Gamber-Johnson 7160-1299-10, 7160-1299-00, NotePad™ Touch Universal Tablet Cradle, NotePad™ Touch XL Universal Tablet Cradle Installation guide

  • Hello! I am an AI chatbot trained to assist you with the Gamber-Johnson 7160-1299-10 Installation guide. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
Product Mounting Disclaimer
Gamber-Johnson is not liable under any theory of contract or tort law for any loss, damage, personal injury, special, incidental or consequential damages for personal injury or other damage
of any nature arising directly or indirectly as a result of the improper installation or use of its products in vehicle or any other application. In order to safely install and use Gamber-Johnson
products full consideration of vehicle occupants, vehicle systems (i.e., the location of fuel lines, brakes lines, electrical, drive train or other systems), air-bags and other safety equipment is
required. Gamber-Johnson specifically disclaims any responsibility for the improper use or installation of its products not consistent with the original vehicle manufactures specifications
and recommendations, Gamber-Johnson product instruction sheets, or workmanship standards as endorsed through the Gamber-Johnson Certified Installer Program.
Rev. A
Product Mounting Disclaimer
Gamber-Johnson is not liable under any theory of contract or tort law for any loss, damage, personal injury, special, incidental or consequential damages for personal injury or other damage
of any nature arising directly or indirectly as a result of the improper installation or use of its products in vehicle or any other application. In order to safely install and use Gamber-Johnson
products full consideration of vehicle occupants, vehicle systems (i.e., the location of fuel lines, brakes lines, electrical, drive train or other systems), air-bags and other safety equipment is
required. Gamber-Johnson specifically disclaims any responsibility for the improper use or installation of its products not consistent with the original vehicle manufactures specifications
and recommendations, Gamber-Johnson product instruction sheets, or workmanship standards as endorsed through the Gamber-Johnson Certified Installer Program.
This instruction sheet is for the NotePad Touch - Universal Tablet Cradle only. For
instructions on features, set-up, and operation of the computer, please refer to the manual
provided by tablet manufacturer.
This cradle is designed to be used with a variety of Gamber-Johnson mounting systems.
Installation instructions for other Gamber-Johnson products are provided with each individual
product.
This instruction sheet is for the following products:
Item No. 7160-1299-00
Small
Item No. 7160-1299-10
Large
1 / 6
INSTALLATION INSTRUCTIONS
Product
Revision
Form
Printing Spec:
PS-001
7160-1299
NOTEPAD TOUCH - UNIVERSAL TABLET CRADLE
If you need assistance or have questions, call Gamber-Johnson at 1-800-456-6868
INST-893
TM
Adjustment Screw 2
Adjustment Screw 1
Barrel Key Lock
Release Button
Slam Latch
Adjustment Screw 3
Ears
Arms
Bottom Tabs
Adjusts Slam Latch Depth
Adjusts Cradle Height
VESA 75mm Mounting Pattern
1/4-20 Threads
AMPS Mounting Pattern
#10-32 Threads
1/4-20 x 0.500" hardware provided
#10-32 x 0.500" hardware provided
FEATURE IDENTIFICATION
2 / 6
Adjusts Cradle Arms
Adjustment Screws
Ears
Slam Latch
Screw 1
Latch Touching Tablet Face
Tablet
1. Loosen 3 adjustment screws and fully extend cradle
- DO NOT fully remove screws
Adjustment Instructions
All adjustments are done with a 9/64 allen wrench (provided)
2. Rotate ears counter clockwise until the tablet can fit under them
- DO NOT fully remove ears
3. Place tablet in cradle and slide slam latch onto the front of the tablet
4. Hold slam latch in place and remove the tablet, tighten screw 1
- Fit check tablet
*Example Using 7160-1299-00 With a 10" Tablet*
3 / 6
Adjustment
Screw 3
Adjustment
Screw 2
7. Double check the ears are at the correct depth
- Ears should be touching the front of the tablet but NOT pinching
6. Place tablet in cradle and slide arms in
until the ears contact the side of the tablet
- Remove the tablet and tighten screw 3
- Perform a fit check
5. Place tablet in cradle and slide bottom tabs up until they contact the tablet
- Remove the tablet and tighten screw 2
- Perform a fit check
Adjustment Instructions
Bottom Tabs
Slide Up
Slide Ears In
To Contact Tablet
4 / 6
1/4-20 Lock Nuts
"Locked" Position
"Un-Locked" Position
Adjustment Instructions
9. (Optional) Rotate the lock counter clockwise to lock the cradle
8. (Optional) Thread 1/4-20 nuts onto ear bolt to lock rotation
5 / 6
DOCKING AND UNDOCKING THE COMPUTER
OPERATION - DOCKING
1. Place the tablet into the
bottom of the cradle.
2. Rotate the tablet into the
cradle, overcoming the
resistance until the Release
Button returns to the "Latched"
position. The slam latch will
come over the front of the tablet.
There will also be an audible
confirmation as the latch system
springs downward.
3. Optional - With the dock in the
"Latched" position, turn the lock
to the "LOCKED" position
(CCW).
OPERATION - UNDOCKING
1. Turn the lock to the
"UNLOCKED" position (CW).
2. With your hand on the top of
the tablet, push up on the blue
Release Button until the
computer is free to move forward.
While the dock is "Un-Latched",
rotate the tablet forward to clear
the Slam Latch. This can be done
right or left handed.
3. Pull the tablet up to remove it
from the cradle.
6 / 6
Insert Bottom First
Rotate Top
1/6