Assembly Instructions
BEGA
TV Unit
1 2
Read Instructions carefully. Lay out all of the components on a soft surface
Check no parts are missing. as if you were preparing to do a jigsaw puzzle.
3 4
Carefully identify each component, especially Separate and identify each component from the
those that are similar. The most common mistake hardware pack and rest each one in its proper
is getting things back to front. location before fastening.
5 6
DO NOT fully tighten screws (leave slightly
If glue is required DO NOT set until you are
loose). When the items is fully assembled certain that the parts belong together.
tighten the screws - but do not over tighten.
WARNING
FAILURE TO FOLLOW THESE BASIC STEPS CAN LEAD TO DAMAGE
THAT IS NOT COVERED BY YOUR WARRANTY
Page 2
What you Need
To Assemble the Body
(Tools not provided)
Phillips Head Screwdriver
Please make sure you have all these parts before you start.
TV Unit
(P1)
Page 3
3 x Handle
with Screw
(H1)
1 x Short
Screw
(H2)
1 x Long
Screw
(H3)
1 x Cable
Tie
(H4)
2 x L Bracket
(H5)
Step 1
You will need:
3 x Handle
with Screw
(H1)
Attach 3 x Handle to Drawer
with 3 x Screws (H1).
Tighten all Screw using a Phillips
Head Screwdriver.
Step 2
You will need:
1 x Short
Screw
(H2)
1 x L Bracket
(H5)
Attach 1 x L Bracket (H6) securely to the back top rail of the buffet using 1 x Short Screw (H3),
through the smaller hole.
Step 3
You will need:
1 x Long
Screw
(H3)
1 x L Bracket
(H5)
Locate 1 x L Bracket (H6) on the wall over a wall stud and 2 inches below the mounting bracket
secured to the back of your unit.
Attach to the wall stud using 1 x Long Screw (H4), through the smaller hole.
Page 4
(P1)
(H2)
(H5)
(P1)
(H1)
(P1)
(H5)
(H3)
ANTI TIPPING STICKER IS
LOCATED ON THE INSIDE OF
THE TOP DRAWER WHICH IS
LOCATED ON THE LEFT HAND
SIDE CORNER
Warning Sticker
Step 4
You will need:
1 x Cable
Tie
(H4)
Place the buffet into position so both mounting
brackets are vertically in line.
Lace the end of the restraint strap through the larger hole in each mounting bracket.
Bring both ends together and slide the flat end through the locking end and draw it through
until all slack is removed.
Make sure the strap is securely laced and locked.
Step 5
Guide when moving your furniture after
it is assembled.
When moving assembled furniture
(chest, side table, beds, buffets etc.) it
advised that the furniture be lifted by
two or more people.
If the furniture is dragged it can cause
damage to the furniture, and can cause
the legs to become loose.
By lifting the furniture it will avoid any
damages to your floor area.
Both of these outcomes will not be
covered by warranties.
The job is now complete!
In the interest of our environment
Please dispose of all packaging thoughtfully.
Page 4
(P1)
(H4)
-
1
-
2
-
3
-
4
-
5
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Other documents
-
Riverside Furniture 50565 Assembly Instructions
-
Home Styles 5001-0023-22 Assembly Instructions
-
-
-
-
-
Dorel DA7319-6BL User manual
-
Simpli Home AXCWAI-10 Installation guide
-
-
