Shark Rocket HV322 User manual

Category
Fireplaces
Type
User manual
1.800.798.7398
3
IMPORTANT SAFEGUARDS
FOR HOUSEHOLD USE ONLY
READ ALL INSTRUCTIONS BEFORE USE
When using an electrical appliance, basic safety precautions should
always be observed, including the following:
WARNING
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR INJURY:
1 DO NOT use outdoors or on wet surfaces.
2 Unplug from electrical outlet when not in use and before servicing.
3 DO NOT use vacuum cleaner with a damaged cord or plug. If vacuum cleaner
is not working as it should, has been dropped, damaged, left outdoors, or
dropped into water, return it to EURO-PRO Operating LLC for examination,
repair, or adjustment.
4 DO NOT pull or carry vacuum cleaner by the cord or use the cord as a handle.
5 DO NOT unplug by pulling on cord; to unplug, grasp the plug, not the cord.
6 DO NOT handle plug or vacuum cleaner with wet hands.
7 DO NOT run the vacuum cleaner over the power cord, close a door on the
cord or pull cord around sharp corners.
8 The use of an extension cord is not recommended.
9 DO NOT leave vacuum cleaner when plugged in.
10 Keep cord away from heated surfaces.
11 Turn off all controls before plugging or unplugging the vacuum cleaner.
12 Always turn off the vacuum cleaner before connecting or disconnecting
motorized nozzle.
13 Store vacuum cleaner with the power cord secured around the two cord
holders - as shown in the STORAGE section.
14 This vacuum does NOT stand upright on its own.
GENERAL USE
15 Use only as described in this manual.
16 DO NOT put any objects into openings. DO NOT use with any opening
blocked; keep free of dust, lint, hair, and anything that may reduce airflow.
17 Keep your work area well lit.
18 Keep the vacuum cleaner moving over the carpet surface at all times to
avoid damaging the carpet fibers.
19 DO NOT place vacuum cleaner on unstable surfaces such as chairs or tables.
20 DO NOT allow young children to operate the vacuum cleaner or use as a toy.
Close attention is necessary when used near children.
21 DO NOT use without dust cup and/or filters in place.
WAND ATTACHMENTS
22 DO NOT use if airflow is restricted; if air paths, wand, or accessories become
blocked, turn the vacuum cleaner off. Remove all obstructions before you
turn on the unit again.
23 Keep the end of the wand and accessory openings away from face and body.
24 Keep cleaning tools and wand suction openings away from hair, face,
fingers, uncovered feet, or loose clothing.
25 Use only manufacturer’s recommended attachments.
DUST CUP/FILTERS/ACCESSORIES
Before turning on the vacuum:
26 Make sure all filters are thoroughly dry after routine cleaning.
27 Make sure dust cup and all filters are in place after routine
maintenance. Refer to MAINTENANCE section for filter cleaning instructions.
28 Make sure accessories are free of blockages.
29 Use only filters and accessories provided by EURO-PRO Operating LLC.
[Failure to do so will void the warranty.]
GENERAL CLEANING
30 DO NOT pick up large-sized objects.
31 DO NOT pick up hard or sharp objects such as glass, nails, screws, or coins
that could damage the vacuum cleaner.
32 DO NOT pick up smoking or burning objects such as hot coals, cigarette
butts, matches or fireplace ash. DO NOT pick up drywall dust.
33 DO NOT pick up flammable or combustible materials such as lighter fluid,
gasoline, or kerosene or use vacuum in areas where they may be present.
34 DO NOT pick up toxic solutions such as chlorine bleach, ammonia, or drain
cleaner.
35 DO NOT use in an enclosed space where vapors are present from paint,
paint thinner, moth-proofing substances, flammable dust, or other explosive
or toxic materials.
36 DO NOT vacuum up any liquids.
37 DO NOT immerse vacuum cleaner in water or other liquids.
38 DO NOT use outdoors or on wet surfaces; use only on dry surfaces.
39 Use extra care when cleaning on stairs.
SAVE THESE INSTRUCTIONS
POLARIZED PLUG
To reduce the risk of electric shock, this vacuum cleaner has a polarized plug (one blade is wider than the other). As a safety feature, this plug will fit into a polarized outlet only one
way. If the plug does not fit fully into the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. DO NOT force into outlet or try to modify to fit.
English
www.sharkrocket.com
4
Dust Cup
Release
Wand
Release
MAIN UNIT
1 Power/LO/HI Switch
2 LED Light
3 Wand Release
4 Cord Hooks (not visible)
5 On-Board Tool Clip
6 Hand Vac Storage Hook
7 Floor Nozzle Release Pedal
8 Headlights
9 Dust Cup Release
1
4
9
2
5
6
3
7
8
GETTING TO KNOW YOUR SHARK
®
ROCKET
®
ULTRA-LIGHT UPRIGHT
4
Stora
ge Hook
STEP 1 STEP 2 STEP 3
ASSEMBLY
STORAGE
1 Insert the wand into the floor nozzle connector until
you hear a “click.
2 Insert the handheld portion into the top of the wand
until you hear a “click.
3 This vacuum comes with a detachable clip to store
up to 2 accessories on board. Snap clip on to the
wand. Store one accessory on top holder and one
accessory on bottom holder.
OPTION 1 OPTION 2
1.800.798.7398
5
Recommended ways to store vacuum.
OPTION 1: Press the WAND RELEASE button on the top of
the wand to release the handheld vacuum. There is a catch
on the bottom of the handheld vacuum. Hang it from the
hook located on the bottom portion of the wand. Wrap the
cord around the two cord hooks.
OPTION 2: Use the wall mount that is included. Drill two
5/16” holes and insert plastic anchors provided into the
wall. Using a Philips head screwdriver, screw the wall
mount into the plastic anchors. There is a catch on the
bottom of the handheld vacuum. Hook it onto wall mount.
CLICK
CLICK
OR
OR
English
STEP 1 STEP 2 STEP 3
www.sharkrocket.com
6
1 Plug the unit in and pull it back. 2 Slide the POWER switch to the first position to clean
bare floor surfaces and delicate area rugs. The brush
roll will spin slowly to help with debris pick-up.
3 Slide the POWER switch to the second position to
clean carpets. The brush roll will spin faster to help
pick up debris below the surface.
1 Slip two tabs between the nozzle and the duster base and attach them to the front
fasteners. Then pull the other two tabs tightly around to the back fasteners. Ensure that
the pad is flat against the bottom surface and tightly secured.
2 Slide the POWER switch to the first position and use the Dust-Away
Hard Floor
Attachment to clean hard floor surfaces. Do not use to clean damp floors or wet/sticky
messes. Only use pads provided by Shark
®
, which are designed to work with the Dust-
Away
Hard Floor Attachment.
MICROFIBER PAD CARE
Machine or hand wash the pads separately in warm water with liquid detergent.
Do not use bleach or fabric softeners as they may damage or leave a coating that will
reduce the cleaning performance of the pads.
Tumble dry low or line dry to extend the life of the microfiber fabric.
For best results, we recommend replacing your microfiber pads every 3 to 4 months.
NOTE: This vacuum does not stand up on its own, so when taking a break, rest it against furniture, on the wall, or lay it flat on the floor.
This vacuum has a 2-speed POWER slider switch, optimized for bare floor, delicate area rug and carpet cleaning.
The floor nozzle has headlights that illuminate the floor surface. The lights turn on in either speed setting.
USING THE MOTORIZED FLOOR NOZZLE
USING THE DUST-AWAY
HARD FLOOR ATTACHMENT
Wand
Release
STEP 1 STEP 2
1.800.798.7398
7
1 Stand the vacuum upright. Step on the foot pedal and
pull the wand up to disconnect from the floor nozzle.
Attach desired cleaning accessory.
NOTE: Both power settings provide the same suction
power.
2 Press the WAND RELEASE button on the top of the
wand to disconnect it from the handheld portion.
Attach desired cleaning accessory. The LED light in
the handheld vacuum turns on automatically when
the power is on.
TIP: You can attach the handheld vacuum directly to
the floor nozzle for convenient cleaning on stairs.
Videos of helpful tips on how to use accessories can be found in the Support section on www.sharkrocket.com
This vacuum has the reach to clean above floors or in tight spaces by using the wand.
It’s also a convenient handheld vacuum when using it without the wand.
ABOVE FLOOR CLEANING
English
DO NOT SCALE DRAWING
650_motorized_5_asm
SHEET 1 OF 1
UNLESS OTHERWISE SPECIFIED:
SCALE: 1:5
WEIGHT:
REV
DWG. NO.
A
SIZE
TITLE:
NAME
DATE
COMMENTS:
Q.A.
MFG APPR.
ENG APPR.
CHECKED
DRAWN
FINISH
MATERIAL
INTERPRET GEOMETRIC
TOLERANCING PER:
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
ANGULAR: MACH
BEND
TWO PLACE DECIMAL
THREE PLACE DECIMAL
APPLICATION
USED ON
NEXT ASSY
PROPRIETARY AND CONFIDENTIAL
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
<INSERT COMPANY NAME HERE>. ANY
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
<INSERT COMPANY NAME HERE> IS
PROHIBITED.
5
4
3
2
1
CREVICE TOOLS
a - 12” Crevice Tool
Clean in between tight spaces or
reach baseboards and ceilings with
this slim crevice tool. (163FLIHV3)
b - 18” Flexible Crevice Tool
Extend and flex to an 18” length to
access corners, baseboards, tight
spaces or ceilings. The rubberized
tip prevents scratches on surfaces.
(228FFJV300)
c - Duster Crevice
Two cleaning tools in one. The
crevice tool gives you extended
cleaning reach for small spaces,
while the dusting brush cleans a
multitude of surfaces. (164FLIHV3)
a b c
DUSTING BRUSHES
d - Upholstery Tool
Perfect for grabbing pet hair
and lint from furniture and other
upholstered surfaces.
(166FLIHV3)
e - Wide Upholstery Tool
Perfect for grabbing pet hair and
lint from furniture, mattresses and
other upholstered surfaces.
(165FLIHV3)
f - Dusting Brush
Great for dusting a multitude of surfaces
such as shelves, tables, baseboards,
window/door frames, and much more.
Turn the brush head to adjust the
angle to the surface you’re cleaning.
(229FFJV300)
d e
f
Multi-Angle Dusting Brush
5-position soft dusting brush for
cleaning shelves (straight out/
downward orientation), blinds,
walls, ceiling fans and lights
(upward and downward orientation).
Adjust the angle of this brush to the
desired cleaning surface. (137FLIV300)
TruePet
Motorized Brush
The power of a full size upright in the
palm of your hand. Picks up pet hair, loose
debris, and powerfully cleans dander out
of upholstery and surfaces.
(168FLV322B)
Pet Multi Tool
Two cleaning tools in one. The stiff
bristle brush gets stuck-on debris
off a multitude of surfaces. Remove
the bristles to reveal an upholstery
tool for removing stubborn pet hair
from upholstery and more. (1126FT323)
Flexible Hose
Stretch and flex this extension hose to clean around
objects and get into hard to reach spaces. Attach the
crevice tool or another accessory depending on what
you are cleaning. (290FFJ321)
Dust-Away
Hard Floor Attachment with Washable
Microfiber Pad
Direct suction for big crumbs and debris while microfiber pad
dusts hard wood and tile floors.
(XHFGV321, P200W)
Appliance Wand
Clean under and behind hard to move appliances and furniture with this adjustable 36” tool. Flip the extension
piece over to clean the underside of appliances. (138FLIV300)
Home and Car Detail Kit
Extension wands and micro tools to clean the tightest spaces. (XCDV300).
www.sharkrocket.com
8
Select cleaning accessories are included.
LOOKING FOR MORE? To enhance your cleaning experience, additional accessories are available for purchase at www.sharkrocket.com or by calling 1.800.798.7398.
For a list of what is included with this model, refer to inside flap of box.
ACCESSORIES
Empty
Empty
Monthly
D
u
s
t
C
u
p
R
e
l
e
a
s
e
STEP 1
STEP 2
1.800.798.7398
9
To keep your vacuum’s suction power optimal, follow these instructions.
Make sure unit is off and cord unplugged.
EMPTY THE DUST CUP
1 Press the WAND RELEASE button on the top of the
wand to disconnect it from the handheld portion.
OR
Remove the dust cup from the handheld vacuum by
squeezing the two DUST CUP RELEASE buttons on
both sides of the base at the same time and pulling it
out.
2 Hold dust cup over a trash bin and press the EMPTY
button on the front of the dust cup. The bottom lid
will open, allowing the debris to fall out.
NOTE: Clean the dust screen inside the dust cup as
required.
3 Once dust cup is empty, close the bottom lid and
insert dust cup back into handheld and you will hear it
click into place.
NOTE: Empty dust cup when debris reaches the MAX
fill line.
CLEAN THE FILTERS
1 Access the Pre-Motor foam and felt filters by lifting
the latch on the top of the handheld vacuum. Remove
and hand wash them every month. Let air dry
completely before replacing. Tap loose dirt off filters
between washes as needed. Insert the felt filter first
and then place the foam filter on top of it.
2 Access the Post-Motor filter under the handle.
Remove and hand wash once a year. Let air dry
completely before replacing.
TO CHECK FOR BLOCKAGES, REMOVE AND INSPECT:
HANDHELD AND WAND
1 Remove the wand from the handheld portion and
check all dust cup intake openings.
2 Remove the floor nozzle from the wand and check the
wand for blockages.
BOTTOM OF FLOOR NOZZLE
1 Use a coin to unlock the three locks on the bottom of
the floor nozzle.
2 A portion of the base is removable to allow for better
access to the brushroll and exposure to the airway.
Shine a flashlight from the bottom to check for
possible blockage in the airway.
3 Remove any string, carpet fibers or hair that may be
wrapped around the brushroll. There is a groove along
the brush bar that allows a pair of scissors to cut
across it to loosen up the debris.
4 To re-assemble, replace base by lining it up along the
front of the nozzle. Push down to snap into place until
you hear a click. Lock the three locks.
Post-Motor filter
(1084FTV320)
Pre-Motor filters
(1080FTV320)
Foam
Felt
English
MAINTENANCE
www.sharkrocket.com
10
Vacuum is not picking up dirt. No suction or light suction Check filters to see if they need cleaning. Follow instructions for rinsing and drying the filters before re-
inserting back into the vacuum.
• Dust cup may be full; empty dust cup.
Check wand, wand connections, nozzles, and accessories for blockages; clear blockages if required.
• Remove any string, carpet fibers or hair that may be wrapped around the brushroll.
Vacuum lifts area rugs • Suction is powerful. Take care when vacuuming area rugs or rugs with delicately sewn edges.
• Turn off the unit and disengage the area rug from the brushroll and restart the unit.
Brush roll does not spin If brush roll indicator light on the floor nozzle turns red, the brush roll has stopped spinning. Immediately turn
off and unplug vacuum, disconnect the nozzle and remove blockage before reconnecting and turning vacuum
back on.
If brush roll indicator light on the floor nozzle is green, the blockage has been successfully cleared. If the light
is still red, please contact customer service at 1.800.798.7398.
Vacuum turns off on its own This vacuum cleaner is equipped with a motor protective thermostat. If for some reason your vacuum
overheats, the thermostat will automatically turn the suction motor off. Should this occur, perform the
following steps to restart the thermostat:
1. Turn the unit off.
2. Unplug the vacuum.
3. Empty the dust cup and clean filters (see page previous page)
4. Check for blockages in wand, accessories and inlet openings.
5. Allow the unit to cool for a minimum of 45 minutes.
6. Plug in the vacuum.
7. Restart the unit by turning the power on.
EURO-PRO Operating LLC warrants this product to be free from material defects and workmanship for a period of five (5) years from the date of purchase when utilized for normal household use, subject
to the following conditions, exclusions and exceptions.
The liability of EURO-PRO Operating LLC is limited solely to the cost of the repair or replacement of the unit at our option. This Limited Warranty does not cover normal wear of parts and does not apply
to any unit that has been tampered with or used for commercial purposes. This Limited Warranty does not cover damage caused by misuse, abuse, negligent handling or damage due to faulty packaging
or mishandling in transit. This Limited Warranty does not cover damage or defects caused by or resulting from damages from shipping or repairs, service or alteration to the product or any of its parts,
which have been performed by a repair person not authorized by EURO-PRO Operating LLC.
If your appliance fails to operate properly while in use under normal household conditions within the warranty period, you may return the complete appliance and accessories with proof of purchase and
date, freight prepaid. For assistance with warranty service options or customer support, please call our customer care and product specialists at 1-800-798-7398 or visit our website at www.sharkrocket.
com.
If the appliance is found by EURO-PRO Operating LLC to be defective, in EURO-PRO Operating LLC’s sole discretion, we will repair or replace it free of charge. Proof of purchase is required and a fee
of $19.95 will apply to cover the cost of return freight.*
Non-durable parts including, without limitation, filters, brushes and electrical parts which normally require replacement are specifically excluded from warranty.
This Limited Warranty is extended to the original purchaser of the unit and excludes all other legal, implied and/or conventional warranties. The responsibility of EURO-PRO Operating LLC if any, is limited
to the specific obligations expressly assumed by it under the terms of this Limited Warranty. In no event is EURO-PRO Operating LLC liable for incidental or consequential damages to anyone of any nature
whatsoever. Some states do not permit the exclusion or limitation of incidental or consequential damages, so the above may not apply to you.
This Limited Warranty gives you specific legal rights, and you may also have other rights which vary from state to state or province to province.
*IMPORTANT: Carefully pack item to avoid damage in shipping. Be sure to include proof of purchase date and to attach a tag to item before packing including your name, complete address and phone
number with a note giving purchase information, model number and what you believe is the problem with the item. We recommend you insure the package (as damage in shipping is not covered by your
warranty). Mark the outside of your package “ATTENTION CUSTOMER SERVICE”.
Euro-Pro, Shark and Rocket are registered trademarks of Euro-Pro Operating LLC.
TruePet and Dust-Away are trademarks of Euro-Pro Operating LLC.
TROUBLE-SHOOTING GUIDE
FIVE-YEAR (5) LIMITED WARRANTY
1.800.798.7398
27
For Shark | Ninja U.S. Patent information visit
http://www.europro.com/USPatents
Illustrations may differ from actual product. We are constantly striving to
improve our products, therefore the specifications contained herein are
subject to change without notice.
Pour des renseignements sur les brevets de Shark | Ninja aux É.-U., veuillez
visiter http://www.europro.com/USPatents
Les illustrations peuvent différées du produit réel. Nous essayons
constamment d’améliorer nos produits, donc les clauses contenues dans
ce document peuvent changer sans pavis.
Por información acerca de las patentes en EE.UU. de Shark | Ninja,
visita http://www.europro.com/USPatents
El dibujo puede no ser igual al producto real. Nosotros nos esforzamos
constantemente en mejorar nuestros productos, por lo tanto las
especificaciones aquí indicadas pueden cambiar sin previo aviso.
EURO-PRO Operating LLC
Newton, MA USA 02459
Ville St. Laurent, Québec Canada H4S 1A7
HV320_150804_4
© 2015 Euro-Pro Operating LLC
Printed in China
Imprimé en Chine
Impreso en China
www.sharkrocket.com
1.800.798.7398
www.sharkrocket.com
1.800.798.7398
JOIN THE
CONVERSATION
PARTICIPER À LA
CONVERSATION
ÚNASE A LA
CONVERSACIÓN
WATCH AND LEARN
MORE
REGARDER ET
APPRENDRE PLUS
OBSERVAR Y
APRENDER MÁS
WE WANT TO HEAR
FROM YOU!
NOUS VOULONS VOUS
ENTENDRE!
QUEREMOS SABER
DE USTED!
@sharkcleaning
youtube.com/shark
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28

Shark Rocket HV322 User manual

Category
Fireplaces
Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI