LED LIGHT WITH SENSOR
INSTRUCTION MANUAL
UC-5MSL
SUPPORT: [email protected]
DISTRIBUTOR: Ayonz Pty Ltd
To use as a sensor light:
1. Set the On/O/Auto Switch to the
Auto position.
2. Twist the Sensor Part of the Light Tube
(fig. 3) to adjust the Sensor Activation Zone
to face the direction of possible movement.
3. Twist the Light Tube on the Magnetic Mount
(fig. 4) to adjust the Illumination Zone.
4. When set to the Auto position, the light turns
on automatically when it detects motion as
well as insufficient light in the area.
5. For continuous illumination, set the On/O/
Auto Switch to the On position. It will remain
on continuously until turned o manually, or
the battery runs out.
6. To turn o the light completely, set the
On/O/Auto Switch to the O position (fig. 5).
To use as a light wand:
1. Detach the Light Tube from the Magnetic Mount.
2. Set the On/O/Auto Switch to the On position.
Operation Instructions
Fig. 3
Fig. 4
Fig. 5
Cleaning and Maintenance
Caution:
• Switch o the light before doing any cleaning.
• Do not clean with water or allow water to enter inside.
Wipe with a soft dry lint-free cloth as necessary.
Troubleshooting
The light does not turn on.
• In Auto position, the light turns on only if it detects motion when the ambient light
in the area is low.
• Check if the batteries have run out.
• Check if the On/O/Auto Switch is set to the O position.
• Check if the sensors have dust/dirt on them. This could aect the operation.
• Check if there is any visible damage to the light tube.
Important: In Auto position, the light turns on
only if it detects motion when the ambient light
in the area is low.
Product Overview
Important Safety Instructions
1. Read all instructions carefully before use.
2. Keep these instructions for future use.
3. This light is for indoor, domestic use only. It is not designed for commercial,
industrial or trade use.
4. No user-serviceable parts inside. Do not dismantle, or attempt to repair this
unit yourself.
5. The light source of this luminaire is not replaceable; when the light source reaches
its end of life the whole luminaire shall be replaced.
6. Do not look directly into the LED light source.
7. Do not install in locations where the light fitting can easily be accessed by children
or the infirm.
8. Use the provided double-sided tape or screws for installation.
9. This product is not a toy! Children should be supervised to ensure that they do not
play with the appliance.
10. Do not spray water on this product, or immerse in water or other liquids.
Ensure that water does not enter the unit during cleaning.
11. Do not use near heat sources or flammable materials.
Do not mount above stovetops or other surfaces that are exposed to heat.
12. Do not operate with wet hands.
13. Do not cover the light.
14. Danger of explosion! The batteries must not be disassembled, thrown into fire,
or short circuited. Replace only with the same battery or equivalent type. Do not
mix used and new batteries or batteries of dierent types or brands.
15. Remove exhausted batteries from the appliance and dispose of safely.
1. Twilight Sensor
2. Motion Sensor
3. Light Tube
4. Battery Compartment
5. Magnetic Mount
6. On/O/Auto Switch
Not shown:
3 x ‘AA’ Batteries
4 x Screws
2 x Wall Plugs
1 x Double-sided Tape
1 x Instruction Manual (this document)
1 x Warranty Card
1
2
4
5
6
3
Before First Use
This cabinet light requires 3 x ‘AA’ batteries (included).
Open the battery compartment; insert 3 x ‘AA’ batteries, ensuring correct polarity and
then close the battery compartment.
Installation
These cabinet lights are suitable for indoor wall or under-cabinet lighting. Use the
provided Double-sided Tape or Screws to attach the Magnetic Mount on a suitable
surface. The light clicks on to the mount magnetically.
Option 1: Using Double-sided Tape (fig. 1):
Note:
• For secure adhesion, make sure the chosen location is clean, dry and grease-free.
• The Double-Sided tape is very sticky and hard to remove, so choose the location
carefully before sticking.
1. Remove the protective plastic on
one side of the Double-sided Tape,
and attach it to the back of the
Magnetic Mount.
2. Now remove the protective film from
the other side of the Double-sided
Tape, and attach the Magnetic Mount
to the desired location.
Option 2: Using Wall Screws (fig. 2):
1. Detach the Magnetic Mount from the
Light Tube.
2. Hold the Magnetic Mount against
a suitable wall or cabinet surface.
Mark positions and use 2 of the
provided Screws to attach the
Magnetic Mount to the surface.
Notes:
• Use Wall Plugs if necessary for your mounting surface.
• Choose from the long or short screws depending on your wall type.
Fig. 1
(a) (b)
Fig. 2
(a) (b)
Technical Specifications
LEDs: 5 x SMD LEDs (not replaceable)
Battery: 3 x 1.5V - ‘AA’ batteries
Lumen output: 44 lumens
Sensor range: Up to 4m
Sensor angle: 100 degrees
Colour temperature: 6400K
Dimensions: 25 x 2.5 x 3 cm
-
1
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Other documents
-
smpl 731069 Motion Alert Kit User guide
-
AEI Security & Communications 3400 Installation & Operation Manual
-
HobbyZone HBZ32000LE Owner's manual
-
Yamaha DVXS60 User manual
-
Cascadia X0030 Installation guide
-
Kodak PIXPRO ORBIT360 4K User manual
-
Meade Advanced Coma-Free f/8 LX600 with StarLock Owner's manual
-
-
RAB Lighting IVGT5-50L750WU/LCE2 Operating instructions
-
RED SHIELD WS100G2 User manual
