QLIMA SRE 1330 TC User manual

SRE 1330 TC / SRE 1730 TC

3

2

6

5

4

>

u

1

9

:

=

SLO

FIN

MANUEL D’UTILISATION

GEBRAUCHSANWEISUNG

BRUGSANVISNING

INSTRUCCIONES DE USO

KÄYTTÖOHJE

OPERATING MANUAL

ISTRUZIONI D’USO

BRUKSANVISNING

GEBRUIKSAANWIJZING

MANUAL DE INSTRUÇÕES

INSTRUKCJI OBSŁUGI

BRUKSANVISNING

NAVODILA ZA UPORABO

4

16

28

40

52

64

76

88

100

112

124

136

148

Page is loading ...

Dear Sir, Madam,

Congratulations with your purchase of a portable domestic heater. You have

purchased a quality product, which will serve you for many years to come. This,

of course, provided you use the heater correctly. Please read these Directions

for Use first, to ensure maximum lifetime for your heater.

Your heater comes with a 24-month manufacturer’s warranty on all defects in

materials or workmanship.

We wish you a warm and comfortable time with your heater.

Yours sincerely,

PVG Holding b.v.

Customer Service Department

1 READ THE DIRECTIONS FOR USE FIRST.

2 IN CASE OF ANY DOUBT, CONTACT YOUR DEALER.

4

64

GENERAL DIRECTIONS FOR USE

Below you will find the main steps to be taken for

using your heater. For more details, please refer to

the MANUAL (pages 67 ff.).

MAIN COMPONENTS

4

• As a fire precaution, the tank must be filled either

when the heater has been switched off or in

another room than the room where the heater is

installed.

• Always ensure that the tank is closed properly after

filling it at a safe distance from all sources of heat

and open flames (see chapter B).

• The first time the heater is ignited it will smell like

“new” for a short time.

• Store all fuel containers with their original caps and

seals in a cool and dark place.

• Fuel ages. Use new fuel at the start of every heating

season.

• The use of Qlima Premium Quality Fuels as a heating

fuel assures you that you have a good quality fuel.

• Before changing brands and/or types of fuel make

sure that the mobile heater first completely empties

all of the remaining fuel inside the heater.

Information display

Operating keys

Tank compartment

lid

Removable tank

Metal cap

Fuel filter

Fixed tank

Flame inspection

window

Hot air grille

Air supply

Safety bracket

Filter ventilator

Plug

Connecting lead

Child safety catch

key

Low fuel level indi-

cator

Green timer indica-

tor

Timer key

Mode key

Key to set tempera-

ture/time

On/off key (red indi-

cator on)

A

B

C

4

E

F

G

H

I

J

K

L

M

N

O

P

Q

R

S





Remove all packaging materials (refer to Section A, Fig. A).

Fill the removable tank 4 (refer to Section B, Fig. C-F).

Insert the plug into the wall-socket.

Ignite the heater using the ON-OFF key

21

(refer to Section D).

If required, change the temperature using the adjustment keys

 (refer to Section E).

Switch off the heater by pressing the ON-OFF key

21

.

1

2

3

4

5

6

1 READ THE DIRECTIONS FOR USE FIRST.

2 IN CASE OF ANY DOUBT, CONTACT YOUR DEALER.

21

65

WHAT YOU NEED TO KNOW IN ADVANCE

Read this user manual carefully before using the appliance and keep it for future

reference. Install this device only when it complies with local/national legislation,

ordinances and standards. This product is intended to be used as a heater in

residential houses and is only suitable for use in dry locations, in normal household

conditions, indoors in living room, kitchen and garage.

Regardless of the model, you must always make sure that the heater is used in

a room large enough to enable the heater to be used safely without extra

ventilation. If the room is smaller than required, you must always open a door or

window slightly (ensuring an opening of approx. 2.5 cm). It is important that every

room where the heater is used has sufficient air intake and efficient air outflow

(both openings must have a minimum cross section of 50 cm

2

). No modifications

to the safety system are allowed, as that will invalidate the guarantee that the air

probe will work properly. Consult your dealer in case of doubt.

Especially for France: Your heater was designed to operate exclusively on fuel for

liquid fuel-operated mobile heaters in accordance with the Decrees of 18-07-2002

and 25-06-2010. The use of other fuels is forbidden.

Ask your dealer or check our website for the addresses of our retailers.

The liquid fuel-operated mobile heater is intended as an extra heater, and not as a

continuous source of heat.

Especially for United Kingdom: Only use Class C1 paraffin fuel in accordance with

BS2869; Part 2, or equivalent.

The user must comply with the following instructions for proper use:

DO NOT

- use the liquid fuel-operated mobile heater in caravans, boats, and vehicle cabins;

- use the liquid fuel-operated mobile heater in insufficiently ventilated rooms

(consult the table of properties for the minimum dimensions of the room to be

heated), underground rooms and / or at a height of over 1500 metres;

- modify the heater safety features.

The use of this type of heating in public rooms is subject to prior regulatory

permission. Obtain proper information on this in advance.

THE RIGHT FUEL

Your heater has been designed for use with high-quality water-free pure paraffin

oil, such as Qlima Premium Quality Fuels. Only fuels of this kind will ensure clean

and proper burning. Lower quality fuel may result in:

E increased possibility of malfunctioning

E incomplete combustion

E reduced heater lifetime

E smoke and/or fumes

E deposits on the grid or mantle

Using the right fuel is therefore essential for safe, efficient, and comfortable use

of your heater.

Damage and/or malfunctions of the heater due to the use of other than high-

quality water-free pure parafine oil is not covered by the warranty.

Always refer to your local dealer for the right fuel for your heater.

4

This transportation cap

is packed separately in

the box. Only this cap

ensures trouble-free

transportation of the

heater after use.

Store it well!

Only the use of the

correct fuel will ensure

safe, efficient, and

comfortable use of your

heater.

66

MANUAL

A INSTALLING THE HEATER

1

Carefully remove your heater from the box and check the contents.

In addition to the heater you also need to have:

E a transportation cap

E these directions for use

Keep the box and the packaging materials (Fig. A) for storage and/or

transportation.

2

Open the lid of the removable tank C and remove the piece of cardboard.

3

Fill the removable tank as indicated in Section B.

4

The floor should be firm and completely level. Reposition the heater, when it

is not level. Do not try to correct the situation by placing books or other

goods under the heater.

5

Use the horizontal safety bracket K to prevent the curtains from covering the

ventilator (Fig. B.).

6

Insert the plug M into the wall-socket (230 Volts - AC / 50 Hz) and set the

correct time using the adjustment keys  (refer to Section C).

7

Your heater is now ready for use.

B FILLING FUEL

Fill the removable tank in a suitable place since there can always be some spillage.

Follow the procedure below:

1

Make sure that the heater is switched off.

2

Open the upper lid and lift the removable tank out of the heater (Fig. C).

Note: Some drops may leak from the tank. Put down the removable tank

(cap pointing upwards, handle on floor and screw off the fuel cap.

3

Remove the metal cap (unscrew). Easy to open by holding the outside (fig. D.).

4

Fill the removable tank using a fuel pump (refer to fuel pump operation

instructions.) Make sure that it is in a higher position than the removable tank

(Fig. E). Insert the ribbed hose into the opening of the removable tank.

5

Check the removable tank fuel gauge while filling the tank (Fig. F). Stop

filling once the gauge indicates that the tank is full. Never overfill the tank,

especially not when the fuel is very cold (fuel expands when it heats up).

6

Let the remaining fuel in the pump flow back into the jerrycan and carefully

4

E E E E E E

67

A

B

C

D

E

+

4

+

remove the pump. Carefully screw the fuel cap back on the tank. Clean off

any spilled fuel.

7

Check whether the fuel cap is straight and tightened properly. Reinstall the

removable tank in the heater (cap down). Close the lid.

• Do not move the heater after reinstalling the tank.

• Take care not to damage the cap while filling the tank. Deformation of the cap

can lead to fuel leakage.

8

Turn the heater on again.

C SETTING THE TIME

Set the time to use the heater as a clock or if using the timer. You can even set

the time when the heater is on.

1

Press the mode key S to set the time (fig. G). Time set and the time flash on

the display.

2

Press the buttons (-) or (+)

20

to set the time. The time displays the numbers

00:00 to 23:59. Press the ( + ) button to go forwards and the ( - ) button to go

backwards. The time will change in one minute steps each time you press one of

these 2 buttons. The time on the display will change in ten minute steps if you

keep the button pressed (fig. H.).

3

Press the mode key S again to activate the timer function. See chapter F.

4

Press the mode key S to display the time (fig. I.). If the time is not set, the

display indicates --:--.

The time must be set again after a power cut or if the plug has been removed

from the socket.

D IGNITING THE HEATER

When used for the first time, a new heater may give out a smell for a short while.

You should therefore provide extra ventilation.

Always ignite the heater with the ON / OFF

button

21

. Never use matches or a

cigarette lighter.

1

Press the ON / OFF button

21

.

The ignition indicator will light up: the required temperature and the ambient

temperature are displayed (fig. J.). The ambient temperature is displayed from

1ºC. If the temperature is below 0ºC, Lo is displayed. Ignition takes about 45

seconds.

2

Normal combustion:

• T he flames are blue

• The burner grille can become red

68

G

H

I

J

F

empty full

+ +

+

4

Abnormal combustion:

• The flame is yellow and blue In this case take appropriate measures.

This heater cannot be switched on continuously for more than 36 hours. After 36

hours it stops automatically, even if the tank has been refilled within this period.

E SETTING THE REQUIRED TEMPERATURE

If the heater is on, the required temperature can be changed using the adjustment

buttons

20

(fig. K). To increase the temperature, press the + button. To decrease

the temperature, press the - button. Each time you press the adjustment button

the temperature changes by 1ºC. The temperature can be set to a minimum of

12ºC and a maximum of 26ºC.

• If the heater is used in a small space, in a well-insulated space or if the outside

temperature is relatively high, the ambient temperature can become higher

than the required temperature. In this case, turn the heater off.

• The displayed temperature is the mean ambient temperature. This

temperature may not correspond with that indicated by a thermometer.

F USING THE TIMER

The timer allows you to switch on the heater automatically at a preset time.

In order to switch on the timer, the correct time must have been set (refer to

Section C) and the heater should be off. Follow the procedure below:

1

Check that the time is set properly (see chapter C).

2

Press the mode button S (fig. L) until Timer and Set appear in the display.

3

Press the ( - ) or ( + ) buttons  to set the required activation time for the

heater. Press the ( + ) button to go forwards and the ( - ) button to go backwards.

The time will change in one minute steps each time you press one of these 2

buttons. The time on the display will change in ten minute steps if you keep

the button pressed (fig. M).

4

Press the ON / OFF buttons

21

to turn the heater on (the indicator will light up).

It is not necessary to press this button if the heater is on.

5

Press the timer button R. The indicator goes out. The time indicator will light

up and the timer is set.

Take care not to press the ON / OFF button

21

again after setting the timer, this

will reset the timer.

6

The heater turns on at the time chosen.

• To cancel the timer, press the ON / OFF button

21

(the timer indicator goes

out).

• Set the timer and the clock again after a power cut.

• In case of an earthquake, or shocks, code E01 will appear in the display. Reset

the error and repeat from point 4 to set the timer again.

69

K

L

M

N

+

4

G TURNING THE HEATER OFF

1

Press the ON / OFF button

21

. The red lamp flashes for about 8 seconds and the

heater is turned off. Always check that the flame goes out.

The ventilator continues operating for about 3 minutes after turning off in order

to cool the inside of the heater. If you turn off the power earlier, uncontrolled

symptoms can occur (release of smoke, smell etc.)..

H IN CASE OF PROBLEMS

The symptoms mentioned above are not faults and not abnormal.

Check the list.

Symptoms Causes

While igniting

Igniting is tedious

Igniting takes about 45 seconds.

After filling the tank, wait till

the fuel has reached the fixed

tank. Repeat ignition 2 or 3

times.

Crackling sound

This sound is made by the elec-

tric ignition.

White smoke

This can happen if the fuel does

not circulate past the burner

properly

During ignition

or turning off

Smoke and an unpleasant smell

during first use

That is the protective lacquer

getting warm. This soon stops.

Give the space more ventila-

tion.

The ambient temperature does

not increase and the requested

temperature is higher.

The space is too large.

The flame glows red.

The ambient air is damp or salty

or it contains too many impu-

rities.

The ambient temperature does

not decrease and the requested

temperature is lower.

The heater is being used in a

small insulated space or the

outside temperature is relati-

vely high. Turn the heater off.

The displayed ambient tempe-

rature is not the same as indica-

ted by a thermometer.

This is because the displayed

ambient temperature is an indi-

cation of the average tempera-

ture of the space.

Small knocking noises when the

heater is in operation or imme-

diately after turning off.

This is the sound of the metal

expanding.

Noise 8 seconds after turning

off.

A ticking sound: can occur

when the heater cools off.

70

4

THE INFORMATION DISPLAY

The information display  not only serves as an indicator of the (set) time and

temperature (sections C, E, and F), it also indicates any malfunctioning of the

heater. The code on the information display tells you what is the matter:

Code Information Action

Time

----

The heater has been automa-

tically turned off by a power

cut or bad connection.

Restore power or restore the

connection. Press the ON /

OFF key

21

again.

E01

An earthquake (magnitude 5

or more), strong vibrations or

a shock will ensure that the

heater automatically

turns off. (The safety system

against shocks has worked).

Make sure there are no com-

bustible materials around the

heater, or fuel leakages. Press

the ON / OFF key

21

again.

E02

E03

The heater has been automa-

tically turned off after a fault

or during ignition or due to

the presence of water or dust

in the fuel filter or in the

fixed tank.

Remove the water and the

dust in the fixed tank. Clean

the fuel filter (see chapter K).

Press the ON / OFF button

21

again.

E07

An increase in ambient

temperature has turned the

heater off. (The tempera-

ture monitoring system has

worked).

Ventilate the space. Let the

heater cool off. Press the ON /

OFF button

21

again.

Filter

E09

Filter

The heater has been automa-

tically turned off because the

hot air stream, the ventila-

tor or the ventilator filter

is blocked or hindered by

something. (The safety system

against overheating has

worked).

Remove obstacles from the

ventilator opening. Clean the

ventilator filter (see chapter

K) Press the ON/OFF button

21

again. If the problem oc-

curs again after taking the

above measures, contact your

dealer.

E13

The heater has been turned

off in a closed space. (The

safety system against incom-

plete combustion has wor-

ked).

Ventilate the space and press

the ON / OFF button

21

again.

Ensure the space is sufficien-

tly ventilated.

The ON indica-

tor flashes. Err

lights up

The heater has automatically

stopped because the ON / OFF

button was kept pressed in or

was blocked.

Remove obstacles from the

ventilator opening. Clean the

ventilator filter (see chapter

K) Press the ON/OFF button

21

again. If the problem oc-

curs again after taking the

above measures, contact your

dealer.

F00 – F30

Poor functioning. Heater

needs maintenance

Note the messages displayed

and turn the heater off. Con-

tact your dealer.

71

4

Symptoms Causes Measures to be taken

Heater doesn’t

ignite

The child safety catch lights

up

Turn the child safety catch off

The fuel in-

dicator lamp

doesn’t work

The tank is empty Fill the tank

The tank is deformed Replace the tank

Dirt particles dust or water on

the filter and / or in the fixed

tank

Clean the fixed tank and the

fuel filter.

Power loss

The fuel indicator flashes

The fuel indicator flashes Fill the tank

A poor quality fuel has been

used.

Remove the fuel from the

two tanks, then rinse with the

correct fuel.

Abnormal com-

bustion

A poor quality fuel has been

used.

Poor ventilation Ventilate regularly

Dust on the ventilator filter Clean the ventilator filter

Unpleasant

smells

A poor quality fuel has been

used

Remove the fuel from the

two tanks, then rinse with the

correct fuel.

No fuel in the tank Fill the tank

Fuel leakage or spilled fuel

Do not use any more and

contact your dealer

Fuel leakage

Move the heater, the tank is

not empty

A poor quality fuel has been

used.

AUTOMATIC DEACTIVATION

This heater is fitted with a safety system that ensures that it switches off

automatically after 36 hours continuous operation. If desired, you can switch the

heater on again by pressing the ON/OFF button

21

(see section D).

I CHILDPROOF LOCK

The childproof lock can be used to prevent children accidentally changing the

heater settings. When the heater is burning and the childproof lock is on, the heater

can only be switched off. Other functions are blocked then. If the heater has already

been switched off, the childproof lock also prevents accidental ignition of the

heater.

Activate the childproof lock by pressing the CHILDLOCK key O and holding it

down for more than 3 seconds. The childlock indicator will appear on the information

display (Fig. O), indicating that the childproof lock has been activated. Switch off the

childproof lock by pressing the CHILDLOCK key O and holding it down for more than

3 seconds once again.

J THE ‘OIL’ INDICATOR

If the low fuel level indicator P lights up in combination with a short tone, then

the fuel tank is empty. The heater will automatically burn at its lowest setting

for a period of about 80 minutes. The fuel tank must be replenished.

72

O

+

E remove the removable tank from the heater and fill it with new fuel (outside

the living space in a safe place) (see chapter B)

If you take no action, the fuel tank will be emptied and the display will indicate

“E 03” (fig. Q). The heater is automatically turned off.

To ignite the heater once more, fill the tank and wait a few minutes.

Then press the ON / OFF button

21

.

K MAINTENANCE

Switch off the heater and let it cool down, before you start any maintenance

work. Also disconnect the plug from the mains. Your heater needs hardly any

maintenance.

Clean the ventilator filter:

1

Press the buttons on top left and right. Pull the filter 1 cm towards you. Move

the filter up so that the two lower fixing points come loose.

2

Clean the ventilator.

3

Replace the ventilator.

Clean the fuel filter:

1

Remove the removable tank 4 from the heater and remove the fuel filter

(Fig. S). Some drops may leak from the filter; keep a cloth at hand.

2

Remove the dirt by tapping the fuel filter upside-down against a hard surface.

(Never clean it with water!)

3

Reinstall the fuel filter into the heater.

We recommend that you remove dust and stains from time to time with a damp

cloth, because otherwise these may cause stains that are hard to remove.

Do not use solvents or alcohol to clean the heater: fire hazard.

Clean very dirty components with a light synthetic cleaning agent.

Do not remove any heater components yourself. Always contact your dealer for

repairs.

When the power cord is damaged, it may only be replaced by an authorised

fitter. Use a new cord of the type H05 VV-F.

4

73

P

Q

R

S

Fuel filter

T

+

4

L STORAGE (END OF THE HEATING SEASON)

At the end of the heating season, you must store the heater in a dust-free place, if

possible in its original packaging. Unused fuel cannot be used in the next heating

season. We therefore recommend that you burn up all fuel. If there is still some

fuel left, do not throw it away, but dispose of it in accordance with the local

regulations for the disposal of domestic chemical waste.

Always start the new heating season with fresh fuel. When you start re-using the

heater follow the instructions again (starting from section A and as specified).

M TRANSPORTATION

Take the following measures to avoid fuel leakage during the transportation of

the heater:

1

Let the heater cool down.

2

Remove the removable tank 4 from the heater and remove the fuel filter.

Some drops may leak from the filter; keep a cloth at hand. Store the fuel filter

and the removable tank outside the heater.

3

Empty the fixed fuel tank (fig. U).

4

Place the transport cap.

5

Always move the heater in an upright position.

Make the fixed tank empty with a fuel pump before transportation or in case

of wrong or dirty fuel. First remove the fuel filter and then insert the fuel pump

into the empty fixed tank. Follow the same procedure if the fuel tank contains

water.

N SPECIFICATIONS

Ignition electrical Dimensions (mm) width 371

Fuel paraffin (including base plate) depth 294

Capacity (kW) max. 3,00 height 429

Capacity (kW) min. 1,08 Accessories: - transportation cap

Suitable space (m³)** 48-120

Fuel consumption (l/hr)* 0,313 Mains 230 V

-- AC 50 Hz

Fuel consumption (g/hr)* 250 Electrical consumption:

Burning time per tank (hr)* 16 - igniter 335 W

Capacity removable tank (litres) 5 - continuous 78 - 123 W

Weight (kg) 8,1 Fuse rating 250V, 5A

* At maximum setting ** Specified values are indicative

The CE marking corresponds with the compliance with the standards EN 60-335

part 1 (1995) and EN 50-165 (08/97)

U

74

Transport cap

O WARRANTY PROVISIONS

Your heater comes with a 24-month warranty starting on the date of purchase.

Within this period all defects in material or workmanship will be repaired without

any charge. The following provisions shall apply regarding this warranty:

1

We expressly dismiss all other claims for damages, including consequential

damages.

2

Any repairs or replacements of components within the term of warranty will

not result in an extension of the term of warranty.

3

The warranty shall no longer apply, when the heater has been modified,

non-original parts have been used, or when it is repaired by third parties.

4

The warranty shall not apply to parts that are subject to normal wear, such as

the manual fuel pump.

5

The warranty shall only apply, when you present the original, dated proof of

purchase, provided no changes have been made to it.

6

The warranty shall not apply to damages caused by actions not in compliance

with the Directions for Use, neglect, and the use of an incorrect type of fuel,

or fuel past its use-by date. The use of incorrect fuel can even be dangerous*.

7

Transportation costs and the risks involved during the transportation of the

heater or heater components shall always be at the expense of the purchaser.

In order to avoid unnecessary costs, we recommend that you always read the

’Directions for Use’ carefully first. In case they offer no solution, please take the

heater to your dealer for repair.

* Highly inflammable substances may induce uncontrollable burning, causing flames to break out. Should this

happen, never try to move the heater, but always switch off the heater immediately. In case of emergency you

may use a fire extinguisher, but only a type B extinguisher: a carbon dioxide or powder extinguisher.

4

75

Page is loading ...

QLIMA SRE 1330 TC User manual

This manual is also suitable for

QLIMA SRE 1330 TC User manual

in other languages

Related papers

Other documents