LED-MS150
User Manual
Please read the instruction carefully before use
CONTENTS
1. Safety Instruction ................................................................................................... 2
2. Technical Specifications .......................................................................................... 3
3. How To Set The Unit ............................................................................................... 4
3.1 Fixture Overview .............................................................................................. 4
3.2 Gobo Wheel ..................................................................................................... 6
3.3 Main Function .................................................................................................. 6
3.4 Home Position Adjustment ............................................................................. 12
4. How to Control the Unit ....................................................................................... 13
4.1 Master/Slave Built In Preprogrammed Function ............................................. 13
4.2 Easy Controller ............................................................................................... 14
4.3 DMX Controller ............................................................................................... 14
5. DMX512 Configuration ......................................................................................... 15
6. DMX Connection .................................................................................................. 19
7. Troubleshooting ................................................................................................... 20
8. Fixture Cleaning ................................................................................................... 21
1
1. Safety Instruction
WARNING
Please keep this User Guide for future consultation. If you sell the unit to another user, be sure
that they also receive this instruction manual.
Unpack and check carefully there is no transportation damage before using the unit.
Before operating, ensure that the voltage and frequency of power supply match the power
requirements of the unit.
It’s important to ground the yellow/green conductor to earth in order to avoid electric shock.
The unit is for indoor use only. Use only in a dry location.
The unit must be installed in a location with adequate ventilation, at least 50cm from adjacent
surfaces. Be sure that no ventilation slots are blocked.
Disconnect main power before replacement or servicing.
Make sure there are no flammable materials close to the unit while operating as it is fire hazard.
Use safety cable when fixes this unit. DO NOT handle the unit by taking its head only, but always
by taking its base.
Maximum ambient temperature is Ta: 40℃. DO NOT operate it where the temperature is higher
than this.
Unit surface temperature may reach up to 85℃. DO NOT touch the housing bare-hand during its
operation. Turn off the power and allow about 15 minutes for the unit to cool down before
replacing or serving.
In the event of serious operating problem, stop using the unit immediately. Never try to repair
the unit by yourself. Repairs carried out by unskilled people can lead to damage or malfunction.
Please contact the nearest authorized technical assistance center. Always use the same type
spare parts.
DO NOT touch any wire during operation as high voltage might be causing electric shock.
Warning
To prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain or
Please read the instruction carefully which includes important
information about the installation, usage and maintenance.
2
moisture.
DO NOT open the unit within five minutes after switching off.
The housing, the lenses, or the ultraviolet filter must be replaced if they are visibly damaged.
Caution
There are no user serviceable parts inside the unit. DO NOT open the housing or attempt any
repairs yourself. In the unlikely event your unit may require service, please contact your nearest
dealer.
Installation
The unit should be mounted via its screw holes on the bracket. Always ensure that the unit is
firmly fixed to avoid vibration and slipping while operating. And make sure that the structure to
which you are attaching the unit is secure and is able to support a weight of 10 times of the unit’s
weight. Also always use a safety cable that can hold 12 times of the weight of the unit when
installing the fixture.
The equipment must be fixed by professionals. And it must be fixed at a place where is out of the
touch of people and has no one pass by or under it.
2. Technical Specifications
◇ ompact moving spot with powerful output,perfect for clubs,bars,discotheques,mobie DJs.
◇ MX Channel: 8/1 0 Ch
◇ Control modes: DMX,Master/Slave and Sound Active.
◇ Great built-in shows under master/slave triggered by music.
◇ Gobo wheel: 6 rotating gobos plus open
◇ Color wheel: 8 colors plus white
◇ 14° beam angle
◇ 0%-100% smooth dimming snd various strobe effects
Power Voltage: AC 100~240V, 50/60Hz
Power Consumption: 70W
Light Source: 1 x 32W high brightness LED
Beam Angle: 14°
3
Weight: 5.3Kgs
Dimension: 212 x 174 x 352mm
3. How To Set The Unit
3.1 Fixture Overview
1. LED:
DMX On DMX input present
MASTER On Master Mode
SLAVE On Slave Mode
SOUND Flashing Sound activation
2. Button:
MENU To select the programming functions
4
DOWN To go backward in the selected functions
UP To go forward in the selected functions
ENTER To confirm the selected functions
3. LED Display:
Used to show the various menus and the selected functions.
4. DMX IN/OUT:
For DMX512 links, use 3-pin XLR plug cable to link the unit together.
5. Only For Remote Control:
Used to connect with optional CA-8 to control the fixture for Stand by, Function and Mode
select.
6. Fuse:
Used to protect the fixture from damage of over current.
7. Mains In/Out:
Connect to supply mains power and the next unit.
5
3.2 Gobo Wheel
Rotation gobo wheel
3.3 Main Function
To select any of the given functions, press the MENU button up to when the required one is
showing on the display. Select the function by ENTER button and the display will blink. Use DOWN
and UP button to change the mode. Once the required mode has been selected, Press ENTER
button to store. Back to the main functions without any change press the MENU button or wait for
8 seconds.
Hold MENU button to quit menu mode, the unit will run the built-in program you selected.
The main functions are shown below:
DANGER!
Install/change the gobo-wheel with the device switched off only.
6
FIXTURE HOURS
MENU
SOFTWARE VERSION
LED DISPLAY OFF
LED DISPLAY ON
DISPLAY INVERSION
NORMAL
SLAVE MODE
BLACKOUT MODE
SOUND MODE
TEST
SOUND SENSE
RESET
NORMAL
PAN INVERSION
NORMAL
TILT INVERSION
TEMPERATURE
7
DMX 512 ADDRESS
To select the , press the ENTER button to show the DMX ADDRESS on the display. Use the
DOWN/UP button to adjust the address from 1 to 512. Once the address has been selected, press
the ENTER button to setup, to go back to the functions without any changes press the MENU
button again. Hold and press the MENU button for one second or wait for one minute to exit the
menu mode.
CHANNEL MODE
To select the , press the ENTER button to show the DMX CHANNEL MODE on the display.
Use the DOWN/UP button to select the 8 CH or 10 CH mode. Once the mode has been selected,
press the ENTER button to setup, to go back to the functions without any changes press the MENU
button again. Hold and press the MENU button for one second or wait for one minute to exit the
menu mode.
SHOW MODE
To select the , press the ENTER button to show the SHOW MODE on the display. Use the
DOWN/UP button to select the (Show 1), (Show 2), (Show 3) or
(Show 4) mode. Once the show mode has been selected, press the ENTER button to setup, to go
back to the functions without any changes press the MENU button again. Hold and press the
MENU button for one second or wait for one minute to exit the menu mode.
SLAVE MODE
To select the , press the ENTER button to show the SLAVE MODE on the display. Use the
DOWN/UP button to select the (normal), (2 light show) mode. Once the mode has
been selected, press the ENTER button to setup, to go back to the functions without any changes
press the MENU button again. Hold and press the MENU button for one second or wait for one
minute to exit the menu mode.
8
DIMMER MODE
To select , press the ENTER button to show DIMMER MODE on the display. Use the
DOWN/UP buttons to select the (Dimmer 1), (Dimmer2), (Dimmer 3) or
(Dimmer 4) mode. Once the show has been selected, press the ENTER button to setup. To
go back to the functions without any changes press the MENU button again. Press and hold the
MENU button for about one second or wait for 7 seconds to exit the menu mode.
DIMMER SPEED
To select , press the ENTER button to show DIMMER SPEED on the display. Use the
DOWN/UP buttons to select the (Smooth) or (Fast) mode. Once the show has
been selected, press the ENTER button to setup. To go back to the functions without any changes
press the MENU button again. Press and hold the MENU button for about one second or wait for 7
seconds to exit the menu mode.
SOUND MODE
To select the , press the ENTER button to show the SOUND MODE on the display. Use the
DOWN/UP button to select the (sound mode on) or (sound mode off). Once the
mode has been selected, press the ENTER button to setup, to go back to the functions without any
changes press the MENU button again. Hold and press the MENU button for one second or wait
for one minute to exit the menu mode.
SOUND SENSE
To select the , press the ENTER button to show the SOUND SENSE on the display. Use the
DOWN/UP button to adjust the sound sensitivity from 0 to 100. Once selected, press the ENTER
button to setup, to go back to the functions without any changes press the MENU button again.
Hold and press the MENU button for one second or wait for one minute to exit the menu mode.
9
BLACKOUT MODE
To select the , press the ENTER button to show the BALCKOUT MODE on the display. Use
the DOWN/UP button to select the (normal) or (blackout) mode. Once the mode
has been selected, press the ENTER button to setup, to go back to the functions without any
changes press the MENU button again. Hold and press the MENU button for one second or wait
for one minute to exit the menu mode.
DISPLAY
To select the , press the ENTER button to show the DISPLAY on the display. Use the
DOWN/UP button to select the (normal) or (display inversion). To go back to the
functions without any changes press the MENU button again. Hold and press the MENU button for
one second or wait for one minute to exit the menu mode:
Display normal mode for the fixture putting on the floor;
Display inversion mode for the fixture fixing under ceiling.
LED DISPLAY
To select the , press the ENTER button to show the LED DISPLAY on the display. Use the
DOWN/UP button to select the (LED display on) or (LED display off) mode. Once
the mode has been selected, press the ENTER button to setup, to go back to the functions without
any changes press the MENU button again. Hold and press the MENU button for one second or
wait for one minute to exit the menu mode.
PAN INVERSION
To select the , press the ENTER button to show the PAN INVERSIO on the display. Use the
DOWN/UP button to select the (normal) or (pan inversion) mode. Once the mode
has been selected, press the ENTER button to setup, to go back to the functions without any
changes press the MENU button again. Hold and press the MENU button for one second or wait
for one minute to exit the menu mode.
10
TILT INVERSION
To select the , press the ENTER button to show the TILT INVERSIO on the display. Use the
DOWN/UP button to select the (normal) or (tilt inversion) mode. Once the mode
has been selected, press the ENTER button to setup, to go back to the functions without any
changes press the MENU button again. Hold and press the MENU button for one second or wait
for one minute to exit the menu mode.
TEST
To select the , press the ENTER button to show the TEST on the display and the unit will run
a self-test . To go back to the functions without any changes press the MENU button again. Hold
and press the MENU button for one second or wait for one minute to exit the menu mode.
TEMPERATURE
To select the , press the ENTER button to show the TEMPERATURE on the display and the
display will show the temperature of the unit . To go back to the functions without any changes
press the MENU button again. Hold and press the MENU button for one second or wait for one
minute to exit the menu mode.
FIXTURE HOURS
To select the , press the ENTER button to show the FIXTURE HOURS on the display and the
display will show the number of working hours of the unit . To go back to the functions without
any changes press the MENU button again. Hold and press the MENU button for one second or
wait for one minute to exit the menu mode.
SOFTWARE VERSION
To select the , press the ENTER button to show the SOFTWARE VERSION on the display and
the display will show the version of software of the unit . To go back to the functions without any
11
changes press the MENU button again. Hold and press the MENU button for one second or wait
for one minute to exit the menu mode.
RESET
To select the , press the ENTER button to show the RESET on the display. Press the ENTER
button and all channels of the unit will return to their standard position.
3.4 Home Position Adjustment
— Pan home position adjustment
To select the , press the ENTER button to show the PAN OFFSET on the display. Use the
DOWN and UP button to adjust the value from -127 to 127, press the ENTER button to store.
Press the MENU button to exit.
— Tilt home position adjustment
To select the , press the ENTER button to show the TILT OFFSET on the display. Use the
DOWN and UP button to adjust the value from -127 to 127, press the ENTER button to store.
Press the MENU button to exit.
— Gobo home position adjustment
To select the , press the ENTER button to show the GOBO OFFSET on the display. Use the
DOWN and UP button to adjust the value from -127 to 127, press the ENTER button to store.
12
Press the MENU button to exit.
— Color home position adjustment
To select the , press the ENTER button to show the COLOR OFFSET on the display. Use the
DOWN and UP button to adjust the value from -127 to 127, press the ENTER button to store.
Press the MENU button to exit.
4. How to Control the Unit
There are three ways to control the unit:
1. Master/slave built-in preprogram function
2. Easy controller
3. Universal DMX controller
No need to turn the unit off when you change the DMX address, as new DMX address setting will
be affect at once. Every time you turn the unit on, it will show “ ” on the display and move
all the motors to their ‘home’ position and you may hear some noises for about 20 seconds. After
that the unit will be ready to receive DMX signal or run the built in programs.
4.1 Master/Slave Built In Preprogrammed Function
By linking the units in master/slave connection, the first unit will control the other units to give an
automatic, sound activated, synchronized light show. This function is good when you want an
instant show. You have to set the first unit in master mode and select (show 1),
(Show 2), (Show 3) or (show 4) mode. Its DMX input jack will have nothing
plugged into it, and its master LED will be constantly on and sound LED will flash to the music. The
other units will have to set in slave mode and select (normal) or (2 light show)
mode. Their DMX cables plugged into the DMX input jacks (daisy chain) and the slave LED lights
will be constantly on.
2-light show
13
In slave mode, means the unit works normally and means 2-light show. In order to
create a great light show, you can set on the second unit to get contrast movement to each
other, even if you have two units only.
4.2 Easy Controller
The easy remote control is used only in master/slave mode. By connecting to
the 1/4” microphone jack of the first unit, you will find that the remote
controller on the first unit will control all the other units in Stand by, and
Mode selection.
Stand By Blackout the unit
Function 1. Sync. Strobe
2. Async strobe
3. Sound Strobe
Show
1-4
1. Press to select color
2. Hold to select gobo
Mode Sound
(LED OFF)
Show
(LED Slow Blinking)
LED ON
4.3 DMX Controller
By using a universal DMX controller to control the units, you will need to set DMX address from 1
to 512 so that the units can receive DMX signal.
Press the MENU button up to when the is showing on the display. Pressing ENTER button
and the display will blink. Use DOWN and UP button to change the DMX512 address. Once the
address has been selected, press the ENTER button to setup, to go back to the functions without
any change press the MENU button again. Hold and press the MENU button about one second or
wait for one minute to exit the menu mode. Please refer to the following diagram to address your
DMX512 channel for the first 4 units：
14
5. DMX512 Configuration
8 Channels Mode:
CHANNEL VALUE FUNCTION
1
000-255
PAN:
0 - 540°
2
000-255
TILT:
0 - 270°
3
STROBE:
000-007
Black out
008-015
Open
016-131
Strobe, Slow to Fast
132-139
Open
140-181
Slow Open, Fast Close
182-189
Open
190-231
Fast Open, Slow Close
232-239
Open
240-247
Random Strobe
248-255
Open
4
COLOR:
000-007
white
008-014
Color1
015-021
Color2
022-028
Color3
029-035
Color4
036-042
Color5
043-049
Color6
050-056
Color7
057-063
Color8
064-127
Split color
15
128-189
Clockwise Color Scroll, Fast to Slow
190-193
Stop
194-255
Counter Clockwise Color Scroll, Slow to Fast
5
GOBO:
000-009
White
010-018
Gobo1
019-027
Gobo2
028-036
Gobo3
037-045
Gobo4
046-054
Gobo5
055-063
Gobo6
064-073
White shaking
074-082
Gobo1 shaking
083-091
Gobo2 shaking
092-100
Gobo3 shaking
101-110
Gobo4 shaking
111-119
Gobo5 shaking
120-127
Gobo6 shaking
128-189
Clockwise Gobo Scroll, Fast to Slow
190-193
Stop
194-255
Counter Clockwise Gobo Scroll, Slow to Fast
6
GOBO ROTATION:
000-009
Stop
010-119
Clockwise Rotation: fast to slow
120-134
Stop
135-245
Clockwise Rotation: slow to fast
246-255
Stop
7
000-255
DIMMER:
0-100%
8
FUNCTION:
000-069
Null
070-079
Blackout while Pan/Tilt Move
080-089
Null
090-099
Blackout when Color changes
100-109
Null
110-119
Blackout when Gobo changes
120-199
Null
200-209
Reset All
210-249
Null
16
250-255
Sound Active
10 Channels Mode:
CHANNEL VALUE FUNCTION
1
000-255
PAN:
0
°
- 540°
2
000-255
PAN FINE
3
000-255
TILT:
0 - 270°
4
000-255
TILT FINE
5
STROBE:
000-007
Black out
008-015
Open
016-131
Strobe, Slow to Fast
132-139
Open
140-181
Slow Open, Fast Close
182-189
Open
190-231
Fast Open, Slow Close
232-239
Open
240-247
Random Strobe
248-255
Open
6
COLOR:
000-007
white
008-014
Color1
015-021
Color2
022-028
Color3
029-035
Color4
036-042
Color5
043-049
Color6
050-056
Color7
057-063
Color8
064-127
Split color
128-189
Clockwise Color Scroll, Fast to Slow
190-193
Stop
194-255
Counter Clockwise Color Scroll, Slow to Fast
GOBO:
17
7
000-009
White
010-018
Gobo1
019-027
Gobo2
028-036
Gobo3
037-045
Gobo4
046-054
Gobo5
055-063
Gobo6
064-073
White shaking
074-082
Gobo1 shaking
083-091
Gobo2 shaking
092-100
Gobo3 shaking
101-110
Gobo4 shaking
111-119
Gobo5 shaking
120-127
Gobo6 shaking
128-189
Clockwise Gobo Scroll, Fast to Slow
190-193
Stop
194-255
Counter Clockwise Gobo Scroll, Slow to Fast
8
GOBO ROTATION:
000-009
Stop
010-119
Clockwise Rotation
：
fast to slow
120-134
Stop
135-245
Clockwise Rotation : slow to fast
246-255
Stop
9
000-255
DIMMER:
0-100%
10
FUNCTION:
000-069
Null
070-079
Blackout while Pan/Tilt Move
080-089
Null
090-099
Blackout when Color changes
100-109
Null
110-119
Blackout when Gobo changes
120-199
Null
200-209
Reset All
210-249
Null
250-255
Sound Active
18
6. DMX Connection
Unit 1 Unit 2 Unit 3 Unit 4
1. At last unit, the DMX cable has to be terminated with a terminator. Solder a 120 ohm 1/4W
resistor between pin 2(DMX-) and pin 3(DMX+) into a 3-pin XLR-plug and plug it in the
DMX-output of the last unit.
2. Connect the unit together in a `daisy chain` by XLR plug from the output of the unit to the
input of the next unit. The cable can not branched or split to a `Y` cable. DMX 512 is a very
high-speed signal. Inadequate or damaged cables, soldered joints or corroded connectors can
easily distort the signal and shut down the system.
3. The DMX output and input connectors are pass-through to maintain the DMX circuit, when
power is disconnected to the unit.
4. Each lighting unit needs to have an address set to receive the data sent by the controller. The
address number is between 0-511 (usually 0 & 1 are equal to 1).
5. The end of the DMX 512 system should be terminated to reduce signal errors.
19
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
ACME LED-275 D User manual
-
-
-
ACME LED-3084 RGB User manual
-
Elumen8 Stage Par 220 User manual
-
Elumen8 Stage Par 220 User manual
-
-
-
-
Other documents
-
Equinox Systems Fusion 50 User manual
-
-
-
-
-
-
Briteq STAGE PAINTER 12 Owner's manual
-
Equinox Systems EQLED008 User manual
-
Versia LED-340B User manual
-
