urmet domus BT-1008W User manual

Brand
urmet domus
Model
BT-1008W
Type
User manual

This manual is also suitable for

DS1093-529
Mod.
1093
DS1093-529
IP KEYBORD
Ref. 1093/701
USER MANUAL
5
DS1093-529
TABLE OF CONTENTS
1 Product FeatureS .................................................................................................................. 3
1.1 Opening the package ........................................................................................... 3
1.2 Warnings .............................................................................................................. 4
2 Panel and Interface Introduction ........................................................................................ 5
2.1 Front panel and function buttons introduction ..................................................... 5
2.2 Rear panel interface introduction ......................................................................... 5
3 Keyboard function introduction ......................................................................................... 6
3.1 Connection ........................................................................................................... 6
3.2 Power on and add device ..................................................................................... 6
4 Manually add device ............................................................................................................ 7
4.1 PTZ control and image switch .............................................................................. 8
4.2 Direction control ................................................................................................... 8
4.3 Zoom .................................................................................................................... 8
4.4 Lens control .......................................................................................................... 8
4.5 Preset operation instruction .................................................................................. 9
4.6 Special function .................................................................................................. 10
4.7 Language ........................................................................................................... 11
4.8 Fig.7 ................................................................................................................... 11
4.9 LED Display ....................................................................................................... 11
4.10 IP address .......................................................................................................... 11
4.11 Exception Handing ............................................................................................. 12
5 Technical Specification ...................................................................................................... 13
ENGLISH
DS1093-529
1 PRODUCT FEATURES
This network control keyboard is a powerful three-dimensional with multi-function.
It supports:
5.0 "LED LCD HD real-time display
HDMI output
USB
ONVIF2.4
back-end PTZ.
OSD menu;
1.1 OPENING THE PACKAGE
Check that the packing and the contents are not visibly damaged. Do not attempt to work the unit if
components are missing or damaged. Contact the retailer immediately. Pack the unit in it original packing if
it needs to be replaced.
1.1.1 CONTENTS OF THE PACKAGE
1 keyboard.
1 user’s manual.
1 power supply unit
Important note:
Accessories may be changed without prior notice.
DS1093-529
1.2 WARNINGS
1.2.1 POWER
This device is powered in the range from 100 to 240 VAC. Check the power voltage before
connecting.
Use of an URMET Domus power unit with the required specifications is recommended.
Do not pull the cable to unplug the device.
Important note:
Inverting the polarity may damage the keyboard.
1.2.2 SAFETY PRECAUTIONS
Keep the device away from rain and humidity to prevent the risk of fire and electrocution.
Do not introduce solids or liquids inside the device to prevent the risk of fire and electrocution. If
this should accidentally occur, disconnect the device from the mains and have it inspected by
qualified personnel.
Never open the device. In all cases, contact qualified personnel or the service centre for repairs.
1.2.3 INSTALLATION PRECAUTIONS
Arrange the device in a well-ventilated place to prevent overheating.
For the same reason, do not install sources of heat, such as radiators or hot air ducts. Keep away
from direct sunlight. Do not install in areas subject to excessive dust, mechanical vibrations or
shocks.
Consider the working temperature of the unit (from 5°C to 45°C) and humidity range (from 10% to
90%) before choosing the installation location. High differences in temperature with respect to the
specified working temperature range can damage the unit. Do not install the unit over another unit
which generates heat.
Wait for a while before operating a device immediately after transporting it from a cold place to a
warm place and vice versa. Wait on average for three hours: this will allow the device to adapt to
the new ambient (temperature, humidity, etc.).
Do not arrange this device on an unstable surface, such as a tottering or slanted table. The device
could fall causing injury or mechanical failures.
Do not install the device in a place where it could be exposed to humidity or water. Do not direct a
jet of water onto the device: risk of fire, electrocution or mechanical failure.
Stop using the device if water or other material should penetrate inside: risk of fire and
electrocution. Contact the retailer or authorised installer.
1.2.4 CLEANING THE DEVICE
Rub delicately with a dry cloth to remove dust and dirt.
Dip the cloth in neutral detergent if dirt cannot be eliminated with a dry cloth alone.
Do not use volatile liquids (such as petrol, alcohol, solvents, etc.) or chemically treated clothes to
clean the device to prevent deformation, deterioration or scratches to the surface finish.
DS1093-529
2 PANEL AND INTERFACE INTRODUCTION
2.1 FRONT PANEL AND FUNCTION BUTTONS INTRODUCTION
Fig.1
2.2 REAR PANEL INTERFACE INTRODUCTION
Fig.2
Input power : DC12V/2A
Reserved output interface:RS485 (not available)
Power indicator
④ USB interface : it is available for connecting mouse to operate network keyboard
⑤ RJ45 network interface : through the IP switch to access network
⑥ HDMI interface :Used for connecting HD Screen to realize synchronous switch
between
keyboard LED and the HD Screen
DS1093-529
3 KEYBOARD FUNCTION INTRODUCTION
3.1 CONNECTION
Fig.3
As above picture shows, ensure the keyboard in the same LAN with the devices.
3.2 POWER ON AND ADD DEVICE
3.2.1 ADD DEVICE WAY UNDER POWER ON
When the keyboard is powered on normally, the automatic search IP interface will pop up
60min later,
as below:
After IP search finished, the user can move up and down the cursor by joystick, select IP
device
needed to access device, press ”Enter” then can save the device and display the
corresponding IP
image; when the screen displays image normally, then can be realized
to control PTZ of the front
dome.
Fig.4
Remark: The keyboard supports power-off memory function. If re-power the keyboard
and after
finish self-test, it will be restored the IP image as previous power-off.
DS1093-529
3.2.2 AUTOMATIC SEARCH AND MANUALLY ADD DEVICE
After the network keyboard connected to the front-end device, then press “Menu” on
keyboard
panel, then will pop up main menu interface as below:
Fig.5
Choose the “device management”, click “Enter” to the next sub-menu, select “search add”
and confirmation. Please move the cursor to the top to select ”search” and click “enter”,
then can search and add automatically in the network PTZ of all area network.
Select the IP
address of the image, press ”Enter ”to save the corresponding image an
d displayed.
4 MANUALLY ADD DEVICE
When access to other manufacturer’s PTZ, because of the limit of the port and PTZ
log-in
password ,there will exist that IP can’t complete add automatically, then can us
manually
add function now, the operation as below:
Click the “Enter”, select “device management”, “manual add”, enter to the following
interface:
Fig.6
DS1093-529
On the keyboard interface, input and fill in “IP address, port, name, password”, then
press
confirmation , then can display and save corresponding IP images.
Remark: 1. please check IP port, password and other information before manually add
IP
address.
Remark 2. “Menu” button is also the return button.
4.1 PTZ CONTROL AND IMAGE SWITCH
4.1.1 IP CHANNEL SWITCH
As shown above figure 4, the user can switch image channel by the corresponding
S/N with
the left of IP address list.
Press “ ”button under normal image display, and choice the corresponding S/N with
the left of IP address list. Keyboard will switch into the corresponding IP address when
you
press “ ”button. For example, switch into above figure 192.168.1.145 as the
following way:
Please press “ ”button; and press “No.3”; last press “ ”.
Remark: Image switching except through the keyboard shortcut also can be introduced
into
products through equipment management. Please select the corresponding IP
address and press
“Enter” to save to come true.
4.1.2 ROCKER OPERATION AND LENS CONTROL
On the right side of keyboard, it’s 3D vector rocker. User can easy to control PTZ and
speed.
4.2 DIRECTION CONTROL
User can pass moving rocker to control PTZ in different direction: left, right, up, down, up
left,
down left, up right, down right, rotate.
4.3 ZOOM
Zoom in: Rotating vector rocker in right direction to make the lens closer.
Zoom out:
Rotating vector rocker in left direction to make the lens farther.
4.4 LENS CONTROL
Six buttons to control lens: FOCUS+, FOCUS- ; ZOOM+, ZOOM-; IRIS+, IRIS-. These are
used for
focus, zoom and iris.
1.
Focus:
adjusting the focus distance. It can manually adjust image
via “FOCUS+, FOCUS-” buttons. (Default of camera module is automatic adjustment)
2.
Zoom:
adjusting the lens distance. It realizes zoom in and out.
3.
Iris:
Iris function means change the value of F to make image realize
bright or dim by manually adjust . (Default of camera module is automatic cursor, it is not
DS1093-529
available.)
4.5 PRESET OPERATION INSTRUCTION
Preset instruction
Preset function means that store camera state (horizontal angle, tilt angle and lens
spec) .It
can realize recover the setting state in advance and call it.
4.5.1 SET PRESET
Rotating PTZ into the target monitored position. Press setting button “ ” and choice
preset
point, for example: “ ” and press “ ” button to finish preset setting.
Remark: 1. Preset point will replace the previous recording if you save the same preset
number
as the previous saved point.
2. It’s no relate to save the quantities of presets , it is based on the front device
specification .
4.5.2 CALL PRESET
Please check if the preset point is successfully saved before you call preset. Otherwise,
the
operation is vain. Operation way as below:
1.
Press “ ” button ;
2.
Input the preset number ;
3. Press“ ” button. PTZ will automatically return to the preset point in advance.
4.5.3 DELETE PRESET
1.
Press “ ” button;
2.
Input the preset point which one do you want to delete;
3.
Press “ ” to delete preset point.
DS1093-529
4.6 SPECIAL FUNCTION
PRESET
FUNCTION
PRESET
FUNCTION
x
1080P N
x
vettorscan 2
xx
1080P P
x
Patteners1
xx
720P N
x
A-B Scan
xx
720P P
x
XXXX
x
Vectorscan 1
x
XXX
Remark: Please be noted that the special functions only for our controller. Since different
control equipment have different protocol, if use some other controller, some special
functions
probably can’t be effective.
11
4.7 LANGUAGE
There is only English Language, don’t select Chinese
Enter to the Main OSD and choice the Language you need, press the button“ ”,then it
would
be save it automatically.
As below picture show:
4.8 FIG.7
4.9 LED DISPLAY
This Keyboard controller with the 5” LED Display,and Supports Main Stream and Sub-Stream for optional.
Press the button “ ”Enter to the Main OSD，find the “System”item and choice the “Main Stream”or “Sub Stream”
,press “Enter”
Remark: LED Display could supports the Sub Stream of 4.0MP and above device,but can’t with Main
Stream.
4.10 IP ADDRESS
The Default IP address of the keyboard is “192.168.1.2”
The IP address of the camera and keyboard must be in same Network Segment ,and can’t be
same
address ,or there will be no image of the keyboard
Change the IP address of the Keyboard：
Press the button“ ”enter to the main OSD and then fine the “Network”，type into the IP address
you want.press the “Enter” to save it.after the keyboard auto-reboot,it’s changed
Successful.
Remark:The new IP address must be in same network segment with the camera.
DS1093-XXX 12
4.11 EXCEPTION HANDING
Possible Reason
Solution
The conflict IP address with the IP
camera
Change any one IP address of
the keyboard or camera
The command is inconsistent
with the actual
Confirm that the command is
same as above 2.5 item
instruction show
Input power voltage is too low
Change it with the correct power
supply
The cursor has been stuck in the
search,when you add the
device,the keyboard research
again
Move the Cursor to the IP
address to confirm which one
you want to add it
1.
Power supply doesn’t work；
2.
The master board of keyboard
is broken
1.
Change a new power supply
2.
Contact factory for
maintenance
Differences between different
manufacturers protocol
compatible
Contact factory technical to
upgrade the software
Access devices with higher
resolution, does not support more
than 1920 * 1080
Change the keyboard Stream as
Sub Stream
DS1093-XXX 13
5 TECHNICAL SPECIFICATION
Model Name
Network keyboard controller
Model
BT-1008W
Control Mode
Network
Controllable Device
Network High Speed Dome, High Speed Dome
Screen display
5.0" HD LED Display
Interface
1 RJ45, 2 RS485( reserved ), 1 DC12V, 1HDMI output, 1 USB port
Ambient Temp.
-20°~55°
Power Supply
DC12V/2A
ONVIF
ONVIF2.4
Joystick
Three-dimensional joystick
Language
Chinese/English
Access Device No.
No upper limit（display by single picture）
Image Switch Mode
Serial number or mouse
Product Size
260mm*160mm*48mm
Weight
Gross: 1.52KG / Net:1.0KG
Carton Size
300mm*210mm*160mm
DS1093-XXX 14
DS1093-529
URMET S.p.A.
10154 TORINO (ITALY)
VIA BOLOGNA 188/C
Telef. +39 011.24.00.000 (RIC.AUT.)
Fax +39 011.24.00.300 - 323
Area tecnica
servizio clienti +39 011.23.39.810
http://www.urmet.com
e-mail: info@urmet.com
MADE IN CINA
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14

urmet domus BT-1008W User manual

Brand
urmet domus
Model
BT-1008W
Type
User manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents