Titan Fitness High-Low Push-Pull Sled User manual

-

MPN(s): SLED3046

SKU(s): 401120

UPC(s): 737069520438

2

3

KEY

BOX

DESCRIPTION

QTY

(1) REAR FRAME 1

(2) CROSS FRAME 1

(3) REAR PLATE TREE 1

(4) CENTER PLATE TREE 1

(5) FRONT TUBE Ø50*3*508 1

(6) PLATE TREE PIPE Ø25*2.5*500 1

(7) REAR TUBE Ø50*3*899 2

(8) SKID BOARD 215*127*8 3

(9) BOLT MOUNTING PLATE 2

(10) PLASTIC TUBE CAP Ø50 5

(11) TUBE INNER BUSHING 3

(12) PLASTIC TUBE CAP Ø25 2

(13) HARD PLASTIC GASKET Ø63.5 2

(14) HARD PLASTIC GASKET Ø77 2

(15) SPRING WASHER M10 6

(16) COUNTERSUNK BOLT M10X16 6

(17) HEX BOLT M10X80 7

(18) FLAT WASHER M10 14

(19) HEX LOCK NUT M10 7

(20) FLAT WASHER M8 1

(21) SPRING WASHER M8 1

(22) HEX BOLT M8X35 1

4

SPECIAL NOTES:

− Build on a flat and level ground

− Avoid tightening bolts down entirely until the rack is assembled

− The UHMW Plastic Ski Liners are not included with the High-Low Push-Pull Sled; they can be purchased

separately

STEP 1

− Install Skid Board (8) onto Rear Frame (1) using Spring Washer M10 (15) and Countersunk Bolt

M10x16 (16).

− Insert Rear Tube (7) into Rear Frame (1) (make sure that the Tube Inner Bushing (11) is secure inside

the tube of Rear Frame (1)).

− Plug Plastic Tube Cap ø50 (10) into the top of Rear Tube (7).

5

STEP 2

− Insert Plate Tree Pipe (6) into Front Tube (5), align bolt holes, and then fasten them together

with Spring Washer M8 (21) and Hex Bolt M8x35 (22).

− Insert Hard Plastic Gasket ø77 (14) into Front Tube (5) on both left and right sides.

− Plug Plastic Tube Cap ø25 (12) into each end of the Plate Tree Pipe (6).

− Plug Plastic Tube Cap ø50 (10) into the top of Front Tube (5).

STEP 3

− Install Skid Board (8) onto Cross Frame (2) using Spring Washer M10 (15) and Countersunk Hex Bolt

M10x16 (16).

− Align bolt holes of Center Plate Tree (4) with Cross Frame (2) and Bolt Mounting Plate (9).

− Put Hex Bolt M10x80 (17) and Spring Washer M10 (15) on the bottom side, and then fasten the

assembly together with Flat Washer M10 (18) and Hex Lock Nut M10 (19) from the top side.

6

− Insert Hard Plastic Gasket ø63.5 (13) into the tube of Center Plate Tree (4) and plug the Plastic Tube

Cap ø50 (10) into the top of the tube.

STEP 4

− Align bolt holes of the Rear Frame (1) and Cross Frame (2) assemblies with that of the Bolt Mounting

Plate (9).

− Attach the assemblies by putting Hex Bolt M10x80 (17) and Spring Washer M10 (15) on the backside

and fasten them with Flat Washer M10 (18) and Hex Lock Nut M10 (19) at the front side.

− Place Tube Inner Bushing (11) into the front tube of Cross Frame (2), insert the assembly into the front

tube of Cross Frame (2). Align bolt holes of the assembly. Attach the assembly by putting Hex Bolt

M10x80 (17) and Flat Washer M10 (18) on one side and fasten them together with Spring Washer

M10 (15) and Hex Lock Nut M10 (19) on the other side.

7

STEP 5

− Align bolt holes of Rear Plate Tree (3) with

Cross Frame (2) at the rear end.

− Fasten the assembly by putting Hex Bolt

M10x80 (17) and Flat Washer M10 (18) on the

bottom side and fasten the assembly together with

Spring Washer M10 (15) and Hex Lock Nut M10

(19) from the top.

STEP 6

TIGHTEN ALL HARDWARE.

8

This concludes the SLED3046 Owner’s Manual.

If applicable to your product, make sure to tighten

all nut-and-bolt combinations before use.

Enjoy!

DISCLAIMER

This equipment must be used with care by capable and competent individuals under supervision, if necessary.

The use of any fitness equipment, including this one, involves the potential risk of injury. You accept and assume full

responsibility for any and all injuries, damages (both economic and non-economic), and losses of any type, which may

occur, and you fully and forever release and discharge Titan, its insurers, employees, officers, directors, associates, and

agents from any and all claims, demands, damages, rights of action, or causes of action, present or future, whether the

same be known or unknown, anticipated, or unanticipated, resulting from or arising out of the use of said equipment.

TITAN MAKES NO WARRANTY WHATSOEVER WITH RESPECT TO THE EQUIPMENT, INCLUDING ANY WARRANTY OF

MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, WHETHER EXPRESS OR IMPLIED BY LAW,

COURSE OF DEALING, COURSE OF PERFORMANCE, USAGE OF TRADE OR OTHERWISE. BUYER ASSUMES ALL LIABILITY IN

USE OF THE EQUIPMENT.

NEED HELP?

CONTACT US FIRST.

1 (800) 605-8241

info@titandistributorsinc.com /

Business Hours: Monday–Friday • 8:00 a.m.–5:00 p.m. (CT)

Titan Fitness High-Low Push-Pull Sled User manual

Titan Fitness High-Low Push-Pull Sled User manual

Related papers

Other documents