Little GIANT 587010 Dimensions Guide

Little GIANT
Brand
Little GIANT
Model
587010
Type
Dimensions Guide

Little GIANT 587010

The Little GIANT 587010 is a magnetic drive pump designed for in-line, non-submersible use. It features a leak-proof, seal-less magnetic drive and is constructed of glass-filled Ryton® for excellent chemical resistance. The ceramic shaft and thrust washers are 99.5% pure alumina for excellent wear and trouble-free service. The pump head is easily rotated, cleaned, or serviced, and the spindle shaft is supported at both ends to prevent impeller damage during start-up and stop of the pump.

The 587010 has a 3/4 HP motor and can pump up to 53 GPM at a 1-foot head.

Little GIANT 587010

The Little GIANT 587010 is a magnetic drive pump designed for in-line, non-submersible use. It features a leak-proof, seal-less magnetic drive and is constructed of glass-filled Ryton® for excellent chemical resistance. The ceramic shaft and thrust washers are 99.5% pure alumina for excellent wear and trouble-free service. The pump head is easily rotated, cleaned, or serviced, and the spindle shaft is supported at both ends to prevent impeller damage during start-up and stop of the pump.

The 587010 has a 3/4 HP motor and can pump up to 53 GPM at a 1-foot head.

Features
n Thermally protected, totally enclosed, fan
cooled, capacitor start motor
n Ball bearings
n Conduit box (must be field wired —
cord not included)
n Specific gravity to 1.1
n Fluid temperature to 200°F
n Ambient air temperature to 77°F
n Run-dry capability up to 8 hours
NOTE: Consult your local distributor or the
factory for applications with higher ambient
temperatures, specific gravities and viscosities.
Construction
n Volute — Glass-filled Ryton
®
n Housing — Glass-filled Ryton
®
n Impeller — Glass-filled Ryton
®
w/carbon bushing
n Shaft — Ceramic
n Thrust Washers — Ceramic
n O-Ring — Viton
®
The Little Giant MD-HC series features leakproof, seal-less magnetic drives and are designed for in-line, non-submersible
use. Volute, magnet housing and impeller are glass-filled Ryton
®
for excellent chemical resistance. Ceramic shaft
and thrust washers are 99.5% pure alumina for excellent wear and trouble-free service. Pumping heads are easily
rotated, cleaned or serviced. Spindle shaft is supported at both ends to prevent impeller damage during start-up and
stop of pump.
Magnetic Drive
TE-7-MD-HC
Form 995786 — 03/2003www.LittleGiantPump.com
TE-7-MD-HC
NOTE: Designs and dimensions may vary for various reasons (i.e. type of motor). This information should be used as
general guide rather than an unqualified guarantee. Specifications are subject to change without prior notice.
Replacement Parts
ITEM PART NO. DESCRIPTION
A 187005 Volute
B 187085 Thrust washer
C 187056 Shaft
D 187172 Impeller/Bushing
E 924016 O-ring
F 187023 Backplate
1 903712 Bolt
2 921050 Washer
3 187121 Drive magnet
4 187073 Magnet housing
NOTE: Parts A–F contact fluid
Specifications
Model
No.
Item
No.
Intake
Size
Discharge
Size Listing(s) HP Volts Hertz Amps Watts
Performance (GPM @ Head) Shut Off
Power
Cord (ft.)
Weight
(lbs.)1' 10' 25' 40' 50' Feet PSI
TE-7-MD-HC 587010 1-1/2" FNPT 1" MNPT UR/C-CSA 3/4 115 50/60 10.4/11.8 1080/1230 53 46.7 40 30.8 21.6 58.9 25.5 N/A 40.00
230 50/60 5.2/5.9 1080/1230
TE-7-MD-HC 587040 1-1/2" FNPT 1" MNPT UR/C-CSA 3/4 230 50/60 2.4/2.9 1080/1230 53 46.7 40 30.8 21.6 58.9 25.5 N/A 40.00
3 Phase 460 50/60 1.2/1.45 1080/1230
TE-7-MD-HC 587103 1-1/2" FNPT 1" MNPT Pump Head Less Motor 8.00
PO Box 12010 • Oklahoma City, OK 73157
Phone: 800.701.7894 • Fax: 800.701.8046
E-mail: [email protected]
  • Page 1 1
  • Page 2 2

Little GIANT 587010 Dimensions Guide

Little GIANT
Brand
Little GIANT
Model
587010
Type
Dimensions Guide

Little GIANT 587010

The Little GIANT 587010 is a magnetic drive pump designed for in-line, non-submersible use. It features a leak-proof, seal-less magnetic drive and is constructed of glass-filled Ryton® for excellent chemical resistance. The ceramic shaft and thrust washers are 99.5% pure alumina for excellent wear and trouble-free service. The pump head is easily rotated, cleaned, or serviced, and the spindle shaft is supported at both ends to prevent impeller damage during start-up and stop of the pump.

The 587010 has a 3/4 HP motor and can pump up to 53 GPM at a 1-foot head.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents