Gigabyte X570 AORUS XTREME Installation guide

- 1 -

Conguring a RAID Set (X570 Series)

RAID Levels .....................................................................................................................2

1-1ConguringSATAControllers .................................................................................... 2

A.InstallingSATAharddrive(s)inyourcomputer ....................................................... 2

B.ConguringSATAcontrollermodeinBIOSSetup .................................................. 3

C.UEFIRAIDConguration ....................................................................................... 3

1-2InstallingtheRAIDDriverandOperatingSystem .....................................................7

A.InstallingWindows ................................................................................................. 7

B.RebuildinganArray ................................................................................................ 8

- 2 -

To congure SATA hard drive(s), follow the steps below:

A. Installharddrive(s)inyourcomputer.

B. CongureSATAcontrollermodeinBIOSSetup.

C. CongureaRAIDarrayinRAIDBIOS(Note1)

D. InstalltheRAIDdriverandoperatingsystem

Before you begin

•AtleasttwoSATAharddrivesorSSDs(Note2)(toensureoptimalperformance,itisrecommendedthatyou

usetwoharddriveswithidenticalmodelandcapacity).(Note3)

•AWindowssetupdisc.

•MotherboarddriverdiscoranInternetconnectedcomputer.

•AUSBthumbdrive.

1-1 Conguring SATA Controllers

A. Installing SATA hard drive(s) in your computer

Installtheharddrives/SSDsintheSATA/M.2 connectors on the motherboard. Then connect the power

connectorsfromyourpowersupplytotheharddrives.

RAID Levels

RAID 0 RAID 1 RAID 10

MinimumNumberof

HardDrives ≥2 2 4

ArrayCapacity Numberofharddrives*

Sizeofthesmallestdrive

Sizeofthesmallestdrive (Numberofharddrives/2)*

Sizeofthesmallestdrive

FaultTolerance No Yes Yes

(Note1) SkipthisstepifyoudonotwanttocreateRAIDarrayontheSATAcontroller.

(Note2) AnM.2PCIeSSDcannotbeusedtosetupaRAIDseteitherwithanM.2SATASSDoraSATAharddrive.

(Note3) Referto"InternalConnectors,"fortheinstallationnoticesfortheM.2,andSATAconnectors.

- 3 -

Figure1

B. Conguring SATA controller mode in BIOS Setup

MakesuretoconguretheSATAcontrollermodecorrectlyinsystemBIOSSetup.

Step:

Turnonyourcomputerandpress<Delete>toenterBIOSSetupduringthePOST(Power-OnSelf-Test).Under

Settings\IO Ports, set SATA Conguration\SATA ModetoRAID(Figure1).Then savethesettings and

restartyourcomputer.(IfyouwanttouseNVMePCIeSSDstocongureRAID,makesuretosetNVMe RAID

modetoEnabled.)

C. UEFI RAID Conguration

Step1:

InBIOSSetup,gotoBoot andsetCSM SupporttoDisabled(Figure2).SavethechangesandexitBIOSSetup.

Figure2

TheBIOSSetupmenusdescribedinthissectionmaydifferfromtheexactsettingsforyourmotherboard.

TheactualBIOSSetupmenuoptionsyouwillseeshalldependonthemotherboardyouhaveand

theBIOSversion.

- 4 -

Step2:

Afterthesystemreboot,enterBIOSSetupagain.ThenentertheSettings\RAIDXpert2 Conguration Utility

sub-menu(Figure3).

Figure3

Step3:

OntheRAIDXpert2CongurationUtilityscreen,press<Enter>onArray ManagementtoentertheCreate

Arrayscreen.Then,selectaRAIDlevel(Figure4).RAIDlevelssupportedincludeRAID0,RAID1,andRAID

10(theselectionsavailabledependonthenumberoftheharddrivesbeinginstalled).Next,press<Enter>on

Select Physical DiskstoentertheSelect Physical Disksscreen.

Figure4

- 5 -

Step4:

OntheSelect Physical Disksscreen,selecttheharddrivestobeincludedintheRAIDarrayandsetthemto

Enabled.Next,usethedownarrowkeytomovetoApply Changesandpress<Enter>(Figure5).Thenreturn

tothepreviousscreenandsettheArray Size,Array Size Unit,Read Cache PolicyandWrite Cache Policy.

Figure5

Step5:

Aftersettingthecapacity,movetoCreate Arrayandpress<Enter>tobegin.(Figure6)

Figure6

-6-

Aftercompleting,you'llbebroughtbacktotheArray Managementscreen.UnderManage Array Properties

youcanseethenewRAIDvolumeandinformationonRAIDlevel,arrayname,arraycapacity,etc.(Figure7)

Figure7

Delete RAID Volume

To delete a RAID array, select thearraytobedeletedon the RAIDXpert2 Conguration Utility\Array

Management\Delete Array screen. Press <Enter>onDelete Array to enter theDelete screen.Thenset

Conrm toEnabledandpress<Enter>onYes(Figure8).

Figure8

- 7 -

1-2 Installing the RAID Driver and Operating System

WiththecorrectBIOSsettings,youarereadytoinstalltheoperatingsystem.

A. Installing Windows

AssomeoperatingsystemsalreadyincludeRAIDdriver,youdonotneedtoinstallseparateRAIDdriverduring

theWindowsinstallationprocess.Aftertheoperatingsystemisinstalled,werecommendthatyouinstallall

requireddriversfromthemotherboarddriverdiscusing"XpressInstall"orfromtheGIGABYTEAPPCenterto

ensuresystemperformanceandcompatibility.Iftheoperatingsystemtobeinstalledrequiresthatyouprovide

additionalRAIDdriverduringtheOSinstallationprocess,pleaserefertothestepsbelow:

Step1:

Method1:CopytheHw10 folderunderthe\BootDrvfolderinthedriverdisctoyourUSBthumbdrive.

Method2:GotoGIGABYTE'swebsite,browsetothemotherboardmodel'swebpage,downloadtheAMD RAID

Preinstall DriverleontheSupport\Download\SATA RAID/AHCIpage,unziptheleandcopythe

lestoyourUSBthumbdrive.

Step2:

BootfromtheWindowssetupdiscandperformstandardOSinstallationsteps.Whenthescreenrequestingyou

toloadthedriverappears,selectBrowse.

Step3:

InserttheUSBthumbdriveandthenbrowsetothelocationofthedriver.WhenascreenasshowninFigure

1appears,selectAMD-RAID Bottom DevicerstandclickNexttoloadthedriver.ThenselectAMD-RAID

ControllerandclickNexttoloadthedriver.Finally,continuetheOSinstallation.

Figure1

- 8 -

B. Rebuilding an Array

Rebuildingistheprocessofrestoringdatatoaharddrivefromotherdrivesinthearray.Rebuildingapplies

onlytofault-tolerantarrayssuchasRAID1andRAID10arrays.Toreplacetheolddrive,makesuretousea

newdriveofequalorgreatercapacity.Theproceduresbelowassumeanewdriveisaddedtoreplaceafailed

drivetorebuildaRAID1array.

Whileintheoperatingsystem,makesuretheChipsetandRAIDdrivershavebeeninstalled.Thendouble-click

theRAIDXpert2icononthedesktoptolaunchtheRAIDutility.

Step1:

EntertheloginIDandpassword(default:"admin"),

andthenclickSubmittolaunchAMD RAIDXpert2.

Step2:

IntheDisk Devicessection,left-click yourmouse

twiceonthenewly-addedharddrive.

Step3:

Onthenextscreen,selectAssign as Global Spare

andclickConrm.

Step4:

Duringtherebuildprocess,youcanselectthearray

thatisbeingbuilt(displayedinred) in the Active

Volumessectiontocheckthecurrentprogress.

Step5:

Thenrebuild is complete when the Task State

columnshows"COMPLETED."

Gigabyte X570 AORUS XTREME, X570S AERO G, X570S AORUS ELITE, X570S AORUS ELITE AX, X570S AORUS MASTER, X570S AORUS PRO AX, X570S GAMING X, X570S UD, X570SI AORUS PRO AX Installation guide

Related papers

Other documents