V-038 Easy Guide
Please read these instructions carefully before using the Vax Detailer.
For advice or assistance, call
Vax Care on 0870 606 1248
www.vax.co.uk
handheld vacuum for small spaces
PRODUCT FEATURES
a On/off button
b Filter inside dust container
c Dust container
d Charging indicator
e Charging base
f Brush attachment
g Charger inlet
h Charger
a
b
c
d
e
f
g
h
CHARGING
1. Remove the cleaner from the charging base.
2. Press the power button and hold down to vacuum dry dust and debris. Release to
shut cleaner off.
1. Grasp the dust container and remove by gently pulling away from the main body.
2. Pull the filter out and empty contents into a waste bin. Remove any extra debris
from the filter and then replace in the dust container.
3. To replace the filter, line up the 3 notches in the filter with the 3 tabs on the dust
container. Firmly press the filter into the dust container and check the alignment of
the filter. NOTE: Dust may escape through the vents if the filter is mis-aligned.
4. Re-attach the dust container.
1. Slide the brush attachment into the vacuum nozzle as needed. Remove when finished.
2. Store on charging base when not in use.
The Vax Detailer is designed to sit in the charging base on a flat surface or mounted
vertically on a wall.
HOW TO OPERATE
DUST CONTAINER AND FILTER: REMOVAL AND REPLACEMENT
ATTACHMENT USAGE
CHARGING BASE/INSTALLATION
NOTE: Only use the C-038 charger supplied by Vax.
CHARGE FOR 24 HOURS BEFORE FIRST USE.
1. Connect charger unit to mains socket outlet.
2. Plug the charger into the charger inlet on the charging base, ensuring thatthe dust
container nozzle interlocks with the tab nearest the chargingindicator. Push the
handle down until it clicks securely into place.The charging indicator will light when
the unit is charging.
DUST CONTAINER AND FILTER: REMOVAL AND REPLACEMENTDUST CONTAINER AND FILTER: REMOVAL AND REPLACEMENTDUST CONTAINER AND FILTER: REMOVAL AND REPLACEMENT
For mounting on the wall:
1. Mark two screw hole centres vertically 76mm (3") apart. Checking that there is
room to fit the Vax Detailer and charging base near a mains socket outlet.
IMPORTANT: WHEN DRILLING, ENSURE THAT YOU ARE CLEAR OF ANY
HIDDEN CABLING OR PIPEWORK.
2. Drill a 4.5mm (3/16”) hole through the centre of each mark.
3. Push the plastic wall plugs (supplied) into the drilled holes.
4. Tighten the screws into the wall plugs, leaving 6.5mm (1/4”) between the screw
head and the wall surface.
5. Slide the charging base onto the screws. Adjust the screw clearance as needed to
ensure a tight fit.
Keep the charger plugged in to a mains socket at all times. It is normal for the
charger to become warm to the touch when charging. If the operating time gets
shorter after repeated use, let the unit run until its charge is exhausted, then
recharge for 24 hours. Repeat this monthly for best results.
THIS PRODUCT IS INTENDED FOR INDOOR HOUSEHOLD USE ONLY. PLEASE SAVE THESE INSTRUCTIONS.
When using an electrical appliance, basic precautions should always be followed,
including the following:
• READ ALL INSTRUCTIONS BEFORE USING THE APPLIANCE.
• ALWAYS FOLLOW THESE SAFETY INSTRUCTIONS.
WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR INJURY:
• For indoor use only. Do not use outdoors or on wet surfaces.
• Do not charge the unit outdoors.
• Use only as described in this easy guide. Use only the manufacturer's recommended
attachments.
• Do not use with a damaged cord or plug.
• Do not abuse the cord. Never carry the charger or base by the cord or yank to
disconnect from a mains socket; instead grasp the charger and pull to disconnect.
Keep the cord away from heated surface. Do not pull the cord around sharp edges
or corners. Do not close the cord in a door.
• Do not handle the plug or appliance with wet hands.
• This product includes rechargeable nickel cadmium batteries. Do not incinerate
batteries or expose to high temperatures, as they may explode.
• Unplug the charger from the mains before any routine cleaning or maintenance.
• Do not place any objects in the openings on your vacuum.
• Do not use with any opening blocked; keep free of dust, lint, hair, and anything that
may reduce airflow.
• Keep hair, loose clothing, fingers and all parts of the body away from openings and
moving parts.
• Do not pick up anything that is burning or smoking, such as cigarettes, matches or
hot ashes.
• Do not use without the filter in place.
• Do not pick up flammable or combustible liquids such as gasoline or use in areas
where they may be present.
• Use only the charger supplied by the manufacturer to recharge.
Waste electrical products should not be disposed of with household waste.
Please recycle where facilities exist. Check with your local authority or
retailer for recycling advice.
CHARGING BASE/INSTALLATION
IMPORTANT SAFETY INSTRUCTIONS
Manufacturer/EEC importer: Vax Limited, hereby on our own responsibility declare
that the product V-038 Detailer is manufactured in compliance with the following:
Safety: 73/23/EEC Low Voltage Directive, as modified by 93/68/EEC
EMC: 89/336/EEC Electromagnetic Compatibility Directive, as modified by 93/68/EEC
Vax Ltd., Kingswood Road, Hampton Lovett, Droitwich, Worcestershire, WR9 OQH, UK.
Version 1
BATTERY DISPOSAL
EEC STATEMENT OF COMPLIANCE
-
1
-
2
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI