Training Manual
Soberlink Cellular
Table of Contents
Device Call-Outs 1
Soberlink Cellular Device Diagram 2
User Activation 3
Device Activation & Client Enrollment 7
Testing Guidelines 10
Device Screens 11
Tamper Prevention 14
Restore Device to Factory Settings 15
Device Specications 16
Cellular Device Training Manual 1
Device Call-Outs
Cellular Device Training Manual 2
Device Diagram
Camera
Blue status light/Mouthpiece port
LCD screen
Power button
Display buttons
Power/Select button
Right display button
Left display button
Cellular Device Training Manual 3
User Acvaon
Soberlink will provide temporary login information and grant Admin access for rst-time Users on the Monitoring Web
Portal. After updating the login credentials, the Admin will be able to create new Users from the Admin Tab.
If the User’s email address is not yet conrmed in the Soberlink system, they will receive an Opt-In email.
Note: The User must conrm the email address in order to receive any further communication from Soberlink.
A “Welcome to Soberlink” message and temporary login will be sent to the User’s conrmed email address.
The User will click the link within the email and use the provided temporary login information to access their account
on the Monitoring Web Portal.
Cellular Device Training Manual 4
User Acvaon
Security Questions
After the welcome screen, the User will
be prompted to select and answer three
security questions.
To complete the security questions follow
these steps:
1. Click the drop-down arrows for each
question.
2. Select the desired security question
(each question may only be selected
once).
3. Fill in a personalized answer for each question.
4. Click Continue.
Cellular Device Training Manual 5
User Acvaon
After completing the security questions, the User will create a new password.
1. Enter a new password that meets all of the displayed criteria.
2. Conrm the new password by entering it in the Conrm Password eld.
3. Click Continue.
Cellular Device Training Manual 6
User Acvaon
When creating a new password, the criteria text will change according to whether or not it has been satised.
Once the criteria has been met, all of the text will be green and have a check mark next to it.
Cellular Device Training Manual 7
1. Press the Power button on the Soberlink Device and log in to the Monitoring Web Portal.
Device Acvaon and Client Enrollment
U.S. Patent No. 8,381,573
210004BF
Device ID
Activation
Information
ID: 20000004
PIN: 7081
Checking...
93%
4. Click the “Enroll New Client” button
on the Monitoring Web Portal.
2. On the Soberlink Device, select Start with the
left display button.
3. The Device will display the Device ID and
Security PIN, and begin checking for activation
on the Monitoring Web Portal.
Note: The Device ID is also displayed on the
bottom of the Device where the micro
USB port is located.
Cellular Device Training Manual 8
Device Acvaon and Client Enrollment
Enter the appropriate Client information in Steps 1 and 2 of the enrollment process.
If the User has a Soberlink Device for the Client, click
Yes in Step 3 to enter the Device ID, Security PIN, and
payment information.
If the User does not yet have a Soberlink Device for
the Client, click No in Step 3 to Pre-Enroll the Client.
The User can activate a Device for the Client at a
later time from the Home page of the Monitoring Web
Portal.
Step 2
Step 3
Step 1
Cellular Device Training Manual 9
Device Acvaon and Client Enrollment
Step 4
Waiting for Device response
Device is ready for use
Once the Activation and Client Information have been accurately entered, the Soberlink Device will display
a “Successfully Activated” message.
On the Monitoring Web Portal the User will see a green check mark, indicating that the Device has been
successfully activated and is ready for use.
In the 4th and nal step of the Enrollment process,
the User will be asked to deliver Soberlink’s Client
Agreement to the Client.
Once the User has done this, they may check the box
conrming that they have acted in accordance with
this policy.
Then click “Done” to nish enrolling the Client.
Cellular Device Training Manual 10
Follow the prompts on the screen
,QVHUWPRXWKSLHFH
7XUQRQWKHEUHDWKDO\]HU
3UHVVWKH¶VXEPLW·EXWWRQ
%ORZZKHQSURPSWHGEOXHULQJZLOOEOLQN
)LUPVWHDG\EORZLVUHTXLUHGIRUVHFRQGV
7KHWHVWZLOOWDNHDSSUR[VHFRQGVWRVHQG
7HVW VXEMHFWV VKRXOG ZDLW PLQXWHV DIWHU HDWLQJ
GULQNLQJRUVPRNLQJEHIRUHEORZLQJLQWRWKH62%(5/,1.
%UHDWKDO\]HU )DLOXUH WR ZDLW PLQXWHV FDQ SURYLGH
LQDFFXUDWHWHVWUHVXOWVDQGGDPDJHWKHVHQVRU
&RPSOHWHPDQXDOWHUPVDQGFRQGLWLRQV
FDQEHIRXQGDWZZZVREHUOLQNQHW
Sending A Test
DO
Use the Soberlink mouthpiece
Turn on the Breathalyzer
Press the ‘submit’ button
Hold the device at eye level
Look directly into camera
Take a deep breath
Deliver a rm, steady stream of breath
DON’T
Wear sunglasses or hats
Place ngers on the mouthpiece
Obstruct the camera in any way
Block the rear air vent
Use device in extreme temperatures
(Operating temp is 32-122˚F)
Tesng Guidelines
Cellular Device Training Manual 11
Device Screens
Menu Options
To access or exit the Menu,
click both display buttons at
the same time.
The power button will act as
the selection button.
Test Details
The test details may include
BrAC results and error details if
applicable.
Test History.
All testing attempts will
be recorded here in UTC
(Universal) time.
Use the display buttons to
scroll through the tests and the
power button to select a test.
HOME BACK
Test Details
Date:
Time:
BrAC:
Status:
Cell:
GPS:
11/09/2013
10:20PM
0.000
SENT
2,3,2706,-59
NEW
Test History
11/09
11/09
11/08
11/07
11/07
10:20PM
09:52AM
06:04PM
10:11PM
09:59AM
PEND
PEND
SENT
SENT
SENT
PREV NEXT
PREV NEXT
Menu Options
Test history
Air blank test
Cell coverage
Reset Device
Air Blank Test
Use this feature to make sure
the Device’s fuel cell isn’t
damaged.
The Device should test blank
air at 0.000.
Cellular Coverage
The strength of the Device’s
cellular signal is displayed on
this screen.
Reset Device
To avoid accidental reset, a
certain button combination
must be keyed after selecting
this option –
Power, left, right, power.
Air Blank Test
Device 10000001
Date: --/--/--
Time: --:--
Result: 0.000
HOME BACK
Cellular Coverage
PREV NEXT
Menu Options
Test history
Air blank test
Check for updates
Reset Device
CANCEL
to select
to select
to select
Cellular Device Training Manual 12
Device Screens
Device Info Screen
From the home screen, hold
down the left display button.
While holding, click the right
button once and continue
holding the left until the screen
appears.
Term explanation below.
DEVID:
FVER:
FWIM:
BATT:
CHG:
MODE:
CMSN:
MDATE:
CDATE:
CALR:
BLOWS:
PIN:
REG:
MEID:
MPN:
TZ:
GPS:
20000004
0.60, 1.00
CONF
4.337V 85%
CHARGING
FIELD
00000000000
2012-296-2
2012-297
149650
123, 124
7081
TRUE
A1.9D407A7
9453758263
-8
NEW FIX
Error Screen
The Device screen will
display an error code to
help with troubleshooting.
Compliant Test
A test sent with a compliant
BrAC will prompt the Device
to display this message.
The Client will need to press
“OK” after seeing the result.
Non-Compliant Test
If a non-compliant BrAC test
(.02 or higher) is submitted,
the Client will be prompted
to retest.
Note: The Client must be
enrolled in retesting on the
Schedule page of the web
portal.
Retest Required
Wait 15 minutes
Send an additional
test in 15 minutes
Time: 3:09PM PDT
OK
HOME CLOSE
Compliant Test
Has Been Sent
Time: 3:09PM
HOME CLOSE
Test Has Not
Been Sent
Cannot send test.
Please try again.
(15000)
Retest Required
Wait 15 minutes
Additional test
required at
3:24PM PDT
OK
Non-Compliant Retest
After clicking “OK” on the
previous retest screen, the
Device screen will display
what time they are required
to submit a retest.
DEVID Device ID
FVER Application version, Bootloader version
FWIM Firmware image status - conrmed or not conrmed
BATT Battery voltage, percent remaining
CHG Charging or discharging
MODE FIELD or MFGTEST
CMSN CM Serial Number
MDATE Manufacturing Year-Day-Location
CDATE Calibration Year-Day
CALR Calibration Result
BLOWS Number of blows since last calibration, total blows on this device
PIN Security Pin for server
REG Registration status
MEID Modem MEID
MPN Modem Phone Number
Cellular Device Training Manual 13
Device Screens
Queuing Test History
A queued test is displayed
in the Test History on the
device as PEND (pending).
Once the Device regains
cellular coverage, the
Test History on the Device
will reconcile with the
Monitoring Web Portal.
Queuing Compliant Test
If a Client attempts to
submit a compliant test
without cellular coverage,
the Device will store the test
results until connectivity is
restored.
Note: Queuing must be
enabled.
Test History
11/09
11/09
11/08
11/08
NEXT
BACK
to select
10:20PM
09:52AM
06:04PM
10:11PM
PEND
PEND
SENT
SENT
Connect
To Power
Retest Required
Wait 15 minutes
Send an additional
test in 15 minutes
Time: 3:09PM PDT
OK
Queuing Non-Compliant Test
If a Client attempts to submit
a non-compliant test without
cellular coverage, the device
will store the test results until
connectivity is restored. Upon
submitting a non-compliant
test, Clients will be asked to
submit a retest in 15 minutes.
Compliant Test
Has Been Stored
Test will be sent
automatically when
coverage improves.
Time: 3:09PM PDT
CLOSEHOME
Connect to Power
A battery icon will be
displayed when the battery is
too low to power the Device.
Retest Required
Wait 15 minutes
Additional test
required at
3:24PM PDT
OK
Queuing Non-Compliant Retest
After clicking “OK” on the
previous retest screen, the
Device screen will display what
time the Client is required to
submit a retest.
Charging Icon
A battery icon will be
displayed when the Device’s
battery power is low but
charging.
Charging
Cellular Device Training Manual 14
Tamper Prevenon
Infrared Digital Camera
Captures the identity of the Client
with a high-resolution photo during
a test.
Lighted Blue Ring
Assures the Soberlink
mouthpiece is properly
inserted for testing.
Air Flow Sensor
Monitors the rate and volume of
breath owing through the Device
to prevent the Client from blocking
the rear vent or giving an insufcient
amount of breath for a sample.
Alternate Air Source Detection
Detects air sources other than human
breath (e.g. air pumps, canned air)
by monitoring breath and ambient
temperature.
Cellular Device Training Manual 15
Restoring SL2 to Factory Sengs
1. Collect Device & Archive Client
Log in to the Monitoring Web Portal and click Edit under the
Client who will no longer use Soberlink.
Click the Stop Monitoring button.
The Client, along with all of their testing history, will be moved
to the Archive section of the Monitoring Web Portal.
This will “release” the Device to be activated for a new Client.
2. Reset the Soberlink Device
Power on the Device and click both display buttons (without holding them down).
This will take you to the Menu Options screen.
On the Menu Options screen, use the right display button and scroll down to Reset Device.
Highlight and select Reset Device. Then enter the button sequence: Power, Left, Right, Power.
Once successfully reset, the Device will display the “Activation Required” screen. The Soberlink Device is
ready to go back into inventory or be assigned to a new Client.
3. Reassign the Soberlink Device
To assign the Device to a new Client:
Follow the SL2 Activation Process shown on pages 7-9.
Cellular Device Training Manual
Device Specicaons
16
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Other documents
-
LifeSafer L 250 User manual
-
Apple iOS Implementatie Owner's manual
-
Guardian Interlock Systems 2030 User manual
-
STMicroelectronics X-CUBE-CLD-GEN User manual
-
Hikvision DS-PWA96-M-WE Owner's manual
-
ESET Endpoint Security for Android User guide
-
VMware Horizon Client for iOS Operating instructions
-
Lancom Systems 62035 Datasheet
-
Dell Wireless 57XX-Verizon Mobile Broadband (CDMA EV-DO) Mini-Card Owner's manual
-
SonicWALL SonicPoint NF Getting Started Manual
