Toto Link G150R Quick Installation Manual

Category
Routers
Type
Quick Installation Manual
Hardware Installation If you access Internet by 3G, please comply with step 1 & 5; if you access internet by ADSL, please comply with step 1 - 4 as below.
1. Please disconnect the power adapter and all cables during
thunderstorm weather;
2. Keep away from heat source and keep well ventilated;
3. Please pay attention to the waterproofing and moisture-proof
when storing, transporting and running.
4. The power supply must reach the rated current and power.
5. Put the router in flat places.
Set Up PC
For Windows 2000 or Windows XP Operating System, please comply with following steps to set up.
Right-click “My Network
Places”, click “Properties”
Right-click “Local Area
Connection”, click “Properties”
Double-click “Internet Protocol
(TCP/IP)”
Choose “Obtain an IP address
automatically” and “Obtain DNS
server address automatically”,
click “OK”; go back to previous
interface and click “OK”
For Windows Vista or Windows 7 Operating System, please comply with following steps to set up.
Click “Start— Control Panel— Network
and Internet— Network Connection”,
right-click “Local Area Connection”,
and choose “Properties”.
Double-click “Internet Protocol
Version 4 (TCP/IPv4)”
Choose “Obtain an IP address automatically”
and “Obtain DNS server address automatically”,
click “OK”; go back to previous interface and
click “OK”
Quick Installation Guide
3G Wireless N Router
NOTE:
Set Up Router
Please set up the router following below steps.
Run the Web browser.
Input the User Name and Password, then click Login button
(The default Username and Password is admin).
Then you wil see the Easy Setup interface.
(5.2) Input the User NamePasswordAPN and Dial Number the ISP
provides.
When your 3G router connected 3G network successfully, the connect status
will display “Connected”.
Wireless Network Connection
Right-click “My Network
Places”, click “Properties”
Right-click “Wireless Network
Connection”, and click “View
Available Wireless Networks”
Confirm the wireless network SSID name,
choose one that you would like to connect,
then click “Connect”
Input the encrytion key and click “Connect”
Have connected wireless network, you can access
Internet through wireless mode.
For more information, please go to www.totolink.net
Type http://192.168.1.1 in the web browser, then press Enter.
Choose the WAN Access Type, the default is USB3G/Dual Wan
Access USB3G.
You can change wireless state, wireless SSID and encryption conveniently
as well.
After you have finished your settings, please click Apply to save them.
Here we take the encryption of WPA-Mixed for example to setup the router.
(1) Choose Authentication Mode
(2) Choose WPA Cipher Suit
(3) Choose WPA2 Cipher Suite
(4) Choose Pre-Shared Key Format
(5) Input the Pre-Shared Key
7
Information in this document is subject to change without prior notice.
FAQ
Forget the password?
5
How to reset the router to default settings?
1. Please make sure your router’s power is on regularly, then press the
RST-WPS button for about 10s.
2. Loosen the button until your router’s LED lights all flashing, then you
have reset your router to default settings.
Please reset your router to default settings firstly, and set a new password.
The default Username and Password is admin.
The default IP is 192.168.1.1.
(5.1) If you want to use 3G internet, plug in your 3G USB modem into the
3G router’s USB port.Then choose WAN Access Type USB3G/Dual Wan
Access USB3G
Also, you can choose other WAN Access Type according to your actual situation.
LED Indicators
CPU
WIFI
1/2/3/4LAN
WAN
3G
Light on when router is power on.POWER
Light is on when systems is working.
The indicator light is on when Wi-Fi is enabled.
Light on when WAN port connected successfully.
Light blinking while transmitting or receiving data.
The indicator light is on when 3G USB modem is identified.
Light on when the LAN port successful connected.
Light blinking while transmitting or receiving data.
Ports Description
ON/OFF
1/2/3/4LAN
Reset/WPS
USB
WAN
Used for connecting the power adapter.
DC IN
Used for power on or off the router.
Used for connecting the router to local PC.
Used for connecting the router to the Internet.
Used for inserting 3G USB modem.
Reset: Press the button for more than 5 seconds, the
router will restore factory settings.
WPS: Press the button less than 5 seconds, enable the
router WPS function.
RST WPS
Suitable for: G150R,G300R
3
Router
3G/4G
Network
5
Static IP If your ISP has provided the fixed IP that allows you to access Internet,
please choose this option.
DHCP Client Dynamic Host Configuration Protocol (DHCP) is a local area network
protocol. If you choose this mode, you will get a dynamic IP address from
your ISP automatically.
PPPoE/Dual
Wan Access
PPPoE
Point-to-Point Protocol over Ethernet (PPPoE) is a virtual private and
secure connection between two systems that enables encapsulated data
transport. Select PPPoE option if ISP provides a PPPoE connection.
PPTP/Dual
Wan Access
PPTP
PPTP means Point to Point Tunneling Protocol is a VPN connection that
only applies in Europe. If you choose one of them, please type in all the
information that your ISP provided for this protocol.
L2TP/ Dual
Wan Access
L2TP
L2TP means Layer 2 Tunneling Protocol is a VPN connection that only
applies in Europe, Middle East and Africa (MEA) regions. If you choose
one of them, please type in all the information that your ISP provided for
this protocol.
USB3G/Dual
Wan Access
USB3G
It supports users connect to Internet by 3G. If you want to use this method,
you should plug in a 3G network card in the router’s USB port first.
V.14.08
  • Page 1 1

Toto Link G150R Quick Installation Manual

Category
Routers
Type
Quick Installation Manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI