Toro Float Kit, GrandStand Multi Force Mower or Snow Machine Installation guide

Brand: Toro

Model: Float Kit, GrandStand Multi Force Mower or Snow Machine

Type: Installation guide

FormNo.3429-917RevA

FloatKit

GrandStand

MultiForceMowerorSnowMachine

ModelNo.136-8350

InstallationInstructions

Safety

SafetyandInstructional

Decals

Safetydecalsandinstructionsareeasilyvisibletotheoperatorandarelocatednearanyarea

ofpotentialdanger.Replaceanydecalthatisdamagedormissing.

decal136-5708

136-5708

1.Lower2.Float

Installation

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

ProcedureDescription

Qty.

Use

Nopartsrequired

–

Preparethemachine.

Switch

Wireharness1

Relay2

Decal1

Installthekit.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3429-917*A

PreparingtheMachine

NoPartsRequired

Procedure

1.Parkthemachineonalevelsurface.

2.DisengagethePTO,engagetheparkingbrake,

andmovethemotion-controlleversoutwardto

theNEUTRAL-LOCKposition.

3.Shutofftheengineandremovethekey.

4.Removethenegative(-)batterycablefromthe

battery.

InstallingtheKit

Partsneededforthisprocedure:

Switch

1Wireharness

2Relay

1Decal

Procedure

1.Lowertherearcushion.

2.Drillaholeatthelocationnearthekeyswitch

asshowninFigure1.

g212536

Figure1

1.26mm(1inch)3.29mm(1.1inch)

2.Hole—12mm(1/2inch)

diameter

3.Removethehexnutfromtheswitch,insertthe

switchthroughthehole,withtheslotontheleft,

andusethenuttosecureit(Figure2).

g220212

Figure2

1.Switch3.Slot

2.Nut

4.Connecttheswitchconnector(P06)fromthe

wireharnesstotheswitch(Figure3).

g214830

Figure3

1.Wireharness4.Relay

2.Switchconnector(P06)5.Relayconnector(P05)

3.Switch6.Relayconnector(P04)

5.Installthe2relaysontotherelayconnectors

(P04andP05)asshowninFigure3.

6.DisconnecttheLowFlowKitwireharness

fromthecontrollerharnessandplugitintothe

manifoldconnector(P01)ofthekitwireharness

(Figure4).

g214828

Figure4

1.Controllerharness

connector

3.LowFlowKitconnector

2.Switchboxconnector

(P02)

4.Manifoldconnector(P01)

7.Plugthecontrollerharnessconnectorintothe

switchboxconnector(P02)asshowninFigure

8.RemovethediodefromtheLowFlowKitwire

harness,plugthecontrollerharnessconnector

(P03)intothatconnector,andplugthediodeinto

thediodesocket(P07)asshowninFigure5.

g214829

Figure5

1.LowFlowKitdiode

connector

3.Diodesocket(P07)

2.Controllerharness

connector(P03)

4.Diode

9.Installthedecalinfrontoftheswitch(Figure6).

g220331

Figure6

1.Decal

10.Installthenegative(-)batterycabletothe

battery.

11.Startthemachineandverifytheoperationofthe

switch;refertoUsingtheFloatSwitch(page4).

Operation

UsingtheFloatSwitch

MovetheswitchtotheFLOATposition(Figure7)and

presstheleftswitchonthelow-owcontrollertoallow

theattachmenttofollowthecontouroftheground

(Figure8).Presstheleftswitchonthelow-ow

controllerrearwardtodisengagetheoatmodeand

raisetheattachmentofftheground.Movetheoat

switchtothenormaloperatingpositiontocontrolthe

attachmentusingLowFlowHydraulicKit.

g210832

Figure7

1.Lowertonormaloperating

position

2.Floatposition

g223023

Figure8

1.Presstoengageanddisengageoatmode

Toro Float Kit, GrandStand Multi Force Mower or Snow Machine Installation guide

Toro Float Kit, GrandStand Multi Force Mower or Snow Machine Installation guide

Toro Float Kit, GrandStand Multi Force Mower or Snow Machine Installation guide

Related papers

Other documents