L.A. Steelcraft LA-SW-581-638M Installation guide

Brand: L.A. Steelcraft

Model: LA-SW-581-638M

Type: Installation guide

L.A. Steelcraft LA-SW-581-638M is an 8' Modern Bipod Swing designed for outdoor use in playgrounds. It is made of durable materials and has been designed to reduce injuries. The swing is easy to install and can be used by children of all ages. The swing is also adjustable, so it can be used by children of different heights.

581-638M 8’MODERN BIPOD SWING

Installation Guide

INSTALLATION INSTRUCTIONS

581-638M

8’ MODERN BIPOD SWING

Please read the entire manual before beginning installation.

1 CTN 4 WF 11 PIPE 16 TOTAL PCS 340# WEIGHT CLASS 70

581-638M 8’MODERN BIPOD SWING

Installation Guide

TAB SECTION INDEX

1. 3D AND 2D DRAWINGS

2. INSTALLATION GUIDE

3. INSTALLATION STEPS

4. COMPONENT INSTALLATION

5. APPENDIX

6. ORIGINAL COMPONENT MAINTENANCE FORMS

7. COMPLETED COMPONENT MAINTENANCE FORMS

581-638M 8’MODERN BIPOD SWING

Installation Guide

Table of Contents

3D DRAWING ..........................................................................................

TOP DOWN VIEW ...................................................................................

FOOTING VIEW .......................................................................................

Important ............................................................................................... 6

When your receive your playground ................................................. 6

Before you begin ........................................................................................ 6

Safety Surfacing ................................................................................... 8

Tools and Materials ............................................................................ 9

BEFORE BEGINNING ........................................................................ 10

SITE REQUIREMENTS ............................................................................ 10

MAINTENANCE: ....................................................................................... 10

PLAY AREA: ............................................................................................... 10

Installation Punch List ........................................................................

Footing Layout Example............................................................................

Step 1: Layout........................................................................................... 11

Step 2: Holes ............................................................................................. 11

Step 3: Deck, Post & Component Installation ............................... 12

Step 4: Concrete ...................................................................................... 12

Step 5: Last Step ...................................................................................... 12

Four Hole Bracket & Panel Bracket Installation ..............................

Other Installation Tips ......................................................................... 13

SUPERVISION GUIDE ....................................................................... 14

HARDWARE DRAWINGS

COMPONENT INSTALLATION INSTRUCTION SETS

APPENDIX

FINAL INSTALLATION STEPS

MAINTENANCE AND INSPECTION

581-638M 8’MODERN BIPOD SWING

Installation Guide

581-638M 8’MODERN BIPOD SWING

Installation Guide

581-638M 8’MODERN BIPOD SWING

Installation Guide

Important

Please read completely before beginning installation.

This equipment has been designed for safety as well as challenge and fun. This

equipment has been designed to reduce injuries and therefore must be installed

“Step by Step” per our Instructions.

The U.S. Consumer Product Safety Commission (CPSC) published a report

stating 79% of all playground injuries treated in U.S. Emergency Rooms was the

result of a fall. It is critical that you refer to the Protective Surfacing section of

these instructions, located on the next page prior to installing your playground.

As the owner you are responsible for the safe installation of not only the play

equipment, but also the safety of the site.

When your receive your playground

Identify all parts by comparing them to the part list and component

instruction pages.

Always compare the number of pallets, cartons or other items the BOL

has listed with the number actually received. Note the any discrepancies

on the BOL.

Also note any obvious damage to the packing materials, pallets or

components on the BOL.

Equipment should be inventoried and installed within a few days of

receipt. The packing materials are meant to protect the equipment

during shipping and not for storage. Heat, weather and sunlight can

damage the packing materials, which can impact the components. If

storage is required you must store the equipment in a controlled

environment away from heat, moisture and sunlight. SportsPlay

recommends carefully unpacking the unit and taking an inventory before

storing the equipment. Care should be taken with all powder coated and

thermoplastic-coated parts to prevent damage to the coating.

Before you begin

Review your playground footing and top view drawings to ensure your site is

large enough. These guidelines are available from the CPSC (contact

information for the CPSC is located on the next page).

Read through the entire instruction booklet before beginning the actual

installation.

Before you begin preparing the site or digging any holes you must first

contact you local utility companies so they can visit the site and mark all

of the buried utilities. In the U.S. you may call 811 and your call will be

routed to your local utility center.

This equipment was designed to install on a clear and level site. There

should be no more than 3” of grade variations in a 10’ span.

Footing layout is the first critical step once the installation begins. Mark

all holes using the footing diagram. Prior to digging holes compare the

measurements from the footing diagram to the actual site markings to

ensure accuracy. Then check it again! (Footing info is located on pg 16

in this guide)

Our posts are manufactured to accommodate 12” of protective surfacing.

Evaluate the site for drainage. To ensure good drainage around the

equipment consult a local professional.

Do not leave the jobsite un-attended during installation unless all access

points to the play area are secure, all bolts and fasteners are tight and all

ground holes are covered.

581-638M 8’MODERN BIPOD SWING

Installation Guide

SportsPlay Equipment inc. has provided two warning labels that state:

“WARNING – Installation over a hard surface such as concrete, asphalt

or packed earth may result in serious injury or death from falls.” These

labels must be installed on vertical posts as per ASTM F1487.

Instructions for the placement of these labels are included in the

appendix of this booklet.

SportsPlay will provide manufacturer identification labels that must be

installed on the structure during installation per ASTM F1487.

Installation instructions for these labels are included in the appendix of

this instruction manual.

Labels must be replaced when they are no longer legible. Contact your

distributor for replacement labels.

581-638M 8’MODERN BIPOD SWING

Installation Guide

Safety Surfacing

WARNING! – INSTALLATION OVER A HARD SURFACE SUCH AS

CONCRETE, ASPHALT OR PACKED EARTH MAY RESULT IN

SERIOUS INJURY OR DEATH FROM A FALL

Because accidental falls are likely to occur around play equipment, SportsPlay

Equipment Inc. recommends that a resilient safety surfacing that will meet

standard ASTM F1292 be placed under and around the structure and extend

throughout the entire use zone.

SportsPlay Equipment Inc. does not manufacture safety surfacing. All

manufacturers of safety surfacing require different depths of surfacing for fall

heights. Consult your surfacing supplier about the required safety surfacing

depth for your play equipment.

SportsPlay Equipment Inc. manufactures all playgrounds to accommodate

12” of safety surfacing. If you intend to adjust the height of the surfacing

you will need to adjust the depth of the footing to accommodate the

surfacing height.

Refer to the CPSC Handbook for Public Playground Safety for the recommended

type and depth of the protective surfacing as well as all other playground safety

concerns.

For a copy of the most current issue of the CPSC Handbook for Public

Playground Safety, write to:

U.S. Consumer Product Safety Commission

Office of Information and Public Affairs

Washington DC, 20207

USA

Call - 1-800-638-2772 (US and Canada only)

Call - 301-504-0990

Direct Link - http://www.cpsc.gov

For a copy of either the standard for surfacing (ASTM F1292) or for play

equipment (ASTM 1487) write to:

American Society for Testing and Materials

100 Bar harbor drive

West Conshohocken PA, 19428-2959

USA

Call – 618-832-9585

Web Site – www.astm.org

You must consider the type of safety surfacing you will use before beginning

the installation process. There are two general types, organic/loose fill or

synthetic unitary (pour in place). You must know which type of surfacing

you are going to use prior to installing the playground. This unit was

designed for 12” of loose fill surfacing so if the customer wants to use a

synthetic unitary product that has a much smaller height than 12” you must

dig the footing holes deeper to allow for the difference.

If loose fill surface material is to be used (example: wood mulch) you will

need to consider containment borders. There are many products to choose

from including hard plastic and natural products such as wood (Creosoted

railroad ties are NOT recommended for use as borders in a play area). Loose

fill materials are easily displaced so use of some type of containment border

is necessary to keep the surfacing material inside the intended area. Some

customers also prefer to have a weed mat installed to prevent weed growth.

Choose a mat that will prevent growth but will also allow for drainage.

581-638M 8’MODERN BIPOD SWING

Installation Guide

Tools and Materials

List is for tools and materials needed that are not included with the

playground

Follow manufacturer’s guidelines for proper use of tools and materials.

The best method (also the easiest) to dig the postholes is using a

tractor with a 12” auger attachment.

Shovels (long handled spades)

Post hole digger

Wheelbarrow

Large construction bar (5’)

Claw hammer

Large dead-blow rubber hammer

Small sledgehammer to use in blocking the posts

Strong and sturdy step ladders

Extension cords & power supply

Levels – Magnetic torpedo and 4’ long levels

Scrap lumber to use for shims in post holes to keep posts level

Blocking materials for the post holes (bricks, concrete blocks, etc.)

Files and sand paper

Safety surfacing

Spray paint to mark holes

String line

Cement (2,500 psi minimum)

Straight line or transit level (and tripod) for ensuring hole depths are

at the same level

581-638M 8’MODERN BIPOD SWING

Installation Guide

BEFORE STARTING INSTALLATION OF YOUR PLAYGROUND,

PLEASE READ INSTRUCTIONS THOROUGHLY.

BEFORE BEGINNING

SITE REQUIREMENTS

The Playground system is designed to suit a level site. Should there be any falls

or slopes on the site; care should be taken to accommodate the entry and exit points

and to maintain the correct height. There should not be more than 3” of drop in grade

per every 10’.

The site must be inspected for natural obstacles such as roots or rocks that may

be a trip hazard, poor drainage and sharp objects such as glass.

Every state has different rules and regulations governing digging, some are

stricter than others. In addition, 62 separate One Call Centers serve different

areas of the country; now 811 will connect you directly to your local One Call

Center. Prior to digging, be sure to call 811 or the local One Call Center to

prevent accidentally disrupting local utility service.

MAINTENANCE:

As an owner, it is most important that you are aware of your responsibility to

insure safe use of your new equipment. It is necessary to install equipment

according to the installation instructions provided and inspect the equipment at

regular intervals. During inspection, if any part is found damaged or excessively worn,

equipment should be closed immediately. A maintenance section is included in the

appendix of this instruction booklet.

If a part is missing or damaged the playground must be put out of service while

the part is replaced. Lack of maintenance will result in premature wear, reduced

life expectancy, and possible failure that may result in injury.

All SportsPlay Equipment play events have been engineered to meet all

applicable safety guidelines, but if installed improperly, these problems may

occur:

Entrapment gaps (between 3 1/2” and 9”)

String Entanglements

Protrusions

Make sure that any bolt end that protrudes more than 2 threads past the face of the

nut is trimmed and de-burred smoothly. Always double-check your work.

Installation must adhere to the manufacturer’s assembly manual and all other applicable

safety guidelines.

PLAY AREA:

The area immediately above and around the play structure must be free of any

obstructions such as:

Trees

Other Play Equipment

Buildings

Overhead Power lines

Make sure the play area has all the required safety surfacing and the

minimum fall zones as required by the safety guidelines. These guidelines can

be found at www.cpsc.gov.

CHILDREN MUST BE SUPERVISED AT ALL TIMES. No playground is

safe without adult supervision!

There may be situations that require you to modify the layout or use your own

judgment. If you have any questions contact you distributor.

Reading this entire manual before beginning the installation will help you to

ensure your equipment is installed and maintained correctly.

581-638M 8’MODERN BIPOD SWING

Installation Guide

Step 1: Layout

1. Lay structure in the desired location using the top view layout drawing.

Measure from each post to ensure there is adequate space for any

component and the components fall zone. This drawing is a standard

drawing and does not represent the actual playground you are installing.

2. Most installers like to orientate the playground so that the entry point of

the playground is facing either the sidewalk or the direction from which

the children are entering the play area.

Step 2: Holes

1. If the site grade is not level you have to adjust the footing depth to

maintain a level footing. Check with building codes to ensure you meet

required hole depth and width. If a deeper footing is required you must

add blocking materials to the hole to keep the post depth in accordance

with the footing side view drawing on the next page.

2. Once the structure is in the desired location within the play area, mark

the locations of the post by inserting a stake into the center of each post

location (see drawing below for an example). If using spray paint to

mark location please be careful not to spray the post.

3. Match the post location marks with the footing layout in the front of this

booklet. Dig your holes using the main post footing drawing below. If

your surface grade is not level you should start with the lowest point and

use that hole depth to level all other holes too. The footing drawing

below indicates a depth of 22” plus the thickness of a brick (or the

thickness of whatever blocking material you will use instead of a brick).

This depth is for 12” of surfacing only. If you are using something other

than 12” of surfacing, such as 3” of rubber your hole depth would have

to be 31” plus the thickness of a brick to allow for less surfacing

material.

4. It is recommended that you use a transit to level the remaining post

holes to the first hole in order to ensure that the posts are level.

FOOTING SIDE VIEW

581-638M 8’MODERN BIPOD SWING

Installation Guide

Step 3: Post & Component Installation

1. We recommend installing the posts once the post are square and level

you may add the concrete (concrete with a minimum of 2,500 psi should

be used). Mix concrete per manufacturers instructions and let it cure for

at least 24 hours before continuing.

2. NEVER LEAVE THE INSTALLATION SITE UNATTENDED

WITHOUT ROPING OFF THE AREA AND EQUIPMENT,

INSTALLING ALL HARDWARE, SECURING TOOLS AND

EQUIPMENT, AND COVERING OPEN HOLES WITH A RIGID

MATERIAL (PLYWOOD). CHILDREN WILL TRY TO USE

THE EQUIPMENT EVEN THOUGH ITS NOT FULLY

ASSEMBLED. YOU MUST TAKE ACTION TO PREVENT

INJURY AND DAMAGE.

Step 4: Concrete

1. Verify all swing posts and fittings are tight, level and square. Once the

unit is verified to be level and square you may start installing concrete.

You must use concrete with a minimum of 2,500 psi.

2. Always pre mix the concrete to the manufactures directions before

pouring it into the hole. Never put dry concrete in the hole. Typically

each main posthole requires two 80-pound bags of concrete.

3. Allow concrete to set in accordance with manufacturers directions. Fill

holes too about 2” below the surface with concrete. Once the hole has

been filled with concrete, slope the top of the concrete down and away

from the post to keep water from seeping between the post and the

concrete.

4. Secure playground area to prevent access while the concrete is setting

for a minimum of 48 hours.

5. SportsPlay recommends having a CPSI (certified playground safety

inspector) present during installation. If that’s not possible you should

have the completed playground (after surfacing is in place) inspected by

a CPSI.

Step 5: Last Step

1. After concrete has completely set, backfill all holes with dirt.

2. Install surfacing.

581-638M 8’MODERN BIPOD SWING

Installation Guide

Other Installation Tips

If you are mocking up components with the intention of removing

the hardware at some point, you may want to apply lubricating oil to

the hardware. Stainless steel hardware has a tendency to seize so if you

are planning on removing the hardware you may want to apply lubricant

to prevent this.

Unless specified in the specific component instruction step, do not

tighten the hardware completely until the entire unit is assembled.

581-638M 8’MODERN BIPOD SWING

Installation Guide

SUPERVISION GUIDE

Although the equipment is designed, installed and maintained in accordance with

all safety guidelines adult supervision is required.

Not all equipment is appropriate for all ages. Direct children to age appropriate

equipment.

Younger children will require more supervision than older children.

While eliminating accidents is not likely, following these guidelines will help

minimize accidents.

Basic playground safety for supervisors:

 Make sure all safety surfacing is in place and at the correct height.

Inspect area for hard or sharp objects and remove them.

 No dangerous horseplay in the play area. (Jumping from dangerous

heights, displacing of surfacing, etc…)

 Inspecting for missing or broken equipment. (Do not allow children to

play on broken equipment or equipment with missing components).

 Make sure there are no unsafe modifications (especially ropes tied to

equipment). Remove all unsafe modifications and close the equipment

for play until they are removed.

 Keep children in the designated play area.

 Do not let children play on wet equipment.

 Prevent overcrowding on play equipment.

 Loose clothing, hoods, strings or jewelry shall be tight or not worn

while playing to prevent strangulation.

 Ensure the temperature of the equipment is not hazardous. Direct

sunlight exposure can increase the temperature of the equipment high

enough to cause injury.

 Inspect the playground every day using the General Inspection Checklist

located in the appendix of this manual

The easiest method for performing the daily inspection with the

checklist is to laminate the checklist and use a dry erase marker to mark

the items off before opening the play area

581-638M 8’MODERN BIPOD SWING

Installation Guide

½ X ½ SET

SCREW

5/16 X 1 BUTTON

HEAD NUT

5/16 X 2 ½ BUTTON

HEAD BOLT

5/16 LOCK

WASHER

3/16 ALLEN WRENCH (YELLOW BAG)

¼ ALLEN WRENCH (BLUE BAG)

5/16 ALLEN WRENCH (RED BAG)

581-638M 8’MODERN BIPOD SWING

Installation Guide

COMPONENT INSTALLATION INSTRUCTIONS

March 2, 2016

581-638M 8’ MODERN BIPOD SWING

INSTALLATION INSTRUCTION

INSTALLATION DETAILS

 Recommended crew (Adult): 2

 Installation time: 4 hr

 User age: 5-12

 Use zone: 32’ x 49’

 Weight: 480 lbs

SURFACING: Use of safety surfacing in compliance with

ASTM specification F1292 is required.

MAINTENANCE:

 As the owner of the playground you are responsible for

maintenance of the equipment and play area. A

maintenance schedule must be developed and the

equipment inspected frequently. A maintenance section

that includes component specific maintenance

requirements is included at the end of this manual.

 Be sure to inspect surfacing for foreign objects that could

cause injury and that sufficient surfacing are in place in

accordance with ASTM and CPSC standards.

March 2, 2016

581-638M 8’ MODERN BIPOD SWING

INSTALLATION INSTRUCTION

PARTS LIST

PART #

DESCRIPTION

QTY

583-522

Swing End

583-523

Center Fitting

343-210A

2 3/8” x 11’ Pipe

196-802

½” x ½” Socket Set Screw

116-545

5/16” x 2 ½” Button Head Bolt

216-512

5/16” x 1” Button Head Nut

326-501

5/16” Lock Washer

416-350

3/16” Socket Key

416-400

¼” Socket Key

416-500BPK

5/16” Socket Key

805-532

Warning Label

805-534

SportsPlay Label

516-400

Locktite

NOTE: Keep a copy of these instructions on file to assist you

with maintenance and replacement parts.

March 2, 2016

581-638M 8’ MODERN BIPOD SWING

INSTALLATION INSTRUCTION

FOOTING INFORMATION

 Total footing depth is 24” less the height of the surfacing

plus the height of the blocking material. If you are using

12” of surfacing the footing hole would need to be 12” plus

the height of the blocking material (refer to both the side

and front cutaway views to the right).

 If the Play structure is installed on an unlevel grade you

must adjust the footing depth to accommodate the grade.

For instance, if the grade for this component is 1” higher

than the surface grade of the main playground post you

must dig your footing hole 1” deeper.

 You must place the bottom of the support post or slide leg

on a suitable flat blocking material to prevent it from

sinking further into the soil. We recommend you use a

brick, block of wood or several inches of gravel. The

footing depth does not include this blocking material since

materials used often vary.

 It is the owner/installers responsibility to check local

building codes and to comply with those codes. All footing

depths listed here are recommendations and local soil types

and frost lines may require a deeper and/or wider footing

depth. If that’s the case you must add more blocking

material to accommodate the deeper footing, as the post

length will still only be installed at the depth listed in this

instruction manual.

 Assemble the entire unit before adding the concrete unless

instructed to do so in the individual component instruction

sections.

March 2, 2016

581-638M 8’ MODERN BIPOD SWING

INSTALLATION INSTRUCTION

ELEVATION AND

FOOTING LAYOUT VIEW

Page is loading ...

L.A. Steelcraft LA-SW-581-638M Installation guide

L.A. Steelcraft LA-SW-581-638M Installation guide

L.A. Steelcraft LA-SW-581-638M Installation guide

Related papers

Other documents