SDHQ 2019+ RAM 1500 Pillar Light Mounts Installation guide

Type
Installation guide

SDHQ 2019+ RAM 1500 Pillar Light Mounts are a great way to add extra lighting to your truck. They are easy to install, with no drilling or cutting required. The mounts are made of high-quality steel and are powder-coated for durability. They can be used with any type of light, and they provide a sturdy and secure mounting point. Whether you're looking to add some extra lighting for off-roading or just want to improve your visibility at night, the SDHQ 2019+ RAM 1500 Pillar Light Mounts are a great option.

SDHQ 2019+ RAM 1500 Pillar Light Mounts are a great way to add extra lighting to your truck. They are easy to install, with no drilling or cutting required. The mounts are made of high-quality steel and are powder-coated for durability. They can be used with any type of light, and they provide a sturdy and secure mounting point. Whether you're looking to add some extra lighting for off-roading or just want to improve your visibility at night, the SDHQ 2019+ RAM 1500 Pillar Light Mounts are a great option.

Latest Revision: 09/28/2021
For questions or help with the installation, please call SDHQ Offroad @ 480-633-2929
Mon.Fri. 8:00am5:30pm and Sat. 8:00am3:30pm Arizona Time. www.sdhqoffroad.com
Page 1 of 5
Product Packing List
Product:
SDHQ-33-1206-G5
Description:
2019+ RAM 1500 A Pillar Light Mounts
(1) Driver Side Mount SDHQ-33-1206-G5-A
(1) Passenger Side Mount SDHQ-33-1206-G5-B
Inspected and Packaged By: Date:
For questions or help with the installation, please call SDHQ Offroad @ 480-633-2929
Mon.Fri. 8:00am5:30pm and Sat. 8:00am3:30pm Arizona Time. www.sdhqoffroad.com
Page 2 of 5
For questions or help with the installation, please call SDHQ Offroad @ 480-633-2929
Mon.Fri. 8:00am5:30pm and Sat. 8:00am3:30pm Arizona Time. www.sdhqoffroad.com
Page 3 of 5
INSTALLATION INSTRUCTIONS
Product:
SDHQ-33-1206-G5
Description: 2019+ Ram 1500 A-Pillar Light Mounts
Tech Notes
No drilling or cutting required.
Use a hood prop and mark the outline of hood hinges to assist in realignment during install.
NOTE: Windshield wipers CANNOT be operated with Hood open.
Approx. Install Time: 1 Hour (not including wiring)
Parts List
Hardware List
Required Tools
(1) Driver Side Mount
SDHQ-33-1206-G5-A
(1) Passenger Side Mount
SDHQ-33-1206-G5-B
N/A
13mm Socket
Ratchet
Hood Prop
Marker
For questions or help with the installation, please call SDHQ Offroad @ 480-633-2929
Mon.Fri. 8:00am5:30pm and Sat. 8:00am3:30pm Arizona Time. www.sdhqoffroad.com
Page 4 of 5
***READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING INSTALLATION! ***
Installation Instructions:
1. While not necessary, it is recommended that masking tape is
applied to the edge of the hood, windshield, and fender where you
will be working to prevent accidental paint damage.
2. Open the hood and support it with a hood prop. Mark the hood and
hinge in such a way will assist in aligning the hood later. Then,
starting on the driver’s side with the 13mm socket and ratchet,
remove the rear nut that attaches the hood to the hinge. Next,
loosen the front nut while supporting the hood to prevent it from
sliding down the hinge.
3. Locate the driver side A-Pillar light mount and slide it under the
hood from the windshield. The A-Pillar will go between the
windshield fluid line and the hood. Slide the front slot in between
the hood hinge and factory nut. Align the rear slot to the rear bolt.
Tighten enough to support the mount.
4. Align the mount all the way forward and towards the outside of
the vehicle. Use the outline of the paint on the hood and your
alignment marks to align it back into factory position. Tighten both
nuts once the hood is aligned.
5. Repeat Steps 2-4 for the passenger side A-Pillar light mount.
6. Install lights in the top slot. Position the lights as desired and wire.
Enjoy your new SDHQ A-Pillar Light Mounts!
For questions or help with the installation, please call SDHQ Offroad @ 480-633-2929
Mon.Fri. 8:00am5:30pm and Sat. 8:00am3:30pm Arizona Time. www.sdhqoffroad.com
Page 5 of 5
***Double check all hardware is installed correctly and tight***
***Re-torque ALL bolts after 100 miles***
190 S McQueen Rd
Ste 109 Gilbert, AZ 85233
Phone: 480-633-2929 | Fax: 480-633-1791
www.sdhqoffroad.com
Follow us on:
Facebook Instagram
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5

SDHQ 2019+ RAM 1500 Pillar Light Mounts Installation guide

Type
Installation guide

SDHQ 2019+ RAM 1500 Pillar Light Mounts are a great way to add extra lighting to your truck. They are easy to install, with no drilling or cutting required. The mounts are made of high-quality steel and are powder-coated for durability. They can be used with any type of light, and they provide a sturdy and secure mounting point. Whether you're looking to add some extra lighting for off-roading or just want to improve your visibility at night, the SDHQ 2019+ RAM 1500 Pillar Light Mounts are a great option.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI