Robur GAHP A Installation, Use And Maintenance Manual

Installation, use and maintenance manual

powered by gas and renewable energy

Modular heating unit and heater/chiller

Preassembled groups

This Installation, use and maintenance manual has been drawn up and printed by Robur S.p.A.; whole or partial

reproduction of this Installation, use and maintenance manual is prohibited.

The original is led at Robur S.p.A.

Any use of this Installation, use and maintenance manual other than for personal consultation must be previously

authorised by Robur S.p.A.

The rights of those who have legitimately led the registered trademarks contained within this publication are not

aected.

With the aim of continuously improving the quality of its products, Robur S.p.A. reserves the right to modify the

data and contents of this Installation, use and maintenance manual without prior notice.

Revision: H

Code: D-LBR563

DISPOSAL

The appliance and all its accessories must be disposed of separately in accordance with the regulations in force.

Use of the WEEE symbol (Waste Electrical and Electronic Equipment) indicates that this product cannot be disposed of as household waste.

Proper disposal of this product helps to prevent potential negative consequences for the environment and human health.

Installation, use and maintenance manual – RT__ Link

3

I Introduction .............................................................................

p.4

I.1 Recipients ..........................................................................

p.4

I.2 Control device ..................................................................

p.4

II Symbols and denitions ...............................................

p.4

II.1 Key to symbols .................................................................

p.4

II.2 Terms and denitions ....................................................

p.4

III Warnings......................................................................................

p.4

III.1 General and safety warnings ......................................

p.4

III.2 Conformity ........................................................................

p.5

III.3 Exclusions of liability and warranty ..........................

p.6

1 Features and technical data ......................................

p.7

1.1 Features ..............................................................................

p.7

1.2 Circulating pumps ..........................................................

p.7

1.3 Coding .................................................................................

p.7

1.4 Dimensions and weights ..............................................

p.9

1.5 Roma valve ......................................................................

p.19

1.6 Independent circulators selector switch

settings .............................................................................

p.20

1.7 Electrical specications ...............................................

p.21

1.8 Electronic boards ..........................................................

p.21

1.9 Operation mode ............................................................

p.21

1.10 Controls ............................................................................

p.21

1.11 Technical data ................................................................

p.22

2 Transport and positioning ........................................

p.22

2.1 Warnings ..........................................................................

p.22

2.2 Handling ...........................................................................

p.22

2.3 Group positioning ........................................................

p.22

2.4 Minimum clearance distances..................................

p.23

2.5 Mounting base ...............................................................

p.23

3 Heating engineer ...............................................................

p.23

3.1 Warnings ..........................................................................

p.23

3.2 Hydraulic system ...........................................................

p.24

3.3 Hydraulic connections ................................................

p.24

3.4 Antifreeze function .......................................................

p.27

3.5 Antifreeze liquid ............................................................

p.27

3.6 System water quality ...................................................

p.28

3.7 System lling ..................................................................

p.28

3.8 Fuel gas supply ..............................................................

p.29

3.9 Combustion products exhaust ................................

p.29

3.10 Flue gas condensate discharge ................................

p.30

3.11 Defrosting water drainage .........................................

p.30

3.12 Safety valve drain ..........................................................

p.30

4 Electrical installer ..............................................................

p.31

4.1 Warnings ..........................................................................

p.31

4.2 Electrical systems ..........................................................

p.31

4.3 Electrical power supply ...............................................

p.31

4.4 Adjustment and control .............................................

p.32

4.5 Water circulation pumps ............................................

p.36

5 First start-up ..........................................................................

p.37

5.1 Preliminary checks ........................................................

p.37

5.2 Electronic adjustment on the appliance –

Menus and parameters ...............................................

p.38

5.3 Modifying settings ........................................................

p.38

6 Normal operation ..............................................................

p.38

6.1 Warnings ..........................................................................

p.38

6.2 Switch on and o ..........................................................

p.38

6.3 Modifying settings ........................................................

p.39

6.4 Eciency ..........................................................................

p.39

7 Maintenance ..........................................................................

p.39

7.1 Warnings ..........................................................................

p.39

7.2 Pre-emptive maintenance .........................................

p.39

7.3 Scheduled routine maintenance .............................

p.40

7.4 Messages on the display ............................................

p.40

7.5 Restarting a locked-out unit .....................................

p.40

7.6 Circulators lockout ........................................................

p.41

7.7 Periods of inactivity ......................................................

p.41

8 Diagnostics ..............................................................................

p.41

8.1 Appliances/controllers ................................................

p.41

8.2 Circulating pumps ........................................................

p.41

9 Appendices..............................................................................

p.42

9.1 Wiring diagrams and internal wirings ...................

p.42

9.2 Circulating pumps ........................................................

p.48

INDEX OF CONTENTS

Introduction

4

I

I INTRODUCTION

Installation, use and maintenance manual

This Manual is an integral part of the RT__ Link and must

be handed to the end user together with the appliance.

I.1 RECIPIENTS

This Manual is intended for:

▶

End user, for appropriate and safe use of the appliance.

▶

Qualied installer, for correct appliance installation.

▶

Planner, for specic information on the appliance.

I.2 CONTROL DEVICE

In order to be able to work, the RT__ Link unit needs a control

device (DDC, CCP/CCI), which must be connected by the installer.

II SYMBOLS AND DEFINITIONS

II.1 KEY TO SYMBOLS

DANGER

WARNING

NOTE

PROCEDURE

REFERENCE (to other document)

II.2 TERMS AND DEFINITIONS

Appliance/Module (or Units) GAHP/GA/AY = equivalent

terms, both used to designate single gas-red heat/chiller ap-

pliance (GAHP A/AR/GS/WS, or GA ACF/HR/TK absorption chiller

or AY00-120 condensing boiler), part of the preassembled unit

together with other modules/appliances.

TAC = Technical Assistance Centre authorised by Robur.

CCI Controller (Comfort Controller Interface) = optional Robur

control device which lets you manage up to three modulating

heat only GAHP units (A, WS, GS).

CCP Controller (Comfort Control Panel) = Robur control de-

vice which lets you manage in modulation mode up to three

GAHP units and all system components (probes, diverter/mixing

valves, circulating pumps), including any integration boiler.

DDC Control (Direct Digital Controller) = optional Robur adjust-

ment device to control one or more Robur appliances (GAHP

heat pumps, GA chillers and AY00-120 boilers) in ON/OFF mode.

RB100/RB200 Devices (Robur Box) = optional interface devices

complementary to DDC, which may be used to broaden its func-

tions (heating/cooling/DHW production service demands, and

control of system components such as third party generators,

adjustment valves, circulators, probes).

Heat generator = equipment (e.g. boiler, heat pump, etc..) pro-

ducing heating and/or DHW.

Preassembled Group / RT__ Link = equivalent terms, both

used to designate the generic heat/chiller hydronic group con-

sisting of GAHP/GA/AY modules (see denition).

RTAR/RTCF/RTY/RTA/RTAY/RTYR/.. .Link to = initials to desig-

nate a specic heat/chiller preassembled group, consisting of a

specic combination of GAHP/GA/AY (see denition).

First start-up = preassembled group commissioning operation

that can only and exclusively be performed by a TAC.

III WARNINGS

III.1 GENERAL AND SAFETY WARNINGS

GAHP/GA/AY modules

As far as the individual GAHP/GA/AY appliances/modules

belonging to the preassembled group are concerned,

read the warnings in the respective Manuals (attached),

with particular regard to the following aspects:

 Poisoning

 Moving parts

 Burn hazard

 Pressure vessels

 Water-ammonia solution

 Limescale and corrosion

 Chloride concentration

 Aggressive substances in the air

 Switching the appliances o

Installer's qualications

Installation must exclusively be performed by a qualied

rm and by qualied personnel, with specic knowledge

on heating, cooling, electrical systems and gas applianc-

es, in compliance with the laws in force in the Country of

installation.

Declaration of conformity

Upon completing installation, the installing rm shall

issue to the owner/client the appliance's workmanlike

conformity declaration, according to national/local reg-

ulations in force and the manufacturer's instructions/

provisions.

Misuse

The preassembled group must only be used for the pur-

poses for which it has been designed. Any other use is

deemed hazardous. Incorrect use may aect operation,

duration and safety of the appliance. Adhere to the

Warnings

Installation, use and maintenance manual – RT__ Link

5

III

manufacturer's instructions.

Hazardous situations

 Do not start the preassembled group in hazardous con-

ditions such as: gas odor, hydraulic/electric/gas system

problems, parts of the unit immersed in the water or

damaged, malfunction, deactivation or exclusion of con-

trol and safety devices.

 In case of danger, request intervention by qualied per-

sonnel.

 In case of danger, switch o the electrical power and gas

supplies only if this can be done in total safety.

 Do not entrust children, persons with physical, sensory

or mental disabilities or persons with poor knowledge

and experience with use of the preassembled appliance.

Gas component tightness

 Before performing any operation on gas ducting compo-

nents, close the gas valve.

 Upon completing any procedure, perform the tightness

test according to regulations in force.

Gas smell

If you smell gas:

 Do not operate electrical devices near the preassembled

group (eg telephones, multimeters or other appliances

that can cause sparks).

 Shut o the gas supply by turning the valve o.

 Switch o the power supply via the external disconnect

switch in the power supply electrical panel.

 Ask for qualied personnel from a phone away from the

preassembled group.

Electrocution hazard

Within the preassembled group (and the appliances that

compose it) there are live parts.

 Disconnect the electrical power supply before any oper-

ation on appliance components.

 For electrical connections exclusively use compliant

components and according to the specications provid-

ed by the manufacturer.

 Make sure the preassembled group and the individual

GAHP/GA/AY modules of the same can not be reactivat-

ed inadvertently.

Connection and disconnection

For the RT__ Link electrical connection and discon-

nection operations follow the procedure described in

Paragraph 7.1

p.39

.

Earthing

Electrical safety depends on an eective earthing sys-

tem, properly connected to the preassembled group

and executed in accordance with current regulations.

Distance from combustible or ammable materials

 Do not deposit ammable materials (paper, diluents,

paints, etc.) near the preassembled group.

Acid ue gas condensate

If condensing units are present in the preassembled

group:

 Discharge the acid condensate of combustion ue gas,

as indicated in Paragraph 3.10

p. 30

, in compliance

with current exhaust regulations.

Shutting down the preassembled group

Interrupting the power supply during the operation of

the preassembled group may cause permanent damage

to the internal components.

 Except for a hazard, do not interrupt the power supply to

turn o the preassembled group, but always and exclu-

sively use the provided control device (DDC or CCP/CCI).

In the event of failure

Operations on internal components and repairs may

exclusively be carried out by a TAC, using only original

parts.

 In the event of a failure of the preassembled group, or of

one or more of the individual appliances that make it up

and/or break parts of it, refrain from any repair or restora-

tion attempt and contact the TAC immediately.

Routine maintenance

Proper maintenance ensures the eciency and good op-

eration of the preassembled group over time.

 Maintenance must be performed according to the man-

ufacturer's instructions (see Chapter 7

p. 39

) and in

compliance with current regulations.

 Appliance maintenance and repairs may only be entrust-

ed to rms legally authorised to work on gas appliances

and systems.

 Enter into a maintenance contract with an authorised

specialised rm for routine maintenance and for servic-

ing in case of need.

 Use only original parts.

Maintenance of GAHP/GA/AY modules

For the maintenance of the individual GAHP/GA/AY

modules belonging to the preassembled group, consult

their respective Manuals (attached).

Decommissioning and disposal

If the preassembled group or some of the individual

GAHP/GA/AY appliances/modules are to be dismantled,

please contact the manufacturer for disposal.

Keep the Manual

This Installation, use and maintenance manual, includ-

ing all attached documents, must always accompany the

preassembled group and must be handed to the new

owner or installer in the event of sale or transfer.

III.2 CONFORMITY

EU directives and standards

The GAHP/GA/AY modules/appliances that are part of RT__ Link,

namely the GAHP series heat pumps, GA ACF series chillers,

and AY00-120 condensing boilers comply with the essential

Warnings

6

III

requirements of the following standards and directives, each as

applicable:

▶

Eciency Directive 92/42/EEC and subsequent modica-

tions and additions.

▶

2016/426/EU "Gas Appliances Regulation" as amended and

added.

▶

2014/30/EC "Electromagnetic Compatibility Directive" as

amended and added.

▶

2014/35/EC "Low Voltage Directive" as amended and added.

▶

2006/42/EC "Machine Directive" as amended and added.

▶

2014/68/EU "Pressure Equipment Directive" as amended

and added.

▶

811/2013/EU "Energy-Related Products regulation" as

amended and added.

▶

813/2013/EU "Ecodesign requirements regulation" as

amended and added.

▶

EN 12309 appliances for gas-red heating and/or cooling

absorption.

▶

EN 378 Refrigerating systems and heat pumps.

Other applicable provisions and standards

The design, installation, operation and maintenance of the sys-

tems shall be carried out in compliance with current applicable

regulations, depending on the Country and location, and in ac-

cordance with the manufacturer's instructions. In particular, reg-

ulations regarding the following shall be complied with:

▶

Gas systems and equipment.

▶

Electrical systems and equipment.

▶

Heating and air conditioning systems, heat pumps and chill-

ers.

▶

Environmental protection and combustion products ex-

haust.

▶

Fire safety and prevention.

▶

Any other applicable law, standard and regulation.

III.3 EXCLUSIONS OF LIABILITY AND

WARRANTY

Any contractual or extra-contractual liability of the man-

ufacturer for any damage caused by incorrect installa-

tion and/or improper use and/or failure to comply with

regulations and with the manufacturer's directions/in-

structions shall be disclaimed.

In particular, the guarantee of the individual GAHP/GA/

AY modules/units belonging to the preassembled group

may be invalidated under the following conditions:

 Incorrect installation.

 Misuse.

 Failure to comply with the manufacturer's indications on

installation, use and maintenance.

 Alteration or modication of the product or any part

thereof.

 Extreme operational conditions or however outside of

the operational ranges set forth by the manufacturer.

 Damages caused by external agents such as salts, chlo-

rine, sulphur or other chemical substances contained in

the installation water or present in the air of the instal-

lation site.

 Abnormal actions transmitted to the appliance by the

system or installation (mechanical stresses, pressure, vi-

brations, thermal expansion, electrical surges...).

 Accidental damages or due to force majeure.

Features and technical data

Installation, use and maintenance manual – RT__ Link

7

1

1 FEATURES AND TECHNICAL DATA

For the characteristics of the individual modules (GAHP/GA/AY

units) that make up the RT__ Link, and of the control devices

(DDC, CCP/CCI, ...), refer to the respective Manuals (attached).

1.1 FEATURES

Preassembled groups

The RT__ Link are gas powered (natural gas or LPG) heating/

cooling sets, to supply hot and/or chilled water. Each group con-

sists of a certain number of individual gas powered modules/

heating/cooling appliances (GAHP/GA/AY units). The set of ap-

pliances and components is preassembled at the factory, form-

ing a complete hydronic group already predisposed to be simply

connected to the system.

Application

Each preassembled group according to its conguration (RTAR,

RTCF, RTY, RTAY, RTYR, RTA, ... Link) is able to simultaneously or

alternatively deliver heating, cooling, DHW production and heat

recovery, according to the needs of each single installation, with

a signicantly extensive range of heating and cooling power.

The various hydronic models (RTAR, RTCF, ... Link) are suitable

for all heating and cooling systems operating with hot and/or

chilled water, with common terminals (e.g. radiators, fan coils,

radiant panels, fan heaters, air handling units, DHW production

boilers, pool heat exchangers...), including process plants (indus-

trial heat exchangers).

Manufacturing features

Each preassembled group, in addition to the gas powered

GAHP/GA/AY heating/cooling modules/units, is composed of:

▶

delivery/return stainless steel hydraulic manifolds, insulated

with rigid cups lined with aluminum sheet

▶

galvanized steel gas outlet manifold

▶

exible connecting couplings of individual units to hydraulic

and gas manifolds

▶

condensate discarge manifold (only if A/GS/WS/AY condens-

ing appliances are included)

▶

electrical panel with protection devices (2 electrical panels

with more than 5-6 modules)

▶

bearing structure with galvanized steel sections

Composition (GAHP/GA/AY modules)

The gas heating/cooling modules that make up a RT__ Link can

be:

▶

GAHP units, A/AR/GS/WS versions, absorption heat pumps

▶

GA units, ACF/HR/TK/LB versions, absorption chillers

▶

AY unit, condensing boiler

distinguished in:

▶

aerothermal units (A, AR, ACF, HR, TK, LB)

▶

hydrothermal (WS) and geothermal (GS) units

in variable number:

▶

from 2 to 5 in the case of GAHP/GA only

▶

from 2 to 8 in the case of GAHP/GA and AY

Groups with aerothermal units must be installed exclusively out-

side, while others may be installed either indoors or outdoors.

The aerothermal modules of RT__ Links may be in conguration:

▶

with standard fans

▶

with silenced fans (S or S1)

Congurations

▶

without circulators or with circulators (standard or oversize

circulators)

▶

2, 4 or 6 pipes, ie 1, 2 or 3 pairs of delivery/return hydraulic

collectors/connections for hot and/or cold water, connected

as needed.

1.2 CIRCULATING PUMPS

Preassembled groups without water circulation pumps

If the RT__ Link is without circulators, It must be installed on the

hydraulic/primary circuit at least one circulation pump, suitably

selected and rated (by the designer/installer).

Preassembled groups with water circulation pumps

In the RT__ Links already provided with circulators, each individ-

ual GAHP/GA/AY module that is part of the group has (at least) a

single independent circulator.

The circulators are installed externally to the GAHP/

GA units, which have a special protection cover (Figure

1.14

p.19

), while for AY00-120 units the circulators are

installed internally to the unit itself.

The available head at the hydraulic connections of the preas-

sembled group should be considered net of internal pressure

drops, in the units and in the hydraulic manifolds.

Table 1.1

p. 7

provides the minimum residual head at the

nominal ow in the largest conguration.

Table1.1 Minimum residual head

residual head [m w.c.]

Wilo Yonos 25/0,5-7 2,0

Wilo Yonos 25/0,5-10 3,5

Wilo Stratos Para 25/1-11 2,0

Wilo Stratos Para 25/1-12 5,0

See the design manual for more detailed ow, head and pres-

sure drop data.

1.3 CODING

Each group is encoded with a series of letters and digits that dis-

tinguish its composition and conguration. In order:

1. (3 or 4 letters) = group type (eg RTAR, RTCF, RTAY, RTA, RTY,

...), based on composing modules (GAHP A/AR/WS/GS, GA

ACF/HR/TK/LB, AY00-120)

2. (2 or 3 digits) = cooling power, given by the sum of the cool-

ing powers of the individual modules

3. (2 or 3 digits) = heat power, given by the sum of the heat

powers of the individual modules

4. (_, /4 or /6) = number of pipes, i.e. delivery/return manifold

pairs (1, 2 or 3)

5. (2 letters) = modules type

6. (_, S, S1) = standard or silenced fans (only for aerothermal

units)

7. (MET/NAT, G25, GPL/LPG) = fuel gas (natural gas or LPG)

8. (2 or 3 letters) = country

9. (2 letters) circulators (with or without) and type (standard or

oversize)

10. (1 letter) predispositions, if any

The 1.1

p. 8

table/gure exemplies the meaning of the en-

coding in detail, providing the key for reading any possible com-

position and conguration, starting from an example.

Features and technical data

8

1

Figure1.1

Features and technical data

Installation, use and maintenance manual – RT__ Link

9

1

1.4 DIMENSIONS AND WEIGHTS

The dimensions are given for the maximum footprint

conguration.

The weights are given for the maximum weight cong-

uration.

Hydraulic/gas connections

Figure1.2 Position of water, gas and condensate discharge connec-

tions, for 2 pipes groups - Right side view

A Condensate discharge connection [1" F] (only for groups with more than

one condensing unit)

B Gas connection [1 1/2" F]

C Cold/hot water outlet [2" M]

D Cold/hot water inlet [2" M]

* The height of low-noise model is 1650 mm

Figure1.3 Position of water, gas and condensate discharge connec-

tions, for 4 pipes groups - Right side view

A Condensate discharge connection [1" F] (only for groups with more

than one condensing unit)

B Gas connection [1 1/2" F]

C Cold/hot water outlet [2" M]

D Cold/hot water inlet [2" M]

E Hot return [2" M]

F Hot delivery [2" M]

* The height of low-noise model is 1650 mm

Features and technical data

10

1

Figure1.4 Position of water, gas and condensate discharge connections, for 6 pipes groups - Top view

A Condensate discharge connection [1" F] (only for groups with more than one condensing unit). Sloping manifold, strictly connect on right side

B Gas connection [1 1/2" F]

C Cold/hot water outlet [2" M]

D Cold/hot water inlet [2" M]

E ACF HR recovery hot return (only left connection) [2" M]

F ACF HR recovery hot delivery (only left connection) [2" M]

G Hot return (only right connection) [2" M]

H Hot delivery (only right connection) [2" M]

Figure1.5 Position of water, gas and condensate connections for RTGS/WS groups - Right side view

A Condensation drain connection [1 " F]

B Gas connection [1 1/2" F]

C Hot return [2" M]

D Cold return [2" M]

E Hot delivery [2" M]

F Cold delivery [2" M]

Features and technical data

Installation, use and maintenance manual – RT__ Link

11

1

Figure1.6 Dimensions and weights of ACF/A/AR preassembled group (with 2, 3, 4 and 5 units) - front view

A 960 kg

B 1440 kg

C 1920 kg

D 2410 kg

Features and technical data

12

1

Figure1.7 Dimensions and weights of AY preassembled group (with 2, 3, 4 and 5 units) - front view

A 2 AY 330 kg

B 3 AY 450 kg

C 4 AY 580 kg

D 5 AY 700 kg

Note: The weight refers to links congured with oversize circulators

Features and technical data

Installation, use and maintenance manual – RT__ Link

13

1

Figure1.8 Dimensions and weights of ACF/A/AR + AY preassembled group (with 1+1, 1+2, 1+3, 1+4 units) - front and top view

A 1+2 790 kg (*)

B 1+3 970 kg 1+4 1070 kg (*)

(*) The weight refers to a 2 pipe link (silent ventilation, "S"), congured with oversize circulators

The GAHP/GA + 1 AY00-120 congurations are replaced

by the Gitié units.

Features and technical data

14

1

Figure1.9 Dimensions and weights of ACF/A/AR + AY preassembled group (with 1+5, 2+1 and 2+2 units) - front and top view

A 1+5 1210 kg (**)

B 2+1 1150 kg (*) 2+2 1270 kg (*)

(*) The weight refers to a 2 pipe link (silent ventilation, "S"), congured with oversize circulators

(**) The weight refers to a 4 pipe link (silent ventilation, "S"), congured on both circuits with oversize circulators

Features and technical data

Installation, use and maintenance manual – RT__ Link

15

1

Figure1.10 Dimensions and weights of ACF/A/AR + AY preassembled group (with 2+3, 2+4 and 2+5 units) - front and top view

A 2+3 1460 kg (*) 2+4 1560 kg (**)

B 2+5 1700 kg (**)

(*) The weight refers to a 2 pipe link (silent ventilation, "S"), congured with oversize circulators

(**) The weight refers to a 4 pipe link (silent ventilation, "S"), congured on both circuits with oversize circulators

Features and technical data

16

1

Figure1.11 Dimensions and weights of ACF/A/AR + AY preassembled group (with 3+1, 3+2 and 3+3 units) - front and top view

A 3+1 1630 kg (*) 3+2 1750 kg (*)

B 3+3 1880 kg (**)

(*) The weight refers to a 2 pipe link (silent ventilation, "S"), congured with oversize circulators

(**) The weight refers to a 4 pipe link (silent ventilation, "S"), congured on both circuits with oversize circulators

B

137

155415291554

137

4936

Features and technical data

Installation, use and maintenance manual – RT__ Link

17

1

Figure1.12 Dimensions and weights of ACF/A/AR + AY preassembled group (with 3+4 and 3+5 units) - front and top view

A 3+4 2060 kg (*)

B 3+5 2190 kg (*)

(*) The weight refers to a 4 pipe link (silent ventilation, "S"), congured on both circuits with oversize circulators

B

A

Features and technical data

18

1

Figure1.13 Dimensions and weights of ACF/A/AR + AY preassembled group (with 4+1, 4+2, 4+3 and 4+4 units) - front and top view

A 4+1 2120 kg (*) 4+2 2240 kg (**)

B 4+3 2380 kg (**) 4+4 2480 kg (**)

(*) The weight refers to a 2 pipe link (silent ventilation, "S"), congured with oversize circulators

(**) The weight refers to a 4 pipe link (silent ventilation, "S"), congured on both circuits with oversize circulators

A

B

Features and technical data

Installation, use and maintenance manual – RT__ Link

19

1

1.5 ROMA VALVE

Preassembled groups equipped with water circulation pumps

are also equipped with a check valve, mounted downstream of

each water circulation pump, equipped with air vent valves, as

detailed in the following Figure 1.14

p. 19

for the GAHP/GA

units and in the following Figure 1.15

p.19

for the AY00-120

units.

Figure1.14 Roma valve GAHP/GA units

A Protection cover

B Protection cover

C Valve insulation

D Roma valve

E Air-vent valve

F Air-vent valve

G Circulator

H Connection to return

manifold

Figure1.15 Roma valve AY00-120 units

D Roma valve

E Air vent

G Circulator

H Connection to return

manifold

H

E

F

G

D

Features and technical data

20

1

1.6 INDEPENDENT CIRCULATORS SELECTOR

SWITCH SETTINGS

In the RT__ Links already provided with circulators, each circu-

lator is provided with a selector switch to determine the driving

mode of the circulator itself.

For Wilo Stratos Para circulators (available as optional), the selec-

tor switch is set as shown in Figure 1.16

p.20

, depending on

the type of unit to which the circulator is connected.

Figure1.16 Wilo Stratos Para circulator selector switch setting

A GAHP A, GAHP GS/WS

B GAHP-AR, GA ACF, AY00-120

For Wilo Yonos Para circulators (standard on RT__ Links already

provided with circulators) the selector switch must be set as

shown in Figure 1.17

p.20

.

Figure1.17 Wilo Yonos circulator selector switch setting

Page is loading ...

Robur GAHP A, AY CONDENSING, GA ACF, GA ACF HR, GA ACF HT, GA ACF LB, GA ACF TK, GAHP GS, GAHP WS, GAHP-AR Installation, Use And Maintenance Manual

Related papers

Other documents