Black & Decker DR260C User manual

Catalog Numbers DR260, DR340, DR560

INSTRUCTION MANUAL

3/8 in. (10MM) and

1/2 in. (13MM) DRILLS

Thank you for choosing Black & Decker!

Go to www.BlackandDecker.com/NewOwner

to register your new product.

PLEASE READ BEFORE RETURNING THIS

PRODUCT FOR ANY REASON:

If you have a question or experience a problem with your Black & Decker purchase, go to

HTTP://WWW.BLACKANDDECKER.COM/INSTANTANSWERS

If you canʼt find the answer or do not have access to the internet,

call 1-800-544-6986 from 8 a.m. to 5 p.m. EST Mon. -- Fri. to speak with an agent.

Please have the catalog number available when you call.

for instant answers 24 hours a day.

VEA EL ESPAÑOL EN LA CONTRAPORTADA.

INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA DE GARANTÍA.

ADVERTENCIA: LÉASE ESTE INSTRUCTIVO ANTES DE USAR EL PRODUCTO.

SAVE THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE.

DR260

DR340

DR560

2

General Power Tool Safety Warnings

WARNING! Read all safety warnings and instructions. Failure to follow the warnings

and instructions may result in electric shock, fire and/or serious injury.

Save all warnings and instructions for future reference.

The term “power tool” in the warnings refers to your mains-operated (corded) power tool or

battery-operated (cordless) power tool.

1) Work area safety

a) Keep work area clean and well lit. Cluttered or dark areas invite accidents.

b) Do not operate power tools in explosive atmospheres, such as in the presence

of flammable liquids, gases or dust. Power tools create sparks which may ignite

the dust or fumes.

c) Keep children and bystanders away while operating a power tool. Distractions

can cause you to lose control.

2) Electrical safety

a) Power tool plugs must match the outlet. Never modify the plug in any way. Do

not use any adapter plugs with earthed (grounded) power tools. Unmodified

plugs and matching outlets will reduce risk of electric shock.

b) Avoid body contact with earthed or grounded surfaces such as pipes,

radiators, ranges and refrigerators. There is an increased risk of electric shock if

your body is earthed or grounded.

c) Do not expose power tools to rain or wet conditions. Water entering a power tool

will increase the risk of electric shock.

d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging

the power tool. Keep cord away from heat, oil, sharp edges or moving parts.

Damaged or entangled cords increase the risk of electric shock.

e) When operating a power tool outdoors, use an extension cord suitable for

outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock.

f) If operating a power tool in a damp location is unavoidable, use a ground fault

circuit interrupter (GFCI) protected supply. Use of a GFCI reduces the risk of

electric shock.

3) Personal safety

a) Stay alert, watch what you are doing and use common sense when operating a

power tool. Do not use a power tool while you are tired or under the influence

of drugs, alcohol or medication. A moment of inattention while operating power

tools may result in serious personal injury.

b) Use personal protective equipment. Always wear eye protection. Protective

equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection

used for appropriate conditions will reduce personal injuries.

c) Prevent unintentional starting. Ensure the switch is in the off-position before

connecting to power source and/or battery pack, picking up or carrying the

tool. Carrying power tools with your finger on the switch or energizing power tools

that have the switch on invites accidents.

d) Remove any adjusting key or wrench before turning the power tool on. A

wrench or a key left attached to a rotating part of the power tool may result in

personal injury.

e) Do not overreach. Keep proper footing and balance at all times. This enables

better control of the power tool in unexpected situations.

f) Dress properly. Do not wear loose clothing or jewellery. Keep your hair,

clothing and gloves away from moving parts. Loose clothes, jewellery or long hair

can be caught in moving parts.

g) If devices are provided for the connection of dust extraction and collection

facilities, ensure these are connected and properly used. Use of dust collection

can reduce dust-related hazards.

44))

Power tool use and care

a) Do not force the power tool. Use the correct power tool for your application.

The correct power tool will do the job better and safer at the rate for which it was

designed.

b) Do not use the power tool if the switch does not turn it on and off. Any power

tool that cannot be controlled with the switch is dangerous and must be repaired.

c

) Disconnect the plug from the power source and/or the battery pack from the

power tool before making any adjustments, changing accessories, or storing

power tools. Such preventive safety measures reduce the risk of starting the power

tool accidentally.

d) Store idle power tools out of the reach of children and do not allow persons

unfamiliar with the power tool or these instructions to operate the power tool.

Power tools are dangerous in the hands of untrained users.

e) Maintain power tools. Check for misalignment or binding of moving parts,

breakage of parts and any other condition that may affect the power toolʼs

operation. If damaged, have the power tool repaired before use. Many accidents

are caused by poorly maintained power tools.

f) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp

cutting edges are less likely to bind and are easier to control.

g) Use the power tool, accessories and tool bits etc., in accordance with these

instructions, taking into account the working conditions and the work to be

performed. Use of the power tool for operations different from those intended could

result in a hazardous situation.

5) Service

a) Have your power tool serviced by a qualified repair person using only identical

replacement parts. This will ensure that the safety of the power tool is maintained.

SPECIFIC SAFETY RULES

• Wear ear protectors with impact drills. Exposure to noise can cause hearing loss.

• Use auxiliary handles supplied with the tool. Loss of control can cause personal injury.

• Hold power tools by insulated gripping surfaces when performing an operation

where the cutting tool may contact hidden wiring or its own cord. Contact with a

"live" wire will make exposed metal parts of the tool "live" and shock the operator.

• Use clamps or another practical way to secure and support the work piece to a

stable platform. Holding the work by hand or against your body leaves it unstable and

may lead to loss of control.

• Keep your hair, clothing, and gloves away from air vents. Air vents often cover

moving parts in which these items can be caught.

• Hold tool firmly with two hands (see figure A). Use auxiliary handle if provided. Loss

of control can cause personal injury.

WARNING: Some dust created by power sanding, sawing, grinding, drilling,

and other construction activities contains chemicals known to the State of

California to cause cancer, birth defects or other reproductive harm. Some

examples of these chemicals are:

• lead from lead-based paints,

• crystalline silica from bricks and cement and other masonry products, and

• arsenic and chromium from chemically-treated lumber.

Your risk from these exposures varies, depending on how often you do this type of

work. To reduce your exposure to these chemicals: work in a well ventilated area, and

work with approved safety equipment, such as those dust masks that are specially

designed to filter out microscopic particles.

• Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling,

and other construction activities. Wear protective clothing and wash exposed

areas with soap and water. Allowing dust to get into your mouth, eyes, or lay on the

skin may promote absorption of harmful chemicals.

WARNING: Use of this tool can generate and/or disperse dust, which may

cause serious and permanent respiratory or other injury. Always use NIOSH/OSHA

approved respiratory protection appropriate for the dust exposure. Direct particles

away from face and body.

WARNING: ALWAYS use safety glasses. Everyday eye glasses are NOT safety

glasses. Also use face or dust mask if cutting operation is dusty.

ALWAYS WEAR CERTIFIED SAFETY EQUIPMENT:

• ANSI Z87.1 eye protection (CAN/CSA Z94.3)

• ANSI S12.6 (S3.19) hearing protection

• NIOSH/OSHA/MSHA respiratory protection

WARNING: Always wear proper personal hearing protection that conforms to

ANSI S12.6 (S3.19) during use. Under some conditions and duration of use, noise

from this product may contribute to hearing loss.

3

SAFETY GUIDELINES - DEFINITIONS

It is important for you to read and understand this manual.

The information it contains relates to protecting YOUR SAFETY and PREVENTING

PROBLEMS. The symbols below are used to help you recognize this information.

DANGER: Indicates an imminently hazardous situation which, if not avoided, will

result in death or serious injury.

WARNING: Indicates a potentially hazardous situation which, if not avoided, could

result in death or serious injury.

CAUTION: Indicates a potentially haz ard ous situation which, if not avoided, may

result in minor or mod er ate injury.

CAUTION: Used without the safety alert symbol indicates a potentially hazardous

situation which, if not avoided, may result in property damage.

The label on your tool may include the following symbols.

V ..........................volts A..........................amperes

Hz ........................hertz W ........................watts

min........................minutes ......................alternating

current

......................direct current

n

o ........................no load speed

..........................

Class II Construction

........................earthing terminal

........................safety alert symbol

.../min....................revolutions or bpm.....................beats per minute

reciprocations per minute

Extension Cords

When using an extension cord, be sure to use one heavy enough to carry the current your

product will draw. An undersized cord will cause a drop in line voltage resulting in loss of

power and overheating. The following table shows the correct size to use depending on

cord length and nameplate ampere rating. If in doubt, use the next heavier gauge. The

smaller the gauge number, the heavier the cord.

4

Minimum Gauge for Cord Sets

Volts Total Length of Cord in Feet

120V 0-25 26-50 51-100 101-150

(0-7,6m) (7,6-15,2m) (15,2-30,4m) (30,4-45,7m)

240V 0-50 51-100 101-200 201-300

(0-15,2m) (15,2-30,4m) (30,4-60,9m) (60,9-91,4m)

Ampere Rating

More Not more American Wire Gauge

Than Than

0-6 18 16 16 14

6-10 18 16 14 12

10 - 12 16 16 14 12

12 - 16 14 12 Not Recommended

FUNCTIONAL

DESCRIPTION

1. Variable speed switch

2. Lock-on button

3. Forward/reverse slider

4. Chuck

5. Bit storage

6. Bubble level (DR260, DR340)

7. Chuck key (DR560)

7a. Chuck key holder (DR560)

8. Side handle (DR560)

DR260

DR340

DR560

1

2

3

4

5

8

1

2

3

4

5

1

2

3

4

7a

7

6

5

Safety Warnings and Instructions: Drills

WARNING: Shock hazard. When drilling or driving into walls, floors or wherever

live electrical wires may be encountered, DO NOT TOUCH ANY METAL PARTS OF

THE TOOL! Hold the tool only by the plastic handle(s) / housing to prevent shock.

• Do not lock the tool ON when drilling by hand. Refer to Operating Instructions-Switching

On and Off.

• Hold drill firmly with both hands to control

the twisting action of the drill (figure A). If

your drill is equipped with a side handle,

always use the side handle.

WARNING: Drill may stall (if overloaded or

improperly used) causing a twist. Always

expect the stall. Grip the drill firmly to control

the twisting action and prevent loss of control

which could cause personal injury. If a stall

does occur, release the trigger immediately

and determine the reason for the stall before

re-starting.

• Always unplug the drill when attaching or

removing accessories. When attaching

accessories in the drill chuck, it is important to securely tighten the chuck using all three

holes to prevent slippage. When using a keyless chuck, hand tighten firmly.

Motor

Be sure your power supply agrees with nameplate marking. 120 Volts AC only means

your drill will operate on standard 60 Hz household power. Do not operate AC tools on

DC. A rating of 120 volts AC/DC means that your tool will operate on standard 60 Hz AC or

DC power. This information is printed on the nameplate. Lower voltage will cause loss of

power and can result in over-heating. All Black & Decker tools are factory-tested; if this

tool does not operate, check the power supply.

Assembly

WARNING: To reduce the risk of injury, before assembly,

make sure that the tool is switched off and unplugged.

Attaching the side handle - DR560 (fig. B)

If your drill is equipped with a side handle, it must be

installed properly to control the drill.

• Turn the grip counterclockwise until you can slide the side

handle (8) onto the front of the tool as shown.

• Rotate the side handle into the desired position.

• Tighten the side handle by turning the grip clockwise.

Inserting a drill bit or other accessory (fig. C & D)

WARNING: Do not attempt to tighten drill bits (or any

other accessory) by gripping the front part of the

chuck and turning the tool on. Damage to the chuck

and personal injury may occur when changing

accessories.

WARNING: Always ensure the bit is

secure before starting the tool. A loose bit

may eject from tool causing possible

personal injury.

Keyless two sleeve chuck (DR260) (fig. C)

• Open the chuck (4) by grasping the rear half

(9) with one hand and use your other hand to

rotate the front sleeve (10) counterclockwise

as viewed from the chuck end.

• Insert the accessory shaft into the chuck to

about 3/4in. (19 mm) depth, centered in the jaws.

• Tighten securely by holding the rear half of

the chuck and rotating the front sleeve in the

clockwise direction as viewed from the chuck

end.

B

C

8

10

9

4

6

A

Keyless single sleeve chuck (DR340)

This tool is equipped with a feature that automatically locks the spindle when the tool is

not running. This feature is a normal condition which allows for tightening or loosening of

the chuck with one hand while holding the drill with the other.

• To change accessories, loosen the chuck by rotating the sleeve counterclockwise as

viewed from the chuck end.

• Insert the accessory shaft into the chuck to about 3/4in. (19 mm) depth, centered in the

jaws.

• Tighten securely by rotating the sleeve in the clockwise direction as viewed from the

chuck end.

Chuck and key (DR560) (fig. D)

• Open the chuck (4) by turning the collar

counterclockwise (when viewed from the

chuck end).

• Insert the accessory shaft into the chuck to

about 3/4 in. (19 mm) depth, centered in the

jaws.

• Tighten chuck collar by hand. Place chuck

key (7) into each of the three holes and

securely tighten in a clockwise direction.

NOTE: Tighten chuck with all three holes to

prevent slippage.

Removing and attaching the chuck (fig. E)

Keyless chuck (DR260, DR340)

• Open the chuck (4) as far as possible.

• Remove the chuck retaining screw (11),

located in the chuck, by turning it clockwise

using a screwdriver (lefthand thread).

• Tighten an allen key (12) of 1/4in. (6mm) or

greater size (not supplied) into the chuck and

strike it with a soft hammer (13) in a

clockwise direction as shown.

• Remove the allen key.

• Remove the chuck by turning it

counterclockwise.

• To attach the chuck, screw it onto the spindle

and secure it with the chuck retaining screw.

Keyed chuck (DR560) (fig. F)

• Place chuck key (7) in any one of the three

holes in the chuck (4).

• Using a soft hammer (13), strike the key in a

clockwise direction. This will loosen the

screw (11) inside the chuck.

• Open chuck jaws fully and remove the chuck

retaining screw, located in the chuck, by

turning it clockwise using a screwdriver

(lefthand thread).

• Place key in chuck. Using a soft hammer

(13), strike key sharply in a counterclockwise

direction.

• Remove the chuck by turning it

counterclockwise.

• To attach the chuck, screw it onto the spindle

and secure it with the chuck retaining screw.

D

F

E

4

7

12

13

11

4

7

11

13

7

Operating Instructions

WARNING: To reduce the risk of serious personal injury, read, understand and

follow all safety warnings and instructions prior to using tool.

WARNING: It is important to support the work properly and to hold the drill

firmly to prevent loss of control which could cause personal injury. If you have any

questions on how to properly operate tool, call: 1-800-544-6986.

WARNING: Do not attempt to tighten drill bits (or any other accessory) by

gripping the front part of the chuck and turning the tool on. Damage to the chuck

and personal injury may occur when changing accessories.

WARNING: To reduce the risk of injury, always unplug drill from power supply

before making any adjustments or changing accessories.

WARNING: To reduce the risk of injury, let the tool work at its own pace. Do not

overload.

Selecting the direction of rotation

For drilling and for tightening screws, use forward (clockwise) rotation. For loosening

screws or removing a jammed drill bit, use reverse (counterclockwise) rotation.

WARNING: Never change the direction of rotation while the motor is running.

Models DR260, DR340

• To select forward rotation, push the forward/reverse slider (3) to the right (when viewed

from the chuck end).

• To select reverse rotation, push the forward/reverse slider (3) to the left (when viewed

from the chuck end).

Model DR560

• To select forward rotation, push the forward/reverse slider (3) to the left (when viewed

from the chuck end).

• To select reverse rotation, push the forward/reverse slider (3) to the right (when viewed

from the chuck end).

Switching on and off

• To switch the tool on, press the variable speed switch (1). The tool speed depends on

how far you press the switch.

• For continuous operation, press the lock-on button (2) and release the variable speed

switch. This option is available only at full speed.

• To switch the tool off, release the variable speed switch. To switch the tool off when in

continuous operation, press the variable speed switch once more and release it.

WARNING: The drill should only be locked ON when it is held stationary in a drill

press stand or other means; NOT BY HAND! Never unplug the tool with the locking

feature engaged. To do so will cause the tool to start immediately the next time it is

plugged in.

Built-in level (DR260, DR340)

Your drill is equipped with a bubble level that assists you in

drilling level holes.

• For horizontal drilling, tilt the drill up or down as required so the

bubble floats in the center of the parallel lines drawn on the

glass.

• When the bubble (6) is centered between the lines, as shown in

figure G, the drill is level.

• To assure accuracy, first place a level on your workpiece and

position it so that it is level. Then, when the drill reads level, the

two will be aligned. (Any bubble level can only indicate level

relative to the earth.)

NOTE: The level is filled with mineral oil that may cause minor

skin or eye irritation when contacted. If the level breaks and this

fluid gets on your skin, rinse thoroughly with water. If any liquid

gets in your eyes, rinse thoroughly with water and call a

physician immediately.

G

6

8

Drilling

• Always unplug the drill when attaching or removing accessories. When attaching

accessories in the drill chuck, it is important to securely tighten the chuck using all three

holes to prevent slippage. When using a keyless chuck, hand tighten firmly.

• Use sharp drill bits only.

• Support and secure work properly, as instructed in the safety instructions.

• Use appropriate and required safety equipment, as instructed in the safety instructions.

• Secure and maintain work area, as instructed in the safety instructions.

• Plug in drill. Make sure switch turns drill on and off.

• Run the drill very slowly, using light pressure, until the hole is started enough to keep the

drill bit from slipping out of it.

• Apply pressure in a straight line with the bit. Use enough pressure to keep the bit biting

but not so much as to stall the motor or deflect the bit.

• Hold the drill firmly with both hands to control its twisting action (figure A).

• Use side handle if drill (DR560) is equipped with one.

• DO NOT CLICK THE TRIGGER OF A STALLED DRILL OFF AND ON IN AN ATTEMPT

TO START IT. DAMAGE TO THE DRILL CAN RESULT.

• Minimize stalling on breakthrough by reducing pressure and slowly drilling through the

last part of the hole.

• Keep the motor running while pulling the bit out of a drilled hole. This will help reduce jamming.

Drilling In Wood

Holes in wood can be made with the same twist drill bits used for metal or with spade bits.

These bits should be sharp and should be pulled out frequently when drilling to clear chips

from the flutes.

Drilling In Metal

Use a cutting lubricant when drilling metals. The exceptions are cast iron and brass which

should be drilled dry. The cutting lubricants that work best are sulfurized cutting oil or lard oil.

Troubleshooting

Problem Possible Cause Possible Solution

• Unit will not start. • Cord not plugged in. • Plug tool into a working

outlet.

• Forward/reverse slider not fully • Push slider completely to

depressed in desired direction. the left or right.

• Circuit fuse is blown. • Replace circuit fuse.

(If the product repeatedly

causes the circuit fuse to

blow, discontinue use

immediately and have it

serviced at a Black &

Decker service center or

authorized servicer.)

• Circuit breaker is tripped. • Reset circuit breaker.

(If the product repeatedly

causes the circuit breaker

to trip, discontinue use

immediately and have it

serviced at a Black &

Decker service center or

authorized servicer.)

• Cord or switch is damaged. • Have cord or switch

replaced at Black &

Decker Service Center or

Authorized Servicer.

For assistance with your product, visit our website www.blackanddecker.com for the

location of the service center nearest you or call the BLACK & DECKER help line at

1-800-544-6986.

9

10

MAINTENANCE

Use only mild soap and damp cloth to clean the tool. Never let any liquid get inside the

tool; never immerse any part of the tool into a liquid.

IMPORTANT: To assure product SAFETY and RELIABILITY, repairs, maintenance and

adjustment should be performed by authorized service centers or other qualified service

personnel, always using identical replacement parts.

ACCESSORIES

Recommended accessories for use with your tool are available from your local dealer or

authorized service center. If you need assistance regarding accessories, please call:

1-800-544-6986.

WARNING: The use of any accessory not recommended for use with this tool could

be hazardous.

SERVICE INFORMATION

All Black & Decker Service Centers are staffed with trained personnel to provide

customers with efficient and reliable power tool service. Whether you need technical

advice, repair, or genuine factory replacement parts, contact the Black & Decker location

nearest you. To find your local service location, refer to the yellow page directory under

"Tools—Electric" or call: 1-800-544-6986 or visit www.blackanddecker.com

FULL TWO-YEAR HOME USE WARRANTY

Black & Decker (U.S.) Inc. warrants this product for two years against any defects in

material or workmanship. The defective product will be replaced or repaired at no charge

in either of two ways.

The first, which will result in exchanges only, is to return the product to the retailer from

whom it was purchased (provided that the store is a participating retailer). Returns should

be made within the time period of the retailerʼs policy for exchanges (usually 30 to 90 days

after the sale). Proof of purchase may be required. Please check with the retailer for their

specific return policy regarding returns that are beyond the time set for exchanges.

The second option is to take or send the product (prepaid) to a Black & Decker owned or

authorized Service Center for repair or replacement at our option. Proof of purchase may

be required. Black & Decker owned and authorized Service Centers are listed under

"Tools-Electric" in the yellow pages of the phone directory.

This warranty does not apply to accessories. This warranty gives you specific legal rights

and you may have other rights which vary from state to state or province to province.

Should you have any questions, contact the manager of your nearest Black & Decker

Service Center. This product is not intended for commercial use.

FREE WARNING LABEL REPLACEMENT: If your warning labels become illegible or are

missing, call 1-800-544-6986 for a free replacement.

LATIN AMERICA: This warranty does not apply to products sold in Latin America. For

products sold in Latin America, check country specific warranty information contained in

the packaging, call the local company or see the website for warranty information.

MAXIMUM RECOMMENDED CAPACITIES

Cat. # Type Steel Soft Wood Hard Wood Masonry

DR260 3/8in. Drill 3/8in.(10mm) Twist Bit 1-1/4in.(31.7mm) 1in.(25.4mm) N/A

DR340 3/8in. Drill 3/8in.(10mm) Twist Bit 1-1/4in.(31.7mm) 1in.(25.4mm) N/A

DR560 1/2in. Drill 1/2in.(13mm) Twist Bit 1-1/2in.(38.1mm) 1-1/4in.(31.7mm) N/A

See ‘Tools-

Electric’

– Yellow Pages –

for Service &

Sales

Imported by

Black & Decker (U.S.) Inc.,

701 E. Joppa Rd.

Towson, MD 21286 U.S.A.

Page is loading ...

22

TALADROS Y TALADROS DE PERCUSIÓN DE

10 mm (3/8 pulg.) Y 13 mm ( 1/2 pulg.)

LEA EL MANUAL ANTES DE DEVOLVER

ESTE PRODUCTO POR CUALQUIER MOTIVO:

Si tiene una consulta o algún inconveniente con su producto Black & Decker, visite

HTTP://WWW.BLACKANDDECKER.COM/INSTANTANSWERS

Si no encuentra la respuesta o no tiene acceso a Internet, llame al 1-800-544-6986 de

lunes a viernes de 8 a.m. a 5 p.m. hora del Este para hablar con un agente.

Cuando llame, tenga a mano el número de catálogo.

para obtener respuestas instantáneas las 24 horas del día.

Catálogo N° DR260, DR340, DR560

Gracias por elegir Black & Decker!

Visite www.BlackandDecker.com/NewOwner

para registrar su nuevo producto.

CONSERVE ESTE MANUAL PARA FUTURAS CONSULTAS.

MANUAL DE INSTRUCCIONES

DR260

DR340

DR560

Page is loading ...

Black & Decker DR260C User manual

Black & Decker DR260C User manual

in other languages

Related papers

Other documents