User’s guide OPUS profiBINDER&CLOSER
Health & safety precautious
• Before operating the equipment, please read the user guide carefully and follow the instructions.
• profiBINDER&CLOSER is designed to bind documents only. Do not use the machine to punch hard materials
such as metal → it may result in damaging of the machine.
• The device must be placed on a sturdy and level surface.
• The equipment should be protected against dust and moisture. Do not allow any liquid to get inside the unit
• The equipment should be kept out of reach and away from children and animals.
• Pay special attention while stretching the plastic comb open.
• Pay special attention while clamping the wire comb. Do not reach or put fingers into the pressing slot → danger of
injury!
Recommendations
• Use only recommended supplies and accessories
• The equipment is designed to bind documents with plastic and wire combs only
• Unpack and install all the elements of the device ready to operate
• The device must be placed on a sturdy and level surface
• Before binding important documents, test the settings of the equipment on a sheets of paper
NOTE!
Not complying with the above recommendations can result in, the guarantee/warranty
being made VOID.
Construction of the equipment:
1 – Comb binding mechanism
2 – Removable baffle
3 – Wire binding slot
4 – Book support
User’s guide OPUS profiBINDER&CLOSER
5 – Wire binding handle
6 – Wire binding keys
7 - Comb binding handle
8 – Wire hooks
Application
The machine is designed for binding punched paper and plastic or paper covers with plastic ( φ6 mm up to φ50mm )
or wire (3/16" - 1" ) combs
Operation
Binding with plastic comb:
• Install metal paper support on the front of machine.
• Choose correct comb size using chart below showing comb and sheets. SEE construction diagram
Max punching
capacity 10 25 45 65 105 125 145 165
Comb size 4,5 6 8 10 12 14 16 18
Max punching
capacity 180 210 240 270 300 350 440 510
Comb size 20 22 25 28 32 38 45 51
• Put the plastic comb on to the comb expander mechanism on the top machine with the comb opening upwards
• Push the handle (7) backwards gently to open the comb
• Fit the punched holes of the documents on to the opened comb, front cover upwards
•
Pull the handle forward slowly to close the plastic comb
•
Remove bound and ready documents from the comb plate
Binding with wire comb:
• Install plastic book support (4) at the back of machine.
• Choose correct comb size using chart below showing comb and sheets. SEE construction diagram
Comb size 4,8 6,4 8 9,5 11 12,7
Max punching capacity 20 35 50 65 80 90
Comb size 14,3 16 19 22 58
Max punching capacity 120 150 170 200 230
• Hang up the wire on hooks.
• Insert sheets of paper into the open comb. Put the wire comb with the documents into the wire
binding slot.
- Machine is equipped with the magnet which attracts the wire comb into the pressing slot.
• Push down the appropriate binding key (6). Upper line keys arte for 2:1 wire and lower line for 3:1 wire
• Press the pressing handle (5) down in order to clamp the wire comb precisely. Release the handle
• Take the documents out of the pressing slot – the documents are ready!
Note!
When the wire comb is not closed enough you must take the book support (4) off and on front part of machine add
special binding plates (3 pics of 1 mm or 3 pics of 0,5mm). Rugged side of each plate must be directed inside the
machine. Next fix the plastic book support and close wire comb once again.
User’s guide OPUS profiBINDER&CLOSER
Maxiumum length of bound document is 340mm. For longer documents take off removable baffles (2).
Technical data:
Machine binds:
Plastic combs: range from φ6 mm to φ50mm
Wire combs: range 3/16" - 1"
Format: A4
Net weight: 9,5 kg
Gross weight: 11 kg
Dimensions (LxWxH): 490x345x325mm
09.04.2013
dystributor: OPUS Sp. z o.o. ● ul. Toruńska 8 ● 44 – 122 Gliwice ● www.opus.pl
/
