SportsArt G862 Owner's manual

Sports Art Industrial Co., Ltd. TUV-CERT ISO 9001/9002/14000 Certied Quality Products 2012.07.22

G862 Elliptical Trainer

Owner’s Manual

G862 OWNER’S MANUAL CONTENTS

1. INTRODUCTION .............................................................................. 2

2. SAFETY PRECAUTIONS ................................................................ 3

3. LIST OF PARTS ............................................................................... 5

4. ASSEMBLE THE PRODUCT ........................................................... 7

STEP 1 Unbox the Unit ........................................................................ 7

STEP 2 Assemble the Pedestal............................................................ 8

STEP 3 Install the Upper Cover............................................................ 9

STEP 4 Install Stride Linkages and Footplate Carriages. .................... 9

STEP 5 Install Left/Right Supports ....................................................... 10

STEP 6 Secure the Rail Base Cover ................................................... 11

STEP 7 Move the Unit into Place ......................................................... 12

STEP 8 Level the Unit .......................................................................... 13

STEP 9 Understand the Green System .............................................. 14

STEP 10 Install the Boost Converter ................................................... 15

STEP 11 Connect Boost Converters .................................................... 16

STEP 12 Establish the Number of Units per Pod ................................ 17

STEP 13 Install the CES, if Desired .................................................... 18

STEP 14 Avoid Safety Hazards ........................................................... 19

5. UNDERSTAND THE G862 DISPLAY ............................................... 20

DISPLAY Overview .............................................................................. 21

DISPLAY Specications ....................................................................... 21

DISPLAY Windows ............................................................................... 21

DISPLAY Keys ...................................................................................... 21

6. OPERATE THE PRODUCT ............................................................. 23

OPERATION Quick Start ..................................................................... 23

OPERATION Start a Workout Program ............................................... 23

OPERATION Cool Down ..................................................................... 24

OPERATION Workout Programs ......................................................... 24

OPERATION User Preferences and Component Versions................... 27

7. ABOUT HEART RATE DETECTION ................................................ 28

HEART RATE Telemetry ...................................................................... 28

HEART RATE Contact ......................................................................... 28

8. GUIDELINES FOR EXERCISE ....................................................... 29

9. MAINTENANCE ............................................................................... 30

MAINTENANCE Error Messages ........................................................ 30

MAINTENANCE Lubricate the Shoulder Area ..................................... 30

MAINTENANCE Lubricate the Stride Mechanism ............................... 31

MAINTENANCE Clean the Glide Rail .................................................. 32

MAINTENANCE Schedule ................................................................... 33

MAINTENANCE Task List (Elliptical Trainers) ..................................... 34

MAINTENANCE One-Year Maintenance Log ...................................... 35

MAINTENANCE Boost Converter Disconnection ................................. 36

MAINTENANCE Electronics Block Diagram ........................................ 38

10. SAFETY PRECAUTIONS IN FRENCH .......................................... 39

2

1. INTRODUCTION

Congratulations on your purchase of one of the nest exercise products on the market

today, the SportsArt G862 elliptical trainer. Constructed of high quality materials and

designed for years of reliable usage, this product was made to become an integral

part of your commercial tness venue.

Before this product is assembled or operated, we recommend that you famil-

iarize yourself with this manual. Understanding the correct methods of assembly

and operation will help ensure that exercisers obtain their tness goals safely and

successfully.

3

2. SAFETY PRECAUTIONS

This product was designed and built for optimum safety. However certain precau-

tions apply during the use of this product. Please note the following safety

precautions:

• Please read the entire manual before assembly and operation. Make

sure the product is installed and operated as instructed in this manual.

• Assemble and operate the product on a solid, level surface. Do not use

outdoors or near water, including pools and saunas.

• Check the product before every use. Make sure all parts are assem-

bled, and all fasteners are tightened. Do not use the product if it is disas-

sembled in any way.

• Wear proper workout clothing. Do not wear loose clothing. Do not wear

shoes with leather soles or high heels. Tie all long hair back. Do not go

barefoot on this product.

• Keep away from moving parts. Moving parts may or may not stop imme-

diately if an object becomes caught or impedes normal motion.

• Use this product only for its intended purpose as described in this

manual.

• Be careful when mounting and dismounting the unit.

• Never operate this product if it has been damaged in any way. If it is

not working properly, or has been dropped or damaged, contact a service

technician for repairs.

• Do not use accessories that are not specically recommended by the

manufacturer. Such parts might cause injuries or cause the unit to fail.

• Keep all air ventilation areas free of blockage. Never drop or insert any

object into any opening.

• Do not operate where aerosol (spray) products are being used or where

oxygen is being administered.

• This product is not intended for use by persons (including children) with

reduced physical, sensory, or mental capabilities, or by people who are

otherwise decient in product knowlege or experience. If such people use

this product, they should be given training and be supervised at all times

by someone responsible for their safety.

• Children should be supervised to ensure that they do not play on or

near the product.

• The user weight limit for this product is 227 kg, 500 lb. At maximum

resistance, this product meets standards for users up to 150 kg, 330 lb.

CAUTION: If you feel any pain or abnormal sensations, STOP YOUR

WORKOUT and consult your physician immediately. Work within your

recommended exercise level. DO NOT work to exhaustion. Before beginning

any exercise program, you should consult with your doctor. It is recommended that

you undergo a complete physical examination.

WARNING! Heart rate monitoring systems may be inaccurate. Too much exercise

may result in serious injury or death. If you feel faint, stop exercising immediately.

4

2. SAFETY PRECAUTIONS (CONTINUED)

Note: This equipment has been tested and found to comply with the limits for a Class

B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference in a residential instal-

lation. This equipment generates, uses and can radiate radio frequency energy and,

if not installed and used in accordance with the instructions, may cause harmful

interference to radio communications. However, there is no guarantee that inter-

ference will not occur in a particular installation. If the user desires to correct the

interference, it is at the user’s own expense.

WARNING! Only qualied technicians should be allowed to contact electrical

components such as circuit boards. Some components carry an electrical charge

even after use has been discontinued or the product has been unplugged. For

products with power cords, turn off unit power, wait ve minutes, then disconnect

the power cord from the power socket. For products without power cords, let the unit

sit without use for ve minutes. Only after taking such precautions should covers be

removed and electrical components be accessed.

For French speaking people in North America, please note that there is a

sticker in the owner’s manual. Please adhere the sticker (above center) onto

the product as shown. The sticker will not be placed in manuals sent to other

areas.

5

3. LIST OF PARTS

Assembly Parts

No. Name Qty. No. Name Qty.

A1 Main body 1 A7 Right footplate assembly 1

A1A Rail base cover 1 A8 Right base cover 1

A2 Small cover 1 A9 Left base cover 1

A3 Upper cover 1 A10 Hardware kit 1

A4 Right support 1 A11 Boost converter 1

A5 Left support 1 A12

Boost converter

connector cable

1

A6 Left footplate assembly 1

6

Components on the Product

No. Name Specication Notes

41 Phillips screw M5*D0.8*L10

42 Mushroom top Phillips screw M4*L16

43

Inner hex screw M8*L25

Spring washer M8

Washer D17*d8.3*t1.0

44

Inner hex screw M6*L15

Serrated washer D20*d6.2*t2.0*19T

45

Inner hex screw 5/16”*L2-1/4 inch

Seat roller washer D17*d8*t2.0

46

Roller axle

Flat washer D21*d10.5*t2

Lock nut M10

47

PU sheath D12*D8*L45

Axle M5*L71

Flat washer D10*d5.2*t1

Mushroom top inner hex screw M5*6

48 Bevelled head Phillips screw M6*P1.0*L10

Components in the Hardware Kit

No. Name Qty. Specication Notes

33 Mushroom top Phillips screw 6 M4*L16

34

Inner hex head screw 3 M8*L20

Spring washer 3 M8

Serrated washer 3 D18*d8.5*t2.0*19T

Gasket 3 D13*0.25

35 Left/right adjustment rod cover 2

36 Screw insert 4

37

M10 nut cap 2

38 Screw cap 2

L-shaped Allen wrench 1 M6

L-shaped Allen wrench 2 M4

Double open-end wrench 1 8*17

Double open-end wrench 1 13*19

T-shaped Allen wrench 1 M5

Screwdriver shank 1 at and Phillips

Screwdriver handle 1 green

7

4. ASSEMBLE THE PRODUCT

Follow instructions below to assemble this product. Note that in this manual

the words “left” and “right” are used to refer to the product and its parts. As

such, these designations correspond to the “left” and “right” sides of a person

in position to exercise on this product. Also, for brevity, the word “screws” is

used where screws, washers, and other hardware may be involved.

STEP 1 Unbox the Unit

Please follow instructions A through D to remove packaging material and to

place the unit on top of the flattened cardboard.

A. Remove the box top and the plastic sheet.

B. Start working from above, first removing Styrofoam (2) above the unit.

C. Lift Styrofoam (3) on both sides of the unit upward to remove it. Place

parts aside separately.

D. Lift the pedestal to remove Styrofoam (1) in the middle.

8

STEP 2 Assemble the Pedestal

Please follow instructions (a) through (b) to assemble the pedestal.

(a) First, lift the pedestal upright. Be careful to avoid pinching the data cable.

(b) Secure screws (34), first in area A, then in area B.

(a)

(b)

A

B

9

STEP 3 Install the Upper Cover

Please follow instructions (a) through (d) to install the upper cover.

(a) Slide the water

guard up the

pedestal. (This

ring must be

placed above the

upper cover.)

(b) Install the upper

cover and secure

it with screw (33).

(c) Install the

small cover (A2)

and secure it with

screw (33).

(d) Slide the water

guard down the

pedestal until it fits

snugly against the

covers.

STEP 4 Install Stride Linkages and Footplate Carriages

Please follow steps (a) through (f) to install stride linkages and footplate

carriages on both sides of the product.

(a) Remove bolts (45) from the bushing on the stride adjustment mechanism.

(b) Align the hole in the stride linkage with the bushing on the stride adjustment

mechanism, and

press the stride

linkage into place

on the bushing.

Secure the stride

linkage with bolts

(45). Then insert

the stride linkage

cover (35) into

place. Follow the

same procedure

on both sides.

(c) Remove bolt

(46) from the left

footplate carriage.

(d) Remove screw

(47) from the left

footplate carriage

(A6).

(b)

(c)

(d)

(a)

(d)

(b)

(a)

(c)

10

STEP 5 Install Left/Right Supports

Please follow instructions (a) through (f) to install left and right supports.

(a) Remove screws and

remove covers from

the top of the left and

right supports.

(b) Remove screws (43)

(44) from both sides.

(c) Put left and right

supports (A4,A5) into

place and then loosely

secure screws (43) at

the top. Do not fully

secure these screws

yet.

(d) First, secure screws

(44) at the base of the

supports (A4,A5). Then

go back to the top and

secure screws (43).

STEP 4 Install Linkages/Carriages (Continued)

(e) Insert the front of the footplate carriage into

the vertical arm. Align it with the hole and use

bolt (46) to secure it into place. Then insert caps

(37, 38) into place.

(f). Lubricate the area where the rod contacts the

bushing, hold the footplate carriage into place,

and secure it with screw (47). Perform the same

actions on both sides of the product.

(e)

(f)

(d)

(c)

(b)

(a)

11

STEP 6 Secure the Rail Base Cover

Please follow instructions (a) through

(b) to install the rail base cover.

(a) First, insert screw inserts (36) into

the rail base plate.

(b) Set the rail base cover (A1A) in

place and secure it with screws (33).

STEP 5 Install Left/Right Supports (Continued)

(e) First, remove screws (41)

from the lower part of the

supports. Snap covers (A4,

A5) into place on the left and

right supports (A8, A9). Then

secure screws (41).

(f) Set upper covers into

place on both supports, and

secure them with screws

(42).

(e)

(f)

12

STEP 7 Move the Unit into Place

Follow steps (a) through (c) to move the unit into place for use.

(a) Stand behind the unit. Grasp the glide track rods as shown.

(b) Lift up. (To avoid injury, always use proper lifting techniques.)

(c) Push while using the transport wheels to roll the unit into place.

(b)

(a)

(c)

13

STEP 8 Level the Unit

If the unit does not rest flat on the floor, please follow steps (a) through (b)

to level it.

(a) Under the front of the unit, rotate the leveler nut upward to enable

adjustment of the leveler foot. Then screw the leveler foot downward until it

touches the floor. Rotate the leveler nut against the product frame to secure

this position. Carry out these instructions on both sides of the product.

(b) Under the support, rotate the leveler nut upward to enable adjustment of

the leveler foot. Then screw the leveler foot downward until it touches the

floor. Rotate the leveler nut against the product frame to secure this position.

(a)

(b)

14

STEP 9 Understand the Green System

The G862 elliptical trainer is designed for use in a power production system

called the Green System. For more information about this system, please

refer to the inverter and boost converter installation manuals. Instructions

below pertain to installation of the boost converter. One boost converter

must be connected to each Green System fitness product.

15

STEP 10 Install the Boost Converter

Please follow instructions (a) through (c) to connect the boost converter to

G862 elliptical trainer.

(a) First, remove screws (48) from the front of the unit (A1).

(b) Connect cords from the boost converter (A11) into connectors (A) and

(B) on the product. In area (A), follow sequence , first inserting the

connector end , then rotating it to secure it into place . (Listen for the

“click” sound, and look to make sure the connector is inserted fully.) In area

(B), directly insert the connector end.

(c) Insert the boost converter (A11) into the product (A1), align the holes, and

use screws (48) to secure it into place. Note: Fully secure the screws so the

heads are flush with the connector plate.

(c)

(a)

(b)

B

A

1

2

16

STEP 11 Connect Boost Converters

Before assembling components, make sure that the power supplies on

the fitness products and the boost converters are in the off position. First,

remove the protective cover from the boost converter (A11). Insert the boost

converter connector cord (A12), and secure it into place. On the last fitness

product in a series of products, only remove the protective cover where a

cable will be connected. On the unconnected side, leave the protective cover

in place.

17

STEP 12 Establish the Number of Products per Pod

Upon setup, the number of fitness products per pod must be entered into the

memory of each product. If this is not done properly, the inverter might get

overloaded and its fuse might break. The procedure to establish the number

of fitness products per pod is explained below.

First, some background information:

● A group of tness products connected to one inverter is called a pod.

● The number of tness products per pod determines the maximum power

output per unit.

● One inverter can process up to 2000 watts of power. For a maximum of

Green System tness products, please contact your local distributor.

● In general, the fewer tness products per pod, the higher the power out-

put limit per unit. However, since the maximum power output is capped at

250 watts per unit, tness products in pods with eight or fewer units have a

maximum output of 250 watts per product.

● For pods with eight or more units, the maximum output per product is

calculated by a formula: Divide 2000 (maximum watts produced by one

Green System) by the number of tness products in the pod. For example,

for a ten-unit pod, calculate 2000/10=200. The maximum power output of

each unit in the 10-unit pod would be 200 watts. (This is the factory default

setting.) The power output limit of a product is calculated automatically once

the number of units in the pod has been established.

At setup, follow the procedure below to enter into each fitness product the

number of units in the pod.

1. Simultaneously press and hold WORKOUT LEVEL▲ ＋ WORKOUT

LEVEL ▼ ＋ CHANGE DISPLAY keys for two seconds. This will activate

the units-per-pod setting mode.

2. The message screen will show “PASSWORD-0000”. The passcode,

8250, must be entered before the number of units in the pod can be entered.

Follow instructions below to enter the passcode.

a. Use numeric keys 0 through 9 to enter the first digit of the four-digit

passcode 8250. After inputting the first digit, 8, press the ▼ key to confirm

your choice.

b. Then input the next number, 2, followed by the ▼ key. Proceed in this

fashion until all four digits of the passcode have been entered. If necessary,

press the ▲ key to return to a preceding entry. Then press the correct

numerical key. After inputting a number, always press the ▼ key to confirm

your choice.

c. After the four-digit passcode has been entered correctly, the product will

automatically enter the units-per-pod setting mode.

18

STEP 12 Establish the Number of Units per Pod (Cont.)

The previous (or default) number of units per pod will appear in the setting

value screen, and the following message will appear in the dot matrix screen:

“ENTER NUMBER OF CARDIO PRODUCTS CONNECTED”.

a. Press ▲/▼ keys or numeric keys (0 through 9) to input the number of

products in the pod.

b. If desired, press the CLEAR key to reset all values to zero.

c. After the correct number of units in the pod has been entered, press the

ENTER key to commit the number to the product memory. After the ENTER

key has been pressed, the unit-per-pod setting mode will end.

d. If desired, press the STOP key at any time to exit this mode and maintain

the previous setting.

At this point, the Green System is ready for use.

STEP 13 Install the CES, if Desired

The G862 elliptical trainer can operate with the CardioActive™ Entertainment

System, an integrated TV module. If desired, install the integrated TV module

after the elliptical trainer is fully assembled. For more information, please

refer to installation instructions for the CardioActive Entertainment System.

19

STEP 14 Avoid Safety Hazards

While the product is in use, or during maintenance or repair work, be careful

to avoid getting pinched by or wedged against moving parts. In particular,

do not insert fingers or other body parts into the stride adjustment area or

the opening in the front covers. Prevent injuries to yourself and others by

employing safe practices at all times.

Page is loading ...

SportsArt G862 Owner's manual

SportsArt G862 Owner's manual

in other languages

Related papers

Other documents