the spin

speed used in your washer (see Laundry).

Quick Dry Cottons

●

This programme is for small loads made from cottons, maximum 1kg.

●

Your drying time is very much reduced with a huge time saving up to 53%.

Quick Dry Synthetics

●

This programme is for small loads made from synthetics, maximum 1kg.

●

Your drying time is very much reduced with a huge time saving up to 50%.

Programme Options available

7 Jeans

10 Delicates (eg. Acrylics)

12 Baby cycle

11 Lingerie

9 Silk

EXCLUSIVE PROGRAMMES - Programmes Table

8 Wool

✗

✓

✗

✓

✗

✓

✗

✓

✗

✓

✗

✓

✗

✓

Dryness Levels available

(default highlighted )

Delay Timer

*Crease Care

Sound

Heat Level

Timed Dry

Sensor Dry

Damp Dry

Iron Dry

Hanger Dry

Cupboard Dry

Extra Dry

●

An Automatic programme

*YOU CANNOT SELECT BOTH CREASE CARE AND SOUND OPTIONS

Start and Programmes

Wool Programme

●

This is a programme for tumble dryer safe garments marked with the symbol .

●

It can be used for load sizes up to 1kg (approximately 3 sweaters).

●

We recommend that garments are turned inside out before drying.

●

This programme will take about 60 minutes, but may take longer depending on the size and density of the load

and the spin speed used in your washer.

●

Loads dried using this programme are usually ready to wear, but on some heavier garments the edges may be

slightly damp. Allow these to dry naturally as over-drying could damage garments.

! Unlike other materials, the mechanism of wool shrinkage is irreversible; i.e. it will not stretch back to original size and

shape.

! This programme is not suitable for Acrylic garments.

Baby Programme

●

This is a programme for drying your baby’s small delicate items of clothing and bedding (Cotton and Chenille)

and for drying your delicate clothes.

●

DO NOT dry items such as bibs and nappy pants with plastic coverings.

●

It can be used for load sizes up to 2kg.

●

The duration of this programme will depend on the size of the load, the dryness setting selected and the spin

speed used in your washer.

●

Loads dried using the Cupboard Dry setting are usually ready to use, but on some garments the edges may be

slightly damp. If this is the case, try opening them out or turn items inside out and running the programme again for

a short period.

Lingerie

●

This is a programme for drying your very delicate lingerie, including silk.

●

It can be used for load sizes up to 1kg, close all hooks, buttons or zips before drying.

●

The duration of this programme will depend on the size of the load, the dryness setting selected and the spin

speed used in your washer.

●

Loads dried using the Cupboard Dry setting are usually ready to use, but on some garments the edges may be

slightly damp. If this is the case, try opening them out or turn items inside out and running the programme again for

a short period.

Delicates

●

This is a programme for drying your delicate clothes ie. Acrylics.

●

It can be used for load sizes up to 2kg.

●

The duration of this programme will depend on the size of the load, the dryness setting selected and the spin

speed used in your washer.

●

Loads dried using the Cupboard Dry setting are usually ready to use, but on some garments the edges may be

slightly damp. If this is the case, try opening them out or turn items inside out and running the programme again for

a short period.

Silk

●

This is a programme for drying your delicate silk.

●

It can be used for load sizes up to 0.5kg.

●

The duration of this programme will depend on the size of the load, the dryness setting selected and the spin

speed used in your washer.

●

Loads dried using the Cupboard Dry setting are usually ready to use, but on some garments the edges may be

slightly damp. If this is the case, try opening them out or turn items inside out and running the programme again for

a short period.

Start and Programmes

Easy Iron Programme

‘Easy Iron’ is a short 10 minute programme (8 minutes of heat followed by a 2 minute cool tumble period) which

fluffs the fibres of clothing that have been left in the same position/location for an extended period of time. The cycle

relaxes the fibres and makes them easier to iron and fold.

! ‘Easy Iron’ is not a drying programme and should not be used for wet articles of clothing.

For best results: 1. Do not load more than the maximum capacity. These numbers refer to the dry weight:

Fabric Maximum load

Cotton and Cotton mixtures 2.5kg

Synthetics 2kg

Denim 2kg

2. Unload the dryer immediately after the end of the programme, hang, fold or iron the articles

and put them away in the closet. Should this not be possible repeat the programme.

The ‘Easy Iron’ effect varies from one fabric to the next. It works well on traditional fabrics like Cotton or Cotton mix,

and less well on acrylic fibres and on materials such as Tencel®.

Cuddly Toy Programme

With this programme you can remove dust easier and wash the cuddly toys more often because the drying time is

very much reduced compared to drying in the open air. It is a delicate drying cycle that dries at low temperature

and with soft mechanical action to maintain at best the original look and shine of the fur.

Note: For allergy protection, just freeze cuddly toys for 24 hours then wash and dry them. Repeat every 6 weeks.

Before drying remove accessories such as clothes, collars or sound boxes and protect plastic eyes with masking

tape after drying them with a cloth.

The programme time will vary dependant on the exact make up of the load.

The maximum load should not exceed 2.5kg and no individual item should be greater than 600g.

Heat & Enjoy

This programme helps to heat towels & bathrobes for a warm sensation after a bath or shower. It is also useful for

warming clothes before dressing during winter. The cycle heats clothes to 37°C (Body Temperature) and runs at this

temperature for a maximum of 4 hours or until you stop the cycle by opening the door.

Maximum load 3kg.

Note: During this programme the Sensing icon on the display unit flashes.

Refresh

! ‘Refresh’ is not a drying programme and should not be used for wet articles of clothing.

●

It can be used on any load size but is more effective on smaller loads.

●

Do not overload your dryer (see Laundry).

●

This is a 20 minute programme that airs your clothes with cool air. Also use to cool warm clothes.

Programme Options available

13 Cuddly Toys

16 Refresh

15 Easy Iron

EXTRA PROGRAMMES - Programmes Table

14 Heat & Enjoy

✗

✓

✗

✓

Dryness Levels available

Delay Timer

Crease Care

Sound

Heat Level

Timed Dry

Sensor Dry

Damp Dry

Iron Dry

Hanger Dry

Cupboard Dry

Extra Dry

●

An Automatic programme

●

An Automatic programme

●

An Automatic programme

●

An Automatic programme

Start and Programmes

●

Programmes knob

! Warning, if after pressing the START/PAUSE button

the programme knob position has changed, the new

position will NOT change the programme selected.

To change a selected programme, press the

START/PAUSE button , the light flashes Amber to

indicate the programme is paused. Select the new

programme and any options required, the light will then

flash green. Press the START/PAUSE button again

and the new programme will start.

●

OPTION buttons / lights

These buttons are used to customise the selected

programme to your requirements. A programme must

have been selected on the programme knob before an

option can be selected. Not all options are available for all

programmes (see Start and Programmes). If an option is

not available and you press the button, the buzzer will

beep three times. If the option is available the option light

in the button lights to confirm the selection.

After the START/PAUSE button has been pressed only the

Crease Care or Sound options (where available) can be

changed.

Progress ( Drying, Cool Tumble) icons

These are part of the Display, they indicate the progress

of the dryer. Each icon comes on as the corresponding

phase starts.

Time Delay (Delay Timer)

The start of some programmes (see Start and

Programmes and The Display) can be delayed for up to

24 hours.

Crease Care

The pre-care option is only available if a delayed start has

been selected. It tumbles the clothes occasionally during the

delayed period to help prevent creases developing.

The post-care option occasionally tumbles the clothes after

the end of the drying and cool tumble cycles to prevent

creases developing, should you not be available to remove

the load immediately the programme is complete.

The

display will show

‘End’ Note: The Crease Care and the

Start/Pause lights flash Amber during this phase.

Selecting this option enables both the pre and post care

functions if appropriate and when selected the light in the

button is lit.

Note: If you have selected the Sound option this option is

not available.

Heat Level buttons and lights

Not all programmes allow you to change the heat level

and some programmes allow all three heat level options:

Low, Medium and High.

When the heat level options are available pressing this

button changes the heat level and the light corresponding

to the selection is lit.

The Controls

8:88

Sound

If selected, gives a signal at the end of the drying cycle,

to remind you that the clothes are ready to be removed.

Not available with the Heat & Enjoy programme.

Note: If you have selected the Crease Care option this

option is not available.

●

DISPLAY

The display shows either the amount of time delay

remaining or an indication of the amount of time left for a

drying programme (see The Display).

The colons between the hours and minutes in the display

flash to show that the time is counting down.

When the programme finishes its cool tumble phase the

display will show ‘End’.

●

Door Opening

Opening the door (or pressing the Start/Pause button)

during a programme will stop the dryer and have the

following effects:

Note: The Start/Pause light flashes Amber during the Post

Care phase of a programme.

●

The START/PAUSE light flashes Amber.

●

The START/PAUSE button must be pressed to

resume the programme, including a delayed

start. The progress lights will change to show the

current status and the START/PAUSE light will stop

flashing and turn green.

●

During a delay phase the delay will continue to

count down.

●

During the post-care phase of a drying programme,

the programme will finish. Pressing the

START/PAUSE button will re-start a new programme

at the beginning.

●

Changing the programmes knob will select a new

programme and the START/PAUSE light will flash

green. You can use this to select the Refresh

programme to cool the clothes, if you find them

dry enough. Press the START/PAUSE button to

begin a new programme.

●

Note

If you have a power cut, switch off the power or remove

the plug. When power is restored, press and hold the

ON/OFF button until the dryer reactivates, then press the

Start/Pause button.

Sorting your laundry

●

Check symbols on clothing labels to make sure

that the articles can be tumble dried.

●

Sort laundry by fabric type.

●

Empty pockets and check buttons.

●

Close zippers and hooks and tie loose belts and

strings.

●

Wring out each item in order to eliminate as much

excess water as possible.

! Do not load dripping wet clothes into the dryer.

Maximum load size

Do not load more than maximum capacity.

These numbers refer to dry weight:

Natural fibres: 8kg max (18lb)

Synthetic fibres: 3kg max (6.6lb)

! DO NOT overload the dryer as this could result in

reduced drying performance.

Typical weights

Note: 1kg = 1000g (1lb = 16oz)

Clothes

Blouse Cotton 150g (5oz)

Other 100g (3oz)

Dress Cotton 500g (1lb 2oz)

Other 350g (12oz)

Jeans 700g (1lb 6oz)

10 nappies 1000g (2lb 3oz)

Shirt Cotton 300g (10oz)

Other 200g (7oz)

T-Shirt 125g (4oz)

Household Items

Duvet cover Cotton 1500g (3lb 5oz)

(Double) Other 1000g (2lb 3oz)

Large Tablecloth 700g (1lb 6oz)

Small Tablecloth 250g (9oz)

Tea Towel 100g (3oz)

Bath Towel 700g (1lb 6oz)

Hand Towel 350g (12oz)

Double Sheet 500g (1lb 2oz)

Single Sheet 350g (12oz)

At the end of a drying cycle, cottons could still be

damp if you grouped cottons and synthetics together.

If this happens simply give them an additional short

period of drying.

Wash Care Labels

Look at the labels on your garments, especially when

tumble drying for the first time. The following symbols

are the most common:

May be tumble dried

Do not tumble dry

Tumble dry at high heat setting

Tumble dry at low heat setting

Items not suitable for tumble drying

●

Articles that containing rubber or rubber-like

materials or plastic film (pillows, cushions, or PVC

rainwear), any other flammable articles or objects

that contain flammable substances (towels soiled

with hair spray).

●

Glass fibres (certain types of draperies)

●

Items which have been dry cleaned

●

Items with the ITCL Code (see Special

clothing items). These can be cleaned with special

at-home dry cleaning products. Follow instructions

carefully.

●

Large bulky items (quilts, sleeping bags, pillows,

cushions, large bedspreads etc). These expand

when drying and would prevent airflow through

the dryer.

Laundry

●

Fabrics: items that are the same type of fabric but

different textures and thicknesses may not have

the same drying time.

●

Quantity of laundry: single items or small loads

may take longer to dry.

●

Dryness: If you are going to iron some of your

clothes, they can be taken out while still a bit

damp. Others can be left longer if you need them

to be completely dry.

●

Heat setting.

●

Room temperature: if the room where the dryer is

located is cold, it will take longer for the dryer to

dry your clothes.

●

Bulk: some bulky items can be tumble dried with

care. We suggest that you remove these items

several times, shake them out, and return them to

the dryer until finished.

! Do not over-dry your clothes.

All fabrics contain a little natural moisture, which

keeps them soft and fluffy.

Special clothing items

Blankets and Bedspreads: acrylic items (Acilan,

Courtelle, Orion, Dralon) must be dried with special

care on LOW heat setting. Avoid drying for a long

period of time.

Pleated or creased garments: read the manufacturer’s

drying instructions on the garment.

Starched articles: do not dry these with non-starched

items. Make sure that as much of the starch solution is

removed from the load as possible before placing it in

the dryer. Do not over-dry: the starch will become

powdery and leave your clothing limp, which defeats

the purpose of starch.

Drying times

The table below presents APPROXIMATE drying times

in minutes. Weights refer to dry garments:

Times are approximate and can vary depending

upon:

●

Amount of water retained in clothes after spin

cycle: towels and delicates retain a lot of water.

Cottons

High

Heat

Synthetics

Medium

Heat

Delicates

(eg Acrylics)

Low

Heat

Drying times 800-1000 rpm in washing machine.

Drying times on reduced spin in washing machine.

1 kg

2 kg

4 kg

3 kg

1 kg

2 kg

1 kg

2 kg

3 kg

5 kg

6 kg

7 kg

20 - 30

35 - 45

60 - 70

45 - 60

70 - 80

80 - 100

90 - 120

20 - 40

50 - 70 90 - 130

30 - 50

40 - 70

8 kg

100 - 140

Warnings and Suggestions

! The appliance has been designed and built according

to international safety standards.

These warnings are given for safety reasons and must

be followed carefully.

General safety

●

This tumble dryer is not intended for use by

persons (including children) with reduced physical,

sensory or mental capabilities, or lack of experience

and knowledge, unless they have been given

supervision or instruction concerning use of the

appliance by a person responsible for their safety.

●

This tumble dryer has been designed for home,

and not professional use.

●

Do not touch the appliance while barefoot or with

wet hands or feet.

●

Unplug the machine by pulling on the plug, not

the cord.

●

Children must not be in proximity of the dryer

when in use. After using the dryer, turn it off and

unplug it. Keep the door closed to make sure that

children do not use it as a toy.

●

Children should be supervised to ensure that they

do not play with the dryer.

●

The appliance must be installed correctly and

have proper ventilation. The air intake vents

behind the machine, the outlet vents and the vent

tube should never be obstructed (see Installation).

●

Never direct the vent tube outlet towards the air

intake at the back of the machine.

●

Never allow the tumble dryer to recycle exhaust air.

●

Never use the dryer on carpeting where the pile

height would prevent air from entering the dryer

from the base.

●

Check to see if the dryer is empty before loading it.

●

The back of the dryer could become very

hot. Never touch it while in use.

●

Do not use the dryer unless the filter is securely

in place (see Maintenance).

●

Do not overload the dryer (see Laundry) for

maximum loads.

●

Do not load items that are dripping wet.

●

Carefully check all instructions on clothing labels

(see Laundry).

●

Do not tumble dry large, very bulky items.

●

Do not tumble dry acrylic fibres at high temperatures.

●

Complete each programme with its Cool Tumble Phase.

●

Do not turn off the dryer when there are still warm

items inside.

●

Clean the filter after each use (see Maintenance).

●

Do not allow lint to collect around the dryer.

●

Never climb on top of the dryer. It could result in

damage.

●

Always follow electrical standards and requirements

(see Installation).

●

Always buy original spare parts and accessories

(see Service).

To minimise the risk of fire in your tumble dryer, the

following should be observed:

●

Tumble dry items only if they have been washed with

detergent and water, rinsed and been through the spin

cycle. It is a fire hazard to dry items that HAVE NOT

been washed with water.

●

Do not dry garments that have been treated with

chemical products.

●

Do not tumble dry items that have been spotted or

soaked with vegetable or cooking oils, this constitutes a

fire hazard. Oil-affected items can ignite spontaneously,

especially when exposed to heat sources such as a tumble

dryer. The items become warm, causing an oxidisation

reaction with the oil, Oxidisation creates heat. If the heat

cannot escape, items can become hot enough to catch

fire. Piling, stacking or storing oil-effected items can prevent

heat from escaping and so create a fire hazard.

If it is unavoidable that fabrics containing vegetable or

cooking oil or those that have been contaminated with

hair care products be placed in a tumble dryer they should

first be washed with extra detergent - this will reduce, but

not eliminate the hazard. The cool tumble phase should

be used to reduce the temperature of the items. They

should not be removed from the dryer and piled or

stacked while hot.

●

Do not tumble dry items that have previously been

cleaned in or washed in, soaked in or soiled with

petrol/gasoline, dry cleaning solvents or other flammable

or explosive substances. Highly flammable substances

commonly used in domestic environments including

cooking oil, acetone, denatured alcohol, kerosene, spot

removers, turpentine, waxes and wax removers. Ensure

these items have been washed in hot water with an extra

amount of detergent before being dried in the tumble dryer.

●

Do not tumble dry items containing foam rubber (also

known as latex foam), or similarly textured rubber like

materials. Foam rubber materials can, when heated,

produce fire by spontaneous combustion.

●

Fabric softener or similar products should not be used in

a tumble dryer to eliminate the effects of static electricity

unless the practice is specifically recommended by the

manufacturer of the fabric softener product.

●

Do not tumble dry undergarments that contain metal

reinforcements eg. bras with metal reinforcing wires.

Damage to the tumble dryer can result if the metal

reinforcements come loose during drying.

●

Do not tumble dry rubber, plastic articles such as shower

caps or babies waterproof covers, polythene or paper.

●

Do not tumble dry rubber backed articles, clothes fitted

with foam rubber pads, pillows, galoshes and rubber

coated tennis shoes.

●

Remove all objects from pockets, especially lighters

(risk of explosion).

! WARNING: Never stop the dryer before the end of the

drying cycle unless all items are quickly removed and

spread out so that the heat is dissipated.

Saving energy and respecting the

environment

●

Wring out items to eliminate excess water before

tumble drying (if you use a washing machine first,

select a high spin cycle). Doing this will save time

and energy during drying.

●

Always dry full loads - you save energy: single

items or small loads take longer to dry.

●

Clean the filter after each use to contain energy

consumption costs (see Maintenance).

Maintenance and Care

Check the drum after each cycle

Turn the drum manually in order to remove small items

(handkerchiefs) that could have been left behind.

Cleaning the drum

! Do not use abrasives, steel wool or stainless steel

cleaning agents to clean the drum.

A coloured film may start to appear on the stainless

steel drum, this may be caused by a combination of

water and, or cleaning agents such as fabric conditioner

from the wash. This coloured film will not affect the

dryer performance.

Cleaning

●

External parts in metal or plastic and rubber parts

can be cleaned with a damp cloth.

●

Periodically check the vent tube and any

permanent venting fixture to make sure that there

has been no accumulation of fluff or lint, and

remove it.

●

Remove lint that collects around the filter and the

outlet vents.

! Do not use solvents or abrasives.

! Your dryer uses special bearing components which

do not need lubrication.

! Have your dryer checked regularly by authorised

technicians to ensure electrical and mechanical safety

(see Service).

Switching off the electricity

Unplug your dryer when not using it, when cleaning it

and during all maintenance operations.

Clean the filter after each cycle

The filter is an important part of your dryer:

it accumulates lint and fluff that is formed while drying.

Small items could also become trapped in the filter.

When finished drying, therefore, clean the filter by

rinsing it under running water or with your vacuum

cleaner. Should the filter become clogged up, the airflow

inside the dryer will be seriously compromised: drying

times lengthen and you will consume more energy. It

may also damage your dryer.

The filter is found in front

of the dryer trim

(see diagram).

Removing the filter:

1. Pull the plastic grip of

the filter upwards (see

diagram).

2. Open the filter and clean the lint from

the inside.

3. Replace it correctly. Ensure the filter is fully located

flush into the tumble dryer trim.

4. Remove any lint that has built up on the inside of the

door and around the door seal.

! Do not use the dryer without replacing the filter.

Troubleshooting

One day your dryer seems not to be working. Before you call your Service Centre (see Service), go through the

following troubleshooting suggestions:

Problem:

The tumble dryer won’t start.

Drying cycle will not begin.

Its taking a long time to dry.

Programme finishes and

clothes are damper than

expected.

The option lights flash and the

display shows a fault code F

followed by one or two

numbers.

The display briefly shows

every 6 seconds.

Possible causes / Solution:

●

The plug is not plugged into the socket, or not making contact.

●

There has been a power failure.

●

The fuse has blown. Try to plug another appliance into the socket.

●

You are using an extension cord? Try to plug the dryer’s power cord

directly into the socket.

●

The door is not closed securely?

●

The PROGRAMMES knob has not been set properly (see Start and

Programmes).

●

The START/PAUSE button has not been pressed (see Start and

Programmes).

●

You have set a delayed time (see Start and Programmes).

●

The filter has not been cleaned (see Maintenance).

●

The correct programme has not been selected for the type of fabric you

are drying (see Start and Programmes).

●

The flexible vent tube is obstructed (see Installation).

●

The air intake vent is obstructed (see Installation).

●

The permanent ventilation flap on the storm cover is obstructed (see

Installation).

●

The items were too wet (see Laundry).

●

The dryer was overloaded (see Laundry).

! For safety the dryer has a maximum programme time of 4 hours. If an

automatic programme has not sensed the required final moisture in this time

the dryer will complete the programme and stop. Check the above points

and run the programme again, if the results are still damp, contact the

Service Centre (see Service).

●

If the display shows a fault:

- Turn off and remove the plug. Clean the filter (see Maintenance).

Then replace the plug, turn on and start another programme. If a

fault is then displayed: Note down the code and contact the

Service Centre (see Service).

●

The dryer is in ‘Demo’ mode. Press and hold both the On/Off and

Start/Pause buttons for 3 seconds. The display will show for

3 seconds and then the dryer will resume normal operation.

Spare Parts

This dryer is a complex machine. Repairing it yourself

or having a non-authorised person try to repair it could

cause harm to one or more persons, could damage

the machine and could invalidate the spare parts

warranty.

Call an authorised technician if you experience problems

while using the machine.

Service

Before calling the Service Centre:

●

Use the troubleshooting guide to see if you can

solve the problem yourself (see Troubleshooting).

●

If not, turn off the dryer and call the Service Centre

closest to you.

What to tell the Service Centre:

●

name, address and post code.

●

telephone number.

●

the type of problem.

●

the date of purchase.

●

the appliance model (Mod.).

●

the serial number (S/N).

This information can be found on the data label inside

the door of the machine.

Disposal of old electrical appliances

The European Directive 2002/96/EC on Waste Electrical

and Electronic Equipment (WEEE), requires that old

household electrical appliances must not be disposed

of in the normal unsorted municipal waste stream. Old

appliances must be collected separately in order to

optimise the recovery and recycling of the materials

they contain and reduce the impact on human health

and the environment.

The crossed out “wheeled bin” symbol on the

product reminds you of your obligation, that

when you dispose of the appliance it must be

separately collected.

Consumers should contact their local authority or

retailer for information concerning the correct disposal

of their old appliance.

As part of our continued commitment to helping

the environment, we reserve the right to use

quality recycled components to keep down customer

costs and minimise material wastage.

●

Disposing of the packaging material: follow local

regulations, so the packaging can be recycled.

●

To minimise risk of injury to children, remove the

door and plug - then cut off mains cable, flush

with the appliance. Dispose of these parts separately

to ensure that the appliance can no longer be

plugged into a mains socket.

Comparative Programmes

Recycling and Disposal Information

●

Programmes recommended for comparative test to EN61121

! Note: This is not a full list of programme options (see Start and Programmes).

This appliance conforms to the following EC Directives:

- 2006/95/EC (Low Voltage Equipment)

- 89/336/EEC, 92/31/EEC and 93/68/EEC (Electromagnetic Compatibility)

Programme Programme to select Load size Heat Setting Dryness Option

(EN61121)

Dry Cotton 1 Cottons 8 kg High Cupboard Dry

Iron Dry Cotton 1 Cottons 8 kg High Iron Dry

Easy-care textile 4 Synthetics 3 kg Medium Cupboard Dry

TVF 85C

SÈCHE-LINGE

Notice d’utilisation et installation

Table des Matières

Informations Importantes, 19

Installation, 20-21

Où installer votre sèche-linge

Ventilation

Connexions électriques

Caler votre sèche-linge

Avant de commencer à utiliser votre sèche-linge

Description du sèche-linge, 22

Vue de face

Vue de l’arrière

Panneau de commandes

L’affichage, 23

Démarrage et programmes, 24-28

Choisir un programme

Programmes et tableaux

Les commandes

Linge, 29-30

Trier votre linge

Étiquettes d’entretien

Vêtements spéciaux

Temps de séchage

Avertissements et Suggestions, 31

Sécurité générale

Économiser de l’énergie et respecter l’environnement

Entretien et Nettoyage, 32

Éteindre l’électricité

Nettoyer le filtre après chaque cycle

Vérifier le tambour après chaque cycle

Nettoyer le sèche-linge

Que faire en cas de panne, 33

Service Après-vente, 34

Mise au rebut

! Conservez cette notice d’utilisation et d’installation à portée de main de manière à pouvoir vous y référer si

nécessaire. Emmenez-la avec vous si vous déménagez, et, si vous vendez cet appareil ou que vous le donniez à un tiers,

faites en sorte que cette notice accompagne le sèche-linge de manière à ce que le nouveau propriétaire soit informé

des avertissements et suggestions concernant le fonctionnement de ce sèche-linge.

! Lisez attentivement ce mode d’emploi; les pages suivantes contiennent des informations importantes concernant

l’installation et des suggestions relatives au fonctionnement de cet appareil.

Ce symbole vous rappele de lire le livret d’instructions.

English, 1

Español, 35

Français, 18

Português, 52

Informations Importantes

! Vous devez IMPERATIVEMENT nettoyer le filtre à

peluches A CHAQUE cycle de séchage.

Filtre...

! Négliger de nettoyer le filtre après CHAQUE cycle de séchage nuira aux performances de séchage de votre

machine.

- Le temps de séchage sera plus long et la consommation électrique sera en conséquence plus importante.

ETAPE 1.

Ouvrez la porte du

sèche-linge.

ETAPE 2.

Sortez le filtre (à l'aide

des deux encoches

passe-doigts)

Pour que votre sèche-linge à ventilation fonctionne efficacement, vous devez suivre le programme d’entretien

courant décrit ci-dessous :

ETAPE 4.

Remontez le filtre.

- Veillez à orienter les

flèches vers vous.

ETAPE 5.

Enforce le filtre à fond.

- NE faites JAMAIS

fonctionner le sèche-linge

sans avoir remis en place

le filtre

! Vous devez IMPERATIVEMENT enlever périodiquement les accumulations de peluches autour du logement du

filtre et du tube d’évacuation, TOUS les deux ou trois mois :

- Contrôlez le tube et l’installation fixe d’évacuation de façon à vérifier qu’il n’y a pas d’accumulation de

peluches. Le cas échéant, enlevez-les.

- Enlevez les peluches qui s’accumulent autour du filtre et des orifices d’évacuation.

ETAPE 3.

Ouvrez le filtre et

débarrassez-le des

peluches qui se seraient

déposées dans le maillage.

Installation

! Assurez-vous que l’extrémité du tuyau ne soit pas

dirigée vers l’orifice d’entrée d’air à l’arrière du sèche-

linge.

! Le tuyau de ventilation ne doit pas dépasser 2,4

mètres de longueur et vous devez faire en sorte

d’éviter toute accumulation éventuelle de peluches et

d’eau en le secouant fréquemment. Assurez-vous

toujours que ce tuyau ne soit pas écrasé.

Ventilation permanente

Conjointement avec le tuyau de ventilation, nous vous

recommandons d’utiliser un Kit de Ventilation

Mur/Fenêtre, disponible dans le commerce ou chez

votre Revendeur de Pièces de Rechange le plus

proche.

Montage au mur

1. Laissez une ouverture

dans le mur à gauche

l’endroit où sera installé le

sèche-linge.

2. Faites en sorte que le

tuyau soit aussi court et

droit que possible pour

éviter que de l’humidité

condensée ne revienne

dans le sèche-linge.

3. De même, le conduit

dans le mur doit être

incliné vers le bas vers

l’extérieur.

Montage à la fenêtre

1. Avec un sèche-linge

superposé, le trou dans la

fenêtre doit idéalement

être effectué au-dessous

de l’orifice de ventilation.

2. Le tuyau doit être aussi

court que possible.

En fonction de la fréquence à laquelle vous utilisez

votre sèche-linge, il est essentiel que les zones A et B

soient vérifiées périodiquement pour retirer les

peluches ou les débris. L’adaptateur du tuyau de

ventilation doit être installé solidement, ce qui évite

ainsi que de l’air humide ne soit ré-émis dans la

pièce.

! Le sèche-linge ne doit pas être repoussé à une

distance telle que l’adaptateur du tuyau soit arraché

ou que le tube soit écrasé ou plié.

! Le tuyau doit être placé à l’écart de l’orifice d’entrée

d’air ne doit être ni entaillé, ni crasé, ni plié en forme

de ‘U’ afin d’évitér d’obstruer le tuyau et de bloquer la

condensation.

Où installer votre sèche-linge

●

Placez votre sèche-linge à une certaine distance

des cuisinières, fourneaux, radiateurs, ou plaques

de cuisson à gaz, car les flammes peuvent

endommager cet appareil.

●

Si vous installez cet appareil

sous un plan de travail, faites

en sorte de laisser un espace

de 10 mm entre le dessus

de l’appareil et tout autre

objet sur ou au-dessus de la

machine, et un espace de

15 mm entre les côtés et les

éléments d’ameublement

ou les murs latéraux. Ceci a pour objectif d’assurer

une ventilation convenable. Assurez-vous que les

orifices de ventilation situés à l’arrière ne soient pas

obstrués.

●

Faites en sorte d’installer votre sèche-linge dans un

environnement qui n’est pas humide et qui est doté

d’une bonne circulation d’air dans toute la pièce.

Le sèche linge ne fonctionnera pas efficacement

dans un espace clos ou dans un placard.

! Nous vous déconseillons d’installer votre sèche-linge

dans un placard. En revanche, le sèche-linge ne doit

en aucun cas être placé derrière une porte fermant à

clé, une porte coulissante ou une porte montée sur

des gonds du côté opposé à la porte de chargement

du sèche-linge.

Ventilation

Cet appareil sèche votre linge en aspirant de l’air frais,

propre et relativement sec, en le chauffant, et en le

distribuant ensuite parmi les vêtements qui sont brassés

doucement par la rotation du tambour. Pour une

performance optimale, l’air humide est ensuite expulsé à

travers un conduit de ventilation situé à l’arrière du

sèche-linge. Lorsque le sèche-linge est en marche, une

aération adéquate est nécessaire afin d’éviter le retour de

gaz dans la pièce, provenant de la combustion d’autres

combustibles par des appareils, y compris les feux de

cheminée.

Ventilation mobile

Un tuyau de ventilation doit toujours être installé lorsque

le sèche-linge est utilisé conjointement avec une

Ventilation Mobile. Ce tuyau doit être fixé solidement à

l’arrière du sèche-linge (voir la Description du Sèche-linge).

Si possible, il vaut toujours mieux connecter ce tuyau à une

sortie permanente située près du sèche-linge. Si une

installation permanente n’est pas possible, le sèche-linge

fonctionnera tout aussi bien en faisant passer le tuyau à

travers une fenêtre partiellement ouverte.

minimale espace 10mm

minimale

espace 15mm

Page is loading ...

Whirlpool TVF 85C 6H (EX) User guide

Brand: Whirlpool

Model: TVF 85C 6H (EX)

Category: Electric laundry dryers

Type: User guide

Download PDF

report

in other languages

français: Whirlpool TVF 85C 6H (EX) Mode d'emploi
español: Whirlpool TVF 85C 6H (EX) Guía del usuario
português: Whirlpool TVF 85C 6H (EX) Guia de usuario

Whirlpool TVF 85C 6H (EX) User guide

Whirlpool TVF 85C 6H (EX) User guide

in other languages

Related papers

Other documents