Denon AVR 1603 - AV Receiver Operating instructions

Brand: Denon

Model: AVR 1603 - AV Receiver

Category: Receiver

Type: Operating instructions

Page is loading ...

NOTE ON USE / HINWEISE ZUM GEBRAUCH

OBSERVATIONS RELATIVES A L’UTILISATION / NOTE SULL’USO

NOTAS SOBRE EL USO / ALVORENS TE GEBRUIKEN / OBSERVERA

• Avoid high temperatures.

Allow for sufficient heat dispersion

when installed on a rack.

• Vermeiden Sie hohe Temperaturen.

Beachten Sie, daß eine ausreichend

Luftzirkulation gewährleistet wird, wenn

das Gerät auf ein Regal gestellt wird.

• Eviter des températures élevées

Tenir compte d’une dispersion de

chaleur suffisante lors de l’installation

sur une étagère.

• Evitate di esporre l’unità a temperature

alte.

Assicuratevi che ci sia un’adeguata

dispersione del calore quando installate

l’unità in un mobile per componenti

audio.

• Evite altas temperaturas

Permite la suficiente dispersión del calor

cuando está instalado en la consola.

• Vermijd hoge temperaturen.

Zorg voor een degelijk hitteafvoer indien

het apparaat op een rek wordt geplaatst.

• Undvik höga temperaturer.

Se till att det finns möjlighet till god

värmeavledning vid montering i ett rack.

• Handle the power cord carefully.

Hold the plug when unplugging the

cord.

• Gehen Sie vorsichtig mit dem Netzkabel

um.

Halten Sie das Kabel am Stecker, wenn

Sie den Stecker herausziehen.

• Manipuler le cordon d’alimentation avec

précaution.

Tenir la prise lors du débranchement du

cordon.

• Manneggiate il filo di alimentazione con

cura.

Agite per la spina quando scollegate il

cavo dalla presa.

• Maneje el cordón de energía con

cuidado.

Sostenga el enchufe cuando

desconecte el cordón de energía.

• Hanteer het netsnoer voorzichtig.

Houd het snoer bij de stekker vast

wanneer deze moet worden aan- of

losgekoppeld.

• Hantera nätkabeln varsamt.

Håll i kabeln när den kopplas från el-

uttaget.

• Keep the set free from moisture, water,

and dust.

• Halten Sie das Gerät von Feuchtigkeit,

Wasser und Staub fern.

• Protéger l’appareil contre l’humidité,

l’eau et lapoussière.

• Tenete l’unità lontana dall’umidità,

dall’acqua e dalla polvere.

• Mantenga el equipo libre de humedad,

agua y polvo.

• Laat geen vochtigheid, water of stof in

het apparaat binnendringen.

• Utsätt inte apparaten för fukt, vatten

och damm.

• Unplug the power cord when not using

the set for long periods of time.

• Wenn das Gerät eine längere Zeit nicht

verwendet werden soll, trennen Sie das

Netzkabel vom Netzstecker.

• Débrancher le cordon d’alimentation

lorsque l’appareil n’est pas utilisé

pendant de longues périodes.

• Disinnestate il filo di alimentazione

quando avete l’intenzione di non usare il

filo di alimentazione per un lungo

periodo di tempo.

• Desconecte el cordón de energía

cuando no utilice el equipo por mucho

tiempo.

• Neem altijd het netsnoer uit het

stopkontakt wanneer het apparaat

gedurende een lange periode niet wordt

gebruikt.

• Koppla ur nätkabeln om apparaten inte

kommer att användas i lång tid.

• Do not obstruct the ventilation holes.

• Die Belüftungsöffnungen dürfen nicht

verdeckt werden.

• Ne pas obstruer les trous d’aération.

• Non coprite i fori di ventilazione.

• No obstruya los orificios de ventilación.

• De ventilatieopeningen mogen niet

worden beblokkeerd.

• Täpp inte till ventilationsöppningarna.

* (For sets with ventilation holes)

• Do not let foreign objects in the set.

• Keine fremden Gegenstände in das

Gerät kommen lassen.

• Ne pas laisser des objets étrangers dans

l’appareil.

• E’ importante che nessun oggetto è

inserito all’interno dell’unità.

• No deje objetos extraños dentro del

equipo.

• Laat geen vreemde voorwerpen in dit

apparaat vallen.

• Se till att främmande föremål inte

tränger in i apparaten.

• Do not let insecticides, benzene, and

thinner come in contact with the set.

• Lassen Sie das Gerät nicht mit

Insektiziden, Benzin oder

Verdünnungsmitteln in Berührung

kommen.

• Ne pas mettre en contact des

insecticides, du benzène et un diluant

avec l’appareil.

• Assicuratevvi che l’unità non venga in

contatto con insetticidi, benzolo o

solventi.

• No permita el contacto de insecticidas,

gasolina y diluyentes con el equipo.

• Laat geen insektenverdelgende

middelen, benzine of verfverdunner met

dit apparaat in kontakt komen.

• Se till att inte insektsmedel på

spraybruk, bensen och thinner kommer i

kontakt med apparatens hölje.

• Never disassemble or modify the set in

any way.

• Versuchen Sie niemals das Gerät

auseinander zu nehmen oder auf

jegliche Art zu verändern.

• Ne jamais démonter ou modifier

l’appareil d’une manière ou d’une autre.

• Non smontate mai, nè modificate l’unità

in nessun modo.

• Nunca desarme o modifique el equipo

de ninguna manera.

• Nooit dit apparaat demonteren of op

andere wijze modifiëren.

• Ta inte isär apparaten och försök inte

bygga om den.

ENGLISH DEUTSCH FRANCAIS ITALIANO ESPAÑOL NEDERLANDS SVENSKA

The lightning flash with arrowhead symbol, within an equilateral

triangle, is intended to alert the user to the presence of uninsulated

“dangerous voltage” within the product’s enclosure that may be of

sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert

the user to the presence of important operating and maintenance

(servicing) instructions in the literature accompanying the appliance.

WARNING:

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT

EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION:

TO REDUCE THE RISK OF ELECTRIC

SHOCK, DO NOT REMOVE COVER (OR

BACK). NO USER-SERVICEABLE PARTS

INSIDE. REFER SERVICING TO QUALIFIED

SERVICE PERSONNEL.

• DECLARATION OF CONFORMITY

We declare under our sole responsibility that this

product, to which this declaration relates, is in

conformity with the following standards:

EN60065, EN55013, EN55020, EN61000-3-2 and

EN61000-3-3.

Following the provisions of 73/23/EEC, 89/336/EEC and

93/68/EEC Directive.

• ÜBEREINSTIMMUNGSERKLÄRUNG

Wir erklären unter unserer Verantwortung, daß dieses

Produkt, auf das sich diese Erklärung bezieht, den

folgenden Standards entspricht:

EN60065, EN55013, EN55020, EN61000-3-2 und

EN61000-3-3.

Entspricht den Verordnungen der Direktive 73/23/EEC,

89/336/EEC und 93/68/EEC.

• DECLARATION DE CONFORMITE

Nous déclarons sous notre seule responsabilité que

l’appareil, auquel se réfère cette déclaration, est

conforme aux standards suivants:

EN60065, EN55013, EN55020, EN61000-3-2 et

EN61000-3-3.

D’après les dispositions de la Directive 73/23/EEC,

89/336/EEC et 93/68/EEC.

• DICHIARAZIONE DI CONFORMITÀ

Dichiariamo con piena responsabilità che questo

prodotto, al quale la nostra dichiarazione si riferisce, è

conforme alle seguenti normative:

EN60065, EN55013, EN55020, EN61000-3-2 e

EN61000-3-3.

In conformità con le condizioni delle direttive 73/23/EEC,

89/336/EEC e 93/68/EEC.

QUESTO PRODOTTO E’ CONFORME

AL D.M. 28/08/95 N. 548

• DECLARACIÓN DE CONFORMIDAD

Declaramos bajo nuestra exclusiva responsabilidad que

este producto al que hace referencia esta declaración,

está conforme con los siguientes estándares:

EN60065, EN55013, EN55020, EN61000-3-2 y

EN61000-3-3.

Siguiendo las provisiones de las Directivas 73/23/EEC,

89/336/EEC y 93/68/EEC.

• EENVORMIGHEIDSVERKLARING

Wij verklaren uitsluitend op onze verantwoordelijkheid

dat dit produkt, waarop deze verklaring betrekking

heeft, in overeenstemming is met de volgende normen:

EN60065, EN55013, EN55020, EN61000-3-2 en

EN61000-3-3.

Volgens de bepalingen van de Richtlijnen 73/23/EEC,

89/336/EEC en 93/68/EEC.

• ÖVERENSSTÄMMELSESINTYG

Härmed intygas helt på eget ansvar att denna produkt,

vilken detta intyg avser, uppfyller följande standarder:

EN60065, EN55013, EN55020, EN61000-3-2 och

EN61000-3-3.

Enligt stadgarna i direktiv 73/23/EEC, 89/336/EEC och

93/68/EEC.

CAUTION

• The ventilation should not be impeded by covering the ventilation openings with items, such as newspapers, table-cloths,

curtains, etc.

• No naked flame sources, such as lighted candles, should be placed on the apparatus.

• Please be care the environmental aspects of battery disposal.

• The apparatus shall not be exposed to dripping or splashing for use.

• No objects filled with liquids, such as vases, shall be placed on the apparatus.

ENGLISH

2 We greatly appreciate your purchase of the AVR-1603.

2 To be sure you take maximum advantage of all the features AVR-1603 has to offer, read these

instructions carefully and use the set properly. Be sure to keep this manual for future reference

should any questions or problems arise.

“SERIAL NO.

PLEASE RECORD UNIT SERIAL NUMBER ATTACHED TO THE REAR OF

THE CABINET FOR FUTURE REFERENCE”

2 INTRODUCTION

Thank you for choosing the DENON A/V Surround receiver. This remarkable component has been engineered to

provide superb surround sound listening with home theater sources such as DVD, as well as providing outstanding

high fidelity reproduction of your favorite music sources.

As this product is provided with an immense array of features, we recommend that before you begin hookup and

operation that you review the contents of this manual before proceeding.

TABLE OF CONTENTS

2 ACCESSORIES

Check that the following parts are included in addition to the main unit:

er t y

Before Using .......................................................3

Cautions on Installation .......................................3

Cautions on Handling ..........................................3

Features ..............................................................3

Part Names and Functions ..................................4

Read this First .....................................................5

Setting up the Speaker Systems.........................5

Connections..................................................5 ~ 8

Using the Remote Control Unit...........................9

⁄0

Setting up the system ................................9 ~ 12

⁄1

Remote Control Unit.................................13 ~ 15

⁄2

Operation ..................................................15 ~ 18

⁄3

Surround ...................................................18 ~ 20

⁄4

DSP Surround Simulation .........................21 ~ 23

⁄

Listening to the Radio...............................23 ~ 26

⁄6

Last Function Memory ......................................26

⁄7

Initialization of the Microprocessor ...................26

⁄8

Additional Information .................................27, 28

⁄9

Troubleshooting ................................................28

¤0

Specifications ....................................................29

List of Preset Codes.....................................192 ~ 194

q Operating instructions……………………………1

w Service station list ………………………………1

e Remote control unit (RC-920) …………………1

r R6P/AA batteries ………………………………2

t AM loop antenna …………………………………1

y FM indoor antenna ………………………………1

BEFORE USING

Pay attention to the following before using this unit:

• Moving the set

To prevent short circuits or damaged wires in the

connection cords, always unplug the power cord and

disconnect the connection cords between all other

audio components when moving the set.

• Before turning the power operation switch on

Check once again that all connections are proper and

that there are not problems with the connection cords.

Always set the power operation switch to the

standby position before connecting and disconnecting

connection cords.

• Store this instructions in a safe place.

After reading, store this instructions along with the

warranty in a safe place.

• Note that the illustrations in this instructions may

differ from the actual set for explanation purposes.

• V. AUX terminal

The AVR-1603's front

panel is equipped with a

V. AUX terminal. Remove

the cap covering the

terminal when you want

to use it.

Noise or disturbance of the picture may be generated

if this unit or any other electronic equipment using

microprocessors is used near a tuner or TV.

If this happens, take the following steps:

• Install this unit as far as possible from the tuner or

TV.

• Set the antenna wires from the tuner or TV away from

this unit’s power cord and input/output connection

cords.

• Noise or disturbance tends to occur particularly when

using indoor antennas or 300 Ω/ohms feeder wires.

We recommend using outdoor antennas and 75

Ω/ohms coaxial cables.

For heat dispersal, leave at least 10 cm of space

between the top, back and sides of this unit and the

wall or other components.

• Switching the input function when input jacks are

not connected

A clicking noise may be produced if the input function

is switched when nothing is connected to the input

jacks. If this happens, either turn down the MASTER

VOLUME control or connect components to the input

jacks.

• Muting of PRE OUT jack, HEADPHONE jack and

SPEAKER terminals

The PRE OUT jack, HEADPHONE jack and

SPEAKER terminals include a muting circuit.

Because of this, the output signals are greatly

reduced for several seconds after the power

operation switch is turned on or input function,

surround mode or any other set-up is changed.

If the volume is turned up during this time, the output

will be very high after the muting circuit stops

functioning. Always wait until the muting circuit turns

off before adjusting the volume.

• Whenever the power operation switch is in the

£ OFF or STANDBY state, the apparatus is still

connected on some AC line voltages.

Please be sure to unplug the cord when you leave

home for, say, a vacation.

1. Dolby Pro Logic II decoder

Dolby Pro Logic II is a new format for playing

multichannel audio signals that offers

improvements over conventional Dolby Pro Logic.

It can be used to decode not only sources recorded

in Dolby Surround but also regular stereo sources

into five channels (front left/right, center and

surround left/right). In addition, various parameters

can be set according to the type of source and the

contents, so you can adjust the sound field with

greater precision.

2. Dolby Digital decoder

Dolby Digital, a digital discrete system in which the

different channels are completely independent,

recreates “three-dimensional” sound fields (sounds

with a sense of distance, movement and position)

with no crosstalk between channels for greater

reality. In addition, the 5 channels (excluding the 0.1

channel for low frequency effects) have a playback

range extending to 20 kHz, the same as the range

of CDs, thus resulting in clearer, more richly

expressive sound.

3. DTS (Digital Theater Systems) decoder

DTS provides up to 5.1 channels of wide-range, high

fidelity surround sound, from sources such as laser

disc, DVD and specially-encoded music discs.

4. High performance DSP simulates 7 sound fields

Playback is possible in 7 surround modes: 5-channel

Stereo, Mono Movie, Rock Arena, Jazz Club, Video

Game, Matrix and Virtual. You can enjoy a variety of

sound effects for different movie scenes and

program sources even with stereo sources not in

Dolby Surround.

5. Personal Memory Plus function

Personal Memory Plus is an advanced version of

Personal Memory. With Personal Memory Plus, the

set automatically memorizes the surround mode,

channel volume, surround parameters, etc., for each

of the separate input sources.

6. Remote control unit with pre-memory function

This unit comes with a remote control unit equipped

with a pre-memory function. The remote control

command codes for DENON remote controllable AV

components as well as for LD players, video decks,

TVs, etc., of other major manufacturers are prestored

in the memory.

7. EXT. IN jack

This unit is equipped with EXT. IN jacks for use with

audio formats of the future.

CAUTIONS ON INSTALLATION

CAUTIONS ON HANDLING

FEATURES

10 cm or more

wall

ENGLISH

PART NAMES AND FUNCTIONS

Front Panel

• For details on the functions of these parts, refer to the pages given in parentheses ( ).

q w te ur

y i!3!0

@0@1

@2@3@4@5

@7@8@9

!1 !2 !4 !5 !6o

!7!9 !8#0

Power operation switch ......................(10, 15, 23)

Headphones jack (PHONES) ...........................(17)

INPUT MODE button ..........................(16, 17, 19)

SPEAKER A/B buttons ..............................(15, 26)

TONE DEFEAT button.....................................(17)

ANALOG button ........................................(16, 17)

DOLBY/DTS SURROUND button..............(18. 19)

5CH STEREO button .......................................(20)

DIRECT/STEREO button .................................(20)

TUNING UP/DOWN buttons ...........................(24)

RDS button................................................(25, 26)

V. AUX terminals ...........................................(3, 7)

SURROUND MODE button.......................(16, 22)

SURROUND PARAMETER button ............(19, 22)

SELECT knob ....................................(16 ~ 19, 22)

TONE CONTROL button .................................(16)

CH VOL button................................................(18)

MASTER VOLUME control .............................(16)

RT button ........................................................(26)

PTY button ......................................................(25)

Master volume indicator (VOLUME LEVEL)....(16)

Display

Preset station select buttons..................(23 ~ 26)

BAND button...................................................(24)

EXT. IN button...........................................(16, 17)

SIGNAL indicators ...........................................(16)

INPUT mode indicators ...................................(16)

Remote control sensor (REMOTE SENSOR) ....(9)

Power operation indicator (ON/STANDBY)

INPUT SELECTOR knob .......(16, 18, 19, 24 ~ 26)

Remote control unit

• For details on the functions of these parts, refer to the pages given in parentheses ( ).

LED (indicator).................(13, 15)

SURROUND

button..................(16, 18, 19, 21)

Test tone button ...................(18)

Input source selector buttons

............(13 ~16, 18, 19, 24 ~ 26)

Remote control signal

transmitter ..............................(9)

POWER buttons ...........(13 ~ 15)

Master volume control

buttons..................................(16)

MUTING button ....................(17)

Tuner system/

buttons .............(13, 14, 24 ~ 26)

SURROUND PARAMETER

button .....................(14, 19 ~ 22)

Mode select

switches ...................(9, 13 ~ 15)

SYSTEM SETUP/

SETUP button .............(9, 12, 14)

STATUS/DISPLAY button

..(14, 17)

Cursor buttons

...................(9 ~ 12, 14, 18 ~ 22)

DIMMER button....................(17)

CH SELECT (channel select)/

ENTER button ..............(9, 14, 18)

VIDEO SELECT button..........(17)

SPEAKER select button ........(15)

RETURN button ....................(14)

INPUT MODE select

buttons......................(16, 17, 19)

System buttons...............(13, 14)

NOTE:

• The shaded buttons do not function with

the AVR-1603. (Nothing happens when they are

pressed.)

INTPUTOUTPUT

LRL

Step 3 (page 9 to 12)

Finally, setting up the system.

Step 2 (page 9)

Next, insert the batteries into the remote control unit.

ENGLISH

2 Speaker system layout

Basic system layout

• The following is an example of the basic layout for a system consisting of six speaker systems and a television

monitor:

Subwoofer

Center speaker system

Front speaker systems

Set these at the sides of the TV or

screen with their front surfaces as

flush with the front of the screen as

possible.

Surround speaker systems

READ THIS FIRST

This A / V surround Receiver must be setup before use. Following these steps.

Step 1 (page 5 to 8)

Choose the location to setup the speakers and connecting the components.

SETTING UP THE SPEAKER SYSTEMS

•

Do not plug in the power cord until all connections

have been completed.

•

Be sure to connect the left and right channels

properly (left with left, right with right).

•

Insert the plugs securely. Incomplete connections

will result in the generation of noise.

•

Use the AC OUTLET for audio equipment only. Do

not use them for hair driers, etc.

• Note that binding pin plug cords together with power

cords or placing them near a power transformer

will result in generating hum or other noise.

• Noise or humming may be generated if a connected

audio equipment is used independently without

turning the power of this unit on. If this happens,

turn on the power of this unit.

Connecting the audio components (1)

Decoders with 6-channel

analog outputs, etc.

Connecting a tape deck

Connections for recording:

Connect the tape deck’s recording input jacks (LINE IN or REC) to this unit’s tape

recording (OUT) jacks using pin plug cords.

Connections for playback:

Connect the tape deck’s playback output jacks (LINE OUT or PB) to this unit’s tape

playback (IN) jacks using pin plug cords.

CONNECTIONS

Tape deck or CD recorder

AC 230 V, 50 Hz

AC CORD

Connecting the AC OUTLET

AC OUTLET

• SWITCHED (capacity – 100 W)

The power to these outlets is turned on and off in conjunction with the POWER

switch on the main unit, and when the power is switched between on and standby

from the remote control unit.

No power is supplied from these outlets when this unit’s power is at standby. Never

connect equipment whose capacity is above 100 W.

NOTE:

Only use the AC OUTLET for audio equipment. Never use them for hair driers, TVs or

other electrical appliances.

• Analog recording of signals input to the AVR-1603 in digital format is not possible. To record in analog, also

connect the analog signals of the player to the AVR-1603’s analog input terminals.

• The AVR-1603’s OPTICAL OUT terminal is an optical digital output terminal for connection of a CD

recorder, MD recorder or other digital recording device. Use it for digital recording.

AUDIO IN

AUDIO OUT

FRONT

SUBWOOFER

CENTER

SURROUND

AUDIO OUT

OPTICALCOAXIAL

DIGITAL AUDIODIGITAL AUDIO

OUTPUT

OPTICAL

DIGITAL AUDIODIGITAL AUDIO

AUDIO OUT

OUTPUT

DIGITAL OUT

DIGITAL IN

OUTPUT

INPUT

ENGLISH

ROUT

VIDEO

OUT

AUDIO

OUT

DIGITAL

ROUT

VIDEO

OPTICAL

OUT

AUDIO

OUT

DIGITAL

R OUT IN

AUDIO

VIDEO

OUT IN

LRL

OPT.-1

VIDEO

OPTICAL

Connecting the video equipments

TV or DBS tuner

DVD player or video disc player (VDP)

Monitor TV

MONITOR OUT

• Connect the TV’s video input

jack (VIDEO INPUT) to the

MONITOR OUT jack

using a 75 Ω/ohms video

coaxial pin plug cord.

VIDEO

NOTE:

Connection of the video disc Player Equipped with Dolby

Digital RF (AC-3RF) Output Jack.

• Please use a commercially available adaptor when

connecting the Dolby Digital RF (AC-3RF) output jack of

the video disc player to the digital input jack.

Please refer to the instruction manual of the adapter

when making connections.

Connecting a DVD player or a video disc player VDP

• Connect the DVD player’s (video disc player’s) video output jack (VIDEO

OUTPUT) to the (yellow) DVD/VDP IN jack using a 75 Ω/ohms

video coaxial pin plug cord.

• Connect the DVD player’s (video disc player’s) analog audio output jacks

(ANALOG AUDIO OUTPUT) to the DVD/VDP IN jacks using pin

plug cords.

• For better sound quality, we recommend using the DVD player with

digital rather than analog connections.

DVD players and VDP can also be connected to the VCR terminals.

AUDIO

VIDEO

Connecting a video decks

Connecting a TV/DBS tuner

TV/DBS

• Connect the TV’s or DBS tuner’s video output jack (VIDEO OUTPUT) to the

(yellow) TV/DBS IN jack using a 75 Ω/ohms video coaxial pin plug cord.

• Connect the TV’s or DBS tuner’s audio output jacks (AUDIO OUTPUT) to the

TV/DBS IN jacks using pin plug cords.

AUDIO

VIDEO

VIDEO OUT

AUDIO OUT

AUDIO IN

VIDEO IN

AUDIO OUT

VIDEO OUT

AUDIO OUT

DIGITAL OUT

Video input/output connections:

• Connect the video deck’s video output jack (VIDEO OUT) to the (yellow) VCR IN jack, and the video deck’s video input

jack (VIDEO IN) to the (yellow) VCR OUT jack using 75zΩ/ohms video coaxial pin plug cords.

Connecting the audio output jacks:

• Connect the video deck’s audio output jacks (AUDIO OUT) to the VCR IN jacks, and the video deck’s audio input jacks

(AUDIO IN) to the VCR OUT jacks using pin plug cords.

AUDIO

VIDEO

Video deck

VIDEO IN

CD player

Connecting a CD player

Connect the CD player’s analog output

jacks (ANALOG OUTPUT) to this unit’s CD

jacks using pin plug cords.

CD recorder, MD recorder or other component

equipped with digital input/output jacks

DIGITAL jacks

Use these for connections to audio equipment with digital output.

Refer to page 12 for instructions on setting this terminal.

• Use 75 Ω/ohms cable pin cords (sold separately) for coaxial

connections.

• Use optical cables (sold separately) for optical connections,

removing the cap before connecting.

CD player or other component

equipped with digital output

jacks

Connecting the audio components (2)

ENGLISH

To connect the video signal, connect using a 75 Ω/ohms video signal cable cord. Using an improper cable can

result in a drop in sound quality.

R VIDEO OUTOPTICALL

R VIDEO OUTL

OUTPUT

LINE OUT

DIGITAL OUT

VIDEO OUT

LINE OUT

Connecting a Video game equipment

• Connect the Video game equipment’s output jacks

to this unit’s V. AUX INPUT lacks.

Connecting a Video camera equipment

• Connect the Video camera equipment’s output

jacks to this unit’s V. AUX INPUT lacks.

Video camera

Video game

The V. AUX terminal is covered with a cap.

Remove this cap in order to use the terminal. (See

page 3 for instructions on removing the cap.)

Connecting a video component equipped with S-Video jacks

• When making connections, also refer to the operating instructions of the other components.

• A note on the S input jacks

The input selectors for the S inputs and pin jack inputs work in conjunction with each other.

• Precaution when using S-jacks

This unit’s S-jacks (input and output) and video pin jacks (input and output) have independent circuit structures, so that video

signals input from the S-jacks are only output from the S-jack outputs and video signals input from the pin jacks are only output

from the pin jack outputs.

When connecting this unit with equipment that is equipped with S-jacks, keep the above point in mind and make connections

according to the equipment’s instruction manuals.

S-VIDEO

OUT

S-VIDEO

OUT

S-VIDEO

OUT IN

S-VIDEO

VIDEO IN

VIDEO OUT

VIDEO IN

VIDEO OUT

DVD player, VDP, etc.

Connecting a monitor TV

Monitor TV

Connecting a TV/DBS tuner

•

Connect the TV’s or DBS tuner’s S video output jack

(S-VIDEO OUTPUT) to the TV/DBS IN jack

using an S jack connection cord.

S-VIDEO

TV or satellite broadcast tuner

Video deck

Connecting the video decks

• Connect the video deck’s S output jack (S-OUT) to the VCR IN

jack and the video deck’s S input jack (S-IN) to the VCR OUT

jack using S jack connection cords.

S-VIDEO

Connecting a DVD player or video disc player (VDP)

DVD/VDP

• Connect the DVD player’s or video disc player’s S-

Video output jack to the S-VIDEO DVD/VDP IN jack

using an S-Video connection cord.

MONITOR OUT

• Connect the TV’s or DBS tuner's S video

input (S-VIDEO INPUT) to the

MONITOR OUT jack using a S jack

connection cord.

S-VIDEO

Connecting the antenna terminals

DIRECTION OF

BROADCASTING

STATION

FM ANTENNA

75 Ω/ohms

COAXIAL

CABLE

FM INDOOR ANTENNA

(An Accessory)

AM LOOP

ANTENNA

(An Accessory)

AM OUTDOOR

ANTENNA

GROUND

NOTES:

•Do not connect two FM antennas simultaneously.

•Even if an external AM antenna is used, do not

disconnect the AM loop antenna.

•Make sure AM loop antenna lead terminals do

not touch metal parts of the panel.

Connection of AM antennas

1. Push the lever.

2. Insert the

conductor.

3. Return the lever.

AM loop antenna assembly

Connect to the AM

antenna terminals.

Bend in the reverse

direction.

Remove the vinyl tie

and take out the

connection line.

a. With the antenna

on top any stable

surface.

b. With the antenna

attached to a wall.

Installation hole Mount on wall, etc.

Mount

ENGLISH

Speaker system connections

• Connect the speaker terminals with the speakers

making sure that like polarities are matched (< with

<, > with >). Mismatching of polarities will result

in weak central sound, unclear orientation of the

various instruments, and the sense of direction of the

stereo being impaired.

• When making connections, take care that none of

the individual conductors of the speaker cord come

in contact with adjacent terminals, with other speaker

cord conductors, or with the rear panel.

Speaker Impedance

• When speaker systems A and B are use separately,

speakers with an impedance of 6 to 16 Ω/ohms can

be connected for use as front speakers.

• Be careful when using two pairs of front speakers

(A + B) at the same time, since use of speakers with

an impedance of 12 to 16 Ω/ohms.

• Speakers with an impedance of 6 to 16 Ω/ohms can

be connected for use as center and surround speakers.

• The protector circuit may be activated if the set is

played for long periods of time at high volumes when

speakers with an impedance lower than the specified

impedance are connected.

1. Loosen by turning

counterclockwise.

2. Insert the cord.

3. Tighten by turning

clockwise.

NOTE:

NEVER touch the speaker terminals when the

power is on.

Doing so could result in electric shocks.

System B

FRONT SPEAKER SYSTEMS FRONT SPEAKER SYSTEMS

SURROUND SPEAKER SYSTEMS

• Precautions when connecting

speakers

If a speaker is placed near a TV or

video monitor, the colors on the

screen may be disturbed by the

speaker’s magnetism. If this should

happen, move the speaker away

to a position where it does not have

this effect.

Connection jack for subwoofer with

built-in amplifier (super woofer), etc.

To achieve Dolby Digital (AC-3)

playback effect, use a unit that can

sufficiently reproduce frequencies

of under 80 Hz.

Connecting the speaker cords

(

)(

)

(

) (

)(

) (

)

System A

CENTER SPEAKER

SYSTEM

Protector circuit

• This unit is equipped with a high-speed protection circuit. The purpose of this circuit is to protect the

speakers under circumstances such as when the output of the power amplifier is inadvertently short-

circuited and a large current flows, when the temperature surrounding the unit becomes unusually high,

or when the unit is used at high output over a long period which results in an extreme temperature rise.

When the protection circuit is activated, the speaker output is cut off and the power supply indicator

LED flashes. Should this occur, please follow these steps: be sure to switch off the power of this unit,

check whether there are any faults with the wiring of the speaker cables or input cables, and wait for

the unit to cool down if it is very hot. Improve the ventilation condition around the unit and switch the

power back on.

If the protection circuit is activated again even though there are no problems with the wiring or the

ventilation around the unit, switch off the power and contact a DENON service center.

Note on speaker impedance

• The protector circuit may be activated if the set is played for long periods of time at high volumes when

speakers with an impedance lower than the specified impedance (for example speakers with an impedance

of lower than 4 Ω/ohms) are connected. If the protector circuit is activated, the speaker output is cut off.

Turn off the set’s power, wait for the set to cool down, improve the ventilation around the set, then turn

the power back on.

ENGLISH

Following the procedure outlined below, insert the batteries before using the remote control unit.

Point the remote control unit at the remote control

sensor as shown on the diagram at the left.

NOTES:

• The remote control unit can be used from a straight

distance of approximately 7 meters, but this distance

will shorten or operation will become difficult if there

are obstacles between the remote control unit and

the remote control sensor, if the remote control

sensor is exposed to direct sunlight or other strong

light, or if operated from an angle.

• Neon signs or other devices emitting pulse-type noise

nearby may result in malfunction, so keep the set as

far away from such devices as possible.

Approx. 7 m

q Press as shown by the arrow

and slide off.

w Insert the R6P/AA batteries properly,

as shown on the diagram.

e Close the lid.

NOTES:

• Use only R6P/AA batteries for replacement.

• Be sure the polarities are correct. (See the illustration inside the battery compartment.)

• Remove the batteries if the remote control transmitter will not be used for an extended period of time.

• If batteries leak, dispose of them immediately. Avoid touching the leaked material or letting it come in contact

with clothing, etc. Clean the battery compartment thoroughly before installing new batteries.

• Have replacement batteries on hand so that the old batteries can be replaced as quickly as possible when the

time comes.

• Even if less than a year has passed, replace the batteries with new ones if the set does not operate even when

the remote control unit is operated nearby the set. (The included battery is only for verifying operation.

Replace it with a new battery as soon as possible.)

30°

USING THE REMOTE CONTROL UNIT

Range of operation of the remote control unit

Inserting the batteries

30°

SETTING UP THE SYSTEM

• Once all connections with other AV components have been completed as described in “CONNECTIONS” (see

pages 5 to 8), make the various settings described below on the display.

These settings are required to set up the listening room’s AV system centered around the this unit.

SYSTEM SETUP button

Press this to display the system setup on the display.

CURSOR buttons (•, ª, 0, 1)

Press this change what appears on the display.

ENTER button

Press this to switch the display.

Also use this button to complete the setting.

• System setup items and default values (set upon shipment from the factory)

Input the combination of speakers in your system and

their corresponding sizes (SMALL for regular speakers,

LARGE for full-size, full-range) to automatically set the

composition of the signals output from the speakers and

the frequency response.

Front Sp.

Center

Sp.

Surround Sp.

Subwoofer

Large Small Small Yes

System setup

Speaker

Configuration

This selects the subwoofer speaker for playing deep bass

signals.

This parameter is for optimizing the timing with which

the audio signals are produced from the speakers and

subwoofer according to the listening position.

Subwoofer

Mode

Delay Time

Default settings

Set the slide switch to “AUDIO”.

Use the following buttons to set up the system:

Subwoofer mode = Normal

Front & Subwoofer Center Surround L & R —

3.6 m 3.6 m 3.0 m —

NOTE:

• The system setup is not displayed when “HEADPHONE ONLY” is selected.

Digital

Inputs

Input

source

Digital In

Assignment

This assigns the digital input jacks for the

different input sources.

COAXIAL

OPTICAL-1 OPTICAL-2

DVD/VDP TV/DBS

Set the frequency (Hz) below which the bass sound of

the various speakers is to be output from the subwoofer.

Crossover

Frequency

80 Hz

Auto surround mode function setting.

Auto Surround

Mode

Auto Surround Mode = ON

Set the Ext. In Subwoofer channel playback level.

Ext. In SW

Level

Ext. In SW Level = +15 dB

Check that all the components are correct, then press the POWER operation

switch on the main unit to turn on the power.

Press the SYSTEM SETUP button to enter the setting.

Press the ENTER or (down) button to switch to the speaker

configuration set up.

NOTE:

Press the SYSTEM SETUP button again to finish system set up. System set up can be finished at any time. The

changes to the settings made up to that point are entered.

*SYSTEM SET UP

Before setting up the system

NOTE: Please make sure the “AUDIO” position of the slide switch on the

remote control unit.

(Main unit)

Use the (left) and (right) buttons to select your center speaker type.

Press the ENTER or (down) button to switch to the surround speaker setting.

2 CENTER SMALL

LARGE

SMALL

NONE

NOTE:

• When “Small” has been selected for the front speakers, “Large” cannot be selected for the center speaker.

Use the (left) and (right) buttons to select your surround speaker type.

Press the ENTER or (down) button to switch to the subwoofer setting.

3 SURR. SMALL

LARGE

SMALL

NONE

NOTE:

• When “Small” has been selected for the front speakers, “Large” cannot be selected for the surround speakers.

Setting the speaker configuration

Use the (left) and (right) buttons to select your front speaker type.

Press the ENTER or (down) button to switch to the center speaker setting.

1 FRONT LARGE

LARGE

SMALL

(right) button(left) button

(Initial)

ENGLISH

Use the (left) and (right) buttons to select your subwoofer setting.

Press the ENTER or (down) button to enter the settings and switch to the

SUBWOOFER MODE setting.

4 S.WOOFER YES

YES

• Parameters

Large…… Select this when using speakers that can fully reproduce low sounds of below 80 Hz.

Small…… Select this when using speakers that cannot reproduce low sounds of below 80 Hz with sufficient

volume. When this setting is selected, low frequencies of below 80 Hz are assigned to the subwoofer.

None…… Select this when no speakers are installed.

Yes/No…. Select “Yes” when a subwoofer is installed, “No” when it’s not installed.

NOTE:

Select “Large” or “Small” not according to the physical size of the speaker, but according to the bass reproduction

capacity at 80 Hz. If you cannot determine the best setting, try comparing the sound when set to “Small” and

when set to “Large”, at a level that will not damage the speakers.

Caution:

In case the subwoofer is not used, be sure to set “Subwoofer = No”, or the bass sound of front channel is divided

to subwoofer channel and not reproduced in some mode.

(right) button(left) button

(Initial)

Setting the Subwoofer mode and Crossover Frequency

Use the (left) and (right) buttons to select the Subwoofer mode.

Press the ENTER or (down) button to enter the setting and switch to the

Crossover Frequency setting.

5 SW MODE NORM

+MAIN NORM

(right) button(left) button

(Initial)

Use the (left) and (right) buttons to select the Crossover Frequency.

Press the ENTER or (down) button to enter the setting and switch to the

SPEAKER DISTANCE setting.

6 CR.OVER 80Hz

80Hz

100Hz

120Hz

(right) button(left) button

(Initial)

ENGLISH

NOTES:

— Assignment of low frequency signal range —

• The only signals produced from the subwoofer channel are LFE signals (during playback of Dolby Digital or

DTS signals) and the low frequency signal range of channels set to “SMALL” in the setup menu. The low

frequency signal range of channels set to “LARGE” are produced from those channels.

— Crossover Frequency —

• When “Subwoofer“ is set to “Yes“ at the “Speaker Configuration Setting“, set the frequency (Hz) below

which the bass sound of the various speakers is to be output from the subwoofer (the crossover frequency).

• For speakers aet to “Small“, sound with a frequency below the crossover frequency is cut, and the cut bass

sound is output from the subwoofer instead.

NOTE: For ordinary speaker systems, we recommend setting the crossover frequency to 80 Hz. When

using small speakers, however, setting the crossover frequency to high frequency may improve

frequency response for frequencies near the crossover frequency.

— Subwoofer mode —

• The subwoofer mode setting is only valid when “LARGE” is set for the front speakers and “YES” is set for

the subwoofer in the “Speaker Configuration” settings (see page 10).

If “SMALL” is set for the front speakers or “NO” is set for the subwoofer, the subwoofer mode setting does

not affect playback of low frequency signal range.

• When the “+MAIN” playback mode is selected, the low frequency signal range of channels set to “LARGE”

are produced simultaneously from those channels and the subwoofer channel.

In this playback mode, the low frequency range expand more uniformly through the room, but depending on

the size and shape of the room, interference may result in a decrease of the actual volume of the low frequency

range.

• When the “NORM” playback mode is selected, the low frequency signal range of channels set to “LARGE”

are only produced from those channels. In this playback mode there tends to be little interference of the low

frequency range in the room.

• Try playing the music or movie source and select the playback mode providing the stronger low frequency

range sound.

Input the distances from the listening position to the speakers and set the surround

delay time.

Preparations:

Measure the distances from the listening position to the speakers (L

1 to L3 on the

diagram at the right).

: Distance from center speaker to listening position

2: Distance from front speakers to listening position

3: Distance from surround speakers to listening position

CAUTION:

Set the center speaker at the same distance from the front speakers (left and right) or the subwoofer, or so

that the difference in distance (L

– L1) is 1.5 meters or less.

Set the surround speakers (left and right) at the same distance from the front speakers (left and right) or the

subwoofer, or so that the difference in distance (L

– L3) is 4.5 meters or less.

• The number changes in units of 0.1 meter each time one of the buttons is

pressed. Select the value closest to the measured distance.

(“/SW” appears only when subwoofer = yes.)

Press the ENTER or (down) button to switch to the center speaker setting.

7 FRNT/SW 3.6m

Listening

position

CenterFL FR

Setting the speaker distance

SL SR

Use the (left) and (right) buttons to set the distance from the front

speakers and subwoofer to the listening position.

NOTE:

• The speaker distance can be adjusted between 0 and 18 meters in steps of 0.1 meter.

Use the (left) and (right) buttons to set the distance from the center

speaker to the listening position.

Use the (left) and (right) buttons to set the distance from the surround

speakers to the listening position.

• The number changes in units of 0.1 meter each time one of the buttons is

pressed. Select the value closest to the measured distance.

Press the ENTER or (down) button to switch to the surround speakers

setting.

• The number changes in units of 0.1 meter each time one of the buttons is

pressed. Select the value closest to the measured distance.

Press the ENTER or (down) button to enter the setting and switch the

DIGITAL input (COAX) setting.

8 CENTER 3.6m

9 SURR. 3.0m

NOTE:

• No setting when “None” has been selected for the center speaker.

NOTE:

• No setting when “None” has been selected for the surround speakers.

ENGLISH

NOTE:

• TUNER and V. AUX cannot be selected.

• Select “OFF” if nothing is connected.

12 OPT2 TV

CD AUX DVD TV VCR CDR OFF

Use the (left) and (right) buttons to assign the input function connected

to the OPTICAL input 2 (OPT 2) terminal.

(right) button(left) button

Press the ENTER or (down) button to switch the auto surround mode

setting.

(Initial)

13 AUTOSURR. ON

OFF ON

For the three kinds of input signals as shown below, the surround mode played the last is stored in the

memory. At next time it the same signal inputs, the memorized surround mode is automatically selected and

the signal is played.

Note that the surround mode setting is also stored separately for the different input function.

SIGNAL Default Auto Surround Mode

q Analog and PCM 2-channel signals STEREO

w 2-channel signals of Dolby Digital, DTS or other multichannel format Dolby PLII Cinema

e Multichannel signals of Dolby Digital, DTS or other multichannel format Dolby or DTS Surround

Setting the Auto Surround Mode

Use the (left) and (right) buttons to select the Auto Surround mode.

(right) button(left) button

Press the ENTER or (down) button to switch the Ext. In SW Level setting.

(Initial)

14 EXT.IN SW +15

+00

+05

+10 +15

Set the method of playback of the analog input signal connected to the Ext. In terminal.

Setting the Ext. In SW Level

Use the (left) and (right) buttons to select the Ext. In Subwoofer channel

Level playback.

(right) button(left) button

Press the ENTER or (down) button if you want to start the settings over

from the beginning.

(Initial)

This completes the system setup operations. Once the system is set up, there is no need to make the settings

again unless other components or speakers are connected to or the speaker layout is changed.

After setting up the system

Press the SYSTEM SETUP button to finish system set up.

• Select “OFF” if nothing is connected.

Press the ENTER or (down) button to switch the OPTICAL input 2 (OPT 2)

setting.

10 COAX CD

CD AUX DVD TV VCR CDR OFF

11 OPT1 DVD

CD AUX DVD TV VCR CDR OFF

Input the type of components connected to the digital input terminals.

Setting the Digital In Assignment

Use the (left) and (right) buttons to assign the input function connected

to the COAXIAL input (COAXIAL) terminal.

Use the (left) and (right) buttons to assign the input function connected

to the OPTICAL input 1 (OPT 1) terminal.

(right) button(left) button

Press the ENTER or (down) button to switch the optical input 1 (OPT 1)

setting.

(right) button(left) button

• Select “OFF” if nothing is connected.

(Initial)

ENGLISH

REMOTE CONTROL UNIT

• Turn on the power of the different components before operating them.

Set mode switch 1 to “AUDIO”.

1. CD player (CD) and CD recorder and MD

recorder (CDR/MD) system buttons

2. Tape deck (TAPE) system buttons

6,7 : Manual search

(reverse and forward)

2 : Stop

1 : Play

8,9 : Auto search (Cue)

3 : Pause

DISC : Switch discs

SKIP+ (for CD changers only)

6 : Rewind

7 : Fast-forward

2 : Stop

1 : Forward play

0 : Reverse play

A/B : Switch between decks A and B

3. Tuner system buttons

SHIFT : Switch preset channel range

CHANNEL : Preset channel

+, – (up/down)

TUNING : Frequency

+, – (up/down)

BAND : Switch between the AM and FM bands

MODE : Switch between auto and mono

MEMORY : Preset memory

NOTE:

• TUNER can be operated when the switch is at “AUDIO” position.

Operating DENON audio components

Set mode switch 2 to the position for the

component to be operated. (CD, CDR/MD or

Tape deck)

Operate the audio component.

• For details, refer to the component’s operating instructions.

While this remote control is compatible with a wide range of infrared controlled components, some

models of components may not be operated with this remote control.

DENON and other makes of components can be operated by setting the preset memory.

This remote control unit can be used to operate components of other manufacturers without using the learning

function by registering the manufacturer of the component as shown on the List of Preset Codes (pages

192~194).

Operation is not possible for some models.

Set mode switch 1 to “AUDIO” or “VIDEO”.

Preset memory

Set the AUDIO side for the CD, Tape deck or

CDR/MD position, to the VIDEO side for the

DVD/VDP, DBS/CABLE, VCR or TV position.

Set mode switch 2 to the component to be

registered.

Press the ON/SOURCE button and the OFF

button at the same time.

• Indicator flash.

Referring to the included List of Preset Codes, use the number buttons to input the

preset code (a 3-digit number) for the manufacturer of the component whose signals

you want to store in the memory.

456

789

To store the codes of another component in the memory, repeat steps 1 to 4.

NOTES:

• The signals for the pressed buttons are emitted while setting the preset memory. To avoid accidental

operation, cover the remote control unit’s transmitting window while setting the preset memory.

• Depending on the model and year of manufacture, this function cannot be used for some models, even if

they are of makes listed on the included list of preset codes.

• Some manufacturers use more than one type of remote control code. Refer to the included list of preset

codes to change the number and check.

• The preset memory can be set for one component only among the following: CDR/MD, DVD/VDP

and DBS/CABLE.

The preset codes are as follows upon shipment from the factory and after resetting:

TV, VCR ..............................HITACHI

CD, TAPE ...........................DENON

CDR/MD.............................DENON (CDR)

DVD/VDP............................DENON (DVD)

DBS/CABLE........................ABC (CABLE)

ENGLISH

NOTE:

• Some manufacturers use different names for

the DVD remote control buttons, so also

refer to the instructions on remote control for

that component.

Set mode switch 1 to “AUDIO” or “VIDEO”.

Operating component stored in the preset memory

Set mode switch 2 to the component you want

to operate.

Set the AUDIO side for the CD, Tape deck or

CDR/MD position, to the VIDEO side for the

DVD/VDP, DBS/CABLE, VCR or TV position.

1. Digital video disc player (DVD, DVD SETUP) system buttons

Operate the component.

• For details, refer to the component’s operating instructions.

Some models cannot be operated with this remote control unit.

POWER : Power on/standby

(ON/SOURCE)

6,7 : Manual search

(forward and reverse)

2 : Stop

1 : Play

8,9 : Auto search

(to beginning of track)

3 : Pause

0 ~ 9, +10 : 10 key

skip + : Disc skip

(for DVD changer only)

DISPLAY : Switch display

MENU : Menu

RETURN : Return

SETUP : Setup

D, H, F, G : Cursor up, down, left and right

ENTER : Enter setting

2. Video disc player (VDP) system buttons

POWER : Power on/standby

(ON/SOURCE)

6,7 : Manual search

(forward and

reverse)

2 : Stop

1 : Play

8,9: Auto search (cue)

3 : Pause

0~9, +10 : 10 key

3. Video deck (VCR) system buttons

POWER : Power on/standby

(ON/SOURCE)

6,7 : Manual search

(forward and

reverse)

2 : Stop

1 :Play

3 : Pause

Channel +, –: Channels

4. Digital broadcast satellite (DBS) tuner and

cable (CABLE) system buttons

POWER : Power on/standby

(ON/SOURCE)

MENU : Menu

RETURN : Return

D, H, F, G : Cursor up, down,

left and right

ENTER : Enter

CHANNEL : Switch channels

+, –

0~9, +10 : Channels

DISPLAY : Switch display

VOL +, – : Volume up/down

5. Monitor TV (TV) system buttons

POWER : Power on/standby

(ON/SOURCE)

MENU : Menu

RETURN : Return

D, H, F, G : Cursor up, down,

left and right

ENTER : Enter

CHANNEL : Switch channels

+, –

0~9, +10 : Channels

DISPLAY : Switch display

TV/VCR : Switch between

TV and video

player

TV VOL : Volume up/down

+, –

NOTES:

• For this CD, CDR, MD and TAPE components, buttons can be operated in the same way as for Denon

audio components (page 13).

• The TV can be operated when the switch is at DVD/VDP, VCR, TV position.

Punch Through

ENGLISH

Preparations:

Check that all connections are proper.

Turn on the power.

Press the power operation switch (button).

1 2

OPERATION

Before operating

Select the front speakers.

Press the SPEAKER A or B button turn the speaker

on.

• ¢ ON/STANDBY

The power turns on and power indicator is lit.

Several seconds are required from the time

the power operation switch is set to the “¢

ON/STANDBY” position until sound is output.

This is due to the built-in muting circuit that

prevents noise when the power switch is turned

on and off.

Set the power operation switch to this position

to turn the power on and off from the included

remote control unit.

• £ OFF

The power turns off and power indicator is off.

In this position, the power cannot be turned on

and off from the remote control unit.

(Main unit) (Remote control unit)

(Main unit)

•“Punch Through” is a function allowing you to operate the PLAY, STOP, MANUAL SEARCH and AUTO

SEARCH buttons on the CD, TAPE, CDR/MD, DVD/VDP or VCR components when in the DBS/CABLE or TV

mode. By default, nothing is set.

Set mode switch 1 to “VIDEO”.

Set mode switch 2 to the component to be

registered (DBS/CABLE or TV).

Press the DVD/VDP power button and the TV

power button at the same time.

• Indicator flash.

Input the number of the

component you want to set.

(See Table 1)

456

789

Table 1

CD 1

TAPE 2

CDR/MD 3

DVD/VDP 4

VCR 5

No setting 0

No.

(Remote control unit)

• The front speaker A, B setting can be also be

changed with the SPEAKER button on the

remote control unit.

ENGLISH

Playing the input source

1 2 5

Select the input source to be played.

Example: CD

(Main unit) (Remote control unit)

Select the input mode.

• Selecting the analog mode

Press the ANALOG button to switch to the

analog input.

(Main unit) (Remote control unit)

• Selecting the external input (EXT. IN) mode

Press the EXT. IN (or the EXT. IN button on

the remote control unit) to switch the external

input.

(Main unit) (Remote control unit)

• Selecting the AUTO, PCM and DTS modes

The mode switches as shown below each time

the INPUT MODE button is pressed.

AUTO PCM DTS

(Main unit) (Remote control unit)

Input mode selection function

Different input modes can be selected for the different

input sources. The selected input modes for the

separate input sources are stored in the memory.

q AUTO (All auto mode)

In this mode, the types of signals being input to the

digital and analog input jacks for the selected input

source are detected and the program in the AVR-

1603’s surround decoder is selected automatically

Notes on playing a source encoded with DTS

• Noise may be generated at the beginning of

playback and while searching during DTS

playback in the AUTO mode. If so, play in the

DTS mode.

•

In some rare cases the noise may be generated

when you preform the operation to stop

playback of a DTS-CD or DTS-LD.

upon playback. This mode can be selected for all

input sources other than TUNER.

The presence or absence of digital signals is

detected, the signals input to the digital input jacks

are identified and decoding and playback are

performed automatically in DTS, Dolby Digital or

PCM (2 channel stereo) format. If no digital signal

is being input, the analog input jacks are selected.

Use this mode to play Dolby Digital signals.

w PCM (exclusive PCM signal playback mode)

Decoding and playback are only performed when

PCM signals are being input.

Note that noise may be generated when using this

mode to play signals other than PCM signals.

e DTS (exclusive DTS signal playback mode)

Decoding and playback are only performed when

DTS signals are being input.

r ANALOG (exclusive analog audio signal playback

mode)

The signals input to the analog input jacks are

decoded and played.

t EXT. IN (external decoder input jack selection mode)

The signals being input to the external decoder

input jacks are played without passing through the

surround circuitry.

NOTE:

• Note that noise will be output when CDs or LDs

recorded in DTS format are played in the “PCM”

(exclusive PCM signal playback) or “ANALOG”

(exclusive analog audio signal playback) mode.

Select the AUTO or DTS (exclusive DTS signal

playback) mode when playing signals recorded in

DTS from a laser disc player.

Select the play mode.

Press the SURROUND MODE button, then turn

the SELECT knob.

Example: Stereo

(Main unit) (Remote control unit)

To select the surround mode

while adjusting the surround

parameters, channel volume or

tone control, press the surround

mode button then operate the

selector. (See page 18.)

(Main unit)

Start playback on the selected component.

•

For operating instructions, refer to the component’s

manual.

Adjust the volume.

(Main unit) (Remote control unit)

The volume level is

displayed on the master

volume level display.

The volume can be adjusted within the range

of –70 to 0 to 18 dB, in steps of 1 dB. However,

when the channel level is set as described on

page 18, if the volume for any channel is set

at +1 dB or greater, the volume cannot be

adjusted up to 18 dB. (In this case the

maximum volume is adjusted to “18 dB —

(Maximum value of channel level)”.)

Input mode when playing DTS sources

• Noise will be output if DTS-compatible CDs or LDs

are played in the “ANALOG” or “PCM” mode.

When playing DTS-compatible sources, be sure to

connect the source component to the digital input

jacks (OPTICAL/COAXIAL) and set the input mode

to “DTS”.

Input mode display

ANALOGDIGITAL

DIGITAL

ANALOG

AUTO

PCM

DTS

INPUT

AUTO

PCM

DTS

INPUT

AUTO

PCM

DTS

INPUT

AUTO

PCM

DTS

INPUT

• In the AUTO mode

• In the DIGITAL PCM mode

• In the DIGITAL DTS mode

• In the ANALOG mode

One of these lights, depending

on the input signal.

Input signal display

SIGNAL

DIGITAL

SIGNAL

• DOLBY DIGITAL

• DTS

• PCM

The indicator lights when digital signals

are being input properly. If the indicator

does not light, check whether the digital input

component setup (page 12) and connections are

correct and whether the component’s power is

turned on.

DIGITAL

NOTE:

• The indicator will light when playing

CD-ROMs containing data other than audio signals,

but no sound will be heard.

DIGITAL

After starting playback

[1] Adjusting the sound quality (tone)

The tone switches as follows each time the TONE

CONTROL button is pressed.

BASS TREBLE

123

(Main unit)

Front panel display

• Descriptions of the unit’s operations

are also displayed on the front panel

display. In addition, the display can

be switched to check the unit’s

operating status while playing a

source by pressing the STATUS

button.

ENGLISH

With the name of the volume to

be adjusted selected, turn the

SELECT knob to adjust the level.

• To increase the bass or treble:

Turn the control clockwise.

(The bass or treble sound can

be increased to up to +12 dB in steps of 2 dB.)

•

To decrease the bass or treble: Turn the

control counterclockwise. (The bass or

treble sound

can be decreased to up to –12

dB in steps of 2 dB.)

If you do not want the bass and treble to be

adjusted, turn on the tone defeat mode.

The signals do not pass through the

bass and treble adjustment circuits,

providing higher quality sound.

(Main unit)

[2] Listening over headphones

NOTE:

To prevent hearing loss, do not raise the volume level

excessively when using headphones.

Plug the headphones’ plug into

the jack.

Connect the headphones to

the PHONES jack.

The pre-out output (including

the speaker output) is

automatically turned off

when headphones are

connected.

PHONES

[3] Turning the sound off temporarily (muting)

Use this to turn off the audio output

temporarily.

Press the MUTING button.

Cancelling MUTING mode.

Press the MUTING button again.

Muting will also be cancelled

when MASTER VOL is adjusted

up or down.

(Remote

control unit)

Simulcast playback

Use this switch to monitor a video

source other than the audio source.

Press the VIDEO SELECT button

repeatedly until the desired source

appears on the display.

Cancelling simulcast playback.

• Select “SOURCE” using the VIDEO SELECT

button.

• Switch the program source to the component

connected to the video input jacks.

[4]

Combining the currently playing sound with the desired image

(Remote

control unit)

[5] Checking the currently playing program source, etc.

(Remote

control unit)

Using the dimmer function

• Use this to change the brightness of

the display.

The display brightness changes in

four steps (bright, medium, dim and

off) by pressing the main unit’s

DIMMER button repeatedly.

(Remote

control unit)

BRIGHT MEDIUM

OFF

DIM

Playback using the external input (EXT. IN) jacks

Set the external input (EXT. IN) mode.

Press the EXT. IN button

to switch the external

input.

Once this is selected,

the input signals

connected to the FL (front left), FR (front right),

C (center), SL (surround left) and SR (surround

right) channels of the EXT. IN jacks are output

directly to the front (left and right), center,

surround (left and right) speaker systems

without passing through the surround circuitry.

In addition, the signal input to the SW (subwoofer)

jack is output to the PRE OUT SUBWOOFER jack.

Cancelling the external input mode

To cancel the external input (EXT. IN) setting,

press the INPUT MODE (AUTO, PCM, DTS) or

ANALOG button to switch to the desired input

mode. (See page 16.)

(Remote control unit)(Main unit)

• When the input mode is set to the external input

(EXT. IN), the play mode (DIRECT,STEREO,

DOLBY/DTS SURROUND, 5CH STEREO or DSP

SIMULATION) cannot be selected.

2 1

NOTES:

• In play modes other than the external input mode,

the signals connected to EXT. IN jacks cannot

be played. In addition, signals cannot be output

from channels not connected to the input jacks.

• The external input mode can be set for any input

source. To watch video while listening to sound,

select the input source to which the video signal

is connected, then set this mode.

(Remote

control unit)

(Main unit)

ENGLISH

Recording the program source (recording the source currently being monitored)

Follow step 1 to 3 under “Playing the input source”.

Start recording on the tape or video deck.

For instructions, refer to the component’s operating

instructions.

The signals of the source selected with the function selector button are output simultaneously to the

CDR/TAPE and VCR AUDIO OUT jacks. If a total of two tape and/or video decks are connected and set to

the recording mode, the same source can be recorded simultaneously on every decks.

Simultaneous recording

NOTES:

• The AUDIO IN’s signal selected with the function selector button are output to the CDR/TAPE and VCR

AUDIO OUT jacks.

• The DIGITAL IN’s signal selected with the function selector button are output to the DIGITAL OUT (OPTICAL)

jack.

SURROUND

Before playing with the surround function

• Before playing with the surround function, be sure to use the test tones to adjust the playback level from each

speakers. This adjustment can be performed from the remote control unit, as (described) below.

• The adjustment with the test tones is only effective in the DOLBY/DTS SURROUND modes.

The adjusted playback levels for the different surround modes are automatically stored in the memory of each

surround modes.

Set the DOLBY/DTS SURROUND (Dolby Pro

Logic II or Dolby Digital or DTS) modes.

(Main unit) (Remote control unit)

Press the TEST TONE button.

(Remote control unit)

Test tones are output from the

different speakers. Use the

channel volume adjust buttons

to adjust so that the volume of

the test tones is the same for

all the speakers.

NOTE: Please make sure the “AUDIO” position

of the slide switch on the remote control

unit.

(Remote control unit)

After completing the adjustment, press the

TEST TONE button again.

2, 3

(Remote control unit)

• After adjusting using the test tones, adjust the channel levels either according to the playback sources or to

suit your tastes, as (described) below.

Select the speaker whose level you want to

adjust.

The channel switches as shown below each time

the button is pressed.

FL CNTR FR SR SL

(Main unit) (Remote control unit)

NOTE: Please make sure the “AUDIO” position

of the slide switch on the remote control

unit.

Adjust the level of the selected speaker.

(Main unit) (Remote control unit)

2 1

Default setting of channel level is 0 dB.

The level of the selected speaker can be adjusted

within the range of +12 to –12 dB.

SW channel level can be turned off by decreasing

one step from -12 dB.

OFF ´ -12 dB ´ 12 dB

Only adjustable when

the channel is

selected with the CH

VOL buttons on the

main unit.

Dolby Surround Pro Logic

mode

Select the function to which the component you

want to play is connected.

5, 74, 61 2

4, 6

5, 7

(Main unit) (Remote control unit)

Example:

The Dolby Surround Pro

Logic II Cinema or Music

mode can be chosen

directly by pressing the

CINEMA or MUSIC

button on the remote

control unit during

playback in the Dolby

Surround Pro Logic II

mode.

ENGLISH

Light

Play a program source with the

mark.

• For operating instructions, refer to the manuals

of the respective components.

Select the Dolby Surround Pro Logic II mode.

(Main unit) (Remote control unit)

• The Dolby Pro Logic indicator lights.

Display

Select the surround parameter mode.

(Main unit) (Remote control unit)

Display

MODE cinema

To perform this operation from the remote

control unit, check that the mode selector

switch is set to “AUDIO”.

Select the optimum mode for the source.

(Main unit) (Remote control unit)

or or

MODE musicMODE cinemaMODE emulation

Set the surround parameters according to the

mode.

(Main unit) (Remote control unit)

• The mode switches as shown below each

time the button is pressed.

MODE EMULATION

CINEMA EQ

DEFAULT

MODE CINEMA

CINEMA EQ

DEFAULT

MODE MUSIC

PANORAMA

DIMENSION

CENTER WIDTH

DEFAULT

Set the various surround parameters.

OFF ON

or or

CINEMA EQ OFF

• CINEMA EQ setting

OFF ON

or or

PANORAMA OFF

• PANORAMA setting

0 3 6

or or

DIMENSION 3

• DIMENSION setting

CENTER WIDTH O

4 7

or or

• CENTER WIDTH setting

YES Y/N NO

or or

DEFAULT Y/N

• DEFAULT setting

Select “Yes” to reset to the factory defaults.

NOTE:

• When making parameter settings, the display will

return to the regular condition several seconds

after the last button was pressed and the setting

will be completed.

Surround parameters q

Pro Logic

II Mode:

The Cinema mode is for use with stereo television shows and all programs encoded in Dolby Surround.

The Music mode is recommended as the standard mode for autosound music systems (no video), and is

optional for A/V systems.

The Emulation mode offers the same robust surround processing as original Pro Logic in case the source

contents is not of optimum quality.

Select one of the modes (“Cinema”, “Music” or “Emulation”).

Panorama Control:

This mode extends the front stereo image to include the surround speakers for an exciting “wraparound”

effect with side wall imaging.

Select “OFF” or “ON”.

Dimension Control:

This control gradually adjust the soundfield either towards the front or towards the rear.

The control can be set in 7 steps from 0 to 6.

Center Width Control:

This control adjust the center image so it may be heard only from the center speaker; only from the left/right

speakers as a phontom image; or from all three front speakers to varying degrees.

The control can be set in 8 steps from 0 to 7.

Dolby Digital mode (only with digital input) and DTS Surround (only with digital input)

Select the input source.

(Main unit) (Remote control unit)

q Select an input source set to digital (COAXIAL/

OPTICAL) (see page 12).

Playback with a digital input

1 1 3

Example:

(Main unit) (Remote control unit)

w Set the input mode to “AUTO” or “DTS”.

Select the Dolby/DTS Surround mode.

(Main unit) (Remote control unit)

4, 5, 6, 7, 8

5, 6, 7, 8

Play a program source with the ,

mark.

• The Dolby Digital indicator

lights when playing Dolby

Digital sources.

DIGITAL

Light

• The DTS indicator lights when

playing DTS sources.

Light

Press the ENTER button to finish surround

parameter mode.

(Remote control unit)

ENGLISH

Set the surround parameter according to the source.

First, press the SURROUND PARAMETER button.

(Remote control unit)

NOTE: Please make sure the “AUDIO” position of the slide switch on the remote

control unit.

Use the (left) and (right) buttons to set the CINEMA EQ.

CINEMA EQ OFF

OFF

Press the SURROUND PARAMETER or (down) button to switch to the D.

COMP. setting.

NOTE: This parameter is not displayed during DTS playback.

(Remote control unit)

(right) button(left) button

(Initial)

Use the (left) and (right) buttons to set the D. COMP.

D.COMP. OFF

OFF LOW MID HI

Press the SURROUND PARAMETER or (down) button to switch to the

LFE setting.

(Remote control unit)

(right) button(left) button

(Initial)

Use the (left) and (right) buttons to set the LFE level.

LFE 0dB

• The level can be adjusted in units of 1 dB from –10 to 0 dB.

Set to the desired level according to the speaker systems being used and the

source to be played.

Press the SURROUND PARAMETER or (down) button to switch to the

default setting.

(Remote control unit)

To reset the settings to the factory defaults, use the (left) and (right) to

display “Yes”.

DEFAULT Y/N

YES

Y/N NO

Press the SURROUND PARAMETER or (down) button to switch to the

CINEMA EQ. setting.

(Remote control unit)

(right) button(left) button

Surround parameters w

CINEMA EQ. (Cinema Equalizer):

The Cinema EQ function gently decreases the level of the extreme high frequencies, compensating for

overly-bright sounding motion picture soundtracks. Select this function if the sound from the front speakers

is too bright.

This function only works in the Dolby Pro Logic, Dolby Digital and DTS Surround modes.

D.COMP. (Dynamic Range Compression):

Motion picture soundtracks have tremendous dynamic range (the contrast between very soft and very loud

sounds). For listening late at night, or whenever the maximum sound level is lower than usual, the Dynamic

Range Compression allows you to hear all of the sounds in the soundtrack (but with reduced dynamic range).

(This only works when playing program sources recorded in Dolby Digital.) Select one of the four parameters

(“OFF”, “LOW”, “MID” (middle) or “HI” (high)). Set to OFF for normal listening.

LFE (Low Frequency Effect):

Program source and adjustment range

1. Dolby Digital: –10 dB to 0 dB

2. DTS Surround: –10 dB to 0 dB

When Dolby Digital encoded software is played, it is recommended that the LFE LEVEL be set to

0 dB for correct Dolby Digital playback.

When DTS encoded movie software is played, it is recommended that the LFE LEVEL be set to

0 dB for correct DTS playback.

When DTS encoded music software is played, it is recommended that the LFE LEVEL be set to

-10 dB for correct DTS playback.

Press the ENTER button to finish surround parameter mode.

(Remote control unit)

ENGLISH

DSP SURROUND SIMULATION

• This unit is equipped with a high performance DSP (Digital Signal Processor) which uses digital signal processing

to synthetically recreate the sound field. One of 7 preset surround modes can be selected according to the

program source and the parameters can be adjusted according to the conditions in the listening room to achieve

a more realistic, powerful sound. These surround modes can also be used for program sources not recorded in

Dolby Surround Pro Logic or Dolby Digital.

Surround modes and their features

7 VIRTUAL

ROCK ARENA

JAZZ CLUB

VIDEO GAME

MONO MOVIE

(NOTE 1)

MATRIX

5CH STEREO

Select this mode to enjoy a virtual sound field, produced from the front 2-channel

speakers.

Use this mode to achieve the feeling of a live concert in an arena with reflected

sounds coming from all directions.

This mode creates the sound field of a live house with a low ceiling and hard walls.

This mode gives jazz a very vivid realism.

Use this to enjoy video game sources.

Select this when watching monaural movies for a greater sense of expansion.

Select this to emphasize the sense of expansion for music sources recorded in stereo.

Signals consisting of the difference component of the input signals (the component

that provides the sense of expansion) processed for delay are output from the surround

channel.

In this mode, the signals of the front left channel are output from the left surround

channel, the signals of the front right channel are output from the right surround

channel, and the same (in-phase) component of the left and right channels is output

from the center channel. This mode provides all speaker surround sound, but without

directional steering effects, and works with any stereo program source.

Depending on the program source being played, the effect may not be very noticeable.

In this case, try other surround modes, without worrying about their names, to create a sound field suited to

your tastes.

NOTE 1: When playing sources recorded in monaural, the sound will be one-sided if signals are only input to one

channel (left or right), so input signals to both channels. If you have a source component with only one

audio output (monophonic camcorder, etc.) obtain a “Y” adaptor cable to split the mono output to two

outputs, and connect to the L and R inputs.

NOTE:

DIRECT, STEREO and 5CH STEREO mode can be used when playing PCM signals with a sampling

frequency of 96 kHz (such as from DVD-Video discs that contain 24 bit, 96 kHz audio). If such signals are

input during playback in one of the other surround modes, the mode automatically switches to STEREO.

Personal Memory Plus

This set is equipped with a personal memorize function that automatically memorizes the surround modes

and input modes selected for the input different sources. When the input source is switched, the modes

set for that source last time it was used are automatically recalled.

The surround parameters, tone control settings and playback level balance for the different output

channels are memorized for each surround mode.

DSP surround simulation

• To operate the surround mode and surround parameters from the remote control unit.

Select the surround mode for the input channel.

(Remote control unit)

The surround mode switches in the following

order each time the DSP SIMULATION button is

pressed:

MONO MOVIE ROCK ARENA

JAZZ CLUBVIDEO GAME

MATRIX

To enter the surround parameter setting mode, press the SURROUND

PARAMETER button.

• The surround parameter switches in the following order each time the

SURROUND PARAMETER button is pressed for the different surround

modes.

(Remote control unit)

ROOM SIZE

EFFECT

DEFAULT

DELAY

DEFAULT

D. COMP.

LFE

DEFAULT

• ROCK ARENA

• JAZZ CLUB

• VIDEO GAME

• MONO MOVIE

• MATRIX • VIRTUAL

Use the (left) and (right) buttons to set the room size.

ROOM SIZE MED

LARGEMED-LMEDMED-SSMALL

(Remote control unit)

(right) button(left) button

Use the (left) and (right) buttons to set the effect level.

EFFECT LEVEL 10

15101

(Remote control unit)

(right) button(left) button

Display the parameter you want to adjust, then use the (left) and (right)

buttons to set it.

(1) ROOM SIZE

(Initial)

(2) EFFECT LEVEL

(Initial)

Page is loading ...

Denon AVR 1603 - AV Receiver Operating instructions

Brand: Denon

Model: AVR 1603 - AV Receiver

Category: Receiver

Type: Operating instructions

Download PDF

report

in other languages

español: Denon AVR 1603 - AV Receiver Instrucciones de operación

Denon AVR 1603 - AV Receiver Operating instructions

Denon AVR 1603 - AV Receiver Operating instructions

in other languages

Related papers

Other documents