Makita LCT309W User guide

1

INSTRUCTION MANUAL

MANUEL D'INSTRUCTION

MANUAL DE INSTRUCCIONES

IMPORTANT: Read Before Using.

IMPORTANT: Lire avant usage.

IMPORTANTE: Leer antes de usar.

Cordless Driver Drill

Perceuse-visseuse sans fil

Atornillador-Taladro Inalámbrico

FD02

009329

2

ENGLISH (Original instructions)

SPECIFICATIONS

Model FD02

Steel 10 mm (3/8")

Wood 21 mm (13/16")

Wood screw 5.1 mm x 63 mm (7/32" X 2-1/2")

Capacities

Machine screw M6 (1/4")

High (2) 0 - 1,300/min.

No load speed (RPM)

Low (1) 0 - 350/min.

Chuck capacity 0.8 mm (1/32") - 10 mm (3/8")

Overall length 189 mm (7-7/16")

Net weight 1.0 kg (2.2 lbs)

Rated voltage D.C. 10.8 V / 12 V max

Standard battery cartridge BL1014

• Due to our continuing programme of research and development, the specifications herein are subject to change without notice.

• Specifications and battery cartridge may differ from country to country.

• Weight, with battery cartridge, according to EPTA-Procedure 01/2003

GEA006-2

General Power Tool Safety

Warnings

WARNING Read all safety warnings and all

instructions. Failure to follow the warnings and

instructions may result in electric shock, fire and/or

serious injury.

Save all warnings and

instructions for future reference.

The term "power tool" in the warnings refers to your

mains-operated (corded) power tool or battery-operated

(cordless) power tool.

Work area safety

1. Keep work area clean and well lit. Cluttered or

dark areas invite accidents.

2. Do not operate power tools in explosive

atmospheres, such as in the presence of

flammable liquids, gases or dust. Power tools

create sparks which may ignite the dust or fumes.

3. Keep children and bystanders away while

operating a power tool. Distractions can cause

you to lose control.

Electrical Safety

4. Power tool plugs must match the outlet. Never

modify the plug in any way. Do not use any

adapter plugs with earthed (grounded) power

tools. Unmodified plugs and matching outlets will

reduce risk of electric shock.

5. Avoid body contact with earthed or grounded

surfaces such as pipes, radiators, ranges and

refrigerators. There is an increased risk of

electric shock if your body is earthed or grounded.

6. Do not expose power tools to rain or wet

conditions. Water entering a power tool will

increase the risk of electric shock.

7. Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool.

Keep cord away from heat, oil, sharp edges or

moving parts. Damaged or entangled cords

increase the risk of electric shock.

8. When operating a power tool outdoors, use an

extension cord suitable for outdoor use. Use of

a cord suitable for outdoor use reduces the risk of

electric shock.

9. If operating a power tool in a damp location is

unavoidable, use a ground fault circuit

interrupter (GFCI) protected supply. Use of an

GFCI reduces the risk of electric shock.

Personal Safety

10. Stay alert, watch what you are doing and use

common sense when operating a power tool.

Do not use a power tool while you are tired or

under the influence of drugs, alcohol or

medication. A moment of inattention while

operating power tools may result in serious

personal injury.

11. Use personal protective equipment. Always

wear eye protection. Protective equipment such

as dust mask, non-skid safety shoes, hard hat, or

hearing protection used for appropriate conditions

will reduce personal injuries.

12. Prevent unintentional starting. Ensure the

switch is in the off-position before connecting

to power source and/or battery pack, picking

up or carrying the tool. Carrying power tools with

your finger on the switch or energising power tools

3

that have the switch on invites accidents.

13. Remove any adjusting key or wrench before

turning the power tool on. A wrench or a key left

attached to a rotating part of the power tool may

result in personal injury.

14. Do not overreach. Keep proper footing and

balance at all times. This enables better control

of the power tool in unexpected situations.

15. Dress properly. Do not wear loose clothing or

jewellery. Keep your hair, clothing, and gloves

away from moving parts. Loose clothes,

jewellery or long hair can be caught in moving

parts.

16. If devices are provided for the connection of

dust extraction and collection facilities,

ensure these are connected and properly used.

Use of dust collection can reduce dust-related

hazards.

Power tool use and care

17. Do not force the power tool. Use the correct

power tool for your application. The correct

power tool will do the job better and safer at the

rate for which it was designed.

18. Do not use the power tool if the switch does

not turn it on and off. Any power tool that cannot

be controlled with the switch is dangerous and

must be repaired.

19. Disconnect the plug from the power source

and/or the battery pack from the power tool

before making any adjustments, changing

accessories, or storing power tools. Such

preventive safety measures reduce the risk of

starting the power tool accidentally.

20. Store idle power tools out of the reach of

children and do not allow persons unfamiliar

with the power tool or these instructions to

operate the power tool. Power tools are

dangerous in the hands of untrained users.

21. Maintain power tools. Check for misalignment

or binding of moving parts, breakage of parts

and any other condition that may affect the

power tool’s operation. If damaged, have the

power tool repaired before use. Many accidents

are caused by poorly maintained power tools.

22. Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges

are less likely to bind and are easier to control.

23. Use the power tool, accessories and tool bits

etc. in accordance with these instructions,

taking into account the working conditions

and the work to be performed. Use of the power

tool for operations different from those intended

could result in a hazardous situation.

Battery tool use and care

24. Recharge only with the charger specified by

the manufacturer. A charger that is suitable for

one type of battery pack may create a risk of fire

when used with another battery pack.

25. Use power tools only with specifically

designated battery packs. Use of any other

battery packs may create a risk of injury and fire.

26. When battery pack is not in use, keep it away

from other metal objects, like paper clips,

coins, keys, nails, screws or other small metal

objects, that can make a connection from one

terminal to another. Shorting the battery

terminals together may cause burns or a fire.

27. Under abusive conditions, liquid may be

ejected from the battery; avoid contact. If

contact accidentally occurs, flush with water.

If liquid contacts eyes, additionally seek

medical help. Liquid ejected from the battery may

cause irritation or burns.

Service

28. Have your power tool serviced by a qualified

repair person using only identical replacement

parts. This will ensure that the safety of the power

tool is maintained.

29. Follow instruction for lubricating and

changing accessories.

30. Keep handles dry, clean and free from oil and

grease.

USB102-1

CORDLESS DRILL SAFETY

WARNINGS

1. Use auxiliary handles supplied with the tool.

Loss of control can cause personal injury. (if

supplied)

2. Hold power tools by insulated gripping

surfaces when performing an operation where

the cutting tool may contact hidden wiring or

its own cord. Contact with a "live" wire will make

exposed metal parts of the tool "live" and shock

the operator.

3. Hold power tool by insulated gripping

surfaces, when performing an operation

where the fastener may contact hidden wiring

or its own cord. Fasteners contacting a "live" wire

may make exposed metal parts of the power tool

"live" and could give the operator an electric

shock.

4. Always be sure you have a firm footing.

Be sure no one is below when using the tool in

high locations.

5. Hold the tool firmly.

6. Keep hands away from rotating parts.

4

7. Do not leave the tool running. Operate the tool

only when hand-held.

8. Do not touch the drill bit or the workpiece

immediately after operation; they may be

extremely hot and could burn your skin.

9. Some material contains chemicals which may

be toxic. Take caution to prevent dust

inhalation and skin contact. Follow material

supplier safety data.

SAVE THESE INSTRUCTIONS.

WARNING:

DO NOT let comfort or familiarity with product

(gained from repeated use) replace strict adherence

to safety rules for the subject product. MISUSE or

failure to follow the safety rules stated in this

instruction manual may cause serious personal

injury.

USD301-1

Symbols

The followings show the symbols used for tool.

･ volts

･ direct current

･ no load speed

･ revolutions or reciprocation per minute

ENC007-5

IMPORTANT SAFETY

INSTRUCTIONS

FOR BATTERY CARTRIDGE

1. Before using battery cartridge, read all

instructions and cautionary markings on (1)

battery charger, (2) battery, and (3) product

using battery.

2. Do not disassemble battery cartridge.

3. If operating time has become excessively

shorter, stop operating immediately. It may

result in a risk of overheating, possible burns

and even an explosion.

4. If electrolyte gets into your eyes, rinse them

out with clear water and seek medical

attention right away. It may result in loss of

your eyesight.

5. Do not short the battery cartridge:

(1) Do not touch the terminals with any

conductive material.

(2) Avoid storing battery cartridge in a

container with other metal objects such as

nails, coins, etc.

(3) Do not expose battery cartridge to water

or rain.

A battery short can cause a large current

flow, overheating, possible burns and

even a breakdown.

6. Do not store the tool and battery cartridge in

locations where the temperature may reach or

exceed 50 ﾟ C (122 ﾟ F).

7. Do not incinerate the battery cartridge even if

it is severely damaged or is completely worn

out. The battery cartridge can explode in a fire.

8. Be careful not to drop or strike battery.

9. Do not use a damaged battery.

SAVE THESE INSTRUCTIONS.

Tips for maintaining maximum battery life

1. Charge the battery cartridge before

completely discharged.

Always stop tool operation and charge the

battery cartridge when you notice less tool

power.

2. Never recharge a fully charged battery

cartridge.

Overcharging shortens the battery service life.

3. Charge the battery cartridge with room

temperature at 10 ﾟ C - 40 ﾟ C (50 ﾟ F - 104 ﾟ F).

Let a hot battery cartridge cool down before

charging it.

FUNCTIONAL DESCRIPTION

CAUTION:

• Always be sure that the tool is switched off and the

battery cartridge is removed before adjusting or

checking function on the tool.

Installing or removing battery cartridge

1

2

009330

•

Always switch off the tool before insertion or

removal of the battery cartridge.

• To remove the battery cartridge, withdraw it from

the tool while pressing the buttons on both sides of

the cartridge.

• To insert the battery cartridge, hold it so that the

battery cartridge front shape fits to that of the

battery installment opening and slip it into place.

1. Button

2. Battery cartridge

5

Always insert it all the way until it locks in place with

a little click. If not, it may accidentally fall out of the

tool, causing injury to you or someone around you.

• Do not use force when inserting the battery

cartridge. If the cartridge does not slide in easily, it

is not being inserted correctly.

Switch action

1

009336

CAUTION:

• Before inserting the battery cartridge into the tool,

always check to see that the switch trigger actuates

properly and returns to the "OFF" position when

released.

To start the tool, simply pull the switch trigger. Tool speed

is increased by increasing pressure on the switch trigger.

Release the switch trigger to stop.

Electric brake

This tool is equipped with an electric brake. If the tool

consistently fails to quickly stop after switch trigger

release, have tool serviced at a Makita service center.

Turning on the front lamp

1

009332

CAUTION:

• Do not look in the light or see the source of the light

directly.

Pull the switch trigger to turn on the light. The lamp keeps

on lighting while the switch trigger is being pulled. The

lamp turns off 10 -15 seconds after releasing the trigger.

NOTE:

• Use a dry cloth to wipe the dirt off the lens of lamp.

Be careful not to scratch the lens of lamp, or it may

lower the illumination.

Reversing switch action

A

B

1

008802

This tool has a reversing switch to change the direction of

rotation. Depress the reversing switch lever from the A

side for clockwise rotation or from the B side for

counterclockwise rotation.

When the reversing switch lever is in the neutral position,

the switch trigger cannot be pulled.

CAUTION:

• Always check the direction of rotation before

operation.

• Use the reversing switch only after the tool comes

to a complete stop. Changing the direction of

rotation before the tool stops may damage the tool.

• When not operating the tool, always set the

reversing switch lever to the neutral position.

Speed change

1

008803

To change the speed, first switch off the tool and then

slide the speed change lever to the "2" side for high

speed or "1" side for low speed. Be sure that the speed

change lever is set to the correct position before

operation. Use the right speed for your job.

CAUTION:

• Always set the speed change lever fully to the

correct position. If you operate the tool with the

speed change lever positioned halfway between

the "1" side and "2" side, the tool may be damaged.

• Do not use the speed change lever while the tool is

running. The tool may be damaged.

1. Speed change

lever

1. Reversing switch

lever

1. Lamp

1. Switch trigger

6

Adjusting the fastening torque

1

2

3

009333

The fastening torque can be adjusted in 18 steps by

turning the adjusting ring so that its graduations are

aligned with the pointer on the tool body. The fastening

torque is minimum when the number 1 is aligned with the

pointer, and maximum when the

marking is aligned

with the pointer.

The clutch will slip at various torque levels when set at

the number 1 to 18. The clutch is designed not to slip at

the

marking.

Before actual operation, drive a trial screw into your

material or a piece of duplicate material to determine

which torque level is required for a particular application.

ASSEMBLY

CAUTION:

• Always be sure that the tool is switched off and the

battery cartridge is removed before carrying out

any work on the tool.

Installing or removing driver bit or drill bit

1

009331

Turn the sleeve counterclockwise to open the chuck jaws.

Place the bit in the chuck as far as it will go. Turn the

sleeve clockwise to tighten the chuck.

To remove the bit, turn the sleeve counterclockwise.

OPERATION

CAUTION:

• Always insert the battery cartridge all the way until it

locks in place. If not, it may accidentally fall out of

the tool, causing injury to you or someone around

you.

Hold the tool firmly with one hand on the grip and the

other hand on the bottom of the battery cartridge to

control the twisting action.

Screwdriving operation

009334

CAUTION:

• Adjust the adjusting ring to the proper torque level

for your work.

Place the point of the driver bit in the screw head and

apply pressure to the tool. Start the tool slowly and then

increase the speed gradually. Release the switch trigger

as soon as the clutch cuts in.

CAUTION:

• Make sure that the driver bit is inserted straight in

the screw head, or the screw and/or bit may be

damaged.

NOTE:

• When driving wood screws, predrill pilot holes to

make driving easier and to prevent splitting of the

workpiece. See the chart.

4.2 - 4.4 (11/64” - 11/64”)

Nominal diameter of wood screw

(mm)

3.1 (1/8”)

3.5 (9/64”)

3.8 (5/32”)

4.5 (11/64”)

4.8 (3/16”)

5.1 (13/64”)

5.5 (7/32”)

5.8 (7/32”)

6.1 (15/64”)

Recommended size of pilot hole

(mm)

2.0 - 2.2 (5/64” - 3/32”)

2.2 - 2.5 (3/32” - 3/32”)

2.5 - 2.8 (3/32” - 7/64”)

2.9 - 3.2 (7/64” - 1/8”)

3.1 - 3.4 (1/8” - 9/64”)

3.3 - 3.6 (1/8” - 9/64”)

3.7 - 3.9 (9/64” - 5/32”)

4.0 - 4.2 (5/32” - 11/64”)

001904

Drilling operation

First, turn the adjusting ring so that the pointer points to

the

marking. Then proceed as follows.

Drilling in wood

When drilling in wood, the best results are obtained with

wood drills equipped with a guide screw. The guide

screw makes drilling easier by pulling the bit into the

workpiece.

Drilling in metal

To prevent the bit from slipping when starting a hole,

make an indentation with a center-punch and hammer at

1. Sleeve

1. Pointer

2. Adjusting ring

3. Graduation

7

the point to be drilled. Place the point of the bit in the

indentation and start drilling.

Use a cutting lubricant when drilling metals. The

exceptions are iron and brass which should be drilled dry.

CAUTION:

• Pressing excessively on the tool will not speed up

the drilling. In fact, this excessive pressure will only

serve to damage the tip of your bit, decrease the

tool performance and shorten the service life of the

tool.

• There is a tremendous force exerted on the tool/bit

at the time of hole break through. Hold the tool

firmly and exert care when the bit begins to break

through the workpiece.

• A stuck bit can be removed simply by setting the

reversing switch to reverse rotation in order to back

out. However, the tool may back out abruptly if you

do not hold it firmly.

• Always secure small workpieces in a vise or similar

hold-down device.

• If the tool is operated continuously until the battery

cartridge has discharged, allow the tool to rest for

15 minutes before proceeding with a fresh battery.

Using the tool as a hand screwdriver

009335

Switch off the tool.

Move the lock button to the locked position A.

Turn the tool.

NOTE:

• This use is convenient for checking the

screwdriving.

• Do not use the tool for work requiring excessive

force, such as tightening bolt or removing rusted

screws.

Using holster

CAUTION:

• Do not use for tools such as a drill with a bit

installed on them.

• Turn off a tool and wait until it comes to a complete

stop before placing in the holster.

Be sure to close the holster securely so that it holds

the tool firmly.

Thread a waist belt or similar through holster holder.

Put the tool in the holster and lock it with the holster

button.

008807

008808

Two bits can be retained at the front of holster.

008809

MAINTENANCE

CAUTION:

• Always be sure that the tool is switched off and the

battery cartridge is removed before attempting to

perform inspection or maintenance.

• Never use gasoline, benzine, thinner, alcohol or the

like. Discoloration, deformation or cracks may

result.

To maintain product SAFETY and RELIABILITY, repairs,

any other maintenance or adjustment should be

performed by Makita Authorized or Factory Service

Centers, always using Makita replacement parts.

8

ACCESSORIES

CAUTION:

• These accessories or attachments are

recommended for use with your Makita tool

specified in this manual. The use of any other

accessories or attachments might present a risk of

injury to persons. Only use accessory or

attachment for its stated purpose.

If you need any assistance for more details regarding

these accessories, ask your local Makita Service Center.

• Drill bits

• Screw bits

• Socket bits

• Various type of Makita genuine batteries and

chargers

• Holster

• Plastic carrying case

MAKITA LIMITED ONE YEAR WARRANTY

Warranty Policy

Every Makita tool is thoroughly inspected and tested

before leaving the factory. It is warranted to be free of

defects from workmanship and materials for the period

of ONE YEAR from the date of original purchase.

Should any trouble develop during this one year period,

return the COMPLETE tool, freight prepaid, to one of

Makita’s Factory or Authorized Service Centers. If

inspection shows the trouble is caused by defective

workmanship or material, Makita will repair (or at our

option, replace) without charge.

This Warranty does not apply where:

IN NO EVENT SHALL MAKITA BE LIABLE FOR ANY

INDIRECT, INCIDENTAL OR CONSEQUENTIAL

DAMAGES FROM THE SALE OR USE OF THE

PRODUCT. THIS DISCLAIMER APPLIES BOTH

DURING AND AFTER THE TERM OF THIS

WARRANTY.

MAKITA DISCLAIMS LIABILITY FOR ANY IMPLIED

WARRANTIES, INCLUDING IMPLIED WARRANTIES

OF "MERCHANTABILITY" AND "FITNESS FOR A

SPECIFIC PURPOSE," AFTER THE ONE YEAR TERM

OF THIS WARRANTY.

This Warranty gives you specific legal rights, and you

may also have other rights which vary from state to

state. Some states do not allow the exclusion or

limitation of incidental or consequential damages, so

the above limitation or exclusion may not apply to you.

Some states do not allow limitation on how long an

implied warranty lasts, so the above limitation may not

apply to you.

repairs have been made or attempted by others:

repairs are required because of normal wear and

tear:

the tool has been abused, misused or improperly

maintained:

alterations have been made to the tool.

EN0006-1

Page is loading ...

28

Some dust created by power sanding, sawing, grinding, drilling, and other

construction activities contains chemicals known to the State of California

to cause cancer, birth defects or other reproductive harm. Some examples

of these chemicals are:

• lead from lead-based paints,

• crystalline silica from bricks and cement and other masonry products, and

• arsenic and chromium from chemically-treated lumber.

Your risk from these exposures varies, depending on how often you do this

type of work. To reduce your exposure to these chemicals: work in a well

ventilated area, and work with approved safety equipment, such as those

dust masks that are specially designed to filter out microscopic particles.

WARNING

< USA only >

ADVERTENCIA

Algunos tipos de polvo creados por el lijado, serrado, amolado, taladrado, y

otras actividades de la construccion contienen sustancias quimicas

reconocidas por el Estado de California como causantes de cancer, defectos

de nacimiento y otros peligros de reproduccion. Algunos ejemplos de estos

productos quimicos son:

• plomo de pinturas a base de plomo,

• silice cristalino de ladrillos y cemento y otros productos de albanileria, y

• arsenico y cromo de maderas tratadas quimicamente.

El riesgo al que se expone variara, dependiendo de la frecuencia con la que

realice este tipo de trabajo. Para reducir la exposicion a estos productos

quimicos: trabaje en un area bien ventilada, y pongase el equipo de seguridad

indicado, tal como esas mascaras contra el polvo que estan especialmente

disenadas para filtrar particulas microscopicas.

< USA solamente >

Makita Corporation

3-11-8, Sumiyoshi-cho,

Anjo, Aichi 446-8502 Japan

www.makita.com

884867A937 FD02-1

Rechargeable Flashlight

Instruction manual

Lampe torche

Manuel d’instructions

Linterna recargable

Manual de instrucciones

LM01

Page is loading ...

3

ENGLISH

Explanation of general view

SPECIFICATIONS

• Due to our continuing programme of research and development, the specifications herein are subject to change without

notice.

• Note: Specifications may differ from country to country.

IMPORTANT SAFETY

INSTRUCTIONS

WARNING:

When using electric tools, basic safety precautions should

always be followed to reduce the risk of fire, electric

shock, and personal injury, including the following:

READ ALL INSTRUCTIONS.

1. Read this instruction manual and the charger

instruction manual carefully before use.

2. This light is not waterproof. Do not use it in damp or

wet locations. Do not expose it to rain or snow. Do not

wash it in water.

3. A short-circuit can cause a large current flow,

overheating, possible burns and even a breakdown.

(1) Do not touch the inside of the light with tweezers,

metal tools, etc.

(2) Do not touch the battery terminals with any

conductive material.

(3) Avoid storing the battery cartridge in a container

with any metal objects such as nails, coins, etc.

4. Never expose the battery cartridge to flames, fire or

great heat. Breakage may cause release of injurious

material.

5. If electrolyte gets into your eyes, rinse them out with

clear water and seek medical attention right away. It

may result in loss of your eyesight.

6. If operating time has become excessively shorter, stop

operating immediately. It may result in a risk of

overheating, possible burns and even an explosion.

7. Be careful not to drop, shake or strike battery.

8. When the tool is not in use, always switch off and

remove the battery cartridge from the tool.

9. Do not store the tool and battery cartridge in locations

where the temperature may reach or exceed 50°C

(122°F).

10. Do not give the tool a shock by dropping, striking, etc.

11. Do not expose the light to eyes continuously. It may

hurt them.

12. Do not cover or clog the lit tool with cloth or carton,

etc. It may create a risk of fire.

13. Do not disassemble the charger or battery cartridge;

take it to a qualified serviceman when service or repair

is required. Incorrect reassembly may result in a risk

of electric shock or fire.

14. If any problem develops, consult your nearest Makita

Service Center or dealer. To maintain product safety

and reliability, repairs, maintenance or adjustment

should be carried out by Makita Authorized Service

Center.

SAVE THESE INSTRUCTIONS.

FUNCTIONAL DESCRIPTION

CAUTION:

1. SAVE THESE INSTRUCTIONS - This manual

contains important safety and operating instructions

for battery charger.

2. Before using battery charger, read all instructions and

cautionary markings on (1) battery charger, (2) battery,

and (3) product using battery.

3. CAUTION - To reduce risk of injury, charge only

MAKITA rechargeable batteries. Other types of

batteries may burst causing personal injury and

damage.

4. Non-rechargeable batteries cannot be charged with

this battery charger.

5. Use a power source with the voltage specified on the

nameplate of the charger.

6. Do not charge the battery cartridge in presence of

flammable liquids or gases.

7. Do not expose charger to rain or snow.

8. Never carry charger by cord or yank it to disconnect

from receptacle.

9. After charging or before attempting any maintenance

or cleaning, unplug the charger from the power

source. Pull by plug rather than cord whenever

disconnecting charger.

1. Charging light

2. Button

3. Battery cartridge

4. Switch

5. Light

6. Clip

Model LM01

Power source D.C 10.8 V/12 V max.

LED 1 W

Operating time Approx. 9 hours (BL1014)

Charging time Approx. 50 min (DC10WB)

Dimensions (With battery cartridge Without flexible leg)

119 mm (4-11/16") (L) x 52 mm (2-1/16") (W) x

55 mm (2-3/16") (H)

Net weight (With battery cartridge) 0.25 Kg (0.6 lbs)

4

10. Make sure cord is located so that it will not be stepped

on, tripped over, or otherwise subjected to damage or

stress.

11. Do not operate charger with damaged cord or plug -

replace them immediately.

12. Do not operate or disassemble charger if it has

received a sharp blow, been dropped, or otherwise

damaged in any way; take it to a qualified serviceman.

Incorrect use or reassembly may result in a risk of

electric shock or fire.

13. The battery charger is not intended for use by young

children or infirm persons without supervision.

14. Young children should be supervised to ensure that

they do not play with the battery charger.

15. Do not charge battery cartridge when temperature is

BELOW 10°C (50°F) or ABOVE 40°C (104°F).

16. Do not attempt to use a step-up transformer, an

engine generator or DC power receptacle.

Charging (Fig. 1)

Charge the battery cartridge with the Makita charger

before use.

1. Plug the battery charger into the proper AC voltage

source. The charging light will flash in green color.

2. Insert the battery cartridge so that the plus and minus

terminals on the battery cartridge are on the same

sides as their respective markings on the charger.

3. When the battery cartridge is inserted fully, the

charging light will change from green to red and

charging will begin. The charging light will remain lit

steadily during charging.

4. When the charging light changes from red to green,

the charging cycle is complete.

5. After charging, unplug the charger from the power

source.

NOTE:

• The battery charger is for charging Makita battery

cartridge. Never use it for other purposes or for other

manufacturer's batteries.

• If you charge a battery cartridge from a just operated

tool or a battery cartridge which has been exposed to

direct sunlight or heat for a long time, the charging light

may flash in red color. If this occurs, wait for a while.

Charging will begin after the battery cartridge cools.

• If the charging light flashes alternately in green and

red, charging is not possible. The terminals on the

charger or battery cartridge are clogged with dust or

the battery cartridge is worn out or damaged.

CAUTION:

• Always be sure that the tool is switched off and the

battery cartridge is removed before adjusting or

checking function on the tool.

Installing or removing battery cartridge

(Fig. 2)

• Always switch off the tool before insertion or removal of

the battery cartridge.

• To remove the battery cartridge, withdraw it from the

tool while pressing the buttons on both sides of the

cartridge.

• To insert the battery cartridge, align the tongue on the

battery cartridge with the groove in the housing and slip

it into place. Always insert it all the way until it locks in

place with a little click. If not, it may accidentally fall out

of the tool, causing injury to you or someone around

you.

• Do not use force when inserting the battery cartridge. If

the cartridge does not slide in easily, it is not being

inserted correctly.

Lighting up the lamp (Fig. 3)

CAUTION:

• Do not look in the light or see the source of light

directly.

• Push the switch to light up the light. To turn off, push

the switch again.

NOTE:

• When remaining battery capacity becomes lower,

light turns off automatically. So you should charge

the battery cartridge soon.

• Operating time may be shortened according to

environments and battery conditions.

OPERATION

Clip (Fig. 4)

User can carry the light with hands free by hooking the

clip on a belt.

MAINTENANCE

CAUTION:

Always be sure that the cleaner is switched off before

carrying out any work on the cleaner.

To maintain product safety and reliability, repairs,

maintenance or adjustment should be carried out by a

Makita Authorized Service Center.

ACCESSORIES

CAUTION:

These accessories or attachments are recommended for

use with your Makita tool specified in this manual. The use

of any other accessories or attachments might present a

risk of injury to persons. Only use accessory or

attachment for its stated purpose. If you need any

assistance for more details regarding these accessories,

ask your local Makita service center.

• Battery Charger

• Battery Cartridge

Page is loading ...

ALA

Makita Corporation

3-11-8, Sumiyoshi-cho,

Anjo, Aichi 446-8502 Japan

884858-938

www.makita.com

1

INSTRUCTION MANUAL

MANUEL D'INSTRUCTION

MANUAL DE INSTRUCCIONES

IMPORTANT: Read Before Using.

IMPORTANT: Lire avant usage.

IMPORTANTE: Leer antes de usar.

Cordless Impact Wrench

Boulonneuse sans Fil

Llave de Impacto Inalámbrica

WT01

011762

2

ENGLISH (Original instructions)

SPECIFICATIONS

Model WT01

Standard bolt M8 - M12 (5/16" - 1/2")

Capacities

High tensile bolt M6 - M10 (1/4" - 3/8")

Square drive 9.5 mm (3/8")

No load speed (RPM) 0 -2,300/min.

Impacts per minute 0 - 3,000

Max. fastening torque 110 N.m (1,000 in.lbs)

Overall length 163 mm (6-3/8")

Net weight 0.95 kg (2.1 lbs)

Rated voltage D.C. 10.8V/12Vmax

Standard battery cartridges BL1014

• Due to our continuing programme of research and development, the specifications herein are subject to change without notice.

• Specifications and battery cartridge may differ from country to country.

• Weight, with battery cartridge, according to EPTA-Procedure 01/2003

GEA006-2

General Power Tool Safety

Warnings

WARNING Read all safety warnings and all

instructions. Failure to follow the warnings and

instructions may result in electric shock, fire and/or

serious injury.

Save all warnings and

instructions for future reference.

The term "power tool" in the warnings refers to your

mains-operated (corded) power tool or battery-operated

(cordless) power tool.

Work area safety

1. Keep work area clean and well lit. Cluttered or

dark areas invite accidents.

2. Do not operate power tools in explosive

atmospheres, such as in the presence of

flammable liquids, gases or dust. Power tools

create sparks which may ignite the dust or fumes.

3. Keep children and bystanders away while

operating a power tool. Distractions can cause

you to lose control.

Electrical Safety

4. Power tool plugs must match the outlet. Never

modify the plug in any way. Do not use any

adapter plugs with earthed (grounded) power

tools. Unmodified plugs and matching outlets will

reduce risk of electric shock.

5. Avoid body contact with earthed or grounded

surfaces such as pipes, radiators, ranges and

refrigerators. There is an increased risk of

electric shock if your body is earthed or grounded.

6. Do not expose power tools to rain or wet

conditions. Water entering a power tool will

increase the risk of electric shock.

7. Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool.

Keep cord away from heat, oil, sharp edges or

moving parts. Damaged or entangled cords

increase the risk of electric shock.

8. When operating a power tool outdoors, use an

extension cord suitable for outdoor use. Use of

a cord suitable for outdoor use reduces the risk of

electric shock.

9. If operating a power tool in a damp location is

unavoidable, use a ground fault circuit

interrupter (GFCI) protected supply. Use of an

GFCI reduces the risk of electric shock.

Personal Safety

10. Stay alert, watch what you are doing and use

common sense when operating a power tool.

Do not use a power tool while you are tired or

under the influence of drugs, alcohol or

medication. A moment of inattention while

operating power tools may result in serious

personal injury.

11. Use personal protective equipment. Always

wear eye protection. Protective equipment such

as dust mask, non-skid safety shoes, hard hat, or

hearing protection used for appropriate conditions

will reduce personal injuries.

12. Prevent unintentional starting. Ensure the

switch is in the off-position before connecting

to power source and/or battery pack, picking

up or carrying the tool. Carrying power tools with

your finger on the switch or energising power tools

that have the switch on invites accidents.

3

13. Remove any adjusting key or wrench before

turning the power tool on. A wrench or a key left

attached to a rotating part of the power tool may

result in personal injury.

14. Do not overreach. Keep proper footing and

balance at all times. This enables better control

of the power tool in unexpected situations.

15. Dress properly. Do not wear loose clothing or

jewellery. Keep your hair, clothing, and gloves

away from moving parts. Loose clothes,

jewellery or long hair can be caught in moving

parts.

16. If devices are provided for the connection of

dust extraction and collection facilities,

ensure these are connected and properly used.

Use of dust collection can reduce dust-related

hazards.

Power tool use and care

17. Do not force the power tool. Use the correct

power tool for your application. The correct

power tool will do the job better and safer at the

rate for which it was designed.

18. Do not use the power tool if the switch does

not turn it on and off. Any power tool that cannot

be controlled with the switch is dangerous and

must be repaired.

19. Disconnect the plug from the power source

and/or the battery pack from the power tool

before making any adjustments, changing

accessories, or storing power tools. Such

preventive safety measures reduce the risk of

starting the power tool accidentally.

20. Store idle power tools out of the reach of

children and do not allow persons unfamiliar

with the power tool or these instructions to

operate the power tool. Power tools are

dangerous in the hands of untrained users.

21. Maintain power tools. Check for misalignment

or binding of moving parts, breakage of parts

and any other condition that may affect the

power tool’s operation. If damaged, have the

power tool repaired before use. Many accidents

are caused by poorly maintained power tools.

22. Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges

are less likely to bind and are easier to control.

23. Use the power tool, accessories and tool bits

etc. in accordance with these instructions,

taking into account the working conditions

and the work to be performed. Use of the power

tool for operations different from those intended

could result in a hazardous situation.

Battery tool use and care

24. Recharge only with the charger specified by

the manufacturer. A charger that is suitable for

one type of battery pack may create a risk of fire

when used with another battery pack.

25. Use power tools only with specifically

designated battery packs. Use of any other

battery packs may create a risk of injury and fire.

26. When battery pack is not in use, keep it away

from other metal objects, like paper clips,

coins, keys, nails, screws or other small metal

objects, that can make a connection from one

terminal to another. Shorting the battery

terminals together may cause burns or a fire.

27. Under abusive conditions, liquid may be

ejected from the battery; avoid contact. If

contact accidentally occurs, flush with water.

If liquid contacts eyes, additionally seek

medical help. Liquid ejected from the battery may

cause irritation or burns.

Service

28. Have your power tool serviced by a qualified

repair person using only identical replacement

parts. This will ensure that the safety of the power

tool is maintained.

29. Follow instruction for lubricating and

changing accessories.

30. Keep handles dry, clean and free from oil and

grease.

GEB049-2

CORDLESS IMPACT WRENCH

SAFETY WARNINGS

1. Hold power tool by insulated gripping

surfaces, when performing an operation

where the fastener may contact hidden wiring.

Fasteners contacting a "live" wire may make

exposed metal parts of the power tool "live" and

could give the operator an electric shock.

2. Wear ear protectors.

3. Check the socket carefully for wear, cracks or

damage before installation.

4. Hold the tool firmly.

5. Always be sure you have a firm footing.

Be sure no one is below when using the tool in

high locations.

6. The proper fastening torque may differ

depending upon the kind or size of the bolt.

Check the torque with a torque wrench.

SAVE THESE INSTRUCTIONS.

4

WARNING:

DO NOT let comfort or familiarity with product

(gained from repeated use) replace strict adherence

to safety rules for the subject product. MISUSE or

failure to follow the safety rules stated in this

instruction manual may cause serious personal

injury.

USD302-1

Symbols

The followings show the symbols used for tool.

･ volts

･ direct current

･ no load speed

･ revolutions or reciprocation per minute

･ number of blow

ENC007-7

IMPORTANT SAFETY

INSTRUCTIONS

FOR BATTERY CARTRIDGE

1. Before using battery cartridge, read all

instructions and cautionary markings on (1)

battery charger, (2) battery, and (3) product

using battery.

2. Do not disassemble battery cartridge.

3. If operating time has become excessively

shorter, stop operating immediately. It may

result in a risk of overheating, possible burns

and even an explosion.

4. If electrolyte gets into your eyes, rinse them

out with clear water and seek medical

attention right away. It may result in loss of

your eyesight.

5. Do not short the battery cartridge:

(1) Do not touch the terminals with any

conductive material.

(2) Avoid storing battery cartridge in a

container with other metal objects such as

nails, coins, etc.

(3) Do not expose battery cartridge to water

or rain.

A battery short can cause a large current flow,

overheating, possible burns and even a

breakdown.

6. Do not store the tool and battery cartridge in

locations where the temperature may reach or

exceed 50 ﾟ C (122 ﾟ F).

7. Do not incinerate the battery cartridge even if

it is severely damaged or is completely worn

out. The battery cartridge can explode in a fire.

8. Be careful not to drop or strike battery.

9. Do not use a damaged battery.

SAVE THESE INSTRUCTIONS.

Tips for maintaining maximum battery life

1. Charge the battery cartridge before

completely discharged.

Always stop tool operation and charge the

battery cartridge when you notice less tool

power.

2. Never recharge a fully charged battery

cartridge.

Overcharging shortens the battery service life.

3. Charge the battery cartridge with room

temperature at 10 ﾟ C - 40 ﾟ C (50 ﾟ F - 104 ﾟ F).

Let a hot battery cartridge cool down before

charging it.

4. Charge the battery cartridge once in every six

months if you do not use it for a long period of

time.

5

FUNCTIONAL DESCRIPTION

CAUTION:

• Always be sure that the tool is switched off and the

battery cartridge is removed before adjusting or

checking function on the tool.

Installing or removing battery cartridge

1

2

008797

•

Always switch off the tool before installing or

removing of the battery cartridge.

• To remove the battery cartridge, withdraw it from

the tool while pressing the buttons on both sides of

the cartridge.

• To install the battery cartridge, hold it so that the

battery cartridge front shape fits to that of the

battery installment opening and slip it into place.

Always insert it all the way until it locks in place with

a little click. If not, it may accidentally fall out of the

tool, causing injury to you or someone around you.

• Do not use force when installing the battery

cartridge. If the cartridge does not slide in easily, it

is not being inserted correctly.

Switch action

1

011763

CAUTION:

• Before inserting the battery cartridge into the tool,

always check to see that the switch trigger actuates

properly and returns to the "OFF" position when

released.

To start the tool, simply pull the switch trigger. Tool speed

is increased by increasing pressure on the switch trigger.

Release the switch trigger to stop.

Electric brake

This tool is equipped with an electric brake. If the tool

consistently fails to quickly stop after switch trigger

release, have tool serviced at a Makita service center.

Turning on the front lamp

1

011767

CAUTION:

• Do not look in the light or see the source of light

directly.

Pull the switch trigger to turn on the light. The lamp keeps

on lighting while the switch trigger is being pulled.

NOTE:

• Use a dry cloth to wipe the dirt off the lens of lamp.

Be careful not to scratch the lens of lamp, or it may

lower the illumination.

Reversing switch action

1

011764

This tool has a reversing switch to change the direction of

rotation. Depress the reversing switch lever from the A

side for clockwise rotation or from the B side for

counterclockwise rotation.

When the reversing switch lever is in the neutral position,

the switch trigger cannot be pulled.

CAUTION:

• Always check the direction of rotation before

operation.

• Use the reversing switch only after the tool comes

to a complete stop. Changing the direction of

rotation before the tool stops may damage the tool.

• When not operating the tool, always set the

reversing switch lever to the neutral position.

1. Reversing

switch lever

1. Lamp

1. Switch trigger

1. Button

2. Battery cartridge

6

ASSEMBLY

CAUTION:

• Always be sure that the tool is switched off and the

battery cartridge is removed before carrying out

any work on the tool.

Selecting correct socket

Always use the correct size socket for bolts and nuts. An

incorrect size socket will result in inaccurate and

inconsistent fastening torque and/or damage to the bolt

or nut.

Installing or removing socket

1

2

011765

To install the socket, push it onto the anvil of the tool until

it locks into place.

To remove the socket, simply pull it off.

OPERATION

011766

The proper fastening torque may differ depending upon

the kind or size of the bolt, the material of the workpiece

to be fastened, etc. The relation between fastening

torque and fastening time is shown in the figures.

80

60

40

20

0

1.0 2.0 3.0

Fastening torque

M8(5/16")

M10(3/8")

Fastening time (S)

Proper fastening torque

(29)

(14)

N m

(ft lbs)

(58)

(43)

Standard bolt

M12(1/2")

M10(3/8")

M8(5/16")

011825

0 1.0 2.0 3.0

High tensile bolt

Fastening torque

M6(1/4")

Fastening time (S)

Proper fastening torque

M6

80

60

40

20

M8(5/16")

M10(3/8")

(29)

(14)

N m

(ft lbs)

(58)

(43)

M10

(3/8")

M8

(5/16")

(1/4")

011823

Hold the tool firmly and place the socket over the bolt or

nut. Turn the tool on and fasten for the proper fastening

time.

NOTE:

• When fastening screw M8 (5/16") or smaller,

carefully adjust pressure on the switch trigger so

that the screw is not damaged.

• Hold the tool pointed straight at the bolt or nut

without applying excessive pressure on the tool.

• Excessive fastening torque may damage the

bolt/nut or socket. Before starting your job, always

perform a test operation to determine the proper

fastening time for your bolt or nut. Especially for the

bolt smaller than M8 (5/16"), perform the above test

operation to prevent the trouble on socket or bolt,

etc.

• If the tool is operated continuously until the battery

cartridge has discharged, allow the tool to rest for

more than 15 minutes before proceeding with a

fresh battery.

The fastening torque is affected by a wide variety of

factors including the following. After fastening, always

check the torque with a torque wrench.

1. Socket

2. Anvil

7

1. When the battery cartridge is discharged almost

completely, voltage will drop and the fastening

torque will be reduced.

2. Socket

• Failure to use the correct size socket will cause

a reduction in the fastening torque.

• A worn socket (wear on the hex end or square

end) will cause a reduction in the fastening

torque.

3. Bolt

• Even though the torque coefficient and the

class of bolt are the same, the proper fastening

torque will differ according to the diameter of

bolt.

• Even though the diameters of bolts are the

same, the proper fastening torque will differ

according to the torque coefficient, the class of

bolt and the bolt length.

4. The use of the universal joint or the extension bar

somewhat reduces the fastening force of the

impact wrench. Compensate by fastening for a

longer period of time.

5. The manner of holding the tool or the material of

driving position to be fastened will affect the

torque.

6. Operating the tool at low speed will cause a

reduction in the fastening torque.

Using holster (optional accessory)

CAUTION:

• Do not use for tools such as a drill with a bit

installed on them.

• Turn off a tool and wait until it comes to a complete

stop before placing in the holster.

Be sure to close the holster securely so that it holds

the tool firmly.

008807

Thread a waist belt or similar through holster holder.

008808

Put the tool in the holster and lock it with the holster

button.

MAINTENANCE

CAUTION:

• Always be sure that the tool is switched off and the

battery cartridge is removed before attempting to

perform inspection or maintenance.

• Never use gasoline, benzine, thinner, alcohol or the

like. Discoloration, deformation or cracks may

result.

To maintain product SAFETY and RELIABILITY, repairs,

any other maintenance or adjustment should be

performed by Makita Authorized or Factory Service

Centers, always using Makita replacement parts.

OPTIONAL ACCESSORIES

CAUTION:

• These accessories or attachments are

recommended for use with your Makita tool

specified in this manual. The use of any other

accessories or attachments might present a risk of

injury to persons. Only use accessory or

attachment for its stated purpose.

If you need any assistance for more details regarding

these accessories, ask your local Makita Service Center.

• Plastic carrying case

• Various type of Makita genuine batteries and

chargers

• Holster

NOTE:

• Some items in the list may be included in the tool

package as standard accessories. They may differ

from country to country.

Page is loading ...

Makita LCT309W User guide

Makita LCT309W User guide

in other languages

Related papers

Other documents