TireMinder Solar Powered Trailer TPMS Additional Instructions
Replace a Transmitter (Learn Mode)
To replace a transmitter on the TireMinder Solar
Powered Trailer TPMS, please use the following
instructions:
1. Remove the original transmitter you wish to
replace from the valve stem.
2. Make sure you are in Monitoring Mode.
Monitoring Mode is the mode where you can
switch between °F and °C by pressing and
releasing the left button.
3. Press and hold the left and right buttons on the
top of the 5 seconds, release once you hear a
beep.
4. After the beep you will be in Learn Mode and
see the top left tire blinking.
5. Select the tire position you would like to replace
by pressing and releasing the left or right
buttons to move to different tire positions.
6. Once at the desired tire position, press and hold
the center button until you hear a beep and see
“---“.
7. Screw the transmitter onto the corresponding
tire position. Within 12 seconds, you should
hear a beep and see the new tire pressure.
8. If you wish to replace additional tire positions,
repeat steps 5 to 7 until you have replaced the
desired tire positions.
9. You will now need to return to Monitoring Mode.
Press and hold the left and right buttons for 5
seconds, release once you hear a beep.
10. You should now be back in Monitoring Mode.
Confirm this by toggling the temperature using
the left button.
Adjust Baseline Pressures (Baseline Pressure Setting
Mode)
To adjust the baseline pressures, please use the
following instructions:
1. Make sure you are in Monitoring Mode.
Monitoring Mode is the mode where you can
switch between °F and °C by pressing and
releasing the left button.
2. Press and hold the center button on the top of
the monitor for 5 seconds, release once you
hear a beep.
3. After the beep, you will be in Baseline Pressure
Mode and see the top left tire position blinking.
4. Select the tire position you would like to adjust
by pressing and releasing the center button on
the top of the monitor.
5. Once at the desire tire position, press the right
or left button to lower or raise the baseline tire
pressure, respectively.
6. If you wish to adjust additional baseline
pressures, repeat steps 4 and 5 until you have
adjusted all desired tires.
7. You will now need to return to Monitoring Mode.
Press and hold the center button for 5 seconds,
release once you hear a beep.
8. You should now be back in Monitoring Mode.
Confirm this by toggling the temperature using
the left button.
Add Transmitters to a New Monitor (Learn Mode)
To add your existing transmitters to a new monitor, use
the following instructions:
1. Make sure you are in Monitoring Mode.
Monitoring Mode is the mode where you can
switch between °F and °C by pressing and
releasing the left button.
2. Press and hold the left and right buttons on the
top of the 5 seconds, release once you hear a
beep.
3. After the beep you will be in Learn Mode and
see the top left tire blinking.
4. Select the tire position you would like to add by
pressing and releasing the left or right buttons
to move to different tire positions.
5. Screw the transmitter onto the corresponding
tire position. Within 12 seconds, you should
hear a beep and see the current tire pressure.
6. If you wish to add additional tire positions,
repeat steps 4 to 5 until you have added each
desired tire position.
7. You will now need to return to Monitoring Mode.
Press and hold the left and right buttons for 5
seconds, release once you hear a beep.
8. You should now be back in Monitoring Mode.
Confirm this by toggling the temperature using
the left button.
-
1
TireMinder TPMS-TRL-4 Owner's manual
- Type
- Owner's manual
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Dodge 2014 Dart Owner's manual
-
-
-
Jeep Grand Cherokee SRT8 2012 Owner's manual
-
-
-
-
Chrysler 2013 200 Owner's manual
-
-
Jeep Patriot Owner's manual