Whirlpool IDL 71 EU.2 Owner's manual

Page is loading ...

Lavastoviglie 1

Istruzioni per l'installazione e l'uso

Dishwasher 11

Instructions for installation and use

Lave-vasseille 21

Instructions pour l'installation et l'emploi

Geschirrspuler 31

Informationen f

ü

r Installation und Gebrauch

Vaatwasser 41

Gebruiksaanwijzingen voor de plaatsing en gebruik

Lavavajillas 51

Instrucciones para la instalaci

ó

n y el uso

Máquina de lavar louça

61

Instruções para a instalação e o uso

IDL 71

Page is loading ...

GB

11

Safety, a good habit to get into

WARNING

Read the instructions contained in this manual carefully, as

they will provide you with important information on safety

when installing, using and servicing your appliance.

This dishwasher conforms to the following

European Community Directives:

- 73/23/CEE (Low Voltage Directive) and subsequent

amendments;

- 89/336/CEE (Electromagnetic Compatibility) and

subsequent amendments.

- 97/17/CE (Labelling)

1.Remove the packaging carefully and dispose of it.

2.After removing the packaging, check to make sure your

appliance is intact. If in doubt, contact a qualified professional.

3.This dishwasher must only be used by adults and for washing

household dishes.

4.Essential rules you should follow when using your appliance:

- do not touch the appliance with wet hands or feet or barefoot,

- we advise against the use of extension leads and multiple

plugs,

- during installation, the power supply wire must be completely

free of bends or large dangerous kinks,

- if the appliance is not operating properly or if maintenance

operations are necessary, disconnect the dishwasher from the

mains power supply.

Close-up view (control panel)

ON-OFF Button

ON-OFF Indicator light

Door handle

Cycle selection knob

Low salt indicator light

Low rinse aid indicator light

5.Keep children away from the dishwasher when it is open

and keep detergents out of their reach.

6.Your dishwasher is not to be installed outdoors, not even if

the area is covered by a roof, and it is extremely dangerous to

leave it exposed to rain and thunderstorms.

7.Do not touch the heating element during or straight after a

wash cycle.

8.Do not lean or sit on the door when it is open, as this could

overturn the dishwasher.

9.If the appliance malfunctions, turn off the water inlet tap

and disconnect the plug from the wall socket. Then try to consult

the chapter entitled “Is there a problem?” and if you can’t find

a solution there, then call for assistance.

10.Out of use appliances must be made inoperable, by cutting

the power supply wire and damaging the door lock.

Cycle phase and delayed start indicator lights

Delayed start select button

Half load selection button

Half-load button

Start/Reset Button

To guarantee the efficiency and safety of this appliance:

l only contact authorized technical assistance

service centres

l always ask that original spare parts be used

25

5

C

G

A

B

D

R

H

E

F

I

6

L

Start-Reset

7

12

GB

Close-up view (Inside)

Upper rack

Top sprayer arm

Rack height adjuster

Lower rack

Bottom sprayer arm

Salt container cap

Washing filter

Detergent and rinse aid dispenser

7HFKQLFDOFKDUDFWHULVWLFV

:LG WK FP 

'H SWK F P 

+HLJKW FP 

&DSDFLW\ VWDQGDUGSODFHVHWWLQJV

0DLQVZDWHUSUHVVXUH SVLSVL.3D·03D·EDU

3RZHUYROWDJH 6HHGDWDSODWH

7RWDODEVRUEHUSRZHU 6HHGDWDSODWH

)XVH 6HHGDWDSODWH

J

L

K

H

F

E

G

I

GB

13

Salt …

Salt

Water hardness varies according to where you live. If hard

water were to enter your dishwasher, scaly incrustations

would form on your dishes.

Thanks to a water softener which uses special dishwasher

salt, the limescale in the water is eliminated.

Loading salt into the water softener

Always use salt which is intended for dishwasher use.

The salt container is

situated underneath the

lower rack and should be

filled up as follows:

1.Pull out the lower rack

completely, unscrew and

remove the container cap.

2.If it is the first time you

load the salt container, fill

it up with water.

3.Put the funnel provided

on the hole and pour in

approximately two kilos of

salt. It is normal if some water comes out of the container.

4. Screw the cap back in place carefully.

The salt container should be filled up when the low

salt indicator light “E” flashes.

Once you have loaded the salt for the first time, it is normal

that the low salt indicator light stays on or flashes for about

5 consecutive cycles.

Warning:To prevent rust from forming, load the salt just

before beginning a wash cycle.

Adjusting the salt consumption

Your dishwasher can adjust its

salt consumption according to

the hardness of the water used

in order to optimise and

customise the dishwasher’s salt

consumption to the minimum

level necessary.

You can find out what the level

of water hardness in your area

is from the company that

supplies the water there.

To make the adjustment, follow

the instructions below:

1. unscrew the salt container cap

2. there is an arrow on the neck of the container (see figure

on the right); if necessary, turn the arrow anti-clockwise from

the “-” setting to the “+” setting according to the hardness

of the water supplied.

We recommend you make the adjustment according to the

following table:

Water Hardness

Clarke

degrees

°fH mmol/l

Selector

position

Salt

consu-

mption

(grams/-

cycle)

Autono-

my

(cycles\2-

kg)

0 - 14 0 - 17 0 -1,7 / 0 /

14 - 36 18 - 44 1,8 - 4,4 "-" 20 60

36 - 71 45 - 89 4,5 - 8,9 MED 40 40

>71 > 89 > 8,9 "+" 60 25

14

GB

Detergent and rinse aid ….

The detergent

Only use specific dishwasher detergents. The detergent

dispenser must be filled before each wash cycle begins

according to the instructions given in the “Wash cycle table”.

The detergent dispenser is situated on the inside of the

appliance door.

Loading the detergent

To open lid “A”, press button “B”. The detergent should be

poured into the two containers “C” and “D” up to the rim.

After pouring in the detergent, replace the lid, pressing down

until it clicks.

Dishwasher detergent in tabs is now available on the market,

in which case you should place one tab into container “D”

and replace the lid.

To make sure the lid shuts properly, remove any

detergent residue from the edges of the container

before closing it.

Rinse Aid

This product makes dishes sparkle more as it improves their

drying. The rinse aid container is situated on the inside of

the door: It should be filled up when the low rinse aid

indicator light "F" flashes.

Loading the rinse aid

To open the dispenser, turn cap “C” anticlockwise and take

care when you pour in the rinse aid to avoid it overflowing.

You can adjust the amount of rinse aid used by the dishwasher,

by using a screwdriver to regulate the dosage adjuster “F”

you will find under lid “C”. There are 6 possible settings; it is

normally set to 4.

Important:

Adjusting the rinse aid supply improves drying.

If drops of water remain on the dishes or spotting occurs,

turn the dosage adjuster to a higher setting. If, on the other

hand, the dishes have white streaks, then turn the dosage

adjuster down to a lower setting.

B

D

C

A

F

C

Warning

Three-in-one dishwasher tablets are now available on the market, and combine detergent, salt and rinse aid all in one.

If the water in your area is hard or very hard, we still recommend you pour extra salt into the relevant dispenser to prevent the

formation of white streaks on your dishes or on the interior of the appliance.

Using a three-in-one product means it is no longer necessary to put rinse aid into the relevant container.

If you want to achieve perfectly dry dishes, you may add rinse aid as long as the dosage adjuster is set to no.2.

In any case, please read the manufacturer's instructions on the packet.

If you use only these products, it is normal for the salt and rinse aid indicator lights to flash permanently after a certain number

of cycles.

GB

15

Before placing the dishes in the racks, remove the largest

scraps of food left over on your plates, you will thus avoid

blocking the filter, which would reduce the efficacy of the

wash.

If the saucepans and frying pans are very dirty, allow them

to soak before being washed.

You will thus avoid having to wash them again.

To make it easier to load your dishes, pull the racks out

fully.

How to use the lower rack

We recommend you place the most difficult dishes to wash

into the lower rack:

pans, lids, dinner plates and soup plates as illustrated in

the figure to the left.

Serving dishes and large lids should preferably be placed

on the sides of the rack, without for that matter obstructing

the rotation of the top sprayer arm.

- pans, salad bowls etc. must always be placed upside down

- very deep dishes should be placed obliquely, thus allowing

water to run down them freely.

-This basket is equipped with two removable grids: insert

the cutlery one by one into the slots; knives and utensils

with sharp blades or tips should be positioned with the sharp

parts at the bottom. Position all cutlery items so that they

don't touch.

If the rack has side baskets, the spoons should be loaded

individually into the appropriate slots (see fig. A-B).

- Especially long utensils should be placed in the horizon-

tal position at the front of the upper rack.

How to use the upper rack

Place delicate and lightweight dishes in the upper rack:

glasses, tea cups and coffee cups, saucers - but plates too

- shallow salad bowls, slightly dirty frying pans and shallow

pans (the photo illustrates a few examples).

Position lightweight dishes in such as way as to avoid their

being moved by the spray of water.

The upper rack can be equipped with one or two special

tip-up compartments for mugs and cups, as well as spoons,

knives and forks, which should be fitted in the slots

provided. Stemmed glasses can be hooked onto these

compartments by threading the stems into the slots

provided (see fig. D).

After loading the dishes, remember to check that the blades

on the sprayer arms can turn freely without knocking

against any dishes.

How to adjust the upper rack ….

The upper rack can be set in a high or low position. To do

so, open the rail stop flaps and pull the rack out completely;

now place it with the back wheels in high or low position,

then slide it along the guide rails until the front wheels

also go in; now close the rail stop flaps (see fig. F).

Loading the dishes

Upper rack

Load examples

1

2

3

4

Fig. F

Lower rack

B

A

fig. D

16

GB

How to start the dishwasher

How to start a wash cycle…

After performing all the operations described in the previous

chapters, turn the water tap on completely, press ON-OFF button

“A” situated on the control panel and indicator light “B” comes

on.

At this point, the dishwasher is on and ready to be programmed.

Starting and selecting the cycle.

Turn the cycle selector knob “D” clockwise until the reference notch

on the knob corresponds with the number or symbol for the cycle

you wish to set (consult the wash cycle table on page 17, especially

when first using the appliance).

If the appliance door is shut, press the Start button “R” and you will

hear a beep; the cycle will start up within a few seconds.

Cycle phase indicator lights

The dishwasher is provided with 4 indicator lights “G” which come

on in sequence as the appliance is performing that specific phase of

the wash cycle.

These phases are:

pre-wash, wash, rinses, drying

Cancelling or modifying a wash cycle in progress…..

Premise: You can cancel the wash cycle in progress, if it has only just

started.

To modify a wash cycle, keep the RESET button “R” pressed for

about 5 seconds: a prolonged beep will sound, followed by three

short beeps. Indicator light “G” will turn off and at this point, all

the settings will have been cancelled.

To select a new wash cycle, repeat the operations illustrated in the

paragraph entitled “starting and selecting the cycle”.

Warning: the knob must be turned clockwise from wash cycle 1 to

7, an anti-clockwise from wash cycle 7 to 1.

If you have left out a dish…

You can interrupt a wash cycle by pressing the ON- OFF button,

then place the dishes you had left out into the appliance, which will

start up from where it was interrupted when you turn it back on.

There’s been a power failure? Have you opened the

dishwasher door?

The wash cycle stops and then restarts when the electricity comes

back on or when the door is shut.

At the end of the wash cycle….

The end of the wash cycle is indicated by two short beeps and the

flashing of the drying phase indicator light.

Warning:when you open the dishwasher door after the wash cycle

has just ended or is under way, take care not to scald yourself with

the hot steam.

How to set the delayed start

When you have loaded the dishes, you can choose when to start

your dishwasher before setting the wash cycle desired. Press button

“H” to delay the start of the wash cycle by 12, 9, 6 or 3 hours. Each

time you press it, you will hear a short beep and the indicator light

“G” corresponding to the selected delay will light up.

Now you can select the desired wash cycle. Press the start button

“R” and after you hear the beep, the countdown to the delayed

start will begin.

Once this time is up, the indicator light will stop flashing and the

wash cycle will begin.

If you have set a 12 hour delay, for example, once you have selected

the wash cycle, the 12 hour indicator light will flash, followed by

the others in sequence until the set time delay is up. A quick look at

the indicator lights will keep you informed of the countdown progress

at all times.

Have you changed your mind?

If you change your mind, you can set a shorter time delay: press

button “H” to select it. You need not reset the wash cycle.

If on the other hand you want to cancel the delay set and you want

the cycle to start immediately, press button “H” repeatedly until the

cycle starts and indicator light “G” corresponding to the cycle start

phase comes on.

Dual function of indicator lights “G”

1) flashing to indicate a delayed start:to remind you that you

have set a delayed start;

2) on and not flashing beneath the cycle phase symbol:

meaning the cycle has started and is in the phase indicated by the

symbol.

You want to wash on one rack only?

Remember to use half the amount of detergent.

When you only have little cutlery to wash, you can run just half a

load on the upper rack, saving on water, detergent and electricity.

• When you press the “I” button, you will hear a blip and the “L”

indicator light will light up.

Once you have made your selection, start the wash cycle by pressing

Start and it will wash the top rack only.

- This option is available with all wash cycles.

- The Just You wash cycle is programmed to wash on the

upper rack only.

• Turn off the water tap.

• Wait a few minutes before unloading the dishes: if you wait a little

while they dry better thanks to the steam.

• Empty the lower rack first.

Warning:

Press button “A” to turn the appliance off, unplug the appliance

from the electricity socket to cut off the power supply; the power

supply cable should consequently be easily accessible.

Page is loading ...

18

GB

Tips to help you save

- It is important that you try to use the dishwasher with a full

load only in order to optimise consumption levels; in the

meantime use the soak cycle to avoid the formation of bad

odours and caked-on food.

- Select the most suitable wash cycle: the choice of wash

cycle depends on the type of dishes to wash and on how

dirty they are.

- Use the right amount of detergent: if you use too much,

you will not get cleaner dishes, but just more environmental

pollution.

- There is no need to rinse the dishes before placing them

inside the dishwasher.

How to keep your dishwasher in shape

After every wash

After every wash, turn off the water tap and leave the

dishwasher door ajar, so that moisture and bad odours are

not trapped inside.

Unplug the appliance

Before carrying out any cleaning or maintenance on the

dishwasher, always remove the plug from the electricity

socket: this way you will avoid the risk of any danger.

No solvent or abrasive cleaning products

Do not use solvents or abrasive cleaning products to clean

the exterior and rubber parts of your appliance. Use a cloth

dampened with lukewarm soapy water only.

To remove any stains from the surface of the appliance

interior, use a cloth dampened with water and a little white

vinegar or a cleaning product specifically made for

dishwashers.

If you are off on holiday

When you go on holiday, we recommend you run a cycle

with the dishwasher empty, then unplug it, turn off the water

inlet tap and leave the dishwasher door ajar: this will help

the seals last longer and prevent unpleasant odours from

forming inside the appliance.

If you are moving home

Should the appliance have to be moved, try to keep it in a

vertical position.; if absolutely necessary, it can be positioned

on its back.

The seals.

One of the factors that cause unpleasant odours to form

inside the dishwasher is food that remains trapped in the

seals. Periodic cleaning using a damp sponge will prevent

this from occurring.

GB

19

Cleaning and special maintenance

Cleaning the sprayer arms

Food residue may become encrusted onto the sprayer arms

and block the holes where water comes out; check them on

a regular basis and clean them (see the Close-up View (inside)

letters F-I).

Is there a problem?

Your dishwasher may not work or not function properly.

Before calling for assistance, let’s have a look at what can be

done: you may have forgotten to press a button or for some

reason or another you haven’t carried out a procedure

necessary for the appliance to operate correctly.

The dishwasher won’t start

Have you checked:

whether the tap has been turned on and is well connected

to the hose or whether there is no water throughout your

home or whether the pressure of the water supply is

sufficient, whether the hose is bent or the filter on the water

supply hose is blocked, whether the door is open?

The dishes are not clean

Have you checked:

whether the right amount of detergent is in the dispenser,

the wash cycle selected is suitable for the dishes loaded, or

whether the filter and the microfilter are clean and whether

the sprayer arms can turn freely?

The dishwasher won’t drain

Have you checked:

Is the drain hose bent?

Limescale deposits or a white film form on the dishes.

Have you checked:

whether the lid on the salt container is closed properly or

whether the amount of rinse aid has been adjusted correctly?

Error messages.

The dishwasher is equipped with a safety system which is able to

detect any operating anomalies. These anomalies are reported by

one or two wash cycle indicator lights “G” flashing rapidly. Take a

note of which lights are flashing, turn the appliance off and call for

technical assistance.

Tap off alarm

If you have forgotten to turn the water tap on, your appliance will

remind you of this by sounding a few short beeps for a few minutes.

Turn the tap on and your appliance will start up again after a few

minutes. Were you to be absent when these beeps are sounded,

the appliance will be blocked automatically and indicator lights 2

and 3 (wash and rinses) will flash rapidly. Turn the appliance off at

the ON-OFF button, turn on the water tap and wait approximately

20 seconds before turning the appliance back on, re-select a wash

cycle as indicated in the “Selecting the wash cycle” paragraph and

the appliance will start up again.

Clogged filter alarm

If the appliance is blocked and indicator lights 1 (pre-wash) and 3

(rinses) flash rapidly , this means the filter is clogged by large particles

of food residue. Turn the appliance off, clean the filter thoroughly,

reposition it in its seat and then turn the appliance on again. The

selected wash cycle will start up again.

Water load solenoid valve malfunction alarm.

If indicator light 2 (wash) flashes rapidly, TURN the dishwasher OFF

AND BACK ON AGAIN after one minute. If the alarm persists, first

turn off the water tap to avoid any flooding and then cut off the

electricity supply and call for technical assistance.

If any other indicator lights apart from the above-mentioned ones

flash rapidly, turn the appliance off and call for technical assistance.

If, despite all these checks, your dishwasher still won’t

work and the trouble you are having persists, call your

nearest authorised service centre, mentioning the

following information:

- the type of malfunction

- the model type no. (Mod. ....) and the serial number (S/N….)

indicated on the rating plate located on the inner door, to one side.

Never call upon the services of unauthorised

technicians and always refuse spare parts that are

not originals.

1

2

A

B

C

The filter assembly

If you want consistent good results from your dishwasher,

you need to clean the filter assembly.

The food particles are removed from the wash water, allowing

it to be recirculated during the cycle, filtered perfectly. For

this reason, it is a good idea to remove the larger food

particles trapped inside the cup “C” and the semi-circular

filter A after each wash; pull the cup handle upwards to

remove them. Just rinse them under running water.

The entire filter assembly should be cleaned thoroughly once

a month: cup C + semi-circular filter A + cylindrical filter B.

Rotate filter “B” anticlockwise to remove it.

For cleaning, use a non metallic brush.

Reassemble the filter parts (as shown in the figure) and

reinsert the whole assembly into the dishwasher. Position it

into its housing and press downwards.

The dishwasher is not to be used without filters. Improper

replacement of the filters may reduce the efficiency of the

wash and even damage your dishwasher.

20

GB

Installation

Positioning the appliance

Place your dishwasher where you want to install it. The

appliance can even be placed so that its sides or back panel

are side by side with furniture or up against the wall. The

dishwasher is provided with water supply and drain hoses,

which can be directed towards the left or right to facilitate

appropriate installation.

Levelling

Once the appliance is positioned, adjust the feet by screwing

them in or out depending on how high you want it and level

it so that it is horizontal; however it must not be tilted by

more than 2° under any circumstances.

If the appliance is level, this will help ensure its correct

operation.

This dishwasher model can be built under a single worktop

(please read the relevant instruction sheet).

Cold water connection.

This electric household appliance should be connected to

the water mains using the cold water supply hose provided

with the appliance only. Do not use a different hose. In the

event of replacements, use original spare parts only.

Connect the cold water supply hose to a 3/4 gas threaded

connection, taking care to screw it tightly onto the tap.

If the water hoses are new or have been out of use for an

extended period of time, let the water run to make sure it is

clear and free of impurities before making the connection.

If this precaution is not taken, the water inlet could get

blocked, causing damage to your dishwasher.

Hot water connection

Your dishwasher can be supplied with hot water from the

mains supply (if you have a central heating system with

radiators) at a temperature of no more than 60°C.

In this case, the wash cycle time will be about 15 minutes

shorter and the wash will be slightly less effective.

The connection must be made to the hot water supply

following the same procedures as those indicated for the

cold water connection.

Anti-flooding protection

Your dishwasher is provided with a special system which

blocks the water supply in the event of leaks inside the

appliance. It is further equipped with a water inlet hose that

can withstand extremely high pressures and that turns red

in the event of breakage. Safety in the event of flooding is

ensured by the second clear hose that contains the former.

It is vital that you check it on a regular basis: if you see it has

turned red, then you know you have to replace it as soon as

possible. Call for an authorised technical engineer to come

and replace it.

Drain hose connection

Fit the drain pipe into a drain line with a minimum diameter

of 4 cm or place it over the

sink. Avoid restricting or

bending it. Use the special

plastic elbow provided (see fi-

gure) to position it in the best

possible way. The part of the

pipe marked with the letter A

should be between 40 and

100 cm above the ground.

The pipe should not be

immersed in water.

Warning: the special plastic elbow should be fastened firmly

onto the wall to prevent the drain hose from moving and

allowing water to spill outside the drain.

Electrical connection

Plug the appliance into a socket provided with an efficient

earth connection (the system’s earthing is a guarantee of

safety provided for by law), after having checked that the

mains voltage and frequency values correspond to those

stated on the rating plate located on the stainless steel inner

door of the appliance and that the electrical system to which

the dishwasher is connected is sized for the maximum current

indicated on said rating plate. If the power socket to which

the appliance is connected is not compatible with the plug,

replace it with a suitable plug rather than using adapters or

multiple plugs as these could cause overheating or burns.

Caution: the dishwasher plug must be accessible so that

maintenance can be done safely.

If the electricity supply wire is damaged, we recommend you

contact authorised Technical Assistance service centres

exclusively for a replacement.

A

Page is loading ...

P12/2004 - N195048832.00 - Xerox Business Services - DocuTech

Viale Aristide Merloni 47

60044 Fabriano (AN) Italy

Tel +39 0732 6611

www.indesit.com

Whirlpool IDL 71 EU.2 Owner's manual

This manual is also suitable for

Whirlpool IDL 71 EU.2 Owner's manual

in other languages

Related papers

Other documents