Type C
Charging
Battery
Power Button
WARNING! Please only use an approved charger to charge your
W01. Improper handling of the charging port, as well as the use
of an incompatible charger, may cause damage to your device
and void the warranty.
About your W01 Setting up your W01 r
Wi-FI Network Name (SSID) / Password
You can locate the SSID and password
on the device label in the battery
compartment. Use the SSID/password to
establish your internet connection.
First, insert a compatible SIM card into your W01 . Then
instrt the battery and close the battery cover.
To turn your W01 on, press and hold the Power button.
To turn it o, press and hold the Power Button until you see
all of the LED lights go up and o.
Charging your W01 r
To charge your device, insert
the USB Type C cable into the
charging port and plug into the
charger.
The power/battery LED indicator
will start blinking which indicates
the device is charging.
Key
Power Button
Power on/o for the W01 . Quick press the power key two
times, start WPS.
Type C Charging Port
The USB charger connects here.
Battery
Insert the battery to align with the battery contacts.
Reset
To perform a reset of your device, use a unfolded paper clip to
insert to the RST pin hole, and for 3 seconds, then
release.
SIM Card
Remove the battery cover from the back of your W01 and remove
the battery. Slide open the SIM door and insert your SIM as the
image shows below. Make sure the SIM is placed properly before
sliding up to close the SIM door.
4G Hotspot
Quick Start Guide
Our Website: www.atel-usa.com
Contact us at: support@atel-usa.com
For Warranty information, please see our website under the Support tab.
© 2020 Asiatelco Technologies, Inc. All Rights Reserved PN YS0344T005
2. Select the SSID of your W01 from the available
network list.
When prompted, enter your W01 password (located
on the device label in the battery compartment).
Connecting to the Internet
1. settings of devices that you want to
connect to the W01
正面
背面
System Requirements
Your W01 is compatible with any device with Wi-Fi capability
and an Internet browser. It is compatible with all major operating
systems and the latest versions of browsers.
Device Settings
You can access your Mobile Hotspot (W01 ) Online Device
Management Portal to view and edit your settings.
1. Connect your Wi-Fi capable device (e.g. laptop) to your W01 Wi-Fi
network
Open a browser (e.g. Chrome) and enter http://192.168.0.1 in
es
You can change the Admin password from the otspot Online Portal
under SETTINGS > Device Settings. Once changed, you must use the
While erent browsers may have d erent security settings for
HTTPS, additional steps may be needed if you access the Hotspot
Online Portal using https://192.168.0.1. For example, for Microsoft
Edge browser, you will need to click "Advanced > Continue to
192.168.0.1 (unsafe)" in order to access the interface.
Managing Wi-Fi networks and Connections
From the Online Portal, you can change
your Wi-Fi Settings. For example, the maximum Wi-Fi connection
is defaulted to 15 you can set it to any value between 1 and
15. The Wi-Fi band is defaulted to 2.4 GHz and you can change it
to 5GHz.
4
rW01r
4LTE Supported Bands – 2/4/5/12/13/66/71
Reset
SIM Card
Back Cover
Reset
•To reset using the reset pin hole on W01:
Make sure your W01 is on.
Remove the battery cover from the
back of your W01 .
Insert an unfolded paper clip into
the Reset pin hole and press until
the W01 LED lights are out.
Factory reset your W01 r
You can reset your W01 to factory settings with the W01
reset pin hole or via the Online Portal
NOTE: Resetting your W01 will disconnect all devices
connected to your W01. All device settings including network
name and password will be reset back to factory defaults.
•To reset from the , lick About->Backup
and Restore->Restore to Factory Defaults.
Device Display
LED Color Action Function Description
LTE/3G
Green On Represents 5-bar signal
Blue On Represents 4-bar signal
Cyan(B+G) On Represents 3-bar signal
Purple(R+B) On Represents 2-bar signal
Yellow On Represents 1-bar signal
Red Blinking
Error, no SIM or no
internet
Connection LED Indicator
FCC ID: XYO-W01 Made in China.
www.atel-usa.com
Model: W01
SSID: W01_XXXX
P/W XXXXXXXX
Admin Login: admin
Admin Password: XXXXXX
MAC: XXXXXXXXXXXX
4FF
Nano
SIM
IMEI: XXXXXXXXXXXXXXX
4折页
折好尺寸：70x90mm, 公差：+0.5mm
材质：105克双铜,4色双面印刷,双面过哑油
Pantone 301C
1
Wildix W01PRI Admin Manual
Dell PowerSwitch S5248F-ON Owner's manual
Dell PowerSwitch S5048F-ON Owner's manual
Honeywell SU3-6560D User manual
Dell EMC VxRail P series Owner's manual
Hoshizaki CRMF60-W User manual
Excelsys C3M000000000000NA User manual
Vertiv NetSure 801 CA7 User manual
MiniMax AMX5001 Short Instruction
