Highlite International B.V. – Vestastraat 2 – 6468 EX – Kerkrade – the Netherlands
Infinity B401 Beam V1
Order code: 41533
MANUAL
ENGLISH
1
Order code: 41533
Infinity B401 Beam
Table of contents
Warning ............................................................................................................................................................................... 3
Safety Instructions ......................................................................................................................................................... 3
Operating Determinations .......................................................................................................................................... 5
Rigging ............................................................................................................................................................................ 5
Connection with the Mains ......................................................................................................................................... 6
Return Procedure .......................................................................................................................................................... 7
Claims .............................................................................................................................................................................. 7
Description of the Device ................................................................................................................................................ 8
Output .......................................................................................................................................................................... 8
Electrical ...................................................................................................................................................................... 8
Control ......................................................................................................................................................................... 8
Optical System ........................................................................................................................................................... 8
Movement ................................................................................................................................................................... 8
Gobos and Colors ..................................................................................................................................................... 8
Physical ........................................................................................................................................................................ 8
Certification and Safety ........................................................................................................................................... 9
Front View ....................................................................................................................................................................... 9
Back View .....................................................................................................................................................................10
Installation .........................................................................................................................................................................10
Installing the Lamp ......................................................................................................................................................11
Lamp Adjustment .......................................................................................................................................................13
Lock/Unlock the Moving Head ................................................................................................................................14
Setup and Operation ......................................................................................................................................................15
Control Modes .............................................................................................................................................................15
One Infinity (Stand-alone/Auto programs) .........................................................................................................15
One Infinity (Manual) ..............................................................................................................................................15
Multiple Infinitys (DMX control) ..............................................................................................................................16
Multiple Infinitys (Wireless DMX Control) ..............................................................................................................17
Connect the Infinity to the Wireless DMX Signal Transmitter ...........................................................................18
Disconnect the Infinity from the Wireless DMX Signal Transmitter ..................................................................18
Multiple Infinitys (Art-Net/sACN Control/RDM) ...................................................................................................19
Connecting to a Network .........................................................................................................................................20
Art-Net Settings .........................................................................................................................................................20
sACN Settings............................................................................................................................................................20
How to Make a Data Cable .....................................................................................................................................21
Software for Controlling .............................................................................................................................................21
Fixture Linking ...............................................................................................................................................................22
Data Cabling ...............................................................................................................................................................22
Control Panel ...............................................................................................................................................................23
DMX Addressing ..........................................................................................................................................................23
Menu Overview ...........................................................................................................................................................24
Start-up..........................................................................................................................................................................28
Screen Lock .................................................................................................................................................................29
No Reset Start-up ........................................................................................................................................................29
Main Menu Options ....................................................................................................................................................30
1. DMX Addressing ...................................................................................................................................................30
2. Control Mode .......................................................................................................................................................31
2.1. User Personality .................................................................................................................................................31
3. Settings Menu .......................................................................................................................................................32
3.1. Network Settings ...............................................................................................................................................34
3.2. Lock Code .........................................................................................................................................................35
3.3. Touch Calibration .............................................................................................................................................36
3.4. Lamp Settings ....................................................................................................................................................36
3.5. Special Set (Maintenance Timer) ..................................................................................................................37
2
Order code: 41533
Infinity B401 Beam
3.6. Service Menu.....................................................................................................................................................37
3.7. Reset Function ...................................................................................................................................................38
3.8. Factory Settings.................................................................................................................................................39
4. Manual Control ....................................................................................................................................................39
4.1. Test Run ...............................................................................................................................................................40
4.2. Manual Mode ...................................................................................................................................................40
5. Stand-Alone ..........................................................................................................................................................40
6. Information ............................................................................................................................................................41
6.1. Fixture Information ............................................................................................................................................41
6.2. Fan Information .................................................................................................................................................42
6.3. Error Information ...............................................................................................................................................42
6.4. Channel Information ........................................................................................................................................43
DMX Channels .............................................................................................................................................................44
18 Channels (Basic Personality) ............................................................................................................................44
23 Channels (Advance Personality) ....................................................................................................................50
How to Create Color Bump Effect .......................................................................................................................55
Maintenance ....................................................................................................................................................................56
Replacing the Lamp ..................................................................................................................................................56
Replacing the Fuse .....................................................................................................................................................56
Static Gobo Wheel and Color Wheel ..........................................................................................................................57
Troubleshooting ...............................................................................................................................................................57
No Light .........................................................................................................................................................................57
No Response to DMX..................................................................................................................................................57
Error Messages .............................................................................................................................................................59
Product Specifications ....................................................................................................................................................60
Approval ...........................................................................................................................................................................61
Dimensions ........................................................................................................................................................................61
Moving Head Position / DMX Values ...........................................................................................................................62
3
Order code: 41533
Infinity B401 Beam
Warning
Unpacking Instructions
Immediately upon receiving this product, carefully unpack the carton and check the contents to ensure
that all parts are present, and have been received in good condition. Notify the dealer immediately and
retain packing material for inspection if any parts appear damaged from shipping or the carton itself
shows signs of mishandling. Save the carton and all packing materials. In the event that a fixture must be
returned to the factory, it is important that the fixture be returned in the original factory box and packing.
Your shipment includes:
● Infinity B401 Beam
● 2 x mounting brackets with quick locks
● Schuko to PowerCON True1 power cable (1,5 m)
● User manual
Safety Instructions
Every person involved with the installation, operation and maintenance of this device has to:
● be qualified
● follow the instructions of this manual
Before the initial start-up, please make sure that there is no damage caused by transportation.
Should there be any, consult your dealer and do not use the device.
To maintain perfect condition and to ensure a safe operation, it is absolutely necessary for the user to
follow the safety instructions and warning notes written in this manual.
Please consider that damages caused by manual modifications to the device are not subject to
warranty.
This device contains no user-serviceable parts. Refer servicing to qualified technicians only.
4
Order code: 41533
Infinity B401 Beam
IMPORTANT:
The manufacturer will not accept liability for any resulting damages caused by the non-observance of
this manual or any unauthorized modification to the device.
● Never let the power cord come into contact with other cables! Handle the power cord and all
connections with the mains with particular caution!
● Never modify, bend, mechanically strain, put pressure on, pull or heat up the power cord.
● Never remove warning or informative labels from the unit.
● Never use anything to cover the ground contact.
● Never lift the fixture holding it by the projector-head, as the mechanics may be damaged. Always
hold the fixture by the transport handles.
● Never place any material over the lens.
● Never look directly into the light source.
● Never use the device without the lamp.
● Never ignite the lamp if the lens or any housing cover is open. Discharge lamps emit high ultraviolet
radiation, which can cause eye and skin damage.
● Never leave any cables lying around.
● Never use the device during thunderstorms, unplug the device immediately.
● Never leave various parts of the packaging (plastic bags, polystyrene foam, nails, etc.) within
children’s reach, as they are potential sources of danger.
● Do not aim the effect light at people or animals.
● Do not insert objects into air vents.
● Do not connect this device to a dimmer pack.
● Do not switch the device on and off in short intervals, as this will reduce the lamp’s life.
● If the lamp has been turned OFF, let the lamp cool down for 15 minutes before turning the lamp ON
again.
● Do not touch the device’s housing bare-handed during its operation (housing becomes hot). Allow
the fixture to cool for at least 5 minutes before handling.
● Do not shake the device. Avoid brute force when installing or operating the device.
● Do not install lamps of higher wattage.
● Only use the device indoors, avoid contact with water or other liquids.
● Only operate the fixture after having checked if the housing is firmly closed and all screws are tightly
fastened.
● Only operate the device after having familiarized with its functions.
● Avoid flames and do not put close to flammable liquids or gases.
● Always allow a free air space of at least 80 cm around the unit for ventilation.
● Always disconnect power from the mains, when device is not used or before cleaning! Only handle
the power cord holding it by the plug. Never pull out the plug by tugging the power cord.
● Make sure that the device is not exposed to extreme heat, moisture or dust.
● Make sure that the available voltage is not higher than stated on the rear panel.
● Make sure that the power cord is never crimped or damaged. Check the device and the power
cord from time to time.
● Make sure that the core diameter of extension cords and power cords is sufficient for the required
power consumption of the device.
● If the lens is obviously damaged, it has to be replaced. Cracks and scratches impair its functioning.
● If device was dropped or struck, disconnect mains power supply immediately. Have a qualified
engineer inspect for safety before operating.
● If the device has been exposed to drastic temperature fluctuation (e.g. after transportation), do not
switch it on immediately. The arising condensation water might damage your device. Leave the
device switched off until it has reached room temperature.
● If your Infinity device fails to work properly, discontinue the use immediately. Pack the unit securely
(preferably in the original packing material), and return it to your Infinity dealer for service.
● For adult use only. Moving head must be installed beyond the reach of children. Never leave the unit
running unattended.
● Never attempt to bypass the thermostatic switch or fuses.
● For replacement use fuses of same type and rating only.
● Let the lamp cool down for 20 minutes, before replacing the lamp.
● A hot discharge lamp is under high pressure and can therefore spontaneously explode. The risk
increases with the age, temperature and improper handling of the lamp.
5
Order code: 41533
Infinity B401 Beam
● If the lamp breaks, special safety precautions must be taken as mercury is released. Evacuate the
area immediately and ventilate it.
● The user is responsible for correct positioning and operating of the Infinity. The manufacturer will not
accept liability for damages caused by the misuse or incorrect installation of this device.
● This device falls under protection class I. Therefore it is essential to connect the yellow/green
conductor to earth.
● Repairs, servicing and electric connection must be carried out by a qualified technician.
● WARRANTY: Till one year after date of purchase.
Operating Determinations
● This device is not designed for permanent operation. Consistent operation breaks will ensure that the
device will serve you for a long time without defects.
● The minimum distance between the light output and the illuminated surface must be bigger than
12 m.
● In order to eliminate wear and improve the device’s lifespan during periods of non-use, completely
disconnect from power source via breaker or by unplugging.
● The maximum ambient temperature ta = 40 °C must never be exceeded.
● The relative humidity must not exceed 50 % with an ambient temperature of 40 °C.
● If this device is operated in any other way than the one described in this manual, the product may
suffer damages and the warranty becomes void.
● Any other operation may lead to dangers like short-circuit, burns, electric shock, crash etc.
You endanger your own safety and the safety of others!
Rigging
Please follow the European and national guidelines concerning rigging, trussing and all
other safety issues.
Do not attempt the installation yourself!
Always have the inspections carried out by an authorized dealer!
Procedure:
● If the Infinity is lowered from the ceiling or high joists, professional trussing systems have to be used.
● Use a clamp to mount the Infinity with the mounting brackets to the trussing system.
● The Infinity must never be fixed swinging freely in the room.
● The installation must always be secured with a safety attachment, e.g. an appropriate safety net or
safety cable.
● When rigging, derigging or servicing the Infinity, always make sure, that the area below the
installation site is secured and that there are not any unauthorized people around.
6
Order code: 41533
Infinity B401 Beam
The Infinity can be placed on a flat stage floor or mounted to any kind of truss with mounting brackets
and a clamp.
Improper installation can cause serious injuries and/or damage of property!
Connection with the Mains
Connect the device to the mains with the power-plug.
Always check if the right color cable is connected to the right place.
International
EU Cable
UK Cable
US Cable
Pin
L
BROWN
RED
YELLOW/COPPER
PHASE
N
BLUE
BLACK
SILVER
NEUTRAL
YELLOW/GREEN
GREEN
GREEN
PROTECTIVE GROUND
Make sure that the device is always properly connected to the earth!
Improper installation can cause serious injuries and/or damage of property!
7
Order code: 41533
Infinity B401 Beam
Return Procedure
Returned merchandise must be sent prepaid and in the original packing, call tags will not be issued.
Package must be clearly labeled with a Return Authorization Number (RMA number). Products returned
without an RMA number will be refused. Highlite will not accept the returned goods or any responsibility.
Call Highlite 0031-455667723 or mail aftersales@highlite.com and request an RMA prior to shipping the
fixture. Be prepared to provide the model number, serial number and a brief description of the cause for
the return. Be sure to properly pack fixture, any shipping damage resulting from inadequate packaging is
the customer’s responsibility. Highlite reserves the right to use its own discretion to repair or replace
product(s). As a suggestion, proper UPS packing or double-boxing is always a safe method to use.
Note: If you are given an RMA number, please include the following information on a piece of paper
inside the box:
01) Your name
02) Your address
03) Your phone number
04) A brief description of the symptoms
Claims
The client has the obligation to check the delivered goods immediately upon delivery for any short-
comings and/or visible defects, or perform this check after our announcement that the goods are at their
disposal. Damage incurred in shipping is the responsibility of the shipper; therefore the damage must be
reported to the carrier upon receipt of merchandise.
It is the customer's responsibility to notify and submit claims with the shipper in the event that a fixture is
damaged due to shipping. Transportation damage has to be reported to us within one day after receipt
of the delivery.
Any return shipment has to be made post-paid at all times. Return shipments must be accompanied with
a letter defining the reason for return shipment. Non-prepaid return shipments will be refused, unless
otherwise agreed in writing.
Complaints against us must be made known in writing or by fax within 10 working days after receipt of the
invoice. After this period complaints will not be handled anymore.
Complaints will only then be considered if the client has so far complied with all parts of the agreement,
regardless of the agreement of which the obligation is resulting.
8
Order code: 41533
Infinity B401 Beam
Description of the Device
Features
The Infinity B401 Beam is a moving head with high output and great effects.
Output
● Beam angle: 4°
● Light source: Osram Sirius HRI 230 W (7R)
● Lamp socket: E20.6
● Color temperature: 7600 K
● Output: 9500 lm
Electrical
● Input voltage: 100-240 V AC, 50/60Hz
● Power consumption: 402 W
Control
● Onboard: battery-powered, full color display including gravity sensor
● Battery lifetime: max 30 days (full charge)
● Control modes: Manual, Auto, DMX-512
● Control protocol: DMX, W-DMX, sACN, Art-Net, RDM
● DMX channels: Basic (18 channels), Advance (23 channels), User (up to 23 channels)
● Wireless DMX: Wireless Solution Sweden
Optical System
● Dimmer: 0-100 %, mechanical
● Shutter: 0-20 Hz
● Focus: motorized
● Prisms: 5-facet linear and 16-facet circular
● Frost filter: Yes
Movement
● Pan: 540°
● Tilt: 270°
● Pan/Tilt resolution: 16 bit
● Special: Blackout during Pan/Tilt movement, color and gobo change; User-selectable Pan and Tilt
ranges; Reverse Pan/Tilt movement
Gobos and Colors
● Static gobo wheel: 17 metal gobos + open
● Gobo functions: Gobo flow effect, Gobo shake
● Color wheel: 14 dichroic filters + white
● Color functions: Bump colors, Split colors, Rainbow flow effect
Physical
● Color: Black
● Housing: Metal and flame-retardant plastic
● Data connection: 5-pin DMX IN/OUT, 2 x RJ45 connectors
● Power connection: PowerCON True1 IN/OUT
● IP rating: IP20
● Fuse: 7 A Fast Blow/250 V
● Dimensions: 519 x 380 x 284 mm (L x W x H)
● Weight: 21 kg
9
Order code: 41533
Infinity B401 Beam
Certification and Safety
● Certification: CE
● Max. ambient temperature: 40 °C
Optional accessories:
81014 – Showtec Sirius HRI 230 W, 8000 K
70454 – Safety cable Saveking 4 mm (Natural)
70456 – Safety cable Saveking 4 mm (Black)
75101 – Fast Coupler 150 kg (Black)
D7268 – Flightcase for 2 pcs Furion B401
FLA43 – DMX Terminator
Front View
Fig. 01
01) Lens
02) Antenna
03) Menu control
04) Touch display
05) Pan lock pin
06) Tilt lock pin
10
Order code: 41533
Infinity B401 Beam
Back View
Fig. 02
07) 5-pin DMX signal connector IN
08) RJ45 Ethernet connector
09) PowerCON True1 power connector IN
10) Fuse 7 A Fast Blow/250 V
11) PowerCON True1 power connector OUT
12) Ground/earth connection
13) RJ45 Ethernet connector
14) 5-pin DMX signal connector OUT
Installation
Remove all packing materials from the Infinity B401 Beam. Check if all foam and plastic padding is
removed. Connect all cables.
Do not supply power before the whole system is set up and connected properly.
Always disconnect from electric mains power supply before cleaning or servicing.
Damages caused by non-observance are not subject to warranty.
11
Order code: 41533
Infinity B401 Beam
Installing the Lamp
The Infinity B401 Beam is equipped with an Osram Sirius HRI 230 W (7R) discharge lamp (order code
81014).
Note that product versions with other lamps may be offered in the future. Check your product
specification label for information.
Lamp installation must be carried out by a qualified technician.
A hot discharge lamp is under high pressure and can therefore spontaneously explode. The risk increases
with the age, temperature and improper handling of the lamp.
If the lamp breaks, special safety precautions must be taken as mercury is released. Evacuate the area
immediately and ventilate it.
The lamp has to be replaced when it is damaged or deformed due to the heat.
Always disconnect from electric mains power supply before changing lamps.
Do not install lamps with a higher wattage! Lamps with a higher wattage generate temperatures the
device was not designed for.
Damages caused by non-observance are not subject to warranty.
Always read the safety instructions that are included with the lamp.
Do not touch the bulb with bare hands. Oil on hands shortens the lamp life. If you touch the bulb glass,
wipe off the glass with a clean lint-free cloth and rubbing alcohol.
Read all safety warnings at the beginning of this manual, before replacing the lamp!!!
Let the lamp cool down for 20 minutes, before replacing the lamp.
Procedure:
01) Turn off the lamp and let it cool down for at least 5 minutes.
02) Turn off the Infinity and disconnect it from the mains. Let it cool down for 20 minutes.
03) Turn the moving head with the fan facing downwards.
04) Loosen the 4 Phillips-head quarter-turn fasteners on the housing and remove the cover (Fig. 03).
05) Disconnect the 2 wires from the lamp terminals (Fig. 04).
06) Push the lamp carefully to the left against the 2 springs on the left side (Fig. 04).
Fig. 03
Fig. 04
12
Order code: 41533
Infinity B401 Beam
07) Roll the lamp carefully out of the fixture and remove it (Fig. 05 and Fig 06).
Fig. 05
Fig. 06
08) Take the new lamp holding it by the base. Before installing the new lamp, read the instructions
included with the lamp.
Do not touch the bulb glass with bare hands. Oil on hands shortens the lamp life. If you touch the bulb
glass, wipe off the glass with a clean lint-free cloth and rubbing alcohol.
09) Carefully slide the lamp under the 2 springs in its place.
10) Connect the 2 wires to the lamp terminals.
11) Replace the cover and tighten the 4 Phillips-head quarter-turn fasteners on the housing.
After a new lamp is installed, it is recommended to reset the lamp operating hours counter. See 3.4 Lamp
Settings on page 36. You can view total operating hours of the lamp (Lamp on Time) in the Fixture
Information submenu (see page 41).
13
Order code: 41533
Infinity B401 Beam
Lamp Adjustment
The lamp position is set in the factory. As lamps differ from manufacturer to manufacturer, it may be
necessary to readjust their position. If the hotspot is not in the center of the projection of the light beam, it
can be calibrated on a horizontal plane (wall).
Lamp adjustment must be carried out by a qualified technician.
01) Turn the moving head with the fan facing upwards.
02) Loosen the 4 Phillips-head quarter-turn fasteners on the housing and remove the cover (Fig. 07).
03) Using a flat-head screwdriver turn the adjustment screw clockwise to move the hotspot to the left
and counterclockwise to move it to the right (Fig. 08).
Fig. 07
Fig. 08
04) Replace the cover and fasten the 4 Phillips-head quarter-turn fasteners on the housing.
14
Order code: 41533
Infinity B401 Beam
Lock/Unlock the Moving Head
You can lock/unlock the moving head by sliding the lock pins:
● Slide the pan lock pin (05) to the left to disable and to the right to enable the horizontal movement
(Pan) of the fixture (see Fig. 09).
● Slide the tilt lock pin (06) upwards to disable and downwards to enable the vertical movement (Tilt)
of the fixture (see Fig. 09).
Always lock the moving head before transportation!
Make sure to release the lock pins before operating the fixture.
Fig. 09
15
Order code: 41533
Infinity B401 Beam
Setup and Operation
Follow the directions below, as they pertain to your preferred operation mode.
Before plugging the unit in, always make sure that the power supply matches the product specification
voltage. Do not attempt to operate a 120 V specification product on 230 V power, or vice versa.
Connect the device to the main power supply.
Control Modes
There are 5 modes:
● Stand-alone (auto programs)
● Manual
● DMX-512 (18 CH, 23 CH)
● W-DMX (18 CH, 23 CH)
● Art-Net/sACN (18 CH, 23 CH)
One Infinity (Stand-alone/Auto programs)
01) Fasten the effect light to a firm trussing. Leave at least 0,8 meter on all sides for air circulation.
02) Always use a safety cable (order code 70454/70456).
03) Plug the end of the electric mains power cord into a proper electric power supply socket.
04) When the Infinity is not connected with a DMX or Ethernet cable, it functions as a stand-alone
device.
05) Please see 5. Stand-Alone on page 40 for more information.
One Infinity (Manual)
01) Fasten the effect light to a firm trussing. Leave at least 0,8 meter on all sides for air circulation.
02) Always use a safety cable (order code 70454/70456).
03) Plug the end of the electric mains power cord into a proper electric power supply socket.
04) When the Infinity is not connected with a DMX or Ethernet cable, it functions as a stand-alone
device.
05) Please see 4. Manual Control on page 39 for more information.
16
Order code: 41533
Infinity B401 Beam
Multiple Infinitys (DMX control)
01) Fasten the effect light to a firm trussing. Leave at least 0,8 meter on all sides for air circulation.
02) Always use a safety cable (order code 70454/70456).
03) Use a 5-pin DMX cable to connect the Infinity and other devices.
04) Link the units as shown in Fig. 10. Connect the first unit's DMX "out" socket with the second unit's "in"
socket, using a DMX signal cable. Repeat this process to link the rest of the units.
05) Supply electric power: Plug electric mains power cords into each unit's PowerCON True1 socket,
then plug the other end of the mains power cord into proper electric power supply sockets, starting
with the first unit. Do not supply power before the whole system is set up and connected properly.
Fig. 10
Note : Link all cables before connecting electric power
17
Order code: 41533
Infinity B401 Beam
Multiple Infinitys (Wireless DMX Control)
01) Install multiple Infinitys at the desired positions (maximum distance to transceiver: 250 m).
02) Set the antennas (02) on the Infinitys in open position.
03) In order for the Infinitys to receive a wireless DMX signal properly, activate W-DMX on all Infinitys (see
3. Settings Menu on pages 32-33 for more information).
04) Pair the wireless signal transmitter with multiple Infinitys. In order to create a wireless connection,
please read the manual of your wireless signal transmitter.
05) When the W-DMX indicator on the display is blinking, the device is searching for a connection.
06) Once a connection has been established, the W-DMX indicator will stop blinking and will light up
green.
07) Use a DMX cable to connect the transmitter to a suitable light controller.
Fig. 11
18
Order code: 41533
Infinity B401 Beam
Sweden 2.4 GHz Wireless communication module
Communication distance:
Depending on the transmitting power or transmitter module
Test conditions:
W-DMX TRx Transmitter module, 2 dBi Antenna, transmitting power
20 dBm (100 mW)
Range indoor:
60 m (approx. through three concrete walls)
Range outdoor:
250 m
Wireless DMX Connection
The wireless receiving module “Nano G5 Receiver, 2.4 GHz”, provided by the Swedish WIRELESS
SOLUTION, only has a 2.4 GHz wireless signal receiving function. In order to match the wireless signal,
please use the 50175 W-DMX MicroBox F-1 G5 Transceiver by WIRELESS SOLUTION.
Wireless Problems:
01) No connection with a transmitter.
The W-DMX indicator on the display will be gray.
02) Searching for a connection.
The W-DMX indicator on the display will be blinking quickly.
When the wireless DMX communication is normal, the W-DMX indicator on the display is always
green.
The Infinity cannot receive a wireless DMX signal and a DMX cable signal at the same time.
Connect the Infinity to the Wireless DMX Signal Transmitter
Enable W-DMX for the device and select the W-DMX option as control mode. See 3. Settings Menu on
pages 32-33 and 2. Control Mode on page 31 for more information.
The Infinity cannot actively match a random wireless signal transmitter.
In order to create a wireless match, please check the manual of your wireless signal transmitter.
We advise you to use the W-DMX MicroBox F-1 G5 Transceiver (50175) by WIRELESS SOLUTION (Fig. 12).
Fig. 12
Disconnect the Infinity from the Wireless DMX Signal Transmitter
To turn off W-DMX, disable W-DMX by unlinking the fixture. See 3. Settings Menu on pages 32-33 for more
information. The Infinity will now be disconnected.
19
Order code: 41533
Infinity B401 Beam
Multiple Infinitys (Art-Net/sACN Control/RDM)
01) Fasten the effect light to a firm trussing. Leave at least 0,8 meter on all sides for air circulation.
02) Always use a safety cable (order code 70454/70456).
03) Use a CAT-5/CAT-6 cable to connect the Infinity and other devices.
04) Connect your computer with installed Art-Net software to the first device’s RJ45 "in" socket.
05) Link the units as shown in Fig. 13. Connect the first unit's RJ45 "out" socket with the second unit's "in"
socket, using a CAT-5/CAT-6 cable. Repeat this process to link the rest of the units.
06) Supply electric power: Plug electric mains power cords into each unit's PowerCON True1 socket,
then plug the other end of the mains power cord into proper electric power supply sockets, starting
with the first unit. Do not supply power before the whole system is set up and connected properly.
Fig. 13
Note : Link all cables before connecting electric power
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
/
