2. AirGuard
  3. 7330
7330

AirGuard 7330 User manual

  • Hello! I've reviewed the AIRGUARD Seed Brake installation manual. This document provides detailed instructions for installing and balancing your seed brakes, covering various models and adapters. It also provides information on tools and materials needed to complete this task. I'm ready to answer your questions regarding the installation process and features of those devices.
  • What tools are needed for installation?
    Where should I install the Seed Brakes?
    How do I balance the airflow?
Seed Brakes
Installation
Manual
All manuals and user guides at all-guides.com
1
Models:
7360 - 1½” (38mm)
OD hose
7340 - 1½” (38mm)
OD hose
7330 - 1¼” (32mm)
OD hose
7350 - 1¼” (32mm)
OD hose
Adapters:
7344 - 1¼” (32mm)
OD hose
Use with 7340/7360
7346 - 1⅛” (29mm)
OD hose
Use with 7330/7350
7375 - 1⅛” (29mm)
OD hose
Use with 7340/7360
7388 - 1⁄” (30mm)
OD hose
Use with 7340/7360
7392 - 1⁄” (36mm)
OD hose
Use with 7340/7360
7394 - 1” (25mm)
OD hose
Use with 7330/7350
1” OD Hose 1⅛” OD Hose
1¼” OD Hose 1⁄” OD Hose 1⁄” OD Hose
All manuals and user guides at all-guides.com
2
• Hose Cutter or Strong Utility Knife
• Flat Head Screw Driver or Power Drill with Nut Driver
• Silicone Applicator Gun
• All-Weather Silicone (must be rain-ready and sun/freeze proof
• Shop Towels
• 6” long piece of Air Seeder Hose
• Wind Meter
SUPPLIED PARTS:
1 Seed Brake
2 SABRE Clamps
3 Adapters (optional)
INSTALL IN 6 STEPS
REQUIRED TOOLS
Be sure to have the following tools and parts available before
you begin your initial installation.
STEP 1
Choose a location on your drill to install the Seed Brakes. There are many places for installation, at the manifolds,
or between the frame and the opener. If you install at the manifolds, note that sags in the hose or longer hose
lengths may cause plugging issues with lower air speeds. For most drills, it is recommended placing the Seed
Brakes 6-12” above the opener. Ensure that the Seed Brake will not interfere with the trip mechanism or
hit the bottom of the drill frame when the trip is engaged. If the brake has to be placed further up the
hose, for proper clearance, ensure there are no dips on the hose after the brake.
All manuals and user guides at all-guides.com
3
STEP 2
Mark the hose and use your hose cutter to cut the seed tube at the desired location on every hose.
Attach all of the Seed Brakes to every cut hose using the supplied sabre clamps. Only attach the inlet
side of the Seed Brake at this time.
STEP 3
Start the Tractor and turn on the fan. Set the air speed to your highest RPM used for seeding. This will
make it easier to balance the air flow on each Seed Brake in the following steps.
STEP 4
Choose a Seed Brake in the center of the drill or where the airflow is strongest and insert a 6” piece of hose to
the exit port. Take the wind meter and measure the wind speed exiting the Seed Brake. Record the
observed target speed as this will be used to balance all of the other Seed Brakes.
All manuals and user guides at all-guides.com
4
STEP 5
Start measuring each Seed Brake exit port using the 6” piece of hose. If the wind speed is lower,
remove some of the washers to increase the speed to match the recorded target. Small Shim equals
1 mph* , Medium Shim equals 2 mph*, and Large Shim equals 4 mph*. (*approximately)
STEP 6
Once all of the Exhaust ports have been balanced proceed with installing the hoses on all of the exit
ports of the Seed Brakes. Next tighten every exhaust port cap. It is very important to place a dab of
silicone on the threads before it is tightened to prevent the caps from vibrating o
info@airguardproducts.com | 1.604.744.0070 | airguardproducts.com
#165 2771 Progressive Way, Abbotsford BC, V2T 0A7 Canada
Congratulations! You are now ready to
seed with the added protection of the
AIRGUARD™ Seed Brake Technology
For more information or support on using AIRGUARD™ Products, visit our
support page at airguardproducts.com, or call 1-604-744-0070
Thank you for choosing AIRGUARD™.
All manuals and user guides at all-guides.com
/