Simplicity 020236-0 User manual

Brand: Simplicity

Model: 020236-0

Category: High-pressure cleaners

Type: User manual

7.0 HORSEPOWER

2900 PSI

2.3 GPM

PRESSURE WASHER

CLEANING SYSTEM

Owner’s Manual

Model No. 580.752810

Part No. 196338GS Draft 1 (05/17/2005)

• Safety

• Assembly

• Operation

• Maintenance

• Parts

• Español

HOURS: Mon. - Fri. 8 a.m. to 5 p.m. (CT)

PRESSURE WASHER

CUSTOMER HELPLINE

1-800-222-3136

PRECAUCIÓN

Antes de utilizar el producto, lea este

manual y siga todas las Reglas de

Seguridad e Instrucciones de Uso.

CAUTION

Before using this product, read this

manual and follow all Safety Rules and

Operating Instructions.

Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.

Visit our Craftsman website: www.craftsman.com

This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all

safety messages that follow this symbol to avoid possible injury or death.

Read this manual carefully and become

familiar with your pressure washer. Know its

applications, its limitations, and any hazards

involved.

The safety alert symbol ( ) is used with a signal

word (DANGER, CAUTION, WARNING), a pictorial

and/or a safety message to alert you to hazards.

DANGER indicates a hazard which, if not avoided, will

result in death or serious injury. WARNING indicates a

hazard which, if not avoided, could result in death or

serious injury. CAUTION indicates a hazard which, if

not avoided, might result in minor or moderate injury.

CAUTION, when used without the alert symbol,

indicates a situation that could result in equipment

damage. Follow safety messages to avoid or reduce

the risk of injury or death.

Hazard Symbols and Meanings

SAFETY RULES

WARRANTY

TABLE OF CONTENTS

LIMITED WARRANTY ON CRAFTSMAN PRESSURE WASHER

For one year from the date of purchase, when this Craftsman pressure washer is maintained and operated

according to the instructions in the owner's manual, Sears will repair, free of charge, any defect in material and

workmanship.

If this washer is used for commercial purposes, this warranty applies for only 90 days from the date of

purchase. If this pressure washer is used for rental purposes, this warranty applies for only 30 days after date

of purchase.

This warranty does not cover:

• Expendable items such as spark plugs or air filters, which become worn during normal use.

• Repairs necessary because of operator abuse or negligence, including damage resulting from no water

being supplied to pump or failure to maintain the equipment according to the instructions contained in the

owner's manual.

Warranty service is available by returning the pressure washer to the nearest Sears service center or dealer in

the United States.

This warranty gives you specific legal rights and you may also have other rights, which vary from state to state.

Sears, Roebuck and Co., Dept. 817WA, Hoffman Estates, IL 60179

WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

SAFETY RULES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4

FEATURES AND CONTROLS . . . . . . . . . . . . . . . . . . . . . . 5

ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-8

OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-13

SPECIFICATIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-18

STORAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19-20

TROUBLESHOOTING. . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . 22-29

EMISSION CONTROL WARRANTY . . . . . . . . . . . . . . 30-31

ESPAÑOL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32-55

HOW TO ORDER PARTS . . . . . . . . . . . . . . . . BACK PAGE

Fire

Explosion

Toxic Fumes

Hot Surface

Moving Parts

Electrical Shock

Slippery Surface

Fall

Kickback

Flying Objects

Fluid Injection

Hazardous Chemical

The engine exhaust from this product contains

chemicals known to the State of California to cause

cancer, birth defects, or other reproductive harm.

WARNING

• Operate pressure washer ONLY outdoors.

• Keep exhaust gas from entering a confined area through

windows, doors, ventilation intakes or other openings.

• DO NOT operate pressure washer inside any building or

enclosure.

• Use a respirator or mask whenever there is a chance

that vapors may be inhaled.

• Read all instructions packed with mask so you are certain

mask will provide necessary protection against inhaling

harmful vapors.

Running engine gives off carbon monoxide,

an odorless, colorless, poison gas.

Breathing carbon monoxide will cause

nausea, fainting or death.

Some chemicals or detergents may be

harmful if inhaled or ingested, causing

severe nausea, fainting or poisoning.

WARNING

• Keep spray nozzle between 8 to 24 inches away from

cleaning surface.

• Operate this unit on a stable surface.

• Cleaning area should have adequate slopes and

drainage to reduce possibility of falls due to slippery

surfaces.

• Be extremely careful if you must use pressure washer

from a ladder, scaffolding or any other relatively unstable

location.

• Firmly grasp spray gun with both hands when using high

pressure spray to avoid injury if gun kicks back.

Use of pressure washer can create puddles

and slippery surfaces.

High pressure spray could cause you to fall

if you are too close to the cleaning surface.

WARNING

WHEN ADDING OR DRAINING FUEL

• Turn pressure washer OFF and let it cool at least 2

minutes before removing fuel cap. Loosen cap slowly to

relieve pressure in tank.

• Fill or drain fuel tank outdoors.

• DO NOT overfill tank. Allow space for fuel expansion.

• Keep fuel away from sparks, open flames, pilot lights,

heat, and other ignition sources.

• DO NOT light a cigarette or smoke.

WHEN STARTING EQUIPMENT

• Ensure spark plug, muffler, fuel cap and air cleaner are

in place.

• DO NOT crank engine with spark plug removed.

• If fuel spills, wait until it evaporates before starting

engine.

WHEN OPERATING EQUIPMENT

• Do not tip engine or equipment at angle which causes

fuel to spill.

• DO NOT spray flammable liquids.

WHEN TRANSPORTING OR REPAIRING EQUIPMENT

• Transport/repair with fuel tank EMPTY or with fuel shutoff

valve OFF.

• Disconnect spark plug wire.

WHEN STORING FUEL OR EQUIPMENT WITH FUEL IN

TANK

• Store away from furnaces, stoves, water heaters, clothes

dryers or other appliances that have pilot light or other

ignition source because they can ignite fuel vapors.

Fuel and its vapors are extremely flammable

and explosive.

Fire or explosion can cause severe burns or

death.

WARNING

• When starting engine, pull cord slowly until resistance is

felt and then pull rapidly to avoid kickback.

• If engine starts and fails to continue to run or if increased

resistance is felt during starting pull attempts, squeeze

trigger on spray gun.

Rapid retraction of starter cord (kickback)

will pull hand and arm toward engine faster

than you can let go.

Broken bones, fractures, bruises or sprains

could result.

WARNING

• Fresh Start™ fuel cap is designed to hold a cartridge

which contains fuel stabilizer.

• If SWALLOWED, call physician immediately. DO NOT

induce vomiting. If inhaled, remove to fresh air. In case

of eye or skin contact, flush with water for 15 minutes.

• Store unopened cartridges in a cool, dry, well ventilated

area. Keep open cartridge in fuel cap, and fuel cap

closed on fuel tank when not in use.

• In the case of an emergency, contact a physician

immediately and call 1-800-424-9300 for material safety

information.

**Fuel stabilizer contains: 2,6-di-tret-butylphenol (128-39-2) and aliphatic

petroleum distillate (64742-47-8).

Contents are HARMFUL OR FATAL IF

SWALLOWED. Avoid contact to eyes, skin

or clothing. DO NOT take internally. Avoid

breathing the mist or vapor. Overexposure

to eyes or skin can cause irritation. Keep

stabilizer out of the reach of children.

Fuel stabilizer is a hazardous chemical.**

DANGER

• If you have questions about intended use, ask dealer or

contact Sears.

• NEVER operate units with broken or missing parts, or

without protective housing or covers.

• DO NOT by–pass any safety device on this machine.

• Before starting pressure washer in cold weather, check

all parts of the equipment to be sure ice has not formed

there.

• NEVER move machine by pulling on high pressure hose.

Use handle provided on unit.

• Check fuel system for leaks or signs of deterioration,

such as chafed or spongy hose, loose or missing

clamps, or damaged tank or cap. Correct all defects

before operating pressure washer.

• This equipment is designed to be used with Sears

authorized parts ONLY. If equipment is used with parts

that DO NOT comply with minimum specifications, user

assumes all risks and liabilities.

Improper treatment of pressure washer can

damage it and shorten its life.

CAUTION

• DO NOT secure spray gun in open position.

• DO NOT leave spray gun unattended while machine is

running.

• NEVER use a spray gun which does not have a trigger

lock or trigger guard in place and in working order.

• Always be certain spray gun, nozzles and accessories

are correctly attached.

A pressure washer produces a high pressure spray

which increases risk of injury and damage to unit.

CAUTION

• DO NOT tamper with governed speed.

• DO NOT operate pressure washer above rated pressure.

Excessively high or low operating speeds increase

risk of injury and damage to pressure washer.

CAUTION

• DO NOT wear loose clothing, jewelry or anything that

may be caught in starter or other rotating parts.

• Tie up long hair and remove jewelry.

Starter and other rotating parts can entangle

hands, hair, clothing, or accessories.

WARNING

• Always wear eye protection when using equipment or when

in vicinity of equipment in use.

High pressure spray can cause paint chips

or other particles to become airborne.

WARNING

WHEN ADJUSTING OR MAKING REPAIRS TO YOUR

PRESSURE WASHER

• Disconnect the spark plug wire from the spark plug and

place the wire where it cannot contact spark plug.

WHEN TESTING FOR ENGINE SPARK

• Use approved spark plug tester.

• DO NOT check for spark with spark plug removed.

Unintentional sparking can result in fire or

electric shock.

WARNING

• DO NOT touch hot surfaces.

• Allow equipment to cool before touching.

• The pressure washer must be at least 5 feet from

structures having combustible walls and/or other

combustible materials.

• Keep at least 3 feet of clearance on all sides of pressure

washer for adequate cooling, maintenance and servicing.

• In the State of California a spark arrester is required by law

(Section 4442 of the California Public Resources Code).

Other states may have similar laws. Federal laws apply on

federal lands. If you equip the muffler with a spark arrester,

it must be maintained in effective working order.

Running engines produce heat.

Temperature of muffler and nearby areas

can reach or exceed 150°F (65°C).

Severe burns can occur on contact.

Combustible debris, such as leaves, grass,

brush, ect. can catch fire.

WARNING

• DO NOT point spray gun at glass when using MAX (pin

point) nozzle.

• NEVER aim spray gun at plants.

High pressure spray may damage fragile items

including glass.

CAUTION

• NEVER aim spray gun at people, animals or plants.

• DO NOT allow CHILDREN to operate pressure washer.

• NEVER repair high pressure hose. Replace it.

• Keep high pressure hose connected to pump and spray

gun while system is pressurized.

• Squeeze trigger on spray gun to relieve trapped

pressure, every time you stop engine. Engage trigger

lock on spray gun.

The high pressure stream of water that this

equipment produces can pierce skin and its

underlying tissues, leading to serious injury

and possible amputation.

Spray gun retains high pressure when

pressure washer is shut down, which can

cause injury.

WARNING

• Keep water spray away from electric wiring or fatal

electric shock may result.

Spray contact with electrical wiring can

result in electrocution.

WARNING

KNOW YOUR PRESSURE WASHER

Read this owner’s manual and safety rules before operating your cleaning system.

Compare the illustrations with your cleaning system to familiarize yourself with the locations of various controls

and adjustments. Save this manual for future reference.

Chemical Reservoirs

Spray Gun

Nozzle Extension with

Quick Connect

Choke Lever

Air Filter

Fuel Tank

Pump equipped with

Automatic Cool Down System

Water Inlet

Oil Fill Cap/Dipstick

ProjectPro™ Nozzles

High Pressure Outlet

Air Filter — Protects engine by filtering dust and debris

out of intake air.

Automatic Cool Down System — Cycles water through

pump when water reaches 125°-155°F. Warm water will

discharge from pump onto ground. This system prevents

internal pump damage.

Chemical Reservoirs – Used to provide detergent or

other chemicals to the low pressure water stream.

Choke Lever — Prepares a cold engine for starting.

Dial-A-Cleaner™ Selector Knob (not shown) –

Selects any one of three chemicals or the clean water

system rinse.

Fuel Tank — Fill tank with regular unleaded fuel. Always

leave room for fuel expansion.

High Pressure Hose — Connect one end to the water

pump and the other end to the spray gun.

High Pressure Outlet — To connect high pressure hose.

Hose Reel — Used for storing hose while unit is not in

use. Hose must be detached from pump and spray

gun before storage.

Nozzle Extension with Quick Connect — Allows you to

switch between four different spray nozzles.

Oil Fill Cap/Dipstick — Check and fill engine with oil

here.

See page 7 for oil recommendations and filling

instructions.

ProjectPro™ Nozzles — Detergent, Max, General,

and Delicate Nozzle: for various cleaning applications.

Pump — Develops high pressure.

Recoil Starter — Use for starting the engine manually.

Spray Gun — Controls the application of water onto

cleaning surface with trigger device. Includes trigger lock.

Throttle Lever—Sets engine in starting mode for

recoil starter and stops a running engine.

Water Inlet — Connect garden hose here.

Hose Reel

High Pressure Hose

Recoil Starter

Throttle Lever

FEATURES AND CONTROLS

Your cleaning system requires some assembly and is

ready for use only after it has been properly serviced

with the recommended oil and fuel.

If you have any problems with the assembly of

your pressure washer, please call the pressure

washer helpline at 1-800-222-3136.

IMPORTANT: Any attempt to run the engine before it

has been serviced with the recommended oil will result

in an engine failure.

REMOVE PRESSURE WASHER

FROM CARTON

1. Slice two corners at the end of carton from top to

bottom so the panel can be folded down flat.

2. Remove hose reel box, fillers, and parts bag

shipped with cleaning system.

3. Remove spray gun, nozzle extension, and engine

oil from fillers.

4. Roll cleaning system out open end of carton.

5. Check carton for additional loose parts.

CARTON CONTENTS

Check all contents. If any parts are missing or damaged,

call the pressure washer helpline at 1-800-222-3136.

• Main Unit with Chemical Reservoir Assembly

• Handle

• Accessory Tray

• Hose Reel Components

• High Pressure Hose

• Spray Gun

• Nozzle Extension with Quick Connect Fitting and

Tip Holder

• Oil Bottle

• Parts Bag (which includes the following):

• Owner’s Manual

• Owner’s Registration Card

• Bag containing 4 multi–colored ProjectPro™

nozzles

• Fresh Start™ Fuel Cartridge

• Handle Fastening Hardware Kit (which includes):

• Carriage Bolts (2)

• Plastic Knobs (2)

• Tree Clips (4)

Become familiar with each piece before assembling the

pressure washer. Identify all contents with the illustration

on page 5. If any parts are missing or damaged, call the

pressure washer helpline at 1-800-222-3136.

ASSEMBLING CLEANING SYSTEM

Your Craftsman cleaning system will need assembly

before operation:

1. Attach handle to main unit.

2. Attach hose reel to handle as shown on page 5

according to instruction sheet included with hose reel.

3. Add oil to engine crankcase.

4. Add fuel to fuel tank.

5. Connect high pressure hose to spray gun and pump.

6. Connect water supply to pump.

7. Attach nozzle extension to spray gun.

8. Select/attach quick connect nozzle to nozzle

extension.

Attach Handle

1. Place handle assembly onto handle supports

connected to main unit. Make sure holes in handle

align with holes on handle supports.

NOTE: It may be necessary to move the handle

supports from side to side in order to align the handle

so it will slide over the handle supports.

2. Insert carriage bolts through holes from outside of

unit and attach plastic knob from inside of unit.

Tighten by hand.

3. Place accessory tray over holes on handle

(viewing from front of unit). Push tree clips into

holes until they sit flat against accessory tray.

4. Insert multi–colored ProjectPro™ nozzles and

other supplied accessories in spaces provided in

accessory tray. See “How to Use Accessory Tray”.

Attach Hose Reel

Attach hose reel to handle as shown on page 5

according to instruction sheet included with hose reel.

NOTE: There may be small tube adapters included

with the hose reel kit that is not used on this model.

IMPORTANT: You must take the hose off the reel

when operating your pressure washer. The reel is for

hose storage purposes only.

ASSEMBLY

Align Holes

Handle

Supports

Add Engine Oil

IMPORTANT: Any attempt to crank or start the engine

before it has been properly serviced with the

recommended oil will result in an engine failure.

NOTE: When adding oil to the engine crankcase, use

only high quality detergent oil rated with API service

classification SF, SG, SH, SJ or higher. DO NOT use

special additives.

1. Choose a viscosity according to table below.

* The use of multi-viscosity oils (5W-30, 10W-30, etc.)

in temperatures above 40°F (4°C) will result in higher

than normal oil consumption. When using a multi-

viscosity oil, check oil more frequently.

** If using SAE 30 oil in temperatures below 40°F

(4°C), it will result in hard starting and possible

engine bore damage due to inadequate lubrication.

2. Place pressure washer on a level surface and

clean area around oil fill.

3. Remove oil dipstick and wipe dipstick with clean

cloth. Replace and tighten dipstick. Remove and

and check oil level.

4. Slowly pour oil into oil fill opening. Pause to permit

oil to settle. Fill to “Full” mark on dipstick. DO NOT

OVERFILL. Remove dipstick and check oil level.

NOTE: You may not need to use all the supplied oil.

5. Replace and tighten dipstick.

NOTE: Check oil often during engine break–in.

Add Fuel

NOTE: This gasoline engine is certified to operate on

gasoline. Exhaust Emission Control System: EM

(Engine Modifications).

1. Use clean, fresh, regular UNLEADED fuel with a

minimum of 85 octane with equipment. DO NOT

use fuel which contains Methanol. DO NOT mix oil

with fuel.

2. Clean area around fuel fill cap, remove cap.

3. Slowly add regular unleaded fuel to fuel tank. Be

careful not to overfill. Allow about 1.5" of tank

space for fuel expansion, as shown here.

4. Install fuel cap and wipe up any spilled fuel.

CAUTION! Alcohol-blended fuels (called gasohol,

ethanol or methanol) can attract moisture, which leads

to separation and formation of acids during storage.

Acidic gas can damage the fuel system of an engine

while in storage.

To avoid engine problems, the fuel system should be

emptied before storage of 30 days or longer. Drain the

fuel tank, start the engine and let it run until the fuel lines

and carburetor are empty. Use fresh fuel next season.

See “Storage” on pages 19-20 for additional information.

NEVER use engine or carburetor cleaner products in

the fuel tank as permanent damage may occur.

Fresh Start™ Fuel Cap

Adding fuel preserver helps keep fuel fresh and

carburetors clean for easier starting, all season long.

This new fuel cap automatically drips concentrated fuel

preserver into your fuel tank.

1.5” Air Space

Tank

Fuel

Synthetic 5W-30, 10W-30

5W-30, 10W-30

°F -20 0 20 32 40 60 80 100

°C -30 -20 -10 0 10 20 30 40

STARTING TEMPERATURE RANGE ANTICIPATED BEFORE NEXT OIL CHANGE

WHEN ADDING FUEL

• Turn pressure washer OFF and let it cool at least 2

minutes before removing fuel cap. Loosen cap slowly to

relieve pressure in tank.

• Fill or drain fuel tank outdoors.

• DO NOT overfill tank. Allow space for fuel expansion.

• Keep fuel away from sparks, open flames, pilot lights,

heat, and other ignition sources.

• DO NOT light a cigarette or smoke.

Fuel and its vapors are extremely flammable

and explosive.

Fire or explosion can cause severe burns or

death.

WARNING

• If SWALLOWED, call physician immediately.

• In case of emergency, contact a physician immediately

and call 1-800-424-9300 for material safety information.

**Fuel stabilizer contains: 2,6-di-tret-butylphenol (128-39-2) and aliphatic

petroleum distillate (64742-47-8).

Contents are HARMFUL OR FATAL IF

SWALLOWED. Avoid contact to eyes, skin

or clothing. DO NOT take internally. Avoid

breathing the mist or vapor. Overexposure

to eyes or skin can cause irritation. Keep

stabilizer out of the reach of children.

Fuel stabilizer is a hazardous chemical.**

DANGER

1. Place cartridge into fuel cap.

2. Push to “snap” cartridge into place.

3. Remove tab to expose membrane.

IMPORTANT: DO NOT remove the silver foil seal on

the opposite side.

4. Reinstall fuel cap on fuel tank.

5. Periodically check the cartridge to ensure there is

still fuel stabilizer inside. If it is empty, remove

cartridge and replace.

Connect Hose and Water Supply to Pump

IMPORTANT: To avoid pump damage, you must

assemble the nozzle extension to the spray gun and

attach all hoses before you start the engine.

1. Uncoil high pressure hose and attach one end of

hose to base of spray gun. Tighten by hand.

2. Remove and discard shipping caps from pump

inlet and outlet.

3. Attach other end of high pressure hose to high

pressure outlet on pump. Tighten by hand.

4. Before connecting garden hose to water inlet,

inspect inlet screen. Clean screen if it contains

debris or have it replaced if damaged. DO NOT

run pressure washer if inlet screen is damaged.

5. Run water through garden hose for 30 seconds to

flush it of debris. Turn off water.

IMPORTANT: DO NOT siphon standing water for the

water supply. Use ONLY cold water (less than 100°F).

6. Connect garden hose (not to exceed 50 feet in

length) to water inlet. Tighten by hand.

7. Turn ON water and squeeze trigger on spray gun

to purge pump system of air and impurities.

CHECKLIST BEFORE STARTING

ENGINE

Review the unit to ensure you have performed all of

the following:

1. Make sure handle is in place and secure.

2. Check that oil has been added to proper level in

engine crankcase.

3. Add proper fuel to fuel tank.

4. Check for proper hose connections (high pressure

and water supply) and that there are no kinks,

cuts, or damage to the high pressure hose.

5. Provide proper water supply (not to exceed

100°F).

6. Be sure to read “Safety Rules” and “Operation”

sections before using the cleaning system.

Inspect inlet

screen. DO NOT

use if damaged;

clean if dirty.

CAUTION

• Damage to equipment resulting from failure to follow this

instruction will void warranty.

There MUST be at least ten feet of unrestricted garden

hose between the pressure washer inlet and any flow

shut off device, such as a ‘Y’ shut-off connector or other

convenience-type water shut-off valve.

• Always wear eye protection when using this equipment

or in vicinity of where equipment is in use.

• Before starting the pressure washer, be sure you are

wearing adequate eye protection.

High pressure spray can cause paint chips

or other particles to become airborne.

WARNING

HOW TO USE YOUR CLEANING

SYSTEM

If you have any problems operating your pressure

washer, please call the pressure washer helpline at

1-800-222-3136.

Pressure Washer Location

Pressure Washer Clearance

The pressure washer must be at least 5 ft. (152 cm)

from structures having combustible walls and/or other

combustible materials. Leave at least 3 ft. (92 cm) all

around pressure washer including overhead, for

adequate cooling, maintenance and servicing.

Place pressure washer in a well ventilated area, which

will allow for removal of deadly exhaust gas. DO NOT

place pressure washer where exhaust gas could

accumulate and enter inside or be drawn into a

potentially occupied building. Ensure exhaust gas is

kept away from any windows, doors, ventilation

intakes or other openings that can allow exhaust gas

to collect in a confined area. Prevailing winds and air

currents should be taken into consideration when

positioning pressure washer.

To Start Your Cleaning System

To start your engine-powered cleaning system for the

first time, follow these instructions step-by-step. This

information also applies whenever you start the engine

after you have let the pressure washer sit idle for at

least a day.

1. Place pressure washer near an outside water

source capable of supplying water at a flow rate

greater than 3.7 gallons per minute and no less

than 20 PSI at pressure washer end of garden

hose.

2. Check that high pressure hose is tightly connected

to spray gun and pump. See “Assembling Your

Pressure Washer” for illustrations.

3. Make sure unit is in a level position.

4. Connect garden hose to water inlet on pressure

washer pump. Turn ON water.

5. Squeeze trigger on gun to purge pump system of

air and impurities.

6. Attach nozzle extension to spray gun. Tighten by

hand.

7. Choose ProjectPro™ nozzle you want to use, pull

back on collar of nozzle extension, insert nozzle

and release collar. Tug on nozzle to make sure it

is securely in place. See “How to Use

ProjectPro™ Nozzle System”.

8. Engage trigger lock to spray gun trigger.

OPERATION

CAUTION

• Damage to equipment will result from failure to follow

this instruction.

DO NOT run the pump without the water supply

connected and turned on.

• Operate pressure washer ONLY outdoors.

• Keep exhaust gas from entering a confined area through

windows, doors, ventilation intakes or other openings.

• DO NOT operate pressure washer inside any building or

enclosure.

Running engine gives off carbon monoxide,

an odorless, colorless, poison gas.

Breathing carbon monoxide will cause

nausea, fainting or death.

WARNING

Exhaust Port

Typical Pressure

Washer Shown

Trigger Lock

9. Move throttle lever to “Fast” position, shown here

as a rabbit.

10. Move choke lever to “Choke” position.

NOTE: For a warm engine, be sure the choke lever is

in the “Run” position.

11. Grasp handle and pull recoil starter lightly until you

feel some resistance, then pull briskly.

12. Return recoil starter slowly. DO NOT let rope

“snap back” against starter.

13. When engine starts, slowly move choke lever to

“Run” position as engine warms. If engine falters,

move choke lever to “Choke” position, then to

“Run” position.

14. If engine fires, but does not continue to run,

squeeze trigger on spray gun to relieve internal

pump pressure. Move choke lever to “Run”

position, and repeat steps 11 through 13.

IMPORTANT: If engine floods, place choke lever in

“Run” position and crank until engine starts.

NOTE: Always keep the throttle lever in the “Fast”

position when operating the pressure washer.

How to Stop Your Cleaning System

1. Let engine idle for two minutes.

2. Move throttle lever on engine to “Stop” position.

3. Squeeze trigger on spray gun to relieve

trapped pressure in hose to avoid injury.

NOTE: A small amount of water will squirt out when

pressure is released.

4. Rotate the Dial-A-Cleaner™ selector knob to

the OFF position to prevent chemical leakage.

5. Engage trigger lock on spray gun when not in use.

How to Use Accessory Tray

The unit is equipped with an accessory tray with

places to store your ProjectPro™ nozzles, spray gun

and nozzle extension.

NOTE: The extra hole in the tray is for storing a utility

brush. The extra clip in the tray is for storing a turbo

nozzle. The brush and turbo nozzle are NOT included

with your pressure washer. You can buy these items

as optional accessories.

1. Place nozzle extension through hole on accessory

tray, as shown.

2. Place spray gun through hole on accessory tray

on right side of unit.

3. Insert multi–colored ProjectPro™ nozzles in

spaces provided in accessory tray.

• When starting engine, pull cord slowly until resistance is felt

and then pull rapidly to avoid kickback.

• If engine starts and fails to continue to run or if increased

resistance is felt during starting pull attempts, squeeze

trigger on spray gun.

Rapid retraction of starter cord (kickback)

will pull hand and arm toward engine faster

than you can let go.

Broken bones, fractures, bruises or sprains

could result.

WARNING

• DO NOT touch hot surfaces.

• Allow equipment to cool before touching.

• The pressure washer must be at least 5 feet from structures

having combustible walls and/or other combustible materials.

• Keep at least 3 feet of clearance on all sides of pressure

washer for adequate cooling, maintenance and servicing.

• In the State of California a spark arrester is required by law

(Section 4442 of the California Public Resources Code). Other

states may have similar laws. Federal laws apply on federal

lands. If you equip the muffler with a spark arrester, it must be

maintained in effective working order.

Running engines produce heat.

Temperature of muffler and nearby areas

can reach or exceed 150°F (65°C).

Severe burns can occur on contact.

Combustible debris, such as leaves, grass,

brush, ect. can catch fire.

WARNING

• Keep high pressure hose connected to pump and spray

gun while system is pressurized.

• Squeeze trigger on spray gun to relieve trapped

pressure, every time you stop engine. Engage trigger

lock on spray gun.

The high pressure stream of water that this

equipment produces can pierce skin and its

underlying tissues, leading to serious injury

and possible amputation.

Spray gun retains high pressure when

pressure washer is shut down, which can

cause injury.

WARNING

Choke Lever

Throttle Lever

DO NOT stop engine by moving choke lever to “Choke”

position. Backfire, fire or engine damage could occur.

CAUTION

How to Use ProjectPro™ Nozzle System

The quick–connect on the nozzle extension allows you

to switch between four different ProjectPro™ system

nozzles. The ProjectPro™ nozzles vary the pressure

and spray pattern as shown.

Follow these instructions to change ProjectPro™

nozzles:

1. Engage trigger lock on spray gun.

2. Pull back collar on quick–connect and pull current

ProjectPro™ nozzle off. Store ProjectPro™

nozzles in holder provided on the accessory tray.

3. Select desired ProjectPro™ nozzle:

• For delicate rinse (lower pressure and higher

flow), for gentle cleaning of cars/trucks, boats,

RV’s, patio furniture, lawn equipment, etc.,

select yellow delicate ProjectPro™ nozzle.

• For general rinsing (medium pressure and

medium flow), ideal for most all purpose cleaning

such as home siding, brick patios, wood decks,

driveways and sidewalks, garage floors, etc.,

select orange general ProjectPro™ nozzle.

• For maximum rinsing (higher pressure and

lower flow), for stubborn or hard to reach

surface such as second story surfaces, paint

removal, oil stains, rust removal or other

stubborn substances (tar, gum, grease, wax,

etc.), select red max ProjectPro™ nozzle.

• To apply detergent, applies project specific

cleaners to help break down stubborn dirt and

grime on a variety of surfaces, select black

ProjectPro™ cleaning detergent nozzle.

4. Pull back on collar, insert selected ProjectPro™

nozzle and release collar. Tug on ProjectPro™

nozzle to make sure it is securely in place.

5. For most effective cleaning, keep ProjectPro™

nozzle from 8 to 24 inches away from cleaning

surface. If you get the nozzle too close, you may

damage the cleaning surface.

6. DO NOT get closer than 6 inches when cleaning tires.

Delicate

40° Yellow

2350 PSI

2.7 GPM

General

15° Orange

2800 PSI

2.5 GPM

Max

0° Red

2900 PSI

2.3 GPM

Black

Use to apply

detergent

Low

Pressure

High Pressure

• NEVER exchange ProjectPro™ nozzles without locking the

trigger lock on the trigger.

• DO NOT twist ProjectPro™ nozzles while spraying.

A pressure washer produces a high pressure spray

which increases risk of injury and damage to unit.

CAUTION

Cleaning and Applying Detergent

IMPORTANT: Use detergents designed specifically

for pressure washers. Household detergents could

damage the pump.

Up to three (3) different solutions can be carried with

the cleaning system at one time. To apply detergent

follow these steps:

1. Prepare detergent solution as required by

manufacturer. Fill chemical reservoir(s) with

prepared solution as needed. Label tanks with

provided tank labels.

2. Rotate the Dial-A-Cleaner™ selector knob to letter

corresponding to desired reservoir.

NOTE: Each chemical reservoir holds two quarts.

3. Make sure black ProjectPro™ cleaning detergent

nozzle is installed.

NOTE: Detergent cannot be applied with the high

pressure nozzles (Yellow, Orange or Red).

4. Make sure garden hose is connected to water inlet

and water supply is turned on. Check that high

pressure hose is connected to spray gun and

pump; start engine.

5. Apply detergent to a dry surface, starting at lower

portion of area to be washed and work upward,

using long, even, overlapping strokes.

6. Allow detergent to soak in between 3–5 minutes

before washing and rinsing. Reapply as needed to

prevent surface from drying. DO NOT allow

detergent to dry on (prevents streaking).

Pressure Washer Rinsing

After detergent is applied, scour the surface and rinse

it clean as follows:

1. Apply trigger lock to spray gun.

2. Remove black ProjectPro™ cleaning detergent

nozzle from nozzle extension.

3. Select and install desired ProjectPro™ nozzle, as

described in “How to Use ProjectPro™ Nozzle

System”.

4. Keep spray gun a safe distance from spray

surface.

5. Apply a high pressure spray to a small area and

then check the surface for damage. If no damage,

proceed to step 6.

6. Start at top of area to be rinsed, working down

with same overlapping strokes used for cleaning.

Rinse System After Every Use

It is imperative that the detergent dispensing system

be rinsed after each use to prevent clogging or leaks:

1. Fill System Rinse reservoir with clean water.

2. Before disconnecting water supply, start your

cleaning system.

3. Make sure black ProjectPro™ cleaning detergent

nozzle is installed.

4. Rotate the Dial-A-Cleaner™ selector knob to letter

corresponding to System Rinse tank. As clean

rinse water is drawn through the system, continue

the flow until no detergent foam is observed.

5. Rotate the Dial-A-Cleaner™ selector knob to

the OFF position when finished to prevent

chemical leakage.

CAUTION

• Starting the engine without all the hoses connected and

without the water turned ON will damage the pump.

• Damage to equipment resulting from failure to follow this

instruction will void warranty.

You must attach all hoses before you start the engine.

• Keep spray nozzle between 8 to 24 inches away from

cleaning surface.

• Operate this unit on a stable surface.

• Be extremely careful if you must use the pressure

washer from a ladder, scaffolding or any other relatively

unstable location.

• Firmly grasp spray gun with both hands when using high

pressure spray to avoid injury if gun kicks back.

High pressure spray could cause you to fall

if you are too close to the cleaning surface.

WARNING

Pour detergent into one of

the tanks labeled A, B, C.

System Rinse

Reservoir

How to Use the Hose Reel

Your cleaning system is equipped with a hose reel

designed to store the hose when unit is not in use.

See “Prepare Unit for Storage” for long term storage of

more than 30 days.

After each use:

1. Disconnect hose from spray gun and high

pressure outlet on pump.

2. Drain water from hose.

3. Slide one end of hose into hole on hose reel. Turn

hose reel with handle to coil hose onto reel.

IMPORTANT: DO NOT use your cleaning system with

the hose coiled onto the hose reel. The hose reel is for

storage purposes only.

Tips

• NEVER use garden hose inlet to siphon detergent

or wax.

• If you hold the spray nozzle too far away from the

object being cleaned, washing will not be as

effective.

• Always store the cleaning system with the Dial-A-

Cleaner™ selector knob in the OFF position.

Automatic Cool Down System

(Thermal Relief)

If you run the engine on your pressure washer for

3-5 minutes without pressing the trigger on the spray

gun, circulating water in the pump can reach

temperatures above 125°F. The system engages to

cool the pump by discharging the warm water onto

the ground.

ENGINE TECHNICAL INFORMATION

This is a single cylinder, overhead valve (OHV), air

cooled engine. It is a low emissions engine.

In the State of California, Model Series 120000

engines are certified by the California Air Resources

Board to meet emissions standards for 125 hours.

Such certification does not grant the purchaser, owner

or operator of this engine any additional warranties

with respect to the performance or operational life of

this engine. The engine is warranted solely according

to the product and emissions warranties stated

elsewhere in this manual.

Power Ratings

The power ratings for an individual engine model are

initially developed by starting with SAE (Society of

Automotive Engineers) code J1940 (Small Engine

Power & Torque Rating Procedure) (Revision 2002-

05). Given both the wide array of products on which

our engines are placed, and the variety of

environmental issues applicable to operating the

equipment, it may be that the engine you have

purchased will not develop the rated horsepower when

used in a piece of power equipment (actual “on-site”

power). This difference is due to a variety of factors

including, but not limited to, the following: differences

in altitude, temperature, barometric pressure, humidity,

fuel, engine lubrication, maximum governed engine

speed, individual engine to engine variability, design of

the particular piece of power equipment, the manner in

which the engine is operated, engine run-in to reduce

friction and clean out of combustion chambers,

adjustments to the valves and carburetor, and other

factors. The power ratings may also be adjusted

based on comparisons to other similar engines utilized

in similar applications, and will therefore not

necessarily match the values derived using the

foregoing codes.

PRODUCT SPECIFICATIONS

Pressure Washer Specifications

Max Outlet Pressure . . . . . . . . . 2,900 PSI

Max Flow Rate . . . . . . . . . . . . . 2.7 GPM

Chemical Mix. . . . . . . . . . . . . . . Use as directed

Water Supply Temperature. . . . Not to exceed 100°F

Shipping Weight . . . . . . . . . . . . 74 lbs.

Engine Specifications

Rated Horsepower . . . . . . . . . . . . 7 at 3600 rpm

Bore . . . . . . . . . . . . . . . . . . . . . . . 2.69 in. (68mm)

Stroke . . . . . . . . . . . . . . . . . . . . . . 2.04 in. (52mm)

Displacement . . . . . . . . . . . . . . . . 11.58 in. (190 cc)

Spark Plug

Long Life Platinum . . . . . . . . . Champion RC12PYP

Resistor . . . . . . . . . . . . . . . . . Champion RC12YC

Set Gap To: . . . . . . . . . . . . . . . 0.020inch (0.50mm)

Armature Air Gap: . . . . . . . . . . . . 0.006-0.014 in.

(0.15-0.36mm)

Valve clearance with valve springs installed and piston 1/4 in.

(6 mm) past top dead center (check when engine is cold).

Intake . . . . . . . . . . . . . . . . . . . . . . 0.004-0.006 in.

(0.10-0.15 mm)

Exhaust . . . . . . . . . . . . . . . . . . . . 0.004-0.008 in.

(0.10-0.20 mm)

Fuel Capacity . . . . . . . . . . . . . . . . 1.6 Quarts

Oil Capacity . . . . . . . . . . . . . . . . . 22 Ounces

Oil Type:

Above 40° F . . . . . . . . . . . . . . . SAE 30

Below 40° F . . . . . . . . . . . . . . . SAE 5W-30 or 10W-30

NOTE: For practical operation, the horsepower

loading should not exceed 85% of rated horsepower.

Engine power will decrease 3-1/2% for each

1,000 feet (300 meters) above sea level and 1% for

each 10° F (5.6° C) above 77° F (25° C). It should

operate satisfactorily at an angle up to 15°.

SPECIFICATIONS

GENERAL RECOMMENDATIONS

Regular maintenance will improve the performance

and extend the life of the pressure washer. See any

authorized Sears dealer for service.

The pressure washer warranty does not cover items

that have been subjected to operator abuse or

negligence. To receive full value from the warranty,

the operator must maintain pressure washer as

instructed in this manual including proper storage as

detailed in “Storage” on pages 19-20.

Some adjustments will need to be made periodically to

properly maintain your pressure washer.

All service and adjustments should be made at least

once each season. Follow the requirements in the

“Maintenance Schedule” chart above.

NOTE: Once a year you should clean or replace the

spark plug and replace the air filter. A new spark plug

and clean air filter assure proper fuel-air mixture and

help your engine run better and last longer.

EMISSION CONTROL

Maintenance, replacement or repair of the emission

control devices and systems may be performed by any

non-road engine repair establishment or individual.

BEFORE EACH USE

1. Check engine oil level.

2. Clean debris.

3. Check water inlet screen for damage.

4. Check in-line filter for debris.

5. Check high pressure hose for leaks.

6. Check chemical tanks and filters for damage.

7. Check gun and nozzle extension assembly for

leaks.

8. Purge pump of air and contaminants.

PRESSURE WASHER MAINTENANCE

Clean Debris

Daily or before use, clean accumulated debris from

cleaning system. Keep linkage, spring and controls

clean. Keep area around and behind muffler free from

any combustible debris.

Cleaning system parts should be kept clean to reduce

the risk of overheating and ignition of accumulated

debris.

MAINTENANCE

OWNER’S RESPONSIBILITIES

Follow the hourly or calendar intervals, whichever occurs first.

More frequent service is required when operating in adverse conditions noted below.

¹ Clean if clogged. Replace if perforated or torn.

² Change oil after the first (5) operating hours and every 50 hours or yearly thereafter.

Change sooner when operating under dirty or dusty conditions.

³ Replace more often under dirty or dusty conditions.

MAINTENANCE SCHEDULE

FILL IN DATES AS YOU

COMPLETE REGULAR SERVICE

SERVICE DATES

MAINTENANCE TASK

Before

Each Use

Every 25

Hours or

Yearly

Every 50

Hours or

Yearly

Every 100

Hours or

Yearly

PRESSURE WASHER

Check/clean water inlet screen

X¹

Check high pressure hose X

Check chemical tanks and filters X

Check spray gun and assembly for leaks X

Purge pump of air and contaminants X

Change pump oil X

Prepare pump for storage below 32°F See Storage on pages 19-20.

ENGINE

Check oil level

Clean debris X

Change engine oil X²

Service air cleaner X³

Service spark plug X

Service spark arrester X

Clean cooling system X²

Prepare for storage If unit is to remain idle for longer than 30 days.

• Use a damp cloth to wipe exterior surfaces clean.

• Use a soft bristle brush to loosen caked on dirt, oil,

etc.

• Use a vacuum cleaner to pick up loose dirt and debris.

• Use low pressure air (not to exceed 25 psi) to blow

away dirt. Inspect cooling air slots and openings on

the pressure washer. These openings must be kept

clean and unobstructed.

Check and Clean Inlet Screen

Examine garden hose inlet screen. Clean if it is

clogged or replace if it is torn.

Check High Pressure Hose

High pressure hoses can develop leaks from wear,

kinking, or abuse. Inspect hose before each use.

Check for cuts, leaks, abrasions, bulging of cover, or

damage or movement of couplings. If any of these

conditions exist, replace hose immediately.

Check Chemical Reservoirs

Tank covers should snap cleanly onto tank. Ensure

chemical labels correctly identify tank contents.

Ensure that the System Rinse tank is filled with clean

water. Ensure that Dial-A-Cleaner™ selector knob

rotates freely between each position. Examine the

tanks and replace if the filter is clogged.

Check Gun and Nozzle Extension

Examine hose connection to spray gun and make sure

it is secure. Test trigger by pressing it and making

sure it springs back into place when you release it. Put

safety latch in UP position and test trigger. You should

not be able to press trigger. Replace spray gun

immediately if it fails any of these tests.

Check In-Line Filter

Refer to the illustration and service the in-line filter if it

becomes clogged, as follows:

1. Detach spray gun and nozzle extension from high

pressure hose. Detach nozzle extension from

spray gun and remove o-ring and screen from

nozzle extension. Flush screen, spray gun, and

nozzle extension with clean water to clear debris.

2. Place in-line filter screen into threaded end of nozzle

extension. Direction does not matter. Push screen in

with eraser end of pencil until it rests flat at bottom

of opening. Take care to not bend screen.

3. Place o-ring into recess. Push o-ring snugly

against in-line filter screen.

4. Assemble nozzle extension to spray gun, as

described earlier in manual.

Nozzle Maintenance

A pulsing sensation felt while squeezing the spray gun

trigger may be caused by excessive pump pressure.

The principal cause of excessive pump pressure is a

nozzle clogged or restricted with foreign materials,

such as dirt, etc. To correct the problem, immediately

clean the nozzle following these instructions:

1. Shut off engine and turn off water supply.

2. Remove nozzle from end of nozzle extension.

3. Remove in-line filter from other end of nozzle

extension.

4. Use a small paper clip to free any foreign material

clogging or restricting nozzle.

5. Using a garden hose, remove additional debris by

back flushing water through nozzle extension.

Back flush between 30 to 60 seconds.

6. Reinstall nozzle and in-line filter into nozzle

extension.

7. Reconnect nozzle extension to spray gun.

8. Reconnect water supply, turn on water, and start

engine.

9. Test pressure washer by operating with each

quick connect nozzle.

O–Ring Maintenance

Purchase an O–Ring Repair Kit at your local Sears or by

calling 1-800-366-PART or online at www.sears.com. It

is not included with the pressure washer. This kit

includes replacement o-rings, rubber washer and water

inlet filter. Refer to the instruction sheet provided in the

kit to service your unit’s o-rings.

Nozzle

Extension

In-line Filter

O-ring

• NEVER repair high pressure hose. Replace it.

• Replacement hose rating MUST exceed maximum

pressure rating of unit.

The high pressure stream of water that this

equipment produces can pierce skin and its

underlying tissues, leading to serious injury

and possible amputation.

WARNING

• DO NOT insert any objects through cooling slots.

Improper treatment of pressure washer can

damage it and shorten its life.

CAUTION

Use wire here

to remove

debris.

Pump Maintenance

Changing Pump Oil

Change oil every 50 hours or once yearly, whichever

occurs first.

NOTE: You must purchase an approved bottle of

pump oil by calling 1-800-366-PART or online at

www.sears.com.

Change pump oil as follows:

1. Drain engine oil and fuel from pressure washer.

2. Use a 8mm allen wrench to remove black pump

oil cap between high pressure outlet and garden

hose inlet.

3. Tilt pressure washer to drain oil into an approved

container until it drips slowly from pump.

4. Tilt pressure washer in opposite direction and

empty premeasured pump oil bottle into same

opening (a small funnel may be helpful).

5. Install black pump oil cap and tighten firmly.

6. Set pressure washer in upright position. Add fuel

and engine oil.

ENGINE MAINTENANCE

Checking Oil Level

Oil level should be checked prior to each use or at least

every 8 hours of operation. Keep oil level maintained.

Changing Oil

Change engine oil after the first 5 hours and every

50 hours thereafter. If you are using your pressure

washer under extremely dirty or dusty conditions, or in

extremely hot weather, change oil more often.

KEEP OUT OF REACH OF CHILDREN.

DON'T POLLUTE. CONSERVE

RESOURCES. RETURN USED OIL TO

COLLECTION CENTERS.

Change oil while engine is still warm from running,

as follows:

1. Drain fuel tank by running pressure washer until

fuel tank is empty.

2. Disconnect spark plug wire and keep it away from

spark plug.

3. Clean area around oil fill, remove oil fill

cap/dipstick. Wipe dipstick clean.

4. Tip your pressure washer to drain oil from oil fill

into a suitable container making sure you tip your

unit away from spark plug and air cleaner. When

crankcase is empty, return pressure washer to

upright position.

5. Wipe dipstick clean, insert it into oil fill hole and

tighten securely, remove dipstick. Add

recommended oil up to “Full” mark on dipstick.

Pour slowly. Wipe dipstick clean each time oil

level is checked. DO NOT overfill.

6. Install oil fill plug and dipstick, tighten securely.

7. Wipe up any remaining oil.

8. Reconnect spark plug wire to spark plug.

Service Air Cleaner

Your engine will not run properly and may be

damaged if you run it with a dirty air cleaner.

Service the air cleaner once every 25 hours of

operation or once each year, whichever comes first.

Service more often if operating under dirty or dusty

conditions. Replacements are available at your local

Sears service center.

Oil Cap

WHEN ADJUSTING OR MAKING REPAIRS TO YOUR

PRESSURE WASHER

• Disconnect the spark plug wire from the spark plug and

place the wire where it cannot contact spark plug.

WHEN TESTING FOR ENGINE SPARK

• Use approved spark plug tester.

• DO NOT check for spark with spark plug removed.

Unintentional sparking can result in fire or

electric shock.

WARNING

• Used motor oil has been shown to cause skin cancer in

certain laboratory animals.

• Thoroughly wash exposed areas with soap and water.

Avoid prolonged or repeated skin contact with used

motor oil.

CAUTION

To service the air cleaner, follow these steps:

1. Loosen two screws and lift off cover.

2. Carefully remove air cleaner from base.

3. Install clean (or new) air cleaner in base. Air

cleaner must fit securely in base.

4. Place cover over air cleaner and tighten screws.

NOTE: You can purchase new air filter elements by

calling 1-800-366-PART.

Service Spark Plug

Service the spark plug every 100 hours of operation or

yearly, whichever occurs first.

1. Clean area around spark plug.

2. Remove and inspect spark plug.

3. Replace spark plug if electrodes are worn, or if

insulator is cracked or chipped.

4. For replacement use either the standard resistor

spark plug, Champion RC12YC or the long life

platinum spark plug, Champion RC12PYP.

5. Check electrode gap with wire feeler gauge and

set gap at 0.020 inches (0.50mm), if necessary.

6. Install spark plug, tighten securely.

NOTE: You can purchase a new spark plug by calling

1-800-366-PART.

Carburetor

If you think your carburetor needs adjusting, see your

nearest Sears service center. Engine performance

may be affected at altitudes above 3000 feet. For

operation at higher elevations, contact your nearest

Sears service center.

Spark Arrester Service

Your engine is not factory-equipped with a spark

arrester. In some areas, it is illegal to operate an

engine without a spark arrester. Check local laws and

regulations. A spark arrester is available from your

nearest Sears service center. If you need to order a

spark arrester, please call 1-800-366-PART.

The spark arrester must be serviced every 50 hours to

keep it functioning as designed.

If the engine has been running, the muffler will be very

hot. Allow the muffler to cool before servicing the

spark arrester.

• Remove spark arrester screen for cleaning and

inspection.

• Replace if screen is damaged.

Air Cooling System

Over time debris may accumulate in cylinder cooling

fins and cannot be observed without partial engine

disassembly. For this reason, we recommend you

have an authorized Sears service dealer clean the

cooling system per recommended intervals (see

“Maintenance Schedule” on page 15). Equally

important is to keep top of engine free from debris.

See “Clean Debris”.

• DO NOT touch hot surfaces.

• Allow equipment to cool before touching.

• The pressure washer must be at least 5 feet from

structures having combustible walls and/or other

combustible materials.

• Keep at least 3 feet of clearance on all sides of pressure

washer for adequate cooling, maintenance and servicing.

• In the State of California a spark arrester is required by law

(Section 4442 of the California Public Resources Code).

Other states may have similar laws. Federal laws apply on

federal lands. If you equip the muffler with a spark arrester,

it must be maintained in effective working order.

Running engines produce heat.

Temperature of muffler and nearby areas

can reach or exceed 150°F (65°C).

Severe burns can occur on contact.

Combustible debris, such as leaves, grass,

brush, etc. can catch fire.

WARNING

Two Screws

Cover

Cartridge

Base

AFTER EACH USE

Water should not remain in the unit for long periods of

time. Sediments or minerals can deposit on pump

parts and “freeze” pump action. Follow these

procedures after every use:

1. Flush chemical system by selecting system rinse

tank and run pressure washer with black detergent

nozzle. Flush for one minute or until detergent is

cleared from system.

2. Shut off engine and let it cool, then remove all

hoses.

3. Disconnect spark plug wire from spark plug.

4. Empty pump of all pumped liquids by pulling recoil

handle about 6 times. This should remove most

liquid in pump.

5. Rotate the Dial-A-Cleaner™ selector knob to the

OFF position.

6. Coil high pressure hose and inspect it for damage.

Cuts in hose or fraying could result in leaks and

loss of pressure. Should any damage be found,

replace hose. DO NOT attempt to repair a

damaged hose. Replace hose with genuine

Craftsman part.

7. Disconnect hose from spray gun and high

pressure outlet on pump. Drain water from hose,

gun, and nozzle extension and wipe off hose with

a rag.

8. Slide one end of hose into hole on hose reel. Turn

hose reel with handle to coil hose onto reel.

9. Reconnect spark plug wire to spark plug.

10. Store system in a clean, dry area.

WINTER STORAGE

To protect the unit from freezing temperatures:

1. Empty all chemical reservoirs as follows:

a. Disconnect hose connected to chemical inject

fitting on pump. Place end of hose into

suitable container.

b. Move selector knob to Tank A and open that

tank’s cover. Gravity should shortly empty

tank contents into container.

c. When tank is empty, repeat step (b) for tanks

B and C, using different container for each

chemical.

d. Reconnect hose to chemical inject fitting on

pump. Add 0.5 quart of clean fresh water to

each tank and close tank’s covers.

2. Flush chemical system by selecting a tank and run

pressure washer with with black detergent nozzle.

Flush until each tank is empty, then switch

selector knob to next tank. The last tank to be

emptied must be the System Rinse tank.

3. Shut off engine and let it cool, then remove high

pressure and garden hoses. Disconnect spark

plug wire from spark plug.

4. Empty pump of all pumped liquids by pulling recoil

handle about 6 times. This should remove most

liquid in pump.

5. Use pump saver, available at Sears retail item

71-74403, to treat pump. This minimizes freeze

damage and lubricates pistons and seals.

6. If pump saver is not available, connect a 3-foot

section of garden hose to water inlet adapter.

Pour RV–antifreeze (antifreeze without alcohol)

into hose. Pull recoil handle twice. Disconnect 3-

foot hose.

STORAGE

WHEN STORING FUEL OR EQUIPMENT WITH FUEL IN

TANK

• Store away from furnaces, stoves, water heaters, clothes

dryers or other appliances that have pilot light or other

ignition source because they can ignite fuel vapors.

WHEN DRAINING FUEL

• Turn pressure washer OFF and let it cool at least 2

minutes before removing fuel cap. Loosen cap slowly to

relieve pressure in tank.

• Drain fuel tank outdoors.

• Keep fuel away from sparks, open flames, pilot lights,

heat, and other ignition sources.

• DO NOT light a cigarette or smoke.

Fuel and its vapors are extremely flammable

and explosive.

Fire or explosion can cause severe burns or

death.

WARNING

CAUTION

• Failure to do so will permanently damage your pump

and render your unit inoperable.

• Freeze damage is not covered under warranty.

You must protect your unit from freezing temperatures.

LONG TERM STORAGE

If you do not plan to use the pressure washer for more

than 30 days, you must prepare the engine and pump

for long term storage.

It is important to prevent gum deposits from forming in

essential fuel system parts such as the carburetor, fuel

filter, fuel hose or tank during storage. Also,

experience indicates that alcohol-blended fuels (called

gasohol, ethanol or methanol) can attract moisture,

which leads to separation and formation of acids

during storage. Acidic gas can damage the fuel

system of an engine while in storage.

Protect Fuel System

Fuel Additive:

If adding a fuel additive, fill the fuel tank with fresh

fuel. If only partially filled, air in the tank will promote

fuel deterioration during storage. Engine and fuel can

be stored up to 24 months with additive.

• Add fuel additive following manufacturer’s

instructions.

• Make sure you have water supply to pump inlet

connected and turned ON.

• Run the engine outdoors for several minutes to be

sure that treated fuel has replaced the untreated

fuel in the carburetor.

If fuel additive is not used, remove all fuel from tank

and run engine until it stops from lack of fuel.

Change Oil

While engine is still warm, drain oil from crankcase.

Refill with recommended grade. See “Changing Oil” on

page 17.

Oil Cylinder Bore

• Remove spark plug. Squirt about 1/2 ounce of

clean engine oil into the cylinder. Cover spark plug

hole with rag. Pull recoil handle slowly to distribute

oil. Avoid spray from spark plug hole.

• Install spark plug. DO NOT connect spark plug

wire.

Protect Pump

To protect the pump use Sears pump saver to prevent

freeze damage and lubricate pistons and seals.

NOTE: Sears pump saver, item number 71-74403, is

available as an optional accessory. It is not included with

the pressure washer.

To use the pump saver:

1. Attach hose on pump saver can to pump inlet.

2. Push in can top to dispense pump saver.

3. When pump saver fluid begins to exit pump outlet,

the pump is protected.

4. Remove pump saver from pump inlet.

OTHER

• DO NOT store fuel from one season to another.

• If possible, store your unit indoors and cover it to

give protection from dust and dirt. BE SURE TO

EMPTY THE FUEL TANK.

CAUTION

• Failure to do so will permanently damage your pump

and render your unit inoperable.

• Freeze damage is not covered under warranty.

You must protect your unit from freezing temperatures.

• Always wear eye protection when using PumpSaver.

Read and follow all cautions and warnings on the

PumpSaver can label.

CAUTION

• DO NOT place a storage cover over a hot pressure

washer.

• Let equipment cool for a sufficient time before placing

the cover on the equipment.

Storage covers can be flammable.

WARNING

Page is loading ...

Simplicity 020236-0 User manual

Brand: Simplicity

Model: 020236-0

Category: High-pressure cleaners

Type: User manual

Download PDF

report

in other languages

español: Simplicity 020236-0 Manual de usuario

Simplicity 020236-0 User manual

Simplicity 020236-0 User manual

in other languages

Related papers

Other documents