Bosch Power Tools 1942 User manual

Operating/Safety Instructions

Consignes de fonctionnement/sécurité

Instrucciones de funcionamiento

y seguridad

IMPORTANT: IMPORTANT : IMPORTANTE:

Read Before Using Lire avant usage Leer antes de usar

For English Parlez-vous français? ¿Habla español?

See page 2 Voir page 11 Ver página 20

Consumer Information

Renseignement des consommateurs

Información para el consumidor

Toll Free Number: Appel gratuit : Número de teléfono gratuito:

1-877-BOSCH99 (1-877-267-2499) http://www.boschtools.com.

1942

BM 2610615924 2/02 2/1/02 12:36 PM Page 1

-2-

Paint Stripping Safety Instructions

Extreme care should be

taken when stripping

paint. The peelings, residue and vapors of

paint may contain lead, which is poisonous.

Any pre-1977 paint may contain lead and

paint applied to homes prior to 1950 is likely

to contain lead. Once deposited on surfaces,

hand to mouth contact can result in the

ingestion of lead. Exposure to even low

levels of lead can cause irreversible brain

and nervous system damage; young and

unborn children are particularly vulnerable.

Before beginning any paint removal process

you should determine whether the paint you

are removing contains lead. This can be

done by your local health department or by a

professional who uses a paint analyzer to

check the lead content of the paint to be

removed. LEAD-BASED PAINT SHOULD

ONLY BE REMOVED BY A PROFESSIONAL

AND MUST NOT BE REMOVED USING A

HEAT GUN.

Persons removing paint should follow

these guidelines:

1) Move the work piece outdoors. If this is

not possible, keep the work area well

ventilated. Open the windows and put an

exhaust fan in one of them. Be sure the fan

is moving the air from inside to outside.

2) Remove or cover any household items

in the area such as carpets, rugs,

furniture, and clothing, cooking utensils

and air ducts.

3) Place drop cloths in the work area to

catch any paint chips or peelings. Wear

protective clothing such as extra work shirts,

overalls and hats.

4) Work in one room at a time. Furnishings

should be removed or placed in the center of

the room and covered. Work areas should

be sealed off from the rest of the dwelling by

sealing doorways with drop cloths.

5) Children, pregnant or potentially

pregnant women and nursing mothers

should not be present in the work area

until the work is done and all clean up is

complete.

6) Wear a dust respirator mask or a dual

filter (dust and fume) respirator mask,

which has been approved by the

Occupational Safety and Health

Administration (OSHA), the National

Institute of Safety and Health (NIOSH), or

the United States Bureau of Mines. These

masks and replaceable filters are readily

available at major hardware stores. Be sure

the mask fits. Beards and facial hair may

keep masks from sealing properly. Change

filters often. DISPOSABLE PAPER MASKS

ARE NOT ADEQUATE.

7) Use caution when operating the heat

gun. Keep the heat gun moving, as

excessive heat will generate fumes that can

be inhaled by the operator.

8) Keep food and drink out of the work

area. Wash hands, arms and face and rinse

mouth before eating or drinking. Do not

smoke or chew gum or tobacco in the work

area.

!

WARNING

Important Safety Instructions for Heat Guns

SAVE THESE INSTRUCTIONS

Read and understand all instructions. Failure to follow all instructions

listed below, may result in electric shock, fire and/or serious personal injury.

!

WARNING

Hidden areas such as behind walls, ceilings, floors, soffit boards and other panels may

contain flammable materials (dust, cob webs, mice nests, etc.) that could be ignited by

the heat gun when working in these locations. The ignition of these materials may not be

readily apparent and could result in property damage and injury to persons.

When working in locations that may have hidden areas, keep the heat gun moving in a

back-and-forth motion. Lingering or pausing in one spot could ignite the panel or the

material behind it.

BM 2610615924 2/02 2/1/02 12:36 PM Page 2

-3-

General Safety Rules for Heat Guns

Never use heat guns as

hairdryers! You will be

seriously injured.

Avoid contact with nozzle of heat gun

during use. This heat gun generates

temperatures as high as 1000 degrees

Fahrenheit. You may be seriously burned.

Do not use heat guns in the rain, moisture

or immerse in water. Exposing the heat

gun element to water or other liquids may

cause electrical shock hazard.

Do not use heat guns in areas where

flammable liquids or gases may be stored

or are present. The heat gun generates

high temperatures and may ignite these

materials.

Work Area

Keep your work area clean and well lit.

Cluttered and dark areas invite accidents.

Do not operate heating appliance in

explosive atmospheres, such as in the

presence of flammable liquids, gases or

dust, dry grass, leaves and paper. Heating

appliances generate high temperatures

which may ignite the dust or fumes.

Combustible materials like dry grass, leaves

and paper will scorch and may catch fire.

Keep bystanders, children and visitors

away while operating a heating appliance.

Distractions can cause you to lose control.

Electrical Safety

Before plugging in the heating appliance,

be certain the outlet voltage supplied is

compatible with the voltage marked on

the nameplate within 10%. An outlet

voltage incompatible with that specified on

the nameplate can result in serious hazards

and damage to the heating appliance.

When operating a heating appliance use

Ground Fault Circuit Interrupter (GFCI) on

the circuit or outlet. Don’t expose heating

appliance to rain or wet conditions. Water

entering a heating appliance will create an

electric shock hazard.

Do not abuse the cord. Never use the

cord to carry the heating appliance or pull

the plug from an outlet. Keep cord away

from heat, oil, sharp edges or moving

parts. Replace damaged cords

immediately. Damaged cords create

electric shock hazard.

9) Clean up all removed paint and dust by

wet mopping the floors. Use a wet cloth to

clean all walls, sills and any other surface

where paint or dust is clinging. DO NOT

SWEEP, DRY DUST OR VACUUM. Use a

high phosphate detergent or trisodium

phosphate (TSP) to wash and mop areas.

10) At the end of each work session put

the paint chips and debris in a double

plastic bag, close it with tape or twist ties

and dispose of properly.

11) Remove protective clothing and work

shoes in the work area to avoid carrying

dust into the rest of the dwelling. Wash

work clothes separately. Wipe shoes off with

a wet rag that is then washed with the work

clothes. Wash hair and body thoroughly with

soap and water.

Some dust created by

power sanding, sawing,

grinding, drilling, and other construction

activities contains chemicals known to

cause cancer, birth defects or other

reproductive harm. Some examples of

these chemicals are:

• Lead from lead-based paints,

• Crystalline silica from bricks and cement

and other masonry products, and

• Arsenic and chromium from chemically-

treated lumber.

Your risk from these exposures varies,

depending on how often you do this type of

work. To reduce your exposure to these

chemicals: work in a well ventilated area,

and work with approved safety equipment,

such as those dust masks that are specially

designed to filter out microscopic particles.

!

DANGER

!

WARNING

BM 2610615924 2/02 2/1/02 12:36 PM Page 3

-4-

When operating a heating appliance with an

extension cord while outdoors, use only

extension cords marked W–A or W. These

cords are rated for outdoor use and

reduce the risk of electric shock.

Personal Safety

Stay alert, watch what you are doing and

use COMMON SENSE when operating a

heating appliance. A moment of inattention

or use of drugs, alcohol or medication while

operating a heating appliance can be

dangerous.

Use safety equipment. Always wear safety

goggles. Dust mask, protective gloves,

safety shoes or non-skid shoes, must be

used for appropriate conditions.

Avoid accidental starting. Be sure switch

is “OFF” before plugging in. Carrying the

heating appliance with your finger on the

switch or plugging in the heating appliance

that has switch “ON” invites accidents.

Do not direct hot tip or nozzle toward

clothing, hands or other body parts.

Intense heat from tip or nozzle can cause

serious burns or cause clothing to ignite.

Do not touch nozzle or shield until

completely cool. During use very high

temperatures are generated in these areas.

Dress properly. Do not wear loose

clothing or jewelry. Contain long hair.

Keep your hair, body, clothing and gloves

away from nozzle or shield. Clothing or

hair could ignite from extreme heat.

Do not overreach, keep proper footing

and balance at all times. Proper footing

and balance enables better control of the

heating appliance in unexpected situations.

Tool Use and Care

Do not use heating appliance if switch

does not turn it “ON” or “OFF”. Any tool

which cannot be controlled by the switch is

dangerous.

Disconnect the plug from the power

source before making any adjustments or

changing accessories. Such preventative

safety measures reduce the risk of starting

the heating appliance accidentally.

Store idle heating appliance only after

adequate cooling period, indoors in high,

dry place out of the reach of children and

untrained persons. Heating appliances are

dangerous in the hands of untrained

persons.

Do not leave heating appliance

unattended while it is running or cooling

down. Always set tool on a flat, level surface

so that nozzle tip is directed upwards, away

from supporting surface while running or

cooling down.

Keep a fully charged fire extinguisher

close at hand for emergency use.

Service

Heating appliance service must be

performed only by qualified repair

personnel. Service or maintenance

performed by unqualified personnel may

result in misplacing internal wiring and

components which could cause serious

hazard.

BM 2610615924 2/02 2/1/02 12:36 PM Page 4

-5-

If an extension cord is

necessary, a cord with

adequate size conductors that is capable

of carrying the current necessary for your

tool must be used. This will prevent

excessive voltage drop, loss of power or

overheating. Grounded tools must use 3-

wire extension cords that have 3-prong

plugs and receptacles.

NOTE: The smaller the gauge number, the

heavier the cord.

RECOMMENDED SIZES OF EXTENSION CORDS

120 VOLT ALTERNATING CURRENT TOOLS

Tool’s

Ampere

Rating

Cord Size in A.W.G.

Wire Sizes in mm

2

3-6

6-8

8-10

10-12

12-16

18 16 16 14 .75 .75 1.5 2.5

18 16 14 12 .75 1.0 2.5 4.0

16 16 14 12 1.0 2.5 4.0 —

14 12 — — — — — —

25 50 100 150 15 30 60 120

Cord Length in Feet Cord Length in Meters

!

WARNING

Improper grounding can

shock, burn or electrocute.

Grounding of this tool is necessary while in

use to protect you from electric shock or

electrocution. This tool is equipped with an

approved three-conductor cord and three-

prong grounding-type plug to fit the proper

grounding-type receptacle. Do not remove

grounding prong from the three prong

grounding-type plug. The green (or green

and yellow) conductor in the cord is the

grounding wire. Never connect the green (or

green and yellow) wire to a live terminal.

Your unit is for use on less than 150 volts

and it has a plug that looks like Fig. “A”.

An adapter, Fig. “B” and “C” is available for

connecting Fig. “A” plugs to two-prong

receptacles. The green colored rigid ear, lug,

etc., extending from the adapter must be

connected to a permanent ground such as a

properly grounded outlet box.

NOTE: The grounding adapter, Fig. “C” is

prohibited in Canada by Canadian Electrical

Code-Part 1. Therefore the instructions for

its use are not applicable in Canada.

Grounding Instructions For Tools With Three Prong Plugs

If your unit is for use on 150 to 250 volts, it

has a plug that looks like Fig. “D” plugs. No

adapter is available for a plug like Fig. “D”.

Grounding

Prong

FIG. D

Grounding

Means

Adapter

FIG. C

Cover of Grounded

Outlet Box

FIG. B

Grounding

Prong

FIG. A

!

WARNING

BM 2610615924 2/02 2/1/02 12:36 PM Page 5

-6-

Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8"L x 5-1/4"W x 9-1/2”H

Nozzle opening . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3/16" dia.

Avg. air velocity . . . . . . . . . . . . . . . . . . . . . . . 3000 FPM at ambient

Avg. air volume . . . . . . . . . . . . . . . . . . . . . . . . . 23 CFM at ambient

Net weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1/2 Ibs.

120V models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 Hz

Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . 750ºF (400ºC)

1000ºF (540ºC)

Nozzle shield . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3/16” L

Cord length. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Ft. L

Functional Description and Specifications

Disconnect the plug from the power source before making any

assembly, adjustments or changing accessories. Such preventive safety

measures reduce the risk of starting the tool accidentally.

!

WARNING

Heat Gun

ADJUSTABLE

STAND

ROCKER

SWITCH

NOZZLE

ASSEMBLY

AIR INTAKE

SHUTTER

HANDLE

BM 2610615924 2/02 2/1/02 12:36 PM Page 6

-7-

Operating Instructions

Your Bosch Heat Gun is a heavy-duty,

industrial-quality, general-purpose heat gun.

You can do more heating jobs faster with this

heat gun because of its high power and air

flow ratings.

This product provides a fast flow of heated

air for applications such as activating

adhesives, bending and forming plastics,

curing epoxies, deburring plastics, defrosting

frozen coils, drying negatives and parts,

heating solids and liquids, loosening nuts

and bolts, removing floor tiles and putty,

repairing vinyl, shrinking tubing and

packaging, softening materials and stripping

paint. It's your dependable answer,

“Wherever a fast, portable heat is the need.”

The proper amount of heat for each

application is dependent upon the

adjustment of the air intake shutter, the

distance of the nozzle opening from the work

surface and length of time that heat is

applied to the work surface.

Before performing an application, we

recommend that you experiment with a piece

of scrap material. Use care in approaching

the work until you find the proper

combination of shutter adjustment, distance

from the work surface and heat application

time.

Use a gentle back and forth motion when

applying heat unless it is found that a

concentrated heat is desired.

TO OPERATE HEAT GUN

1) Plug heat gun into properly rated outlet.

2) Move rocker switch to “Hot” position. Heat

gun will come up to full operating

temperature in approximately two minutes.

3) Adjust air intake shutter to desired

position. Open will provide slightly cooler

air. Closed will provide the highest

temperature.

4) Adjustable stand is provided to allow

nozzle to be rotated from almost horizontal

to vertical position.

5) To turn heat gun off after use, move switch

to “COLD” position. Run on cold for

approximately three minutes. This will

allow the heat gun to cool down and the

nozzle to become cool to the touch.

6) Move switch to "OFF" position.

When heat gun is used in an enclosed

container, such as a shrink tunnel or special

enclosure, ambient air must be allowed to

pass into the heat gun and there must be an

outlet of equal size for the heated air to pass

out of the enclosure also. Total enclosure will

cause damage or possible failure to the heat

gun due to the extreme heat generated.

Typical Applications

STRIPPING PAINT

1) To strip paint, turn unit on and hold it

about 1 inch from the surface being

stripped. Proper distance and speed of

stripping should be determined by

experience. It is an advantage to hold the

gun further from the surface and to move

forward slowly. Slower speed is

compensated by the wider softened areas.

Heat will also penetrate deeper.

2) Outlet temperature can be regulated by

the shutter at the side of the unit. With

shutter open, temperature is about

750°F/400°C at a distance of 1 inch from

the nozzle. With shutter closed,

temperature is about 1000°F/540°C.

Experiment to see which setting gives the

best results with the paint you are

stripping.

BM 2610615924 2/02 2/1/02 12:36 PM Page 7

3) As paint begins to blister and bubble,

move gun slowly in a steady progression

across the surface. Follow closely with a

scraping knife (a 2-inch wall scraper works

best) to scrape the loosened paint. Preheat

scraper as you are heating the paint

surface. This increases the speed of paint

stripping.

a. Removal of paint by using heat is based

on the fact that all organic paints soften

at elevated temperatures. When soft,

the paint can be easily lifted off without

damage to the surface.

b. When stripping paint from grooves in

moldings, you can devise your own

scraping tools. Old screwdrivers with

ground-down blades and linoleum

knives are often used.

4) When the task is completed, move rocker

switch to "Cool" position. Allow blower to

operate for a few minutes on cool.

SHRINKING TUBING

Use stand to free both hands. Slide tubing

over area to be insulated. Place in air stream

and move with a side to side motion until

tubing has shrunk. Remove from air stream.

SHRINKING PACKAGING

After shrink wrap has been sealed around

product, poke a small hole in it to allow

trapped air to escape. Then wave heated air

stream back and forth across package until

shrink wrap has evenly shrunk.

REMOVING FLOOR TILE

Direct heated air stream at tile to be removed

in a back and forth motion. This will soften

the adhesive backing. Place putty knife under

tile and lift to remove.

BENDING AND FORMING PLASTICS

Experiment with a piece of scrap material

first to develop a proper technique. Place

plastic piece into a proper holding fixture.

Wave hot air along the whole length of the

“Bend” line until plastic softens along that

area. Bend plastic to desired position.

REMOVING OLD PUTTY

When removing putty from a broken window,

carefully remove the broken glass first. When

removing putty from an undamaged window,

direct the hot air stream away from the glass

to prevent cracking due to thermal shock. It

is convenient to shield the glass from the hot

air with a large putty knife. Wave the hot air

stream at putty until softened. Remove with

putty knife.

-8-

BM 2610615924 2/02 2/1/02 12:36 PM Page 8

SPEED DRYING PARTS

Parts and other materials can be speed dried

by waving the heated air stream over the

work until dried.

STRETCHING, SHAPING AND

INSTALLING VINYL

Direct hot air stream at vinyl section and

wave heat gun in a back and forth motion.

Stretch and shape until wrinkles are

removed. DO NOT aim at glass.

DEFROSTING FROZEN COILS OR PIPES

Direct hot air stream at frozen part and wave

back and forth until part is defrosted or

thawed.

LOOSENING NUTS AND BOLTS

Direct hot air stream at nut or bolt to be

loosened for a short period of time. Heating

the nut or bolt will cause the metal to

expand. Remove the air stream from work

piece. Loosen nut or bolt with proper wrench.

-9-

BM 2610615924 2/02 2/1/02 12:36 PM Page 9

Reflectors**

Concentrator**

Spreader**

(*= standard equipment)

(**= optional accessories)

Accessories

-10-

Service

Preventive maintenance

performed by unauth-

orized personnel may result in misplacing

of internal wires and components which

could cause serious hazard. We

recommend that all tool service be

performed by a Bosch Factory Service

Center or Authorized Bosch Service Station.

TOOL LUBRICATION

Your Bosch tool has been properly

lubricated and is ready to use. It is

recommended that tools with gears be

lubricated with Bosch lubricant at every

brush change.

CARBON BRUSHES

The brushes and commutator in your tool

have been engineered for many hours of

dependable service. To maintain peak

efficiency of the motor, we recommend

every two to six months the brushes be

examined. Only genuine Bosch replacement

brushes specially designed for your tool

should be used.

BEARINGS

Every second brush change, the bearings

should be replaced at Bosch Factory Service

Center or Authorized Bosch Service Station.

Bearings which become noisy should be

replaced at once to avoid overheating or

motor failure.

Cleaning

To avoid accidents always

disconnect the tool from

the power supply before cleaning or

performing any maintenance. The tool may

be cleaned most effectively with

compressed dry air. Always wear safety

goggles when cleaning tools with

compressed air.

Ventilation openings and switch levers must

be kept clean and free of foreign matter. Do

not attempt to clean by inserting pointed

objects through openings.

Certain cleaning agents

and solvents damage

plastic parts. Some of these are: gasoline,

carbon tetrachloride, chlorinated cleaning

solvents, ammonia and household

detergents that contain ammonia.

!

WARNING

Maintenance

!

WARNING

!

CAUTION

BM 2610615924 2/02 2/1/02 12:36 PM Page 10

Page is loading ...

2 610 615 924 2/02 Printed in U.S.A.

LIMITED WARRANTY OF BOSCH PORTABLE AND BENCHTOP POWER TOOLS

S-B Power Tool Company (“Seller”) warrants to the original purchaser only, that all BOSCH portable and benchtop power tools will be free from

defects in material or workmanship for a period of one year from date of purchase. SELLER’S SOLE OBLIGATION AND YOUR EXCLUSIVE REMEDY

under this Limited Warranty and, to the extent permitted by law, any warranty or condition implied by law, shall be the repair or replacement of

parts, without charge, which are defective in material or workmanship and which have not been misused, carelessly handled, or misrepaired by

persons other than Seller or Authorized Service Station. To make a claim under this Limited Warranty, you must return the complete portable or

benchtop power tool product, transportation prepaid, to any BOSCH Factory Service Center or Authorized Service Station. For Authorized BOSCH

Power Tool Service Stations, please refer to your phone directory.

THIS LIMITED WARRANTY DOES NOT APPLY TO ACCESSORY ITEMS SUCH AS CIRCULAR SAW BLADES, DRILL BITS, ROUTER BITS, JIGSAW

BLADES, SANDING BELTS, GRINDING WHEELS AND OTHER RELATED ITEMS.

ANY IMPLIED WARRANTIES SHALL BE LIMITED IN DURATION TO ONE YEAR FROM DATE OF PURCHASE. SOME STATES IN THE U.S., SOME

CANADIAN PROVINCES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT

APPLY TO YOU.

IN NO EVENT SHALL SELLER BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES (INCLUDING BUT NOT LIMITED TO LIABILITY

FOR LOSS OF PROFITS) ARISING FROM THE SALE OR USE OF THIS PRODUCT. SOME STATES IN THE U.S. AND SOME CANADIAN PROVINCES

DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR

EXCLUSION MAY NOT APPLY TO YOU.

THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO

STATE IN THE U.S., PROVINCE TO PROVINCE IN CANADA AND FROM COUNTRY TO COUNTRY.

THIS LIMITED WARRANTY APPLIES ONLY TO PORTABLE AND BENCHTOP ELECTRIC TOOLS SOLD WITHIN THE UNITED STATES OF AMERICA,

CANADA AND THE COMMONWEALTH OF PUERTO RICO. FOR WARRANTY COVERAGE WITHIN OTHER COUNTRIES, CONTACT YOUR LOCAL

BOSCH DEALER OR IMPORTER.

GARANTIE LIMITÉE DES OUTILS ÉLECTRIQUES PORTATIFS ET D'ÉTABLI BOSCH

S-B Power Tool Company (le « vendeur ») garantit à l'acheteur initial seulement que tous les outils électriques portatifs et d'établi BOSCH seront

exempts de vices de matériaux ou d'exécution pendant une période d'un an depuis la date d'achat. LA SEULE OBLIGATION DU VENDEUR ET LE

SEUL RECOURS DE L’ACHETEUR sous la présente garantie limitée, et en autant que la loi le permette sous toute garantie ou condition implicite qui

en découlerait, sera l’obligation de remplacer ou réparer gratuitement les pièces défectueuses matériellement ou comme fabrication, pourvu que

lesdites défectuosités ne soient pas attribuables à un usage abusif ou à quelque réparation bricolée par quelqu’un d’autre que le vendeur ou le

personnel d’une station-service agréée. Pour présenter une réclamation en vertu de cette garantie limitée, vous devez renvoyer l'outil électrique

portatif ou d'établi complet, port payé, à tout centre de service agréé ou centre de service usine. Veuillez consulter votre annuaire téléphonique

pour les adresses.

LA PRÉSENTE GARANTIE NE S’APPLIQUE PAS AUX ACCESSOIRES TELS QUE LAMES DE SCIES CIRCULAIRES, MÈCHES DE PERCEUSES, FERS

DE TOUPIES, LAMES DE SCIES SAUTEUSES, COURROIES DE PONÇAGE, MEULES ET AUTRES ARTICLES DU GENRE.

TOUTE GARANTIE IMPLICITE SERA LIMITÉE COMME DURÉE À UN AN À COMPTER DE LA DATE D’ACHAT. CERTAINS ÉTATS AMÉRICAINS,

CERTAINES PROVINCES CANADIENNES N’ADMETTANT PAS LE PRINCIPE DE LA LIMITATION DE LA DURÉE DES GARANTIES IMPLICITES, IL

EST POSSIBLE QUE LES LIMITATIONS CI-DESSUS NE S’APPLIQUENT PAS À VOTRE CAS.

EN AUCUN CAS LE VENDEUR NE SAURAIT ÊTRE TENU POUR RESPONSABLE DES INCIDENTS OU DOMMAGES INDIRECTS (INCLUANT, MAIS NE

SE LIMITANT PAS AUX PERTES DE PROFITS) CONSÉCUTIFS À LA VENTE OU L’USAGE DE CE PRODUIT. CERTAINS ÉTATS AMÉRICAINS ET

CERTAINES PROVINCES CANADIENNES N’ADMETTANT PAS LE PRINCIPE DE LA LIMITATION NI L’EXCLUSION DES DOMMAGES INDIRECTS ET

CONSÉQUENTIELS, IL EST POSSIBLE QUE LES LIMITATIONS OU EXCLUSIONS CI-DESSUS NE S’APPLIQUENT PAS À VOTRE CAS.

LA PRÉSENTE GARANTIE VOUS ACCORDE DES DROITS BIEN DÉTERMINÉS, Y COMPRIS POSSIBLEMENT CERTAINS DROITS VARIABLES DANS

LES DIFFÉRENTS ÉTATS AMÉRICAINS, PROVINCES CANADIENNES.

CETTE GARANTIE LIMITÉE NE S'APPLIQUE QU'AUX OUTILS ÉLECTRIQUES PORTATIFS ET D'ÉTABLI VENDUS AUX ÉTATS-UNIS D'AMÉRIQUE,

AU CANADA ET AU COMMONWEALTH DE PORTO RICO.POUR COUVERTURE DE GARANTIE DANS LES AUTRES PAYS, CONTACTEZ VOTRE

IMPORTATEUR OU REVENDEUR BOSCH LOCAL.

EXPORTADO POR: S.B. POWER TOOL COMPANY, CHICAGO, IL 60646, E.U.A.

IMPORTADO POR: ROBERT BOSCH S.A. DE C.V., CALLE ROBERT BOSCH NO. 405, ZONA

INDUSTRIAL TOLUCA, MÉXICO. C.P. 50070 TEL. (72) 792300

GARANTIA LIMITADA PARA HERRAMIENTAS MECANICAS PORTATILES Y PARA TABLERO DE BANCO BOSCH

S-B Power Tool Company ("el Vendedor") garantiza, únicamente al comprador original, que todas las herramientas mecánicas portátiles y para

tablero de banco BOSCH estarán libres de defectos de material o de fabricación durante un período de un año a partir de la fecha de compra. LA

UNICA OBLIGACION DEL VENDEDOR Y EL RECURSO EXCLUSIVO QUE USTED TIENE bajo esta Garantía Limitada y, hasta donde la ley lo permita,

bajo cualquier garantía o condición implícita por ley, consistirá en la reparación o sustitución sin costo de las piezas que presenten defectos de

material o de fabricación y que no hayan sido utilizadas incorrectamente, manejadas descuidadamente o reparadas incorrectamente por personas

que no sean el Vendedor o una Estación de servicio autorizada. Para efectuar una reclamación bajo esta Garantía Limitada, usted debe devolver el

producto, que consiste en la herramienta mecánica portátil o para tablero de banco completa, con el transporte pagado, a cualquier Centro de

servicio de fábrica o Estación de servicio autorizada. Para Estaciones de servicio autorizadas de herramientas mecánicas BOSCH, por favor,

consulte el directorio telefónico.

ESTA GARANTIA LIMITADA NO SE APLICA A ARTICULOS ACCESORIOS TALES COMO HOJAS PARA SIERRAS CIRCULARES, BROCAS PARA

TALADROS, BROCAS PARA FRESADORAS, HOJAS PARA SIERRAS DE VAIVEN, CORREAS PARA LIJAR, RUEDAS DE AMOLAR Y OTROS

ARTICULOS RELACIONADOS.

TODAS LAS GARANTIAS IMPLICITAS TENDRAN UNA DURACION LIMITADA A UN AÑO A PARTIR DE LA FECHA DE COMPRA. ALGUNOS

ESTADOS DE LOS EE.UU., ALGUNAS PROVINCIAS CANADIENSES NO PERMITEN LIMITACIONES EN CUANTO A LA DURACION DE UNA

GARANTIA IMPLICITA, POR LO QUE ES POSIBLE QUE LA LIMITACION ANTERIOR NO SEA APLICABLE EN EL CASO DE USTED.

EL VENDEDOR NO SERA RESPONSABLE EN NINGUN CASO DE NINGUN DAÑO INCIDENTAL O EMERGENTE (INCLUYENDO PERO NO LIMITADO A

RESPONSABILIDAD POR PERDIDA DE BENEFICIOS) QUE SE PRODUZCA COMO CONSECUENCIA DE LA VENTA O UTILIZACION DE ESTE

PRODUCTO. ALGUNOS ESTADOS DE LOS EE.UU. Y ALGUNAS PROVINCIAS CANADIENSES NO PERMITEN LA EXCLUSION O LIMITACION DE LOS

DAÑOS INCIDENTALES O EMERGENTES, POR LO QUE ES POSIBLE QUE LA LIMITACION O EXCLUSION ANTERIOR NO SEA APLICABLE EN EL

CASO DE USTED.

ESTA GARANTIA LIMITADA LE CONFIERE A USTED DERECHOS LEGALES ESPECIFICOS Y ES POSIBLE QUE USTED TAMBIEN TENGA OTROS

DERECHOS QUE VARIAN DE ESTADO A ESTADO EN LOS EE.UU., DE PROVINCIA A PROVINCIA EN CANADA.

ESTA GARANTIA LIMITADA SE APLICA SOLAMENTE A HERRAMIENTAS ELECTRICAS PORTATILES Y PARA TABLERO DE BANCO VENDIDAS EN

LOS ESTADOS UNIDOS DE AMERICA, CANADA Y EL ESTADO LIBRE ASOCIADO DE PUERTO RICO. PARA COBERTURA DE GARANTIA EN OTROS

PAISES, PONGASE EN CONTACTO CON SU DISTRIBUIDOR O IMPORTADOR LOCAL DE BOSCH.

BM 2610615924 2/02 2/1/02 12:36 PM Page 32

Bosch Power Tools 1942 User manual

Bosch Power Tools 1942 User manual

in other languages

Related papers

Other documents